ENs-Hatches-19-00027.pdf

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9450FG 200945043-20 28 JULY, 2016

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

Available as a commercial product

AFLC FORM 2559 (COMPUTER GENERATED) PREVIOUS EDITION WILL BE USED

PAGE 1A

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9450FG 200945043-20 28 JULY, 2016

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-11)

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-11 SEAL ASSEMBLY AND ATTACHMENT

HARDWARE."

PART NUMBER NOMENCLATURE QTY

66D25643-11 SEAL ASSEMBLY 1

24-1101-41 CABLE TAB 4

24-1101-38 CABLE, SEAL RETAINER 1

24-1101-43 CABLE, SEAL RETAINER 1

3. FABRICATE 24-1101-83 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE 0.50

INCH +/- 0.05 INCH EXCESS AROUND ENTIRE PERIPHERY OF THE 24-1101-83 SKIN.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE

5. OMIT AERODYNAMIC SMOOTHER AROUND ENTIRE PERIPHERY OF LIFTER PAN (24-1884) REFERENCE

DRAWING 24-01884 FN 6.

6. OMIT FILLER MATERIAL FROM (2) 0.375 INCH DIAMETER PUSH ROD HOLES ON OUTSIDE OF LIFTER, REFERENCE DRAWING 24-01884 SHEET 2, VIEW 1B10 AND FLAG NOTE 6.

7. OMIT MARKINGS AS SHOWN IN DETAILS II & IV OF DRAWING 24-01101 SHEET 1.

8. OMIT FINISH AS SHOWN IN DETAIL IV OF DRAWING 24-01101 SHT 1.

9. OMIT EXTERIOR MARKINGS AS SHOWN ON DRAWING 29-10543.

10. NOTE DELETED 6 AUGUST 2013.

11. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

12. 200945043-20, IDENTIFY PER DRAWING 200945043 EO 2016A0053.

13. ALL SPECIAL PROCESSES IDENTIFIED BY 424 SCMS IN DRAWING 20145214 SHALL BE PERFORMED BY BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR THE RELEVANT SPECIAL PROCESS.

ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS

AS REQUIRING NADCAP CERTIFIED PROCESSORS.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9450FG 200945043-20 28 JULY, 2016

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

SERIALIZATION OF PARTS (CHECK WHEN APPLICABLE)

Serialization of each part/assembly (contract end item) is required.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9450FG 200945043-20 28 JULY, 2016

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room temperature prior to use.

B. Do not stretch or otherwise apply stress.

C. Check the dimensional accuracy of the grid lines. The dimension between adjacent grid lines must be within .005 inch. The grid lines shall be measured vertically, horizontally and diagonally, to insure that the grids are within a tolerance of .005 inch. The tolerance is accumulated over the length and width of the stable base drawing.

D. Trammel points shall be measured to within .010

E. When rolling stable base drawings, do not roll less than 3 inches in diameter.

F. If the above tolerance points prove to be inaccurate, record the discrepancies immediately and notify in writing. OC-ALC/PKXDA and the Administrative Contracting Officer (ACO)

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2807FG 200945045-10 23 OCT 2017

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2807FG 200945045-10 23 OCT 2017

FABRICATE FAIRING ASSEMBLY 24-1142-511 HATCH, COMPLETE PER ENGINEERING DRAWING EXCEPT THE

FOLLOWING:

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-15).

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-15 SEAL ASSEMBLY AND ATTACHMENT

HARDWARE."

PART NUMBER NOMENCLATURE QTY

66D25643-15 SEAL ASSEMBLY 1

24-1142-22 CABLE TAB 4

24-1142-23 CABLE, SEAL RETAINER 1

24-1142-24 CABLE, SEAL RETAINER 1

3. FABRICATE 24-1142-85 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE

0.50 INCH +/- 0.05 INCH EXCESS AROUND THE ENTIRE PERIPHERY 24-1142-85 SKIN ONLY.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE. FINISH F-12.37 ONLY EXCEPT AS SHOWN ON DRAWING 24-01142, SHEET 1, DETAIL V (NOTED AS F-2.10 THIS AREA). DELETE ALL OTHER FINISH, MARKING AND STENCIL REQUIREMENTS.

