Statement of Work (SOW) - Hopi Health Care Center - GE CARESCAPE Equipment.pdf

Hopi Health Care Center - GE Healthcare CARESCAPE Patient Monitoring Equipment

Statement of Work

Project Title: Hopi Health Care Center – GE Healthcare CARESCAPE Patient Monitoring Equipment

1. Introduction and Background

The Indian Health Service (IHS), Phoenix Area Office (PAO) Department of Acquisition Management (DAM), is procuring for a Contractor to provide equipment and technical services necessary to install new GE Healthcare CARESCAPE physiologic monitoring system equipment at Hopi Health Care Center (Keams Canyon Service Unit).

Physiologic monitoring equipment measures and displays waveforms and numerical data for various patient parameters, including but not limited to electrocardiogram (ECG), noninvasive blood pressure (NIBP), respiratory rate, invasive blood pressure (IBP), body temperature, arterial hemoglobin oxygen saturation (SpO2), mixed venous oxygenation (SvO2), cardiac output, end-tidal carbon dioxide (ETCO2), intracranial pressure, and airway gas concentrations. Physiologic monitoring systems are critically important to patient care and provide real-time measurements of monitored parameters and notification of changes in a patient's condition. Hopi Health Care center requires the installation and implementation of the GE Healthcare CARESCAPE platform in the Emergency Department, Short-Stay, and Obstetrics Ward (OB) patient care areas, allowing both basic and advanced monitoring capabilities. The GE CARESCAPE physiologic monitoring equipment requires specialized installation and training services by certified GE Healthcare field specialists and technicians to ensure that the devices are configured to meet manufacturer’s requirements and Hopi Health Care Center end users are fully trained in proper use of the equipment. The Indian Health Service PAO intends to procure new GE Healthcare CARESCAPE equipment and installation services by original equipment manufacturers (OEM) certified/trained equipment specialists that meet the appropriate specification and standards set by the Food and Drug Administration (FDA), National Fire Protection Association (NFPA), and The Joint Commission (TJC).

2. Service and Equipment Requirements

The Contractor shall provide GE Healthcare certified personnel to perform comprehensive on-site visits to Hopi Health Care Center, in order to install new GE Healthcare CARESCAPE physiologic monitoring system equipment and configure the device hardware and software to optimal operation. Specific tasks and requirements include the following:

2.1 - Delivery, installation, and configuration of the new GE Healthcare CARESCAPE equipment:

The Contractor shall install and configure all new CARESCAPE devices to operate inside the Hopi Health Care Center patient care areas. The Contractor shall deliver, install, and certify all devices to fully comply with all relevant GE Healthcare installation criteria and technical standards. All devices shall be new condition, factory assembled/configured, and include a factory warranty. The Contractor shall warrant all workmanship. At a minimum, all CARESCAPE physiological monitors shall receive a standard warranty of 3 years parts and 1 year labor. All CARESCAPE central stations and network hardware/software shall receive a standard warranty of 1 year parts and labor. All applicable licenses, training, shipping/handling fees and software modules shall be included in this procurement. A complete list of all CARESCAPE devices (hardware/software) and services required in this procurement is listed in Section 13 - CARESAPE Equipment and Services. The Contractor shall provide and install the following GE Healthcare CARESCAPE equipment:

2.1.1 GE Healthcare CARESCAPE B450 Multi-Parameter Patient Monitors CARESCAPE B450 V3.1 (Wall Mounted/Without WLAN) – QTY 9 CARESCAPE B450 V3.1 (Transport/with WLAN) – QTY 3

Equipment Description: The CARESCAPE B450 is a multi-parameter patient monitor intended for use in multiple areas and intra hospital transport within a professional healthcare facility. The CARESCAPE B450 is intended for use on adult, pediatric, and neonatal patients and on one patient at a time. The CARESCAPE B450 is indicated for monitoring of hemodynamic, respiratory, and neurophysiological status. The CARESCAPE B450 can be a stand-alone monitor or interfaced to other devices. It can also be connected to other monitors for remote viewing and to data management software devices via a network. The CARESCAPE B450 is able to detect and generate alarms for ECG arrhythmias also shows alarms from other ECG sources. The CARESCAPE B450 also provides other alarms, trends, snapshots and events, and calculations, and can be connected to displays, printers and recording devices. The Contractor shall install total of (5) wall mounted B450 patient monitors in Obstetrics Ward and (4) wall mounted B450 patient monitors in the Short- Stay patient care areas. These patient monitors shall be hard-wired and installed for complete patient beside configuration. The Contractor shall also provide (3) transport B450 patient monitors with wireless capabilities. The Contractor shall provide all CARESCAPE patient data modules, software packages/licenses, options, and upgrades listed in Section 13 – CARESAPE Equipment and Services.

