Tech_Data_AA55110A.pdf

COAT, ALL‐WEATHER, MAN'S WITH REMOVABLE LINER

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY

AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND

QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE

DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN

EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A

FOLLOW‐ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

ADDITIONAL INFORMATION FOR A‐A‐55110A:

PATTERN DATE: 10 JUNE 2013

SAMPLE SIZE: 40 REG

THE FOLLOWING INFORMATION PERTAINS TO CLOTH

USED AS SHELL MATERIAL:

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER AND

COTTON (WATER REPELLENT), CG BLUE SHADE 3376,

CONFORMING TO A‐A‐50531, IS AVAILABLE ON ROLL

NO. 113220, AND APPLICABLE FOR SHADE.

THE FOLLOWING INFO IS FOR CLOTH LINING MATERIAL

STANDARD SAMPLE FOR NYLON TAFFETA CLOTH, CG BLUE

SHADE 3376 IS AVAILABLE ON ROLL NO. 85018, AND

APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

INTERIM CHANGES TO A‐A‐55110A:

PAGE 2, DESCRIPTION:

‐ PARA 1, LINE 2, AFTER "BACK," DELETE "A LINED"

‐ PARA. 1, LINE 3, AFTER "BACK YOKE," ADD "RIGHT

FRONT GUN FLAP,".

‐ PARA. 3, LINE 3, DELETE "STORM YOKE," INSERT "BACK YOKE, GUN FLAP"

PARA.3, AT THE END OF THE PARAGRAPH ADD THE

FOLLOWING: "AS AN ALTERNATE BELTS COULD BE TOP‐

STITCHED WITH A DOUBLE NEEDLE MACHINE. THE EDGE

STITCHING SHALL BE ONE‐SIXTEENTH (1/16) AND FIVE

SIXTEENTH INCH (5/16) FROM THE BELT EDGE."

‐PARA. 5, LINES 1 AND 2, DELETE "SQUARE‐OR

TAPERED END TYPE, "AND SUBSTITUTE "EYELET‐END

SQUARE BAR TYPE"

‐ PARA. 5, LINE 3, AFTER "UNDERSIDE.", ADD "THE

END OF THE BUTTONHOLE SHALL BE BARTACKED IN A

SEPARATE OPERATION FROM BUTTONHOLE MAKING,

SECURELY CATCHING THE ENDS OF THE GIMP COVERING

WIDTH OF THE BAR."

‐ AFTER PARA 5, INSERT THE FOLLOWING NEW PARAGRAPH: "FRONT FACING BAR TACKING ‐ THE FRONT

FACING SHALL BE TACKED USING A 1/2 INCH BARTACK POSITIONED AT THE POCKET BOTTOM (WHERE

POCKET AND FACING MEET) AND SHALL BE TACKED THROUGH THE FACING AND POCKET (NOT TO

INCLUDE THE SHELL).

PAGE 2, MATERIAL:

AT THE END OF THE PARAGRAPH ADD THE FOLLOWING SENTENCE:

'AS AN ALTERNATE, CLOTH SHALL BE SINGLE PLY,

65 PERCENT POLYESTER 35 COTTON POPLIN CLOTH

TESTED IN ACCORDANCE WITH TABLE II OF A‐A‐50531"

PAGE 3, AFTER PARA."BASIC MATERIAL" ADD

"TOXICITY. THE CLOTH SHALL SHOW NO TOXICITY WHEN

TESTED USING THE METHODS BELOW:

A) TITLE 40, CODE OF FEDERAL REGULATIONS, 1994

EDITION

SECTION 798.4100 ‐ DERMAL SENSITIZATION

SECTION 798.4470 ‐ PRIMARY DERMAL IRRITATION

SECTION 798.4500 ‐ PRIMARY EYE IRRITATION

MARZULLI, F & H. MAIBACH "CONTACT ALLERGY:

PREDICTIVE TESTING IN HUMANS",

ADVANCES IN MODERN TOXICOLOGY, VOLUME 4,

PG. 353‐372, 1977

B) AS AN ALTERNATIVE TO ANIMAL AND HUMAN TESTING

CERTIFIES THAT THE CLOTH IS COMPOSED OFCHEMICALS

AND/ORMATERIALS WHICH HAVE BEEN SAFELY USED

COMMERCIALLY WHERE PROLONGED SKIN CONTACT HAS

OCCURRED

PAGE 3, MATERIAL:

‐ PARA. 1, LINE 1, AFTER "THE MATERIAL FOR THE",

ADD "BACK SLEEVE LINING, FRONT SLEEVE LINING AND

THE".

‐ PARA. 2, AFTER "THE MATERIAL" INSERT "FOR THE REMOVABLE LINER"

‐ PARA. 2, LINE 2, DELETE "80 YARNS PER INCH

(MIN)" AND SUBSTITUTE "68 YARNS PER INCH (MIN)".

‐ PARA. 2, LINE 5, DELETE THE SENTENCE BEGINNING

WITH "THE FINISHED MATERIAL....." ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"THE FINISHED MATERIAL SHALL MATCH BLUE 3376 AND 'GOOD' FASTNESS TO PERSPIRATION

ACCORDING TO AATCC TEST METHOD 15

(THE TEST FOR COLORFASTNESS FOR ACID & ALKALINE

SOLUTION SHALL APPLY); WET DRY‐CLEANING ACCORD‐

ING TO FED‐STD‐191 METHOD 5622; LAUNDERING

ACCORDING TO AATCC TEST METHOD 61‐TEST 3A 1/ 2/;

AND A CROCKING RATING NOT LOWER THAN 3.0 ACCORD‐

ING TO AATCC‐TEST METHOD 8.

1/ THE SPECIMEN MUST BE DRIED AFTER EACH OF THE

THREE LAUNDERING CYCLES. THE SOAP SOLUTION

SHALL CONTAIN 0.5 PERCENT BY WEIGHT P‐D‐245

DETERGENT, LAUNDRY, AND HAND DISHWASHING

(GRANULAR) TYPE II, IN WATER HARDNESS NOT OVER

50 PARTS PER MILLION. THE WEIGHT OF THE

SPECIMEN SHALL BE 4.0 +/‐ 0.5 GRAMS AND THE

ROTATING TIME SHALL BE 30 MINUTES WITH TEN

STAINLESS STEEL BALLS IN EACH CYLINDER.

2/ FOR THE COLOR TRANSFER CLOTH EVALUATION,

ONLY THE STAIN ON THE COTTON FIBERS OF THE COLOR

TRANSFER CLOTH SHALL BE EVALUATED."

BEFORE "FUSIBLE INTERLINING" INSERT THE FOLLOWING PARAGRAPH, "Color matching. The color and appearance of the cloth shall match the standard sample when viewed using AATCC Evaluation

Procedure 9, Option A. Filtered tungsten lamps that approximate artificial daylight D75 illuminant having a color temperature of 7500 ± 200 K with illumination of 100 ± 20 foot candles shall be used. The color and appearance shall be a good match to the standard sample under Incandescent A light having a color temperature of 2854 ± 200 K."2

PAGE 3, FUSIBLE INTERLINING (NON‐WOVEN).LINE 1;

AFTER "THE TOP COLLAR", ADD "COLLAR STAND".

PAGE 3, FUSIBLE INTERLINING (NON‐WOVEN), PARA 1,

LINE 10, AFTER "BLACK" ADD "OR, AS AN ALTERNATE,

CHARCOAL".

PAGE 4:

‐ "FUSIBLE INTERLINING (WOVEN)". DELETE ITS ENTIRE

CONTENTS WITH NO SUBSTITUTION.