5. DO NOT APPLY AERODYNAMIC SMOOTHER PER FLAG NOTE 6 ARROUND THE ENTIRE PERIPHERY OF THE 24-1883 LIFTER PAN. REFERENCE DRAWING 25-12616 SHEET 1 AND 25-12428 SHEET 1. ALSO OMIT

AERODYNAMIC SMOOTHER FROM (2) 0.375 INCH DIAMETER PUSH ROD HOLES ON THE OUTSIDE OF LIFTER

AS NOTED BY 24-01883 FLAG NOTE 8, REFERENCE 24-01883 SHEET 2, VIEW 1B10.

6. OMIT MARKINGS AS SHOWN IN DETAILS I, II, & IV OF DRAWING 24-01142 SHEET 1.

7. OMIT EXTERIOR MARKING AS SHOWN ON DRAWING 29-10543.

8. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

9. 200945045-10, IDENTIFY PER DRAWING 200945045 EO 2016A0054.

FABRICATE FAIRING ASSEMBLY 35-30063-501 COMPLETE PER ENGINEERING DRAWING EXCEPT THE

FOLLOWING:

10. INSTALL 35-30063-7 DOOR COMPLETE.

11. 35-30064-509: INSTALL ALL FASTENERS (3) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-511 ANGLE.

12. 35-30064-511: INSTALL ALL FASTENERS (2) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-511 ANGLE.

13. 35-30063-511: INSTALL COMPLETE TO 35-30063-513 FRAME. INCLUDE #40 PILOT HOLES @ (5) 0.190 / 0.194 DIAMETER HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30064-509 (3) PLACES AND THE 35-30064-

511 (2)PLACES AS SHOWN ON DRAWINGS 35-29710 SHEET 2 & 35-30063 SHEET 3.

14. 35-30064-505: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-507 ANGLE.

15. 35-30064-507: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-507 ANGLE.

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2807FG 200945045-10 23 OCT 2017

16. 35-30064-501: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-505

ANGLE.

17. 35-30063-505: INSTALL COMPLETE TO 35-30063-503 FRAME. INCLUDE #30 PILOT HOLES @ (9) 0.250 / 0.254 DIAMETER HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-505 (5) PLACES AND THE 35-

30064-501 (4) PLACES AS SHOWN ON DRAWINGS 35-29710 SHEET 2 AND 35-30063 SHEET 3.

18. INCLUDE 0.50 INCH +/- 0.05 EXCESS ON FORWARD EDGE OF SKIN 35-30063-5.

19. PART MARK PER DRAWING 35-30063 EO 2011C0074.

20. FABRICATE / PURCHASE THE FOLLOWING FILLER AND HARDWARE COMPLETE PER ENGINEERING

DRAWING, INDIVIDUALLY PROTECTIVE WRAP AND COMBINE IN A SINGLE BAG:

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS 35-30065 FILLERS

35-30065-1 FILLER 1

35-30065-2 FILLER 1

35-30065-3 FILLER 1

35-30065-4 FILLER 1

35-30065-5 FILLER 1

35-30065-6 FILLER 1

35-30065-7 FILLER 1

35-30065-8 FILLER 1

35-30065-9 FILLER 1

35-30065-10 FILLER 1

35-30065-11 FILLER 1

35-30065-12 FILLER 1

35-30065-13 FILLER 1

35-30065-14 FILLER 1

35-30065-15 FILLER 1

35-30065-16 FILLER 1

35-30065-17 FILLER 1

35-30065-18 FILLER 1

35-30065-19 FILLER 4

35-30065-20 FILLER 4

35-30065-21 FILLER 4

35-30065-22 FILLER 2

35-30065-23 FILLER 2

35-30065-24 FILLER 2

21. INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AND IDENTIFY THE FOLLOWING AS “FAIRING ATTACHMENT

FASTENERS 35-30063, SHEET 3, VIEW 1C5 “.

NAS6604-5 BOLT 17 REF. DWG 35-30063 EO2009C0042

NAS1149D0463K WASHER 17

MS21042L4 NUT 17

22. INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AND IDENTIFY THE FOLLOWING AS “FAIRING ATTACHMENT

FASTENERS 35-30063,SHEET 3, VIEW 2B9 & VIEW 1C2”.

NAS6603-5 BOLT 5 REF. DWG 35-30063 EO2009C0042

NAS1149D0363K WASHER 5

MS21042L3 NUT 5

23. ALL SPECIAL PROCESSES IDENTIFIED BY 424 SCMS IN DRAWING 20145214 SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR THE RELEVANT SPECIAL PROCESS. ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS AS REQUIRING

NADCAP CERTIFIED PROCESSORS

AFLC FORM 2559 (COMPUTER GENERATED) PREVIOUS EDITION WILL BE USED

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2807FG 200945045-10 23 OCT 2017

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

� Serialization of each part/assembly (contract end item) is required.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2807FG 200945045-10 23 OCT 2017

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room temperature prior to use.