2.1.2 GE Healthcare CARESCAPE Central Station (CSCS)

CARESCAPE Central Station V2 MAI 700 ATO model – QTY 5 Equipment Description: The GE Healthcare CARESCAPE Central Station is capable of displaying physiologic monitoring measurements from any GE CARESCAPE device connected to the system.

The GE Healthcare CSCS alarms when set limits on any CARESCAPE bedside monitor within the system are exceeded. The GE CARESCAPE central station monitors are capable of simultaneously displaying all waveforms from any one patient without interrupting the display of any other patient's ECG waveform. Communications capability between the GE Healthcare CARESCAPE central station and each CARESCAPE B450 bedside monitor is essential. The Contractor shall provide (3) Carescape v2.x All-in-one Central Stations for the Emergency Department (ED), Obstetrics (OB) Ward, and Short-Stay patient care areas. Each nurse station in the ED, OB, and Short-Stay departments shall have (2) central stations, allowing each department to see all patients currently being monitored on the CARESCAPE platform. The Contractor shall provide all licenses, software packages, and installation/configuration services required to monitor all installed CARESCAPE devices at Hopi Health Care Center. The Contractor shall provide all CARESCAPE Central Station software packages/licenses, PC hardware/software, and on-site/remote configuration services listed in Section 13 – CARESAPE Equipment and Services.

2.1.2 GE Healthcare CARESCAPE Networking

CARESCAPE Wireless Networking

CARESCAPE Network Equipment Equipment Description: The Contractor shall provide network design and consultation services necessary to successfully implement all CARESCAPE devices on the CARESCAPE Mission Critical (MC) Network. The Contractor shall provide network fiber run, network drop install, and configuration services for inter-VLAN routing for all CARESCAPE devices. The Contractor shall provide all planning. The Contractor shall provide all CARESCAPE networking equipment and services listed in Section 13 – CARESAPE Equipment and Services.

2.1.3 GE Healthcare CARESCAPE Education

Patient Monitoring Clinical Applications Training Equipment Description: The Contractor shall provide on-site education services to the Hopi Health

Care Staff on the features and operations of the CARESCAPE Central Station and CARESCAPE patient monitors. The Contractor shall provide on-site education and support necessary to configure all CARESCAPE devices to Hopi Health Care Center requirements. The Contractor shall provide

(8) days of Patient Monitoring Clinical Applications Training. The Contractor shall provide all CARESCAPE education and support services and resources listed in Section 13 – CARESCAPE Equipment and Services

2.1.4 GE Healthcare CARESCAPE Hl7 Services

HL7 (Health Level 7) Standard Integration development/support services shall be provided to integrate the CARESCAPE system products to the Indian Health Service Resource and Patient Management System (RPMS). The Indian Health Service (IHS) Support for Health Level Seven (HL7) Interfaces software package (BHL) provides a way for Resource and Patient Management

System (RPMS) applications to exchange health-care data with commercial off-the-shelf and other applications using the HL7 protocol. The Contractor shall develop a customized interface between the GE Healthcare Mission Critical (MC) Network and Resource and Patient Management System (RPMS). The Contractor shall customize the interface to provide a mechanism to successfully exchange information between the devices on the hospital’s enterprise network (RPMS server, NTP server) and the devices on the CARESCAPE Network MC (iCentral, iCentral Clients, Central Station, patient monitors).

2.2 – Documentation of services performed and supporting documents The Contractor shall provide a detailed service report indicating services performed and include pertinent information such as equipment identification (serial number and device type) and equipment location. The Contractor shall provide all supporting documents upon request including service manuals, user manuals, and technical data sheets.

3. General Requirements

The services/work that the Contractor shall provide specifically includes those described in Section 2 or specified herein.

However, the performance as described and specified shall not be deemed to constitute a detailed specification having the effect of excluding other needed work not specifically mentioned that will be necessary for the successful completion of this project as generally described. The Contractor is required to furnish all services necessary to successfully fulfill the overall objectives set forth in the contract.