‐ "BUTTONS" PARAGRAPH, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"BUTTONS. THE BUTTONS SHALL BE TYPE II, STYLE

20/21, PEARLESCENT‐POLYESTER COMPOSITION, 30 AND

40 LINE OF V‐B‐871 OR EQUAL. AS AN ALTERNATE, THE BUTTONS SHALL CONFORM TO TYPE II, CLASS D, MELAMINE FORMELDAHYDE COMPOSITION, STYLE 20/21, 30 AND 40 LINE, OF V‐B‐871.

THE COLOR SHALL BE BLUE BU, CABLE NO. 62002 AS SHOWN IN DEPARTMENT OF DEFENSE SHADES FOR

BUTTONS, 1966.

THE BUTTONS SHALL HAVE A GLOSSY FINISH.

THE REINFORCEMENT BUTTONS SHALL BE 18 LINE, TYPE II, STYLE 15, SHADE BLACK

OF V‐B‐871 OR EQUAL."

‐ "BUCKLES" PARAGRAPH, LINE 3, AFTER "EDGE.",

DELETE THE FOLLOWING SENTENCE AND SUBSTITUTE

"THE COLOR SHALL BE BLUE BU, CABLE NO. 62002,

WITH A MATTE FINISH." DELETE LAST SENTENCE OF

PARAGRAPH AND ALL BUCKLE DIMENSIONS & SUBSTITUTE

"THE NOMINAL DIMENSIONS SHALL BE IN INCHES AS

SPECIFIED BELOW:

. BELT SLEEVE STRAP

LENGTH (OUTSIDE) 2 1/2 1 1/2

WIDTH (OUTSIDE) 1 3/8 1 1/8

LENGTH (INSIDE) 1 7/8 1

WIDTH (INSIDE) 7/8 5/8

CENTER BAR WIDTH 1/4 1/8"

PAGES 6 & 7, MEASUREMENTS., IN "BELT LENGTH"

COLUMN FOR "SHORTS, REGULARS, & LONGS", OPPOSITE

SIZES 34 THROUGH 48, SUBTRACT 2 INCHES FROM EACH

MEASUREMENT.

PAGES 6 & 7, MEASUREMENTS, "SHORT" AT THE BOTTOM OF THE COLUMNS, ADD THE FOLLOWING

SIZES AND MEASUREMENTS:

50‐‐‐‐‐‐58‐‐‐‐‐‐17‐‐‐‐‐‐41‐1/4‐‐‐‐‐‐31‐1/4‐‐‐‐‐‐60‐1/2

52‐‐‐‐‐‐60‐‐‐‐‐‐17‐‐‐‐‐‐41‐1/2‐‐‐‐‐‐31‐1/2‐‐‐‐‐‐62‐1/2

54‐‐‐‐‐‐62‐‐‐‐‐‐17‐‐‐‐‐‐41‐3/4‐‐‐‐‐‐31‐3/4‐‐‐‐‐‐64‐1/2

"REGULAR" AT THE BOTTOM OF THE COLUMNS, ADD THE FOLLOWING SIZES AND MEASUREMENTS:

50‐‐‐‐‐‐58‐‐‐‐‐‐18‐‐‐‐‐‐43‐1/4‐‐‐‐‐‐33‐1/4‐‐‐‐‐‐60‐1/2

52‐‐‐‐‐‐60‐‐‐‐‐‐18‐‐‐‐‐‐43‐1/2‐‐‐‐‐‐33‐1/2‐‐‐‐‐‐62‐1/2

54‐‐‐‐‐‐62‐‐‐‐‐‐18‐‐‐‐‐‐43‐3/4‐‐‐‐‐‐33‐3/4‐‐‐‐‐‐64‐1/2

"LONG" AT THE BOTTOM OF THE COLUMNS, ADD THE FOLLOWING SIZES AND MEASUREMENTS:

50‐‐‐‐‐‐58‐‐‐‐‐‐19‐1/4‐‐45‐1/4‐‐‐‐‐‐35‐1/4‐‐‐‐‐‐60‐1/2

52‐‐‐‐‐‐60‐‐‐‐‐‐19‐1/4‐‐45‐1/2‐‐‐‐‐‐35‐1/2‐‐‐‐‐‐62‐1/2

54‐‐‐‐‐‐62‐‐‐‐‐‐19‐1/4‐‐45‐3/4‐‐‐‐‐‐35‐3/4‐‐‐‐‐‐64‐1/2

"EXTRA‐LONG" AT THE BOTTOM OF THE COLUMNS, ADD THE FOLLOWING SIZES AND MEASUREMENTS:

50‐‐‐‐‐‐58‐‐‐‐‐‐20‐‐‐‐‐‐47‐1/4‐‐‐‐‐‐37‐1/4‐‐‐‐‐‐60‐1/2

52‐‐‐‐‐‐60‐‐‐‐‐‐20‐‐‐‐‐‐47‐1/2‐‐‐‐‐‐37‐1/2‐‐‐‐‐‐62‐1/2

54‐‐‐‐‐‐62‐‐‐‐‐‐20‐‐‐‐‐‐47‐3/4‐‐‐‐‐‐37‐3/4‐‐‐‐‐‐64‐1/2

PAGE 9, UNDER "COMPONENT TESTING", DELETE ALL

REFERENCE TO "WOVEN INTERLINING FUSED TO BASIC

CLOTH" AND ITS ENTIRE CONTENTS.

PAGE 11, UNDER COLLAR, LAPEL, EPAULET, OR SLEEVE

STRAPS. ADD "EPAULET POINT MORE THAN 1/2 INCH

FROM GORGE OF NECK.

PAGE 14‐15, DELETE "PACKAGING," AND "PACKING" PARAGRAPHS IN THEIR ENTIRETY. AND INSERT THE

FOLLOWING: PACKAGING AND MARKING INSRUCTIONS

EACH COAT SHALL BE FOLDED TO APPROXIMATELY 14

INCHES BY 22‐1/2 INCHES. EACH FOLDED COAT SHALL

BE INSERTED INTO A CLOSE FITTING FLAT STYLE

CLEAR POLYETHYLENE BAG CONFORMING TO A‐A‐50083

THE BAG SHALL BE AT LEAST 1 INCH LONGER THAN THE

FOLDED COAT. THE UNSEALED OPENING OF THE BAG

SHALL BE AT THE SMALLER DIMENSION OF THE BAG

TEN COATS OF ONE SIZE ONLY, PACKAGED AS SPEC‐

IFIED, SHALL BE PACKED IN A SHIPPING CONTAIN‐

ER THAT IS ASSEMBLED AND CLOSED TO MIL‐B‐17757.

THE FIBERBOARD FOR THE LINERS SHALL CONFORM TO

TYPE CF, CLASS DOMESTIC, VARIETY DW, GRADE 275

OF PPP‐F‐320. EACH BAGGED COAT SHALL BE PACKED

FLAT, WITH EVERY OTHER COAT REVERSED TOP TO

BOTTOM WITHIN THE CONTENTS OF THE SHIPPING

CONTAINER. THE TOP AND THE BOTTOM OF THE CON‐

ENTS OF THE SHIPPING CONTAINER SHALL BE COM‐

PLETELY COVERED WITH WITH A SHEET OF 30 POUND

(MIN) BASIS WEIGHT PAPER CONFORMING TO A‐A‐203

PAGE 15, "MARKING," AFTER "MIL‐STD‐129," DELETE THE REMAINDER OF THE PARAGRAPH.

(Ref. W1958)

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR‐CODED WITH A PAPER TAG FOR PERSONAL

CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A

BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT

PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE.

THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO

THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED.

THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT

CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN‐READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG ‐ USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL‐

DTL‐32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF

MIL‐DTL‐32075.