B. Do not stretch or otherwise apply stress.

C. Check the dimensional accuracy of the grid lines. The dimension between adjacent grid lines must be within .005 inch. The grid lines shall be measured vertically, horizontally and diagonally, to insure that the grids are within a tolerance of .005 inch. The tolerance is accumulated over the length and width of the stable base drawing.

D. Trammel points shall be measured to within .010

E. When rolling stable base drawings, do not roll less than 3 inches in diameter.

F. If the above tolerance points prove to be inaccurate, record the discrepancies immediately and notify in

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2808FG 200945045-20 23 OCT 2017

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2808FG 200945045-20 23 OCT 2017

FABRICATE FAIRING ASSEMBLY 24-1142-512 HATCH, COMPLETE PER ENGINEERING DRAWING EXCEPT THE

FOLLOWING:

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-15).

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-15 SEAL ASSEMBLY AND ATTACHMENT

66D25643-15 SEAL ASSEMBLY 1

24-1142-22 CABLE TAB 4

24-1142-23 CABLE, SEAL RETAINER 1

24-1142-24 CABLE, SEAL RETAINER 1

3. FABRICATE 24-1142-86 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE

0.50 INCH +/- 0.05 INCH EXCESS AROUND THE ENTIRE PERIPHERY 24-1142-86 SKIN ONLY.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE. FINISH F-12.37 ONLY EXCEPT AS SHOWN ON DRAWING 24-01142, SHEET 1, DETAIL V (NOTED AS F-2.10 THIS AREA). DELETE ALL OTHER FINISH, MARKING AND STENCIL REQUIREMENTS.

5. DO NOT APPLY AERODYNAMIC SMOOTHER PER FLAG NOTE 6 ARROUND THE ENTIRE PERIPHERY OF THE 24-1883 LIFTER PAN. REFERENCE DRAWING 25-12616 SHEET 1 AND 25-12428 SHEET 1. ALSO OMIT AERODYNAMIC SMOOTHER FROM (2) 0.375 INCH DIAMETER PUSH ROD HOLES ON THE OUTSIDE OF LIFTER

AS NOTED BY 24-01883 FLAG NOTE 8, REFERENCE 24-01883 SHEET 2, VIEW 1B10.

6. OMIT MARKINGS AS SHOWN IN DETAILS I, II, & IV OF DRAWING 24-01142 SHEET 1.

7. OMIT EXTERIOR MARKING AS SHOWN ON DRAWING 29-10543.

8. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

9. 200945045-20, IDENTIFY PER DRAWING 200945045 EO 2016A0054.

FABRICATE FAIRING ASSEMBLY 35-30063-502 COMPLETE PER ENGINEERING DRAWING EXCEPT THE

FOLLOWING:

10. INSTALL 35-30063-8 DOOR COMPLETE.

11. 35-30064-510: INSTALL ALL FASTENERS (3) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-512 ANGLE.

12. 35-30064-511: INSTALL ALL FASTENERS (2) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-512 ANGLE.

13. 35-30063-512: INSTALL COMPLETE TO 35-30063-514 FRAME. INCLUDE #40 PILOT HOLES @ (5) 0.190 / 0.194 DIAMETER HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30064-509 (3) PLACES AND THE 35-30064-

512 (2)PLACES AS SHOWN ON DRAWINGS 35-29710 SHEET 2 & 35-30063 SHEET 3.

14. 35-30064-506: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-508 ANGLE.

15. 35-30064-508: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-508 ANGLE.

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2808FG 200945045-20 23 OCT 2017

16. 35-30064-502: INSTALL ALL FASTENERS (4) COMPLETE THAT ARE COMMON TO THE LIFTER PER DRAWING 35-29710 SHEET 2. OMIT ALL HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-506

ANGLE.

17. 35-30063-506: INSTALL COMPLETE TO 35-30063-504 FRAME. INCLUDE #30 PILOT HOLES @ (9) 0.250 / 0.254 DIAMETER HOLES IN HORIZONTAL FLANGE COMMON TO THE 35-30063-506 (5) PLACES AND THE 35-

30064-502 (4) PLACES AS SHOWN ON DRAWINGS 35-29710 SHEET 2 AND 35-30063 SHEET 3.