Complete installation, configuration, testing, and programming services shall be provided by the Contractor for all CARESCAPE devices procured in this award to ensure full operation of the GE Healthcare CARESCAPE patient monitoring platform.

The Contractor shall maintain a current list of the GE Healthcare CARESCAPE devices installed at the Hopi Health Care Center and shall provide an updated list to the Contracting Officer Representative (COR) upon request. This list must include the following information: current technical specifications of the GE Healthcare CARESCAPE devices, current software versions, and device information (device type, serial number, location, and current configuration).

Contractor personnel shall check-in with the Hopi Health Care Center Biomedical Engineering Department or Facilities Engineering Department before beginning any work. Contractor shall call or email the Keams Canyon Service Unit staff and coordinate with the department leads during project implementation.

The contractor shall provide all services during normal operating hours Monday through Friday from 8:00 a.m. to 4:30 p.m. excluding the weekend and federal holidays. Service schedule shall be agreed to by the contractor and the designated

COR.

The Contractor shall uninstall and remove all current physiologic monitoring system equipment necessary to implement the CARESCAPE platform. The Contractor shall inform the local biomedical engineering and property department of all equipment removed from service. The Hopi Health Care Center Inventory Property Specialist and Biomedical Equipment Technician will coordinate with the Contractor to generate an accurate list of medical equipment being removed from the building. The Contractor shall remove all trash, discarded parts, dunnage, and other material from areas immediately after completion of installation. Government-owned dumpsters may be used for disposal of this nonhazardous waste material.

The general area shall be left in a clean and orderly condition free of any foreign material caused by the installation or repair activities.

The contractor shall provide on-site visits for all services listed herein including installation/configuration of CARESCAPE devices, networking, and education services. The contractor shall furnish all necessary tools, consumables, software and test equipment to pursue the fulfillment of work performed under this Statement of Work.

The Contractor shall warrant all workmanship. The warranty will remain free from defects as follows: at a minimum, standard warranty is 1 year parts and labor unless otherwise specified in the product manual and/or Seller’s quotation.

The Contractor shall provide training such that all patient care providers (end-users) and biomedical technicians completing the training are qualified to operate the CARESCAPE devices.

The Contractor shall provide all shipping and handling services necessary to deliver and install the GE Healthcare CARESCAPE equipment. Equipment shall be delivered by standard freight and liftgate delivery service shall be provided upon request. The Contractor shall inform the COR and local service unit point of contacts of shipping updates and provide notification of shipment within 24 hours.

All equipment and materials provided by the Contractor shall be new and, where appropriate, shall arrive on-site sealed in original manufacturer’s containers. The Government reserves the right to refuse any items deemed to not meet this requirement. The Contractor shall provide tools, labor and any test equipment for installation and removal of old equipment from the premises.

4. Contractor Personnel Requirements

The Contractor shall provide GE Healthcare certified service personnel with experience in maintenance, installation and testing of the GE CARESCAPE equipment types listed herein. Personnel must be qualified to perform the required installation and training services for all listed equipment (see Section 13 – Carescape Equipment and Services). In the event a service representative is unable to fulfill all services listed herein, the Contractor shall provide a senior service engineer, or like, to resolve any problems. All workmanship performed by the Contractor shall be of acceptable industry standard quality and shall be immediately rectified at no additional cost to the Government upon notification of non-acceptability by the Government. Valid documentation of GE Healthcare certification and current manufacturer’s authorization to perform technical support, installation, and maintenance on the items listed in Section 13 shall be submitted to the COR upon request.

5. Contractor Requirements

The Contractor shall provide all needed supplies, parts, materials, equipment, and tools that are necessary for the performance of the contract requirements. The Contractor shall be held responsible for the cost of any necessary repairs or equipment replacements caused by negligence and abuse on his/her part. The Contractor shall be responsible for the cost for safeguarding all Government property that will be serviced under this contract. If applicable, the Contractor shall be responsible for replacing, purchasing, and disposing of bio-hazardous sources, and shall consider such services a regular part of this contract.

