Statement of Work (SoW).pdf

Distribution Statement A: Distribution authorized Public Release; distribution is unlimited.

STATEMENT OF WORK

Procurement of

Radio Frequency Amplifier’s

For

AN/ALQ-184 Radio Frequency Amplifier’s and AN/ALQ-161 Radio Frequency Amplifier’s

Prepared by

Naval Surface Warfare Center

Crane, Indiana

Code WXPM

10/14/2025

TABLE OF CONTENTS

SECTION/PARAGRAPH PAGE

1. Scope 3

1.1. Component Part Number 3

2. Applicable Documents 3

2.1. Components Specifications 3

2.2. Components Other Documents 3

3. Requirements 3

3.1. Components Requirement 3

3.1.1. Equipment, Material, and Services 3

3.1.1.1. Construction, Performance and Physical Dimensions 4

3.1.2. Controlled Unclassified Information (CUI) Access 4

3.1.3. Classified Information 4

3.1.4. Dissemination of Classified Information 4

3.1.5. Operations Security (OPSEC) Requirements 4

4. Components Product Assurance Provisions 4

4.1. Quality Assurance Program 4

4.1.1. Program Management 4

4.1.2. Configuration Control 4

4.1.3. Contractor Data 4

4.1.4. Periodic Visits 5

4.2. Acceptance Test 5

4.2.1. Acceptance Test Report 5

4.2.2. Screening Requirement 5

5. Quantity and Delivery Requirements 5

5.1. Components Deliverable Data 5

5.2. Components Packaging and Marking 5

6. Points of Contact 6

1. SCOPE

This Statement of Work (SOW) defines the requirements for equipment, material, and services to be furnished to Naval Surface Warfare Center Crane (hereinafter referred to as “NSWC Crane”) by the recipient of a contract (hereinafter referred to as “Contractor”) for the production of two amplifier’s (P/N:

ALO/180-7536-11), two amplifier’s (P/N: APW/105-2218-269), three amplifier’s (P/N: APW/054-2427- 269), two amplifier’s (P/N: APW/052-2618-269), and seven amplifier’s (P/M: APW/055-3346-269). The components are intended to serve as a form, fit, and function replacement for the amplifier’s used in the AN/ALQ-184 and AN/ALQ-161 systems.

1.1. COMPONENTS PART NUMBERS

The Components will be referred by their specification number and will have a corresponding Contractor part number.

2. APPLICABLE DOCUMENTS

Unless otherwise specified herein, the following documents of latest issue shall form a part of this Statement of Work as if fully listed herein. The precedence of the documents is the order listed.

a) Contract

b) Statement of Work

c) Power Supply Salient Specification

d) Other standards, specifications, procedures, etc. referred in this Statement of Work

e) Contractor’s drawing, specifications, and facilities manual

2.1. COMPONENTS SPECIFICATIONS (vendor has specifications)

G275706 Amplifier, Microwave, GaAs FET 435420 Eaton, Amplifier, RF 435365 Eaton, Amplifier, RF 105005426 Outline, CTT APW-055-3346-269 CTT Model Number, Parameters

2.2. COMPONENTS OTHER DOCUMENTS

ISO 9003 Quality Systems – Model for Quality Assurance in Final Inspection and

Test

3. REQUIREMENTS

3.1. COMPONENTS REQUIRMENT

3.1.1. EQUIPMENT, MATERIALS, AND SERVICES

It is NSWC Crane’s intent to procure 16 components. The Contractor shall perform the work, render the services, and provide the data, facilities, personnel, materials, and supplies as necessary to manufacture, inspect, test, package, and deliver components in accordance with the contract. The listed components have previously completed certification testing however NSWC Crane reserves the right to perform certification testing on all components at its discretion to verify compliance. The certification testing is defined in paragraph 6.0.

3.1.1.1. CONSTRUCTION, PERFORMANCE AND PHYSICAL DIMENSIONS

The performance and physical dimensions of the components shall be as defined in the component specifications. The construction (materials, techniques, etc.) defined in the specifications may be changed provided the contractor receives written authorization from NSWC Crane to deviate from the specification requirements. NSWC Crane, at its discretion, may incorporate authorized changes into the specification for future procurements.

3.1.2. CONTROLLED UNCLASSIFIED INFORMATION (CUI) ACCESS

Performance under this contract will require the Contractor to have access to CUI (formerly “For Official Use Only” information), as well as to receive, store, or generate CUI.

3.1.3. CLASSIFIED INFORMATION

Performance under this contract will require the Contractor to receive, generate, and/or store classified information.

3.1.4. DISSEMINATION OF CLASSIFIED INFORMATION

Performance under this contract will require the Contractor to provide classified information to over contractors performing REAM tasking, as directed by the Technical Point of Contact cited in the DD 254.

3.1.5. OPERATIONS SECURITY (OPSEC) REQUIREMENTS

Performance under this Job Order shall require the Contractor to protect critical information in order to prevent unauthorized disclosure. Additionally, the Contractor shall observe OPSEC requirements.

4. COMPONENTS PRODUCT ASSURANCE PROVISIONS

4.1. QUALITY ASSURANCE PROGRAM

The Contractor shall establish and maintain a quality assurance program in accordance with ISO 9003 or similar quality assurance standard. The quality assurance program shall ensure quality control throughout all areas of contract performance. The quality assurance program shall be available for NSWC Crane review upon request

4.1.1. PROGRAM MANAGEMENT

The Contractor shall direct, manage, and monitor performance of the contract in order to satisfy contractual requirements, to assure that the production of all deliverable items is accomplished on schedule, and to resolve any problems or schedule delays.

4.1.2. CONFIGURATION CONTROL

The Contractor shall maintain a configuration control program throughout the duration of this contract.

The configuration baseline for each component is established when the component is deemed qualified based on certification testing. Once the configuration baseline is established, there shall be no component configuration changes made without NSWC Crane’s approval. The configuration documentation shall be available for NSWC Crane’s review at the Contractor’s facility.

4.1.3. CONTRACTOR DATA

The Contractor shall maintain copies of all production data, test data, failure investigations, and corrective actions at the contractor’s facility for NSWC Crane’s review.

4.1.4. PERIODIC VISITS

The Contractor shall make his facility available, at no additional cost, for periodic visits by NSWC Crane personnel.

4.2. ACCEPTANCE TEST

An acceptance test consisting of performance characteristics as specified in the specification G275706, 435420, 435365, and 89 TPA 99 3778 shall be performed on each component to verify the component meets the requirements of the component specification.

4.2.1. ACCEPTANCE TEST REPORT

A paper copy of the acceptance test data shall be provided with each component delivered and an electronic copy (pdf format) shall be provided to NSWC Crane’s engineering representative. (CDRL A001)

5. QUANTITY AND DELIVERY REQUIREMENTS

Quantities and delivery schedules of components shall be as delineated in the contract or delivery order.

5.1. COMPONENTS DELIVERABLE DATA

Data required per this Statement of Work shall be marked with the contract number and CDRL number.

CDRL: A001

DID Number: DI-NDTI-80809B DID Title: Test/Inspection Report Subtitle: Acceptance Test Report SOW Para: 4.2.1

5.2. COMPONENTS PACKAGING AND MARKING

Components and documentation shall be packaged and marked in accordance with good commercial practices, to protect against physical damage and insure its safe arrival at NSWC Crane’s facility.

6. POINTS OF CONTACT

Point of contact for technical issues of non-substantive nature for this contract is the Requiring Technical Agent (RTA), Kimberly Christenberry, 812-854-3326, email:

Kimberly.k.christenberry@us.navy.mil. All communications between prospective contractors and the Government shall flow through the contracting office until a contract is awarded.