imageidx-20250520111726.pdf

02/09

02/09

A 1. UPDATED NOTE 2 9/28/09 FCL

ZONE REV DESCRIPTION

REVISIONS

DATE APPROVED

IG 02/09

FCL 02/09

15930 C

CONTAINER

NAMEPLATE

CAGE

CODE

QTY

REQ'D

PART NO.

IDENTIFY NUMBER

DATA: SPECIFICATION

NOTES, VENDORSNO.

ITEM

LENGTH

OD/ID

WIDTH

GAUGE

THICK

MATERIAL

NOMENCLATURE

OR DESCRIPTION

PARTS LIST

OF1

2/12/09

ARE IN INCHES

SPECIFIED DIMS

UNLESS OTHERWISE

USED ON

APPLICATION

NEXT ASSEMBLY

REVSIZE

DATE

DATE

DATE

DATEAPPROVED BY

QC APPROVED BY

CHECKED BY

DRAWN BY

DATE:

CONTRACT NUMBER

SHEET:WEIGHT:SCALE:

CAGE CODE DWG NO.

PHILADELPHIA,PA700 ROBBINS AVE.

NAVAL INVENTORY CONTROL POINT

B 80132

TOLERANCES ON:

.01 - .03RBREAK EDGES:

-.001 +.007

±.010 ±.015

HOLE SIZES:

BEND R .00 TO .09:

.091 AND ABOVE:

FRACTIONS: 1/16

ANGLES: 2°

DECIMALS:

.XX

.XXX

.X ±

.1

.06

.015

JVD

RWC

B 1. REVISED NOTE 5, ADDED NOTE 8 10/30/09 FCL

C 1. DESIGN P/N WAS MFR P/N 4/10/17 FCL

2. MFR/CAGE WAS MFR

1 15930 NAMEPLATE NOTE 2 .012 4.00 4.00

CAD MAINTAINED, CHANGES SHALL BE INCORPORATED BY THE DESIGN ACTIVITY.

NOTES:

1. CHARACTERS TO BE GOTHIC BOLD. LOCATE TEXT APPROXIMATELY AS SHOWN. TEXT

SIZE TO BE APPROXIMATELY AS SHOWN.

2. MATERIAL: .012 (.03MM) MINIMUM THICKNESS, PHOTOSENSITIVE, ANODIZED

ALUMINUM PLATE, HIGH STRENGTH ADHESIVE BACKED. RIVETS WILL BE USED TO

SECURE THE NAMEPLATE AND WILL BE SEALED ACCORDINGLY IF THE PRESSURE

BOUNDARY IS PENETRATED.

3. CHARACTERS AND DATA MATRIX TO BE BLACK ON A NATURAL BACKGROUND.

4. REFERENCE SPECIFICATION MIL-DTL-15024, TYPE H, STYLE IV.

5. CONTACT NAVSUP CODE N241.10 FOR ASSIGNMENT OF SERIAL NUMBER(S).

6. DATA MATRIX ECC 200 SYMBOL USING ISO 15434 SYNTAX AND THE SEMANTICS OF ISO

15418. SUBSTITUTE “R

S” SYMBOL WITH ASCII CODE 30, “G

S” SYMBOL WITH ASCII CODE

29, AND “E

OT” WITH ASCII CODE 4. EXACT CONTENTS OF MATRIX TO BE THE

FOLLOWING, ALL AS ONE CONTINUOUS STRING, WITHOUT SPACES:

[)>R

S06G S17V(vendor cage)G

S1P(container p/n)G SS [(program acronym)-SERIAL NO.]R

S E

OT

EXAMPLE, FOR SERIAL NUMBER 0001:

[)>R

S06G S17V80132G

S1P779E001-1G

SSARS-0001R

S E

OT

7. FOR REFERNCE ONLY: INFORMATION IS BASED ON UII CONSTRUCT #2: CAGE CODE,

ORIGINAL PART NO., SERIAL NO., AND DATA IDENTIFIERS (FORMAT 06).

8. ANY VARIATION TO THE NAMEPLATE (I.E. SIZE, MOUNTING HOLE DIMENSION AND

LOCATION, OR NOMENCLATURE) SHALL BE APPROVED BY NAVICP.

O .2194X

4.00

4.00

.192X

3.622X

.192X 3.622X

.012 MIN.

NOTES 5 & 6

NOTE 5

R .194X

.1511X

"Distribution Statement D: Distribution authorized to the Department of Defense and U.S. DoD contractors only, vulnerability information, 11

October 2012, other requests shall be referred to Commanding Officer Naval Supply Weapon Systems Support Philadelphia Pennsylvania 19111

(Attn Code N241.10)"

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et seq.)

or the Export Administration Act of 1979 (Title 50, U.S.C., App. 2401 et seq.) as amended. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

Destruction Note - Destroy by any method that will prevent disclosure of contents or reconstruction of the document.

DEPARTMENT OF THE NAVY

NAVSUP WEAPON SYSTEMS SUPPORT

CODE P0771 PACKAGING ENGINEERING TEAM

BUILDING 1, ROOM 2500

700 ROBBINS AVENUE

PHILADELPHIA PA 19111-5098

ENGINEERING CHANGE ORDER 1. ECO NO.:

2. DRAWING/PART NO.: 3. PART NOMENCLATURE: 4. REVISION:

5. CONTAINER NSN: 6. CONTAINER NOMENCLATURE: 7. DATE:

8. NEXT HIGHER ASSEMBLY: 9. REQUESTED BY:

10. DESCRIPTION OF CHANGE (WAS/IS):

11. REASON FOR CHANGE [INCLUDE JUSTIFICATION AND BACKUP DATA (IF AVAILABLE)]:

VALUE ENGINEERING SPEC CHANGE CORRECTIONS IN-SERVICE SAFETY NEW DRAWING

12. COMMENTS:

13. ECO ORIGINATOR SIGNATURE: 14. DATE:

15. ENGINEERING CHECK SIGNATURE: 16. DATE:

Cut two neoprene pads to the dimensions 23.50" x 3" x 0.125". For each pad, punch three holes 0.56" in diameter, spaced 7.5" apart, center-to-center. The hole pattern must precisely match the existing hole pattern on Item 10 (support beam). Bond a neoprene pad to each support beam (Item 10) using a suitable contact adhesive, ensuring precise alignment of the pad and beam holes.