6. Reporting Requirement and Deliverables

6.1 Service Reports – Delivery Tickets: The Contractor shall instruct its service representatives to obtain a signature from the COR or designee official responsible for the equipment on a service report upon completion of each service call. A copy of the signed service report shall be left with the COR or designee official responsible for the GE CARESCAPE equipment. The Contractor shall also forward copies of the Installation, Programming, and Testing Service Reports to the COR by the 7th day after service is performed.

However, Emergency Maintenance Service Reports shall be forwarded to the COR within 10 working days after completion of the service. At a minimum, Service Reports should include the following:

6.1.1 Device type, Model Number, Serial Number, Location, Configuration/settings on device, Testing Results, and Technician Comments.

6.2 Original Equipment Manufacturer’s Supporting Documentation

6.2.1 The Contractor shall provide hard copies and digital copies of the latest versions of the manufacturer’s manuals for operation, maintenance, inspection, and repair.

6.3 Invoices: The Contractor shall submit an original invoice and three copies (or electronic invoice, if authorized) to the address designated in the contract to receive invoices. The invoice shall be emailed to the COR or his/her designee. An invoice must include the following:

6.3.1 Name and address of the Contractor;

6.3.2 Invoice date and number;

6.3.3 Contract number, line item number and, if applicable, the order number;

6.3.4 Description, quantity, unit of measure, unit price and extended price of the items delivered;

6.3.5 Shipping number and date of shipment, including the bill of lading number and weight of shipment if shipped on Government bill of lading;

6.3.6 Terms of any discount for prompt payment offered;

6.3.7 Name and address of official to whom payment is to be sent;

6.3.8 Name, title, and phone number of person to notify in event of defective invoice; and

6.3.9 Taxpayer Identification Number (TIN). The Contractor shall include its TIN on the invoice only if required elsewhere in this contract.

6.3.10 Electronic funds transfer (EFT) banking information.

6.3.11 The Contractor shall include EFT banking information on the invoice only if required elsewhere in this contract. If EFT banking information is not required to be on the invoice, in order for the invoice to be a proper invoice, the Contractor shall have submitted correct EFT banking information in accordance with the applicable solicitation provision, contract clause (e.g., 52.232-33, Payment by Electronic Funds Transfer— System for Award Management, or 52.232-34, Payment by Electronic Funds Transfer—Other Than System for Award Management), or applicable agency procedures. EFT banking information is not required if the Government waived the requirement to pay by EFT.

6.3.12 Invoices will be handled in accordance with the Prompt Payment Act (31 U.S.C. 3903) and Office of Management and Budget (OMB) prompt payment regulations at 5 CFR part 1315.

6.4 Training: The Contractor shall schedule and provide operator and in-service training with the Medical Departments. The in-service trainings shall be provided by the Contractor:

6.4.1 Provide operational and problem identification training to patient care providers on-site Hopi Health Care Center.

6.4.2 The Contractor shall provide eight (8) days of Patient Monitoring Clinical Applications Training to the HHCC healthcare providers

6.4.3 Training resources such as operator’s guides and quick reference sheets shall be provided in hard copies and digital copies.

7. Conformance standards

The Contractor shall install and service the GE Healthcare equipment covered by this contract in accordance with the following:

7.1 Original Equipment Manufacturer’s (OEM) specification requirements

7.2 National Association of Specialized Equipment Dealers (NASED) requirements

7.3 National Fire Protection Association (NFPA) 99 (2012 Edition), 101 (2012 Edition), 70E (2012 edition)

7.4 The Joint Commission Standard (EC.02.04.03)

7.5 Association for the Advancement of Medical Instrumentation (ANSI/AAMI EQ56:2013))

7.6 Occupational Health and Safety Association

7.7 Federal, Tribal, and local regulatory guidance and ordinances in regards to bio hazardous waste, disposal, and applications

8. Quality Assurance

The Government will monitor the Contractor’s performance under this contract and shall retain the right to perform unscheduled inspections, as it deems necessary. Furthermore, the Government retains all rights provided by the FAR (Federal Acquisition Regulations) clause entitled “Inspection of Services – Fixed Price” and any other inspection clause, which may be specified in the contract.

9. Safety Precautions/ Bio-Hazard Safety

All system, either mechanical or electrical that must be deactivated before servicing shall be rendered by whatever disconnect or shut-off means are provided. Each deactivated system shall be properly “tagged-out” to prevent accidental reactivation. The PAO Service Unit Bio-Medical Department will furnish “tag-out” procedures and tags. The Government shall be responsible for removing the contents of any equipment and ensuring it is biologically safe. If applicable, the Contractor shall notify the PAO Service Unit Bio-Medical Department and Safety Officer before removing any bio-hazardous material. If applicable, the Contractor is responsible for removing and disposing of all hazardous materials/sources.

