Statement of Work_.pdf

Pan, Tilt, Zoom (PTZ) Integrated High Definition Range Camera Systems

Requirement Description and Details

1. General Description:

This contract will cover the purchase and delivery of (24) Pan and Tilt (MPT-50) integrated range camera systems capable of providing high definition imagery and remote control. The camera systems will directly support test ranges at Aberdeen Test Center (ATC).

2. Background:

ATC requires the purchase of (24) weather-resistant Pan and Tilt (MPT-50) integrated range camera systems capable of high-definition serial digital interface (HD-SDI), 30X optical zoom, 2- 59 degree viewing angle, and 180 degree elevation & 435 degree azimuth movement. This camera system is instrumental and required for documenting and analyzing unique RDT&E test events at ATC. To sustain high resolution imaging support for RDT&E testing and meet mission requirements, acquisition of the stated equipment is essential for the replacement of the ATC’s existing obsolete range camera infrastructure.

3. Requirement Description and Details:

camera system must have the following characteristics:

1. 1/2.8 type Exmor CMOS sensor, with minimum of 2.13 megapixels, HD-SDI output

2. Minimum of 30X optical zoom, with f=4.3 mm (wide) to 129 mm (tele), and 12X digital zoom

3. Lens aperture of F1.6 wide to F4.7 tele

4. Horizontal viewing angle in 1080p mode, 59.5 to 2.1 degrees

5. Pan and Tilt Positioner:

a. Payload rated load torque: 50 lbf-ft, payload capacity: up to 75 pounds

b. Maximum current draw of 4.5 amp peak, 3 amp continuous, 650 mAmp standby

c. 65 Watt heater power

d. Operating voltage range of 24VDC, 24-28 VDC

e. Minimum azimuth travel of 435 degrees, with speed from 0.005 to 50 degrees per second

f. Minimum elevation travel of 180 degree, +/- 90 degree from horizon, with speed from

0.005 to 12 degrees per second

g. Minimum incremental movement of 0.01 degrees

h. Both mechanical and software adjustable limit stops

i. Position feedback with 9000 line encoder resolution of 0.01 degrees with repeatability of 0.05 degrees. 1.8 degree stepper motor.

j. IP67 environmental rating, operating temperature without heater (-15C to 55C) with heater -30C to 55C

k. Powder coated finish, cast aluminum housing with stainless steel hardware

l. Integral web server. PTCR-1000, Pelco-D protocol

m. Velocity commands of 10-bit, linear response

n. Minimum monitoring of power on and run time, voltage, current, with real-time clock

o. Ability to interface with payload with Serial RS232, RS422, RS485 configurable communication, 4 ports; 2 TTL, 1 IP

p. Minimum (1) 53 conductor connector for positioner, and (2) 53 conductor connector for payload

q. Payload mounting surface size of 10 inches by 5 inches for replacement/additional cameras

r. Hardened steel worm drive gears

s. Controllable with a Unicom joystick

6. Power supply unit of 85-260 VAC input, 24VDC 10.2 amp output

7. Base STD 53S with flying leads cable

8. Unicom LT ruggedized controller joystick

9. 8 FT input AC outdoor power cable

10. 1 day operating training and phone technical support

1. Quantity (24), 2-JA-V0129H-000-MWS, Custom camera system with MPT-50 positioner

2. Quantity (24), 7-08964, PSU power supplies, IN: 85-260 VAC, OUT 24VDC 10.2A

3. Quantity (24), CC56545-25, Cable, Base STD 53S w/flying leads

4. Quantity (5), CLT-1000R, Ruggedized Unicom joystick controller

5. Quantity (24), 6-19235-8, Outdoor 8FT cable input AC

4. Delivery Details:

Vendor is responsible for shipping to the following

Place of delivery:

Aberdeen Test Center ATTN: Timothy Shylanski, Technical Imaging Division 6850 Lanyard Road, B-358 Aberdeen Proving Ground, MD 21005

Expected delivery is within 4 weeks after contract award