AQLS FOR COMMERCIAL ITEM DESCRIPTION (CIDS)

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

PALLETIZATION 6.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLE FOR

INSPECTION BY ATTRIBUTES". ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL II

(Ref. T7520)

ADDITIONAL INFORMATION FOR A‐A‐50531:

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER

AND COTTON (WATER REPELLENT), ARMY BLACK 385

CONFORMING TO A‐A‐50531, IS AVAILABLE ON ROLL

NO. 3814, AND APPLICABLE FOR SHADE, FINISH AND

COLORFASTNESS.

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER AND

COTTON (WATER REPELLENT), MARINE CORPS PEWTER

2246 CONFORMING TO A‐A‐50531, IS AVAILABLE ON

ROLL NO. 1208‐06, AND APPLICABLE FOR SHADE, FINISH

AND COLORFASTNESS.

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER

AND COTTON (WATER REPELLENT), COAST GUARD BLUE

3376 CONFORMING TO A‐A‐50531, IS AVAILABLE ON

ROLL NO. 113220 APPLICABLE FOR SHADE,

FINISH, AND COLORFASTNESS.

INTERIM SPECIFICATION CHANGES

TO A‐A‐50531:

PAGE 1, PARA. 1.1, GENERAL, AT THE END OF THE

PARAGRAPH, ADD THE FOLLOWING SENTENCE:

"AN ALTERNATE CLOTH SHALL BE A 1 PLY, 65 +/‐ 3

PERCENT POLYESTER AND 35 +/‐ 3 PERCENT

COTTON POPLIN CLOTH.

PARAGRAPH 1.2, PHYSICAL REQUIREMENTS, SECOND

LINE, AFTER "I", DELETE THE PERIOD AND ADD "AND

TABLE II."

TABLE I. CHANGE TITLE OF TABLE FROM "PHYSICAL

REQUIREMENTS" TO "BASIC CLOTH PHYSICAL

REQUIREMENTS" (2 PLY).

PAGE 2, TABLE I, BASIC CLOTH PHYSICAL REQUIRE‐

MENTS (2 PLY), UNDER TEST METHODS, DELETE "5550"

AND SUBSTITUTE "5556" FOR DIMENSIONAL STABILITY

TEST.

PAGE 3, BEFORE TABLE I FOOTNOTES, ADD THE

FOLLOWING NEW TABLE:

TABLE II. ALTERNATE CLOTH PHYSICAL REQUIREMENTS

(1 PLY)

CHARACTERISTICS REQUIREMENTS TEST METHOD

FIBER CONTENT 65% +/‐ 3% POLYESTER 2100 4/

. 35% +/‐ 3% COTTON 2100 4/

YARN PLY

. WARP SINGLES OR 2 PLY VISUAL 2/

. FILLING SINGLES VISUAL 2/

WEIGHT, OZ./SQ.

YD. 5.3‐6.8 ASTM D 3776 3/

YARNS PER INCH (MIN.)

. WARP 107 ASTM D 3775 3/

. FILLING 68 ASTM D 3775 3/

WEAVE PLAIN VISUAL 2/

AIR PERMEABILITY

(MAX.) 10 ASTM D 737.75 3/

BREAKING STRENGTH, LBS. (MIN.)

. WARP 185 ASTM D 1682 3/

. FILLING 70 ASTM D 1682 3/

TEARING STRENGTH, LBS. (MIN.)

. WARP 5.0 ASTM D 5034 3/

. FILLING 2.0 ASTM D 5034 3/

DIMENSIONAL STABILITY, PERCENT (MAX.)

. WARP 2.0 5556 4/

. FILLING(1 PLY) 3.0 5556 4/

COLORFASTNESS TO:

LAUNDERING

(3 CYCLES) GOOD 5610 4/ 5/

PERSPIRATION GOOD 5680

CROCKING

. WET 2.5 5651 AND

. DRY 2.5 AATCC 8 4/ 8/

LIGHT

(40 HOURS) GOOD 5660 4/

PH 5.0‐8.0 2811 4/

SPRAY RATING:

. INITIAL 100,100,90 5526 4/

. AFTER 3

LAUNDERINGS 70,70,70 5526 4/

. 1 DRY‐

CLEANING 70,70,70 5508 AND 5526 4/

DYNAMIC ABSORPTION, PERCENT (MAX.)