10. Schedule and Notification, Government Responsibility

The COR or designee will ensure that the service personnel have government issued badges to gain access to the PAO Service Unit facility and any equipment or instrument to be serviced 48 hours prior to beginning services and upon completion.

Contractor shall comply with IHS visitation policy.

10.1 Before performing services the Contractor personnel shall report to the local Facilities Engineering or Biomedical Engineering Department and PAO Service Unit Biomedical Department at the beginning and end of their entire visitation at the facility, to sign-in and receive a facility “Guest” badge.

10.2 The Contractor shall report to the Facilities and/or Biomedical Department at the beginning of each visitation for a wellness screening prior to start of work due to COVID-19 response. The Contractor’s personnel shall comply with all visitation requirements prior to entering the facility.

10.3 The Contractor shall be authorized to park only in areas opened to the public.

10.4 The Contractor shall be allowed minimal use of government space to store supplies and/or equipment as required under this contract.

10.5 The Contractor shall be responsible for any repair or damage incurred to the building system as a result of contractor errors or poor workmanship.

11. Inspection and Acceptance Criteria, Government Responsibility

The COR will monitor the Contractor’s activities and accomplishments and will indicate acceptance or non-acceptance of the deliverable. The deliverables identified above will be inspected and either approved or, if they are not acceptable, rejected by the COR. Such inspections will occur within five workdays after the COR receives the deliverable.

The Contractor shall establish an inspection system covering the equipment stated in this Statement of Work. The Contractor shall maintain a history file on all installations, testing, programming, repairs, relocations and inspections conducted. The history file shall be the property of the Government and shall be maintained by the Contractor and turned over to the COR upon completion of the contract.

12. Location The Contractor shall deliver all equipment and services to the following location:

12.1 Hopi Health Care Center (HHCC)

Hwy 246 Mile Marker 388 Polacca, AZ 86042

13. GE Healthcare CARESCAPE Equipment and Services

The Contractor shall deliver and install all GE Healthcare CARESCAPE equipment and provide all services listed in the following table:

Equipment Description

GE Healthcare Item # Quantity

CARESCAPE B450 V3.1 CARESCAPE B450 V3.1 MBA 313 2095800-001 9

B450 FRAME WITHOUT WLAN 2094541-001 9

CARESCAPE B450 ESP V3.1

SOFTWARE

2094545-001 9

B450 NO RECORDER OPTION 2066522-001 9

B450 V3.1 ENGLISH US

LOCALIZATION

2095076-016 9

B450 ENGLISH US KEYBOARD SW

SETTING

2068494-005 9

B450 POWER FREQUENCY

SETTING 60HZ

2068494-017 9

BATTERY FLEX-3S2P 10.8V 18650

LI-ION SMBUS (B450

COMPATIBLE)

2062895-001 9

POWER CORD, USA/CANADA 8FT

ANGLE, GE PN 405535-007

2066381-001 9

B450 4ECP – EMERGENCY CARE

SOFTWARE PACKAGE

2064282-018 9

PARR – FULL ARRYTHMIA

LICENSE

2105824-018 9

PDM SUPPORT 2105824-018 9

INSTALLATION SERVICES 2083083-001 9

CARESCAPE B450 V3.1 CARESCAPE B450 V3.1 MBA 313 2095800-001 3

B450 FRAME WITH WLAN 2094541-001 3

CARESCAPE B450 ESP V3.1

SOFTWARE

2094545-001 3

B450 RECORDER OPTION 2066520-001 3

B450 V3.1 ENGLISH US

LOCALIZATION

2095076-016 3

B450 ENGLISH US KEYBOARD SW

SETTING

2068494-005 3

B450 POWER FREQUENCY

SETTING 60HZ

2068494-017 3

BATTERY FLEX-3S2P 10.8V 18650

LI-ION SMBUS (B450

COMPATIBLE)