18. INCLUDE 0.50 INCH +/- 0.05 EXCESS ON FORWARD EDGE OF SKIN 35-30063-6.

19. PART MARK PER DRAWING 35-30063 EO 2011C0074.

20. FABRICATE / PURCHASE THE FOLLOWING FILLER AND HARDWARE COMPLETE PER ENGINEERING

DRAWING, INDIVIDUALLY PROTECTIVE WRAP AND COMBINE IN A SINGLE BAG:

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS 35-30065 FILLERS

35-30065-1 FILLER 1

35-30065-2 FILLER 1

35-30065-3 FILLER 1

35-30065-4 FILLER 1

35-30065-5 FILLER 1

35-30065-6 FILLER 1

35-30065-7 FILLER 1

35-30065-8 FILLER 1

35-30065-9 FILLER 1

35-30065-10 FILLER 1

35-30065-11 FILLER 1

35-30065-12 FILLER 1

35-30065-13 FILLER 1

35-30065-14 FILLER 1

35-30065-15 FILLER 1

35-30065-16 FILLER 1

35-30065-17 FILLER 1

35-30065-18 FILLER 1

35-30065-19 FILLER 4

35-30065-20 FILLER 4

35-30065-21 FILLER 4

35-30065-22 FILLER 2

35-30065-23 FILLER 2

35-30065-24 FILLER 2

21. INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AND IDENTIFY THE FOLLOWING AS “FAIRING ATTACHMENT

FASTENERS 35-30063, SHEET 3, VIEW 1C5 “.

NAS6604-5 BOLT 17 REF. DWG 35-30063 EO2009C0042

NAS1149D0463K WASHER 17

MS21042L4 NUT 17

22. INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AND IDENTIFY THE FOLLOWING AS “FAIRING ATTACHMENT

FASTENERS 35-30063,SHEET 3, VIEW 2B9 & VIEW 1C2”.

NAS6603-5 BOLT 5 REF. DWG 35-30063 EO2009C0042

NAS1149D0363K WASHER 5

MS21042L3 NUT 5

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2808FG 200945045-20 23 OCT 2017

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

SERIALIZATION OF PARTS (CHECK WHEN APPLICABLE)

� Serialization of each part/assembly (contract end item) is required.

OF 5 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-585-2808FG 200945045-20 23 OCT 2017

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room temperature prior to use.

B. Do not stretch or otherwise apply stress.

C. Check the dimensional accuracy of the grid lines. The dimension between adjacent grid lines must be within .005 inch. The grid lines shall be measured vertically, horizontally and diagonally, to insure that the grids are within a tolerance of .005 inch. The tolerance is accumulated over the length and width of the stable base drawing.

D. Trammel points shall be measured to within .010

E. When rolling stable base drawings, do not roll less than 3 inches in diameter.

F. If the above tolerance points prove to be inaccurate, record the discrepancies immediately and notify in

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7124FG 200945046-10 23 OCT 2017

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7124FG 200945046-10 23 OCT 2017

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-7)

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-7 SEAL ASSEMBLY AND ATTACHMENT

66D25643-7 SEAL ASSEMBLY 1

04-03929-50 CABLE TAB 4

04-03929-48 CABLE, SEAL RETAINER 1

04-03929-164 CABLE, SEAL RETAINER 2

3. FABRICATE 4-3929-189 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE 0.50

INCH +/- 0.05 INCH EXCESS AROUND ENTIRE PERIPHERY OF THE 4-3929-189 SKIN.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE.

5. OMIT MARKINGS AS SHOWN ON DRAWING 04-03929 SHEET 1 DETAILS I, V & VI.

6. OMIT EXTERIOR MARKINGS PER DRAWING 25-10777 SHEET 1.

7. 10-1657-19, IDENTIFY PER DRAWING 10-1657 EO 2010C0010.

8. 200945046-10, IDENTIFY PER DRAWING 200945046EO 2016A0052.

9. FABRICATE AND INSTALL ALL COMPONENTS COMPLETE PER KIT INSTALLATION 35-30095-1 EXCEPT: DO

NOT PROCURE OR INSTALL THE 10-30470-2 AND 10-30470-3.

10. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

11. ALL SPECIAL PROCESSES IDENTIFIED BY 424 SCMS IN DRAWING 20145214 SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR THE RELEVANT SPECIAL PROCESS. ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS AS

REQUIRING NADCAP CERTIFIED PROCESSORS.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7124FG 200945046-10 23 OCT 2017

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7124FG 200945046-10 23 OCT 2017

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room temperature prior to use.