. INITIAL 18 5500 4/

. AFTER 3

. LAUNDERINGS 18 5556 AND 5500 4/ 7/

HYDROSTATIC PRESSURE

. CM. (MIN.)

. INITIAL 30 5514 4/

. AFTER 3

LAUNDERINGS

(COTTON METHOD) 25 5556 AND 5514 4/ 7/

. AFTER 1

DRY CLEANING 25 5508 ABD 5514 4/

RESISTANCE TO ORGANIC

LIQUID (MIN.)

. INITIAL NO WETTING AATCC 118 8/

. (N‐TETRADECANE)

. AFTER 3

LAUNDERINGS

(COTTON METHOD) NO WETTING 5556 AND 7/

. AATCC 118 8/

WATER REPELLENT 9/

THE FOLLOWING FOOTNOTES SHALL APPLY TO BOTH

TABLE I AND TABLE II."

PAGE 4, PARAGRAPH 1.3, PUT UP., LINE 2, DELETE

"50 AND SUBSTITUTE "40".

PAGE 8, UNDER "REVIEW ACTIVITY", ADD THE

FOLLOWING: "NAVY ‐ NU".

(Ref. T0495)

LIST OF APPROVED WATER REPELLENT TREATMENTS FOR MILITARY FABRICS 1/

THE FOLLOWING FLUOROCHEMICALS ARE APPROVED "DURABLE" TYPE WATER REPELLENT TREATMENTS

FOR USE ON MILITARY FABRICS. THEY MAY BE USED ALONE OR COMBINED WITH AN APPROVED

EXTENDER COMPONENT TO PRODUCE A "QUARPEL" TYPE OF WATER REPELLENT TREATMENT

REPELLENT TREATMENTS:

TRADE NAME SUPPLIER

AURAPEL FC‐340 AURALUX DIV OF SYBRON

CHEMICAL CO.

P.O. BOX 113

YANTIC, CT 06389

TEL: 860‐886‐2626

BARPEL 1700 APOLLO CHEMICAL CORP.

PO BOX 2176

BURLINGTON, NC 27215

TEL: 910‐226‐1161

CHEMSHIELD 939 CHEM‐TEX INC.

WR 930 P.O. BOX 1105

1891 N. COLUMBIA ST.

BLDG 106, MILLEDGEVILLE, GA 31061

TEL: 336‐578‐5476

FABRIC GUARD ML TANNER CHEMICAL CO., INC.

PO BOX 1967, FURMAN HALL

COURT, GREENVILLE, NC 29602

TEL: NO LISTING IN NC ON 800#

ZONYL B CIBA‐GEIGY CORP.

ZONYL D P.O. BOX 11422

ZONYL RN 2/ HIGHPOINT, NC 27409

ZONY 6700 TEL: 888‐396‐2488

ZONYL 6700 GF

ZONYL 7040

ZONYL 8300

ZONYL 8070

ZONYL DWR

ZONYL MIL

FC‐232 3M CORPORATION,

FC‐251 PROTECTIVE PRODUCTS DIV.

FC‐461 ST. PAUL, MN. 02895

FC‐831 TEL: 612‐737‐0098

REPEARL F‐14N MITSUBISHI INTERNATIONAL

REPEARL F‐35 520 MADISON AVE.

REPEARL F‐31 NEW YORK, NY 10022

TEL: 212‐605‐2440

800‐851‐5765

NK GUARD FG‐280 NICCA USA, INC.

P.O. BOX 1600

5000 NELSON ROAD

FOUNTAIN INN, SC 29644

TEL: 864‐862‐1426

SEQUAPEL CQR SEQUA CHEMICAL CORP.