2062895-001 3

POWER CORD, USA/CANADA 8FT

ANGLE, GE PN 405535-007

2066381-001 3

B450 4ECP – EMERGENCY CARE

SOFTWARE PACKAGE

2064282-018 3

PARR – FULL ARRYTHMIA

LICENSE

2105824-018 3

PDM SUPPORT 2105824-018 3

INSTALLATION CHARGE 2083083-001 3

CARESCAPE Monitor Options

M SERIES PIVOT ARM 16” 2022719-002 9

5 WHEEL ROLL STAND DASH

W/ADAPTER PLATE

900276-011 4

19-INCH WALL CHANNEL 411959-001 9

INSTALLATION SERVICES 2083083-001 1

Patient Data Module PATIENT DATA MODULE (PDM) 2042084-001 12

NELLCOR ASSEMBLY NO CE 2041390-066 12

NELLCOR ENGLISH LANGUAGE

NO CE

2041390-064 12

60 HZ 2041575-002 12

INVASIVE PRESSURES 2041575-003 12

BATTERY 2041575-003 12

NO BEDSIDE DOCK 2041390-044 12

INTERCONNECT CABLE FOR

NELLCOR OXIMAX 3 M/10FT

2021406-001 12

NELLCOR DURASENSOR, FINGER,

REUSABLE, OXIMAX, DS100A

407705-006 12

DINACLICK AIRHOSE, 12 FT(3.6M)

CARE HOSE W/ RECTANGLE

CONNECTOR TO ADULT 2T

DINACLICK – 20/PK (5 SM. ADULT,

10 ADULT, 5 LG ADULT)

2059303-002 12

SOFT-CUF ASSORTMENT KIT, 2T

DINACLICK -20/ PK (5 SM. ADULT,

10 ADULT, 5 LG ADULT)

2059303-001 12

ECG TRUNK CABLE, 3/5-LEAD,

AHA, 3.6 M/12FT

2106305-001 12

ECG LEADWIRE SET, 5-LEAD,

GRABBER, AHA, 74 CM/ 29 IN

2106391-001

INSTALLATION SERVICES 2083083-001 12

CARESCAPE Monitor Options

CARESCAPE RESPIRATORY

MODULE E-SCO, SINGLE WIDTH

MODULE WITH CO2 & O2

AIRWAY GAS MANAGEMENT

M119904 6

D-FEND PRO+ WATER TAP,

GREEN, SINGLE PATIENT USE,

(FOR CRITICAL CARE MODULES

E-SCO/E-SCOV)

M1200227 4

TEMPERATURE CABLE, 400

SERIES FOR DISPOSABLE

PROBES, SINGLE, 3.6 M/12FT

2104179-001 4

CSCS v2.x All-in-one CARESCAPE CENTRAL STATION

V2 MAI 700 ATO MODEL

2092670-001 1

NEW – CSCS V2.1 SW WITH

MAI700 INTEGRATED HW

2092695-005 1

CSCS V2.1 ENGLISH-US

LOCALIZATION WITH

EMANUALS

2092690-46 1

CSCS ENGLISH-US KEYBOARD

WITH MOUSE

2081739-004 1

NORTH AMERICAN, 6FT. 80274-006 1

BED VIEW LICENSE – 1 BED 2092862-001 12

MULTIKM LICENSE 2092863-004 1

PATIENT MANAGEMENT

LICENSES

2092863-001 1

ADT PICKLIST LICENSE 2092863-002 1

REVIEW LICENSES 2092864-001 1

FD PAGE AND REALTIME TRENDS

LICENSES

2092864-002 1

OXYCRG LICENSE 2092864-007 1

PDF TO EMR LICENSE 2092864-008 1

CSCS 24 HR FD LICENSE 2095336-001 12

CSCS V2 STRIP PRINTER

ACCESSORY KIT

2100519-001 1

INSITE CONNECTIVITY: ON-

DEMAND DIGITAL SERVICE

2025330-001 1

INSTALLATION SERVICES 2083083-001 1

CSCS v2.x All-in-one CARESCAPE CENTRAL STATION

V2 MAI 700 ATO MODEL

2092670-001 2

NEW – CSCS V2.1 SW WITH

MAI700 INTEGRATED HW

2092695-005 2

CSCS V2.1 ENGLISH-US

LOCALIZATION WITH

EMANUALS

2092690-46 2

CSCS ENGLISH-US KEYBOARD

WITH MOUSE

2081739-004 2

NORTH AMERICAN, 6FT. 80274-006 2

BED MIRROR LICENSE – 1 BED 2092862-002 24

MULTIKM LICENSE 2092863-004 2

PATIENT MANAGEMENT

LICENSES

2092863-001 2

ADT PICKLIST LICENSE 2092863-002 2

REVIEW LICENSES 2092864-001 2

FD PAGE AND REALTIME TRENDS

LICENSES

2092864-002 2

OXYCRG LICENSE 2092864-007 2

PDF TO EMR LICENSE 2092864-008 2

CIC LASER PRINTER 2039670-001 2

CSCS V2 STRIP PRINTER

ACCESSORY KIT

2100519-001 2

INSITE CONNECTIVITY: ON-

DEMAND DIGITAL SERVICE

2025330-001 2

INSTALLATION SERVICES 2083083-001 2

CSCS v2.x License Expansion

CSCS V2 EXPANSION – SERIAL

NUMBER REQUIRED FOR ALL

CENTRAL STATIONS

2099146-001 1

LICENSE EXPANSION KIT 2099139-001 1

BED VIEW LICENSE – 1 BED 2092862-001 3

CSCS 24 HR FD LICENSE 2095336-001 3

INSTALLATION SERVICES 2083083-001 1

CSCS v2.x All-in-one CARESCAPE CENTRAL STATION

V2 MAI 700 ATO MODEL

2092670-001 2

NEW – CSCS V2.1 SW WITH

MAI700 INTEGRATED HW

2092695-005 2

CSCS V2.1 ENGLISH-US

LOCALIZATION WITH

EMANUALS

2092690-46 2

CSCS ENGLISH-US KEYBOARD

WITH MOUSE

2081739-004 2

NORTH AMERICAN, 6FT. 80274-006 2

BED MIRROR LICENSE – 1 BED 2092862-002 18

MULTIKM LICENSE 2092863-004 2

PATIENT MANAGEMENT

LICENSES

2092863-001 2

ADT PICKLIST LICENSE 2092863-002 2

REVIEW LICENSES 2092864-001 2

FD PAGE AND REALTIME TRENDS

LICENSES

2092864-002 2

OXYCRG LICENSE 2092864-007 2

PDF TO EMR LICENSE 2092864-008 2

CSCS V2 STRIP PRINTER

ACCESSORY KIT

2100519-001 2

INSITE CONNECTIVITY: ON-

DEMAND DIGITAL SERVICE

2025330-001 2

INSTALLATION SERVICES 2083083-001 2

Configuration and Education Services

PATIENT MONITORING CLINICAL

APPLICATIONS TRAINING, 1 DAY

2016373-349 8

CARESCAPE Bx50

CONFIGURATION

2048581-001 1

Wireless Networking WLAN MONITOR WIRELESS

INTEGRATOR OPTION

WBED_WRL_INTR 1

WIRELESS CONSULATION AND

CONFIGUATION SUPPORT – PER

DEVICE

WBED-WRL-PD 4

CARESCAPE Network NETWORK DESIGN/CONSULT SEG NETWORK– 15+ Nodes

2036075-001 2

NETWORK DESIGN/CONSULT SEG

NETWORK- <15 nodes

2036075-034 14

NETWORK EQUIPMENT –

STANDARD (MINIMUM 7 NODES)

2036075-218 16

NETWORK EQUIPMENT – UPS

FOR SWITCHS/ROUTERS (PER 20

NODES)

2036075-011 1

NETWORK EQUIPMENT

INSTALLATION SERVICES

(MINIMUM 7 NODES)

2036075-021 16

NETWORK FIBER RUN INSTALL –

DUST CARTS

2036075-020 2

NETWORK DROP INSTALL

W/CAT6, DUST CARTS

2036075-020 16

CONFIGURATION SERVICES FOR

INTER-VLAN ROUTING FOR

CARESCAPE DEVICES

2036075-208 1

CARESCAPE NETWORKING

DOCUMENTATION KIT AND

LABELS

2036075-058 1

CARESCAPE Upgrades B450 UPGRADE KIT, RECORDER

UNIT

M1233543 1

UPGRADE KIT, WLAN, B450V3

SERIAL NUMBER REQUIRED

2110688-001 1

INSTALLTION SERVICES 2083083-001 1

SHIPPING/HANDLING SERVICES

FOR ALL CARESCAPE

EQUIPMENT

N/A 1