B. Do not stretch or otherwise apply stress.

C. Check the dimensional accuracy of the grid lines. The dimension between adjacent grid lines must be within .005 inch. The grid lines shall be measured vertically, horizontally and diagonally, to insure that the grids are within a tolerance of .005 inch. The tolerance is accumulated over the length and width of the stable base drawing.

D. Trammel points shall be measured to within .010

E. When rolling stable base drawings, do not roll less than 3 inches in diameter.

F. If the above tolerance points prove to be inaccurate, record the discrepancies immediately and notify in

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7128FG 200945046-20 23 OCT 2017

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7128FG 200945046-20 23 OCT 2017

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-7)

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-7 SEAL ASSEMBLY AND ATTACHMENT

66D25643-7 SEAL ASSEMBLY 1

04-03929-50 CABLE TAB 4

04-03929-48 CABLE, SEAL RETAINER 1

04-03929-164 CABLE, SEAL RETAINER 2

3. FABRICATE 4-3929-190 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE 0.50

INCH +/- 0.05 INCH EXCESS AROUND ENTIRE PERIPHERY OF THE 4-3929-190 SKIN.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE.

5. OMIT MARKINGS AS SHOWN ON DRAWING 04-03929 SHEET 1 DETAILS I, V & VI.

6. OMIT EXTERIOR MARKINGS PER DRAWING 25-10777 SHEET 1.

7. 10-1657-19, IDENTIFY PER DRAWING 10-1657 EO 2010C0010.

8. 200945046-20, IDENTIFY PER DRAWING 200945046 EO 2016A0052.

9. FABRICATE AND INSTALL ALL COMPONENTS COMPLETE PER KIT INSTALLATION 35-30095-1 EXCEPT: DO

NOT PROCURE OR INSTALL THE 10-30470-2 AND 10-30470-3.

10. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

11. ALL SPECIAL PROCESSES IDENTIFIED BY 424 SCMS IN DRAWING 20145214 SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR THE RELEVANT SPECIAL PROCESS. ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS AS

REQUIRING NADCAP CERTIFIED PROCESSORS.

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7128FG 200945046-20 23 OCT 2017

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

SERIALIZATION OF PARTS (CHECK WHEN APPLICABLE)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-7128FG 200945046-20 23 OCT 2017

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room temperature prior to use.

B. Do not stretch or otherwise apply stress.

C. Check the dimensional accuracy of the grid lines. The dimension between adjacent grid lines must be within .005 inch. The grid lines shall be measured vertically, horizontally and diagonally, to insure that the grids are within a tolerance of .005 inch. The tolerance is accumulated over the length and width of the stable base drawing.

D. Trammel points shall be measured to within .010

E. When rolling stable base drawings, do not roll less than 3 inches in diameter.

F. If the above tolerance points prove to be inaccurate, record the discrepancies immediately and notify in

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9446FG 200945043-10 03 AUG, 2016

1. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS APPLICABLE TO THIS

PRODUCT ARE OR HAVE:

(A) ENGINEERING CRITICAL IN APPLICATION: An item, which requires special manufacturing processes, controls, and testing of material or end items. Because of its use or application, failure to maintain the highest reliability of such an item could be catastrophic resulting in loss of life or serious injury, loss of a weapon system or extensive secondary damage, with direct impact on the capability to respond to a national emergency or to achieve wartime sustainability.

(B) CRITICAL CHARACTERISTICS: Characteristics which, when defective, are likely to result in hazardous or unsafe conditions for individuals using, maintaining or depending upon the product; or, are likely to prevent performance of the tactical function of a major end item such as an aircraft, missile, space vehicle, engine or a major part thereof. (Derived from MIL-STD-1916)

(C) MAJOR CHARACTERISTICS: Characteristics (other than critical or minor) which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916)

(D) MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.

(E) COMPLEX: Items having quality characteristics not wholly visible (hidden characteristics), in the end product for which contractual conformance must be established progressively through precise measurements, tests or controls applied during purchasing, manufacturing, performance, assembly and functional operation either as an individual item or in conjunction with other items [FAR SUBPART 46.203(b)].

(F) COMMERCIAL: Described in commercial catalogs, drawings or industrial standards [FAR SUBPART 46.203(a), (1)].

THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):

Engineering critical in application

Critical characteristics

Major characteristics

Minor characteristics, all excepting critical and major

Complex

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9446FG 200945043-10 03 AUG, 2016

2. DIRECTION TO LOOSE ATTACH SEAL ASSEMBLY AS FOLLOWS:

FABRICATE CHECK FIT AND LOOSE ATTACH THE SEAL ASSEMBLY (66D25643-11)

INDIVIDUALLY BAG AND TAG, IDENTIFY BAG AS "66D25643-11 SEAL ASSEMBLY AND ATTACHMENT

HARDWARE."

PART NUMBER NOMENCLATURE QTY

66D25643-11 SEAL ASSEMBLY 1

24-1101-41 CABLE TAB 4

24-1101-38 CABLE, SEAL RETAINER 1

24-1101-43 CABLE, SEAL RETAINER 1

3. FABRICATE 24-1101-83 SKIN COMPLETE PER ENGINEERING DRAWING REQUIREMENTS EXCEPT LEAVE 0.50

INCH +/- 0.05 INCH EXCESS AROUND ENTIRE PERIPHERY OF THE 24-1101-83 SKIN.

4. OMIT TOP COAT F-12.6589-36251 FROM EXTERIOR SURFACE.

5. OMIT AERODYNAMIC SMOOTHER AROUND ENTIRE PERIPHERY OF LIFTER PAN (24-1884) REFERENCE

DRAWING 24-01884 FN 6.

6. OMIT FILLER MATERIAL FROM (2) 0.375 INCH DIAMETER PUSH ROD HOLES ON OUTSIDE OF LIFTER, REFERENCE DRAWING 24-01884 SHEET 2, VIEW 1B10 AND FLAG NOTE 6.

7. OMIT MARKINGS AS SHOWN IN DETAILS II & IV OF DRAWING 24-01101 SHEET 1.

8. OMIT FINISH AS SHOWN IN DETAIL IV OF DRAWING 24-01101 SHT 1.

9. OMIT EXTERIOR MARKINGS AS SHOWN ON DRAWING 29-10543.

10. NOTE DELETED 6 AUGUST 2013.

11. 9-38926-2, IDENTIFY PER DRAWING 09-38926 EO 2010C0591.

12. 200945043-10, IDENTIFY PER DRAWING 200945043 EO2016A0053

13. ALL SPECIAL PROCESSES IDENTIFIED BY 424 SCMS IN DRAWING 20145214 SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR THE RELEVANT SPECIAL PROCESS. ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS AS

REQUIRING NADCAP CERTIFIED PROCESSORS

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9446FG 200945043-10 03 AUG, 2016

When materials, processes or components are to be obtained from directed sources as indicated herein or in the specifications, alternate sources may only be utilized upon prior approval by the contracting officer of this procuring activity as a deviation.

Bidders shall notify this procuring activity at the time of quotation of any drawing, specification or standard which is of more current data revision than those shown on the data listing or in these engineering notes.

Determination of acceptability of the more currently dated data will be made by the responsible engineering office of this procuring activity.

Lower tier specifications listed in or referenced by first tier specifications may not be shown on the data lists or engineering notes accompanying this contract but are nonetheless required by this contract for compliance.

Exceptions would occur only when such lower tier requirements have been specifically waived or substitute specifications/requirements are designated herein.

Reports, process sheets, inspection methods sheets and all other documents required by specifications imposed by this contract for contractor compliance which were previously required to be submitted to a prime design contractor shall be held at that facility for review by government personnel.

When prime design source specifications require or provide for participation by that prime source quality, manufacturing, laboratory or engineering support services, these requirements or provisions do not apply when the contract was issued by this procuring activity. For these services or direction pertaining thereto, contact the government contract administration office or this procuring activity for assistance.

The contractor is responsible for assuring that all dimensions, conditions, tests and test results identified in these engineering notes, applicable drawings, specifications and contract quality requirements are met by themselves and their suppliers. This requirement applies to all characteristics whether those characteristics have been specifically designed as being critical, major or are those minor characteristics not specifically designated as such.

PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)

Prior to beginning of manufacture, the contractor will notify the engineering office of this procuring activity of all manufacturing process and processing procedures intended for use in production of this product.

Once these processes are established, no changes shall be made without prior approval of the engineering office of this procuring activity.

TECHNICAL DATA PACKAGE - ENGINEERING NOTES (ENs)

OF 3 PAGES

NATIONAL STOCK NUMBER PART NUMBER DATE

1560-01-584-9446FG 200945043-10 03 AUG, 2016

STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)

When the use of stable base drawings is required, the following shall apply:

A. Stabilize by allowing the stable base drawing to rest flat and unrestrained on a flat surface overnight at room…