SEQUAPEL NRL ONE SEQUA DRIVE

SEQUAPEL WOR CHESTER, SC 29807‐0070

SEQUAPEL WOR‐46 TEL: 803‐385‐5181

TEX‐TEL NI‐40 AUTO CHEMICAL CO.

THREE PARKWAY

PHILADELPHIA, PA 19102

TEL: 215‐419‐7000

UNIGUARD‐5061 UNICHEM INC.

P.O. BOX 612

916 W. MAIN ST.

HAW RIVER, NC 27258

TEL: 336‐578‐5476

FLUOROGARD 1700 PUTNAM INDUSTRIES, INC

197 RIDGEWOOD AVE.

GLEN RIDGE, NJ 07028

TEL: NOT LISTED

FLO CHEM EXTRA 17‐4 EMCO SERVICES INC.

P.O. BOX 2191

TAUNTON, MA 02780

TEL: 508‐823‐8852

1/ A SEPARATE LIST OF APPROVED WATER REPELLENT TREATMENTS EXISTS FOR FABRICS CONFORMING

TO CLOTH, CAMOUFLAGE PATTERN; WOODLAND, COTTON AND NYLON, CLASS 2, MIL‐C‐44031 AND

CLOTH, TWILL, CAMOUFLAGE PATTERN, COTTON AND NYLON FOR DESERT UNIFORM, CLASS 1A, MIL‐C‐

44034.

2/ FOR POLYESTER, NYLON AND BLENDS OF MANMADE FIBERS ONLY.

ADDITIONAL INFORMATION FOR A‐A‐55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP".

RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN

TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT

ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS

THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

V‐B‐871F Button, Sewing Hole, and Button, Staple, (plastic) has been canceled and is superseded by A‐

A‐59994 Button, Sewing Hole, and Button, Staple, (Plastic) dated 04 Dec 2018

No Information Follows

ADDITIONAL INFO FOR NN‐P‐71: NO ADDITIONAL INFORMATION FOLLOWS..

(Ref. T0829 ‐ 9/11/06)

"MIL‐DTL‐32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD‐L‐20

(Ref. T0451 ‐ June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL‐DTL‐32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR MIL‐P‐15011:

NO ADDITIONAL INFORMATION FOLLOWS.

(ref. T1368 ‐ 6/15/06)

ADDITIONAL INFORMATION FOR MIL‐I‐45208:

NOTE: MIL‐I‐45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL

STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286 )

ADDITIONAL INFORMATION FOR FED‐STD‐191:

FED‐STD‐191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT

USING FED‐STD‐191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED‐STD‐191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE

CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH

OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE

CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE

DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE

"B‐97" AND SUBSTITUTE "B‐91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS

REQUIRE THE USE OF 1,1,1‐ TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1‐TRICHLORETHANE IS AN

OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF

EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED

DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3

DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED

FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES

WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER

FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8:

DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE

WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH

AND PLACED IN A PRE‐HEATED DRYER HAVING A STACK TEMPERATURE OF 140‐180 DEG. F. THIS

TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON

THE DRYER. DRYING SHALL CONTINUE FOR 45‐60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING

TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS

ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE

SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE‐HEATED DRYER HAVING A

STACKTEMPERATURE OF 140‐180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF

"HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35‐40

MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER

NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND

SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+‐". LINE 6: AFTER "TO" ADD "+‐".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A

SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE

SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE

RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST

RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20

SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS

IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL

BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE

AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:

"RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE

MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE

POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE

AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP

& FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE

OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH

VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC

SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND

FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE)

IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED

WHETHER THE FABRIC ISACCEPTABLE OR NON‐ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR

EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST."

(Ref. T0215)

MIL‐STD‐129R w/CHANGE 2 ‐ DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR

SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL)

SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY

REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST

SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL‐STD‐147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS