SPRPA1-26-R-YB46.PDF

CAUTION TO OFFERORS - NO CONTRACT WILL BE AWARDED UNDER

THIS SOLICITATION AT GREATER THAN FAIR AND REASONABLE PRICES.

SECTION A - COVER SHEET

(See Section L of the Table of Contents in

You are cautioned to note the "Certification of Non-Segregated Facilities" in the solicitation. Failure to agree to the certification will render your reply nonresponsive to the terms of solicitations involving awards of contracts exceeding $25,000 which are not exempt from the provisions of the Equal Opportunity clause.

"Fill-ins" are provided on the face and reverse of Standard Form 18 and Parts I and IV of Standard Form 33, or other solicitation documents and Sections of Table of Contents in this solicitation and should be examined for applicability.

See the provision of this solicitation entitled "Late Bids, Modifications of Bids or Withdrawal of Bids" or "Late Proposals, Modifications of Proposals and Withdrawals of Proposals."

When submitting your reply,the envelope used must be plainly marked with the Solicitation Number, as shown above and the date and local time set forth for bid opening or receipt of proposals in the solicitation document.

If NO RESPONSE is to be submitted, detach this sheet from the solicitation, complete the information requested on reverse,fold, affix postage, and mail. NO ENVELOPE IS NECESSARY.

Replies must set forth full, accurate, and complete information as required by this solicitation The penalty for making false statements is prescribed in 18 U.S.C.1001.

(X one).

a. SEALED BID

c. NEGOTIATED (RFQ)

INSTRUCTIONS

NOTE THE AFFIRMATIVE ACTION REQUIREMENT OF THE EQUAL OPPORTUNITY CLAUSE WHICH MAY APPLY TO THE CONTRACT

RESULTING FROM THIS SOLICITATION.

3. ISSUING OFFICE

(including attachments).

4. ITEMS TO BE PURCHASED

5 PROCUREMENT INFORMATION

a. THIS PROCUREMENT IS UNRESTRICTED

b. THIS PROCUREMENT IS A ______% SET-ASIDE FOR ONE OF THE FOLLOWING

1. SOLICITATION NUMBER

INFORMATION TO OFFERORS OR QUOTERS

6. ADDITIONAL INFORMATION

(1) Small Business (2) Labor Surplus Area Concerns (3) Combined Small Business/Labor Area Concerns

DD Form 1707, MAR 89 Previous editions are obsolete.

(Brief description)

(Complete mailing address, including Zip Code)

(X one) this solicitation for details of the set-aside.)

(X and complete as applicable)

461/089

2.

b. NEGOTIATED (RFP)

7. POINT OF CONTACT FOR INFORMATION

a. NAME (Last, First, Middle Initial) b. ADDRESS (Include Zip Code)

c. TELEPHONE NUMBER (Include Area Code and Extension) (NO COLLECT CALLS)

SPRPA1-26-R-YB46

X 26042-0006

DLA AVIATION AT PHILADELPHIA, PA

DLR PROCUREMENT OPERATIONS (AP)

700 ROBBINS AVENUE BUILDING 26

PHILADELPHIA PA 19111-5098

SEE SCHEDULE

* THIS PROCUREMENT IS SET-ASIDE FOR SMALL BUSINESSES

K. LAUBER APBB.22

DLA AVIATION AT PHILADELPHIA, PA

(213) 737-3962 PHILADELPHIA PA 19111-5098

KKKKKKKKKKKKKKKKKKKJ

KKKKKKKKKKKKKKKKKKKJ

e. OTHER

8. REASONS FOR NO RESPONSE

DD Form 1707 Reverse, MAR 89

(1) Typed or Printed Name

d. DO NOT REGULARLY MANUFACTURE OR SELL THE TYPE OF ITEMS INVOLVED

b. CANNOT MEET DELIVERY REQUIREMENT

c. UNABLE TO IDENTIFY THE ITEM(S)

a. CANNOT COMPLY WITH SPECIFICATIONS

9. MAILING LIST INFORMATION

WE DESIRE TO BE RETAINED ON THE MAILING LIST FOR FUTURE PROCUREMENT OF THE TYPE OF ITEM(S) INVOLVEDYES NO

10. RESPONDING FIRM

a. COMPANY NAME b. ADDRESS

c. ACTION OFFICER

(4) Date Signed

AFFIX

STAMP

HERE

(X all that apply)

FROM

DATE (YYMMDD)

SOLICITATION NUMBER

LOCAL TIME TO

(Last, First, Middle Initial) (YYMMDD)

(2) Title (3) Signature

FOLDFOLD

FOLD FOLD

(Specify)

(X one)

(INCLUDE ZIP CODE)

SPRPA1-26-R-YB46

2026 MAY 26 02:00 P.M.

or if handcarried, in the depository located in until local time (Date)

9. Sealed offers in original and copies for furnishing the supplies or services in the Schedule will be received at the place specified in Item 8, IV

III

III

INSTRS., CONDS., AND NOTICES TO OFFERORS

21. ACCOUNTING AND APPROPRIATION20. AMOUNT19. ACCEPTED AS TO ITEMS NUMBERED

SOLICITATION

M

M

M

Prescribed by GSA FAR (48 CFR) 53.214(c)

EVALUATION FACTORS FOR AWARD

REPRESENTATIONS, CERTIFICATIONS AND

OTHER STATEMENTS OF OFFERORS

LIST OF ATTACHMENTS

CONTRACT CLAUSES

M L

K

J

I

SEC. DESCRIPTION PAGE(S)

SPECIAL CONTRACT REQUIREMENTS

CONTRACT ADMINISTRATION DATA

DELIVERIES OR PERFORMANCE

INSPECTION AND ACCEPTANCE

H G F E D C B A

PACKAGING AND MARKING

DESCRIPTION/SPECS./WORK STATEMENT

SUPPLIES OR SERVICES AND PRICES/COSTS

SOLICITATION/CONTRACT FORM

14. ACKNOWLEDGMENT OF AMENDMENTS

opposite each item, delivered at the designated point(s), within the time specified in the schedule.

from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set

(60 calendar days unless a different12. In compliance with the above, the undersigned agrees, if this offer is accepted within ______ calendar days

CODE

(Signature of Contracting Officer)

10. FOR INFORMATION

CALL:

(Type or print)

11. TABLE OF CONTENTS

33-132

(If other than Item 7)24. ADMINISTERED BY

CODE

STANDARD FORM 33

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

25. PAYMENT WILL BE MADE BY

(If other than Item 7)8. ADDRESS OFFER TO

NSN 7540-01-152-8064

PREVIOUS EDITION NOT USABLE

7. ISSUED BY

RATING PAGE OF

PAGESSOLICITATION, OFFER AND AWARD

2. CONTRACT NO. 5. DATE ISSUED 6. REQUISITION/PURCHASE NO.4. TYPE OF SOLICITATION

A. NAME B. TELEPHONE NO. (Include area code) (NO COLLECT CALLS)

15A. NAME

AND

ADDRESS

OF

OFFEROR

16. NAME AND TITLE OF PERSON AUTHORIZED TO SIGN OFFER

(TYPE OR PRINT)

18. OFFER DATE17. SIGNATURE15B. TELEPHONE NO. (Include areacode) 15C. CHECK IF REMITTANCE ADDRESS

IS DIFFERENT FROM ABOVE - ENTER

SUCH ADDRESS IN SCHEDULE

27. UNITED STATES OF AMERICA 28. AWARD DATE

AWARD

(Hour)

NEGOTIATED (RFP)

CODE CODE

FACILITY

NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

26. NAME OF CONTRACTING OFFICER

13. DISCOUNT FOR PROMPT PAYMENT

3. SOLICITATION NO.

period is inserted by the offeror)

(See Section I, Clause No. 52-232-8)

(The offeror acknowledges receipt of amendments to the SOLICITATION for offerors and related doc-uments numbered and dated:

10 CALENDAR DAYS 20 CALENDAR DAYS 30 CALENDAR DAYS CALENDAR DAYS

AMENDMENT NO. DATE AMENDMENT NO. DATE

SEC. PAGE(S)DESCRIPTION

(To be completed by Government)

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 350)

SEALED BID (IFB)

NOTE: In sealed bid solicitations "offer" and "offeror": mean "bid" and "bidder".

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-10. All offers are subject to all terms and conditions contained in this solicitation.

(REV. 4-85)

22. AUTHORITY FOR USING OTHER THAN FULL AND OPEN COMPETITION:

M ITEM23. SUBMIT INVOICES TO ADDRESS SHOWN IN(4 copies unless otherwise specified)41 U.S.C. 253(c)( )10 U.S.C. 2304(c)( )

OFFER (Must be fully completed by offeror)

PART - THE SCHEDULE PART - CONTRACT CLAUSES

PART - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACH.

PART - REPRESENTATIONS AND INSTRUCTIONS

DO-A1 1 66

SPRPA1-26-R-YB46 X 2026 APR 23 26042-0006

SPRPA1

DLA AVIATION AT PHILADELPHIA, PA

DLR PROCUREMENT OPERATIONS (AP)

700 ROBBINS AVENUE BUILDING 26

PHILADELPHIA PA 19111-5098

BLDG 1 ROOM 2223 02:00PM 2026 MAY 26

K. LAUBER APBB.22 (213) 737-3962

X 1 X 21 X 2 X 4 X 44

X 7 X 15

X 17 X 45 X 18 X 58 X 20 X 64

PAGES

OFPAGEREFERENCE NO. OF DOCUMENT BEING CONTINUED

NAME OF OFFEROR OR CONTRACTOR

CONTINUATION SHEET

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

SPRPA1-26-R-YB46 2 66

0001 NSN 7RH 1720-01-465-7848 EY

BUFFER CYL ASSY SHELF LIFE 0-00

SEE TECHNICAL REQUIREMENTS IN SECTIONS C, D, E, AND ATTACHMENTS

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT UNIT PKCU OPI

N 001 000 41 1 00 EA GH D EC A 00 O 00 EQQ 0.0 0.000 M

PACKAGING IS IN ACCORDANCE WITH MIL-STD-2073

THIS IS A ALRE CRITICAL SAFETY ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC

LKE DRAWING UPDATE SHEET.

NAVSUP REFERENCE ONLY: PROCUREMENT TDR 24-10108

THE COMPONENTS BEING ACQUIRED UNDER THIS SOLICITATION HAVE BEEN CLASSIFIED AS

"CRITICAL" REQUIRING ENGINEERING SOURCE APPROVAL BY NAVAL AIR SYSTEMS COMMAND

ONLY THOSE COMPANIES WHO HAVE SUBMITTED AND BEEN APPROVED WILL BE ELIGIBLE FOR

AWARD UNDER THIS SOLICITATION. ANY COMPANY MAY SUBMIT A SOURCE APPROVAL

REQUEST AS OUTLINED IN THIS SOLICITATION.

All records pertaining to ALRE CSI/CAI manufacture and inspection/test shall be provided to the ALRE Cognizant Technical Authority. All records shall be maintained by LKE QA and by the manufacturer for a period of seven years.

SHIP TO

0001AA N00383-24-X-2836 W25G1U 23 EA

TP: 2

0001AB SEE DD FORM 1423 1 LO NSP

EXHIBIT "A"

SOLICITATION NOTES:

Please submit all Post Award Requests (PARs) to dlawsphlpostawd@dla.mil .

Include the Contract, Solicitation, and PR number, the Contracting Officer?s Nae, and the purpose of the request. Please be as specific as possible. Whole order or specific CLIN/CLINs? Include all relevant information and supporting documntation, if necessary.

100% Small Business Set Aside applies to this procurement.

THIS IS A CRITICAL SAFETY ITEM (CSI).

For Critical Safety Items (CSI), DFARS clause 252.209-7010, Identification of Critical Safety Items, is incorporated by reference.

This solicitation includes procurement note L09 Reverse Auction (Oct 2016) from DLAD 15.407-90. The Government may conduct a reverse auction.

PAGES

OFPAGEREFERENCE NO. OF DOCUMENT BEING CONTINUED

NAME OF OFFEROR OR CONTRACTOR

CONTINUATION SHEET

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

SPRPA1-26-R-YB46 3 66

The following is included in section M of this solicitation:

The Government will consider all responsible offerors/quoters for the award.

The Government will evaluate offerors/quoters based on price, delivery timeframe, and past performance. All evaluation factors other than cost or price, when combined, are approximately equal to cost or price.

Please email copy of proposal to kenneth.lauber@dla.mil

INSPECTION AT ORIGIN

ACCEPTANCE AT ORIGIN

POC FAX: (215) 737-7149

POC EMAIL: KENNETH.LAUBER@DLA.MIL

SPRPA1-26-R-YB46 PAGE 4 OF 66

PART I - THE SCHEDULE

SECTION C

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

CLIN: 0001

NIIN: 014657848 ACTIVITY USE ONLY: TDP VERSION NO.: 010

ITEM NAME: BUFFER CYL ASSY

1. SCOPE

1.1 . Markings shall be in accordance with MIL-STD-130.

1.2 PRE-AWARD / POST AWARD REQUIREMENTS:

Due to the critical use of this item and its quality history, a pre-award survey and post-award conference may be required for all new manufacturers. For all previous sources, a post-award conference may be recommended.

1.3 The components being acquired under this solicitation have been classified as Flight Critical requiring engineering source approval by the Naval Air Systems Command. Only those companies who have submitted requests for source approval and been approved will be eligible for award under this solicitation. Any company not previously approved may submit a Source Approval Request to the contracting officer, Naval Inventory Control Point, (See Block 10 of the SF33 for name and code). The Source Approval Request shall contain the following documentation and shall be submitted by the closing date of this solicitation:

(A) Copy of complete configuration drawings for a similar item(s) which your company has produced within the past three years, including test procedures for which your company (1) has been qualified to manufacture and (2) which is similar, i.e., requires the same materials, manufacturing processes, inspections, tolerances and similar application as the item(s) for which you are seeking approval.

(B) Copy of the complete process/operation sheets used to manufacuture the similar item, including but not limited to, detailed shop sketches. These plans must note those operations and processes performed by subcontractors/ vendors.

(C) Complete copies of purchase orders, shipping documents, etc. that document delivery of production quantities of the part to the Original Equipment Manufacturer or Military service. Provide the most recent copies of the documents.

(D) A detailed comparative analysis of the differences/similarities between the similar part and the part(s) for which you are seeking approval. This analysis should include materials, configuration, tolerances, process requirements, dimensions, castings, forgings, etc.

(E) Copy of inspection method sheets used in the manufacturing and at final inspection. These sheets should include actual tolerance, print requirements, inspection devices, sources performing the operation and level of inspection.

Critical characteristics should be discernible from all other characteristics.

The above requirements are a subset of requirements specified in the ASO Source Approval Information Brochure dated January 1995. The submission of this data subset is contingent upon and in consideration of the submitting contractor meeting all other requirements specified in this solicitation to include a bilateral agreement with MDA which includes availability of complete data, MRB disposition, etc. Any company not having such agreement, but desiring to seek engineering source approval, will be required to submit data meeting all requirements of the ASO/NAVICP Source Approval Brochure.

1.4 Sampling rates (AQLs) indicated below shall be used in accordance with ANSI Z1.4 for Single Sampling and a General Inspection Level of II.

1.5 In addition to the 100% PCO Mandatory, critical and major characteristics, attributes for plating, hardness and non-destructive testing will be inspected one hundred percent.

1.6 Contractor shall develop a system for identification of individual piece parts for traceability purposes. Markings shall not be permanent.

1.7 An AQL of 1.5 will be used for Class 3 threads and dimensions, and geometric feature controls with a tolerance range of .010 or less.

1.8 For minor characteristics, a sampling rate determined by the contractor and subject to QAR approval will be used.

SPRPA1-26-R-YB46 PAGE 5 OF 66

1.9 The material covered in this contract/purchase order will be used in a crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital shipboard systems or loss of aircraft. Therefore,the material has been designated as Critical material and special control procedures are invoked to ensure receipt of correct material.

1.10 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with <NAWC LAKEHURST> drawing number ( <80020> ) <613466> , Revision <W> and all details and specifications referenced therein.

1.11 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.

1.12 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.

2. APPLICABLE DOCUMENTS

2.1

DRAWING NO. CAGE REV DOC TYPE DISTR CD SHEET NR REV TYPE SIZE

A316214 80020 AR D

A316215 80020 AK D

A316242 80020 G D

A414240 80020 AF D

B414463 80020 Y A B91477 80020 W D

MPR 1222 80020 A D

MPR 1223 80020 C D

323199 80020 D A 323201 80020 E D 323207 80020 H D 416451 80020 M D 416452 80020 G D 416453 80020 E D 416454 80020 G D 416455 80020 H D 416456 80020 L D 416457 80020 J A 416458 80020 F D 416459 80020 G D 416538 80020 E D 416539 80020 K D 416541 80020 F D 416542 80020 H D 416543 80020 R D 416547 80020 C A 416548 80020 G D 416560 80020 F D 418417 80020 F D 418418 80020 G D 418420 80020 P A 511016 80020 K D 511225 80020 H A 513392 80020 H D 520220 80020 J A 613466 80020 W D 613662 80020 M D

3. REQUIREMENTS - NOT APPLICABLE

WSSTERMCZ01

CONFIGURATION MANAGEMENT AND CONTROLS

1.0 Configuration Management

1.1 The cognizant Naval Air Systems Command (NAVAIR) Program Manager will maintain configuration control and change authority for all items in this contract.

SPRPA1-26-R-YB46 PAGE 6 OF 66

WSSTERMCZ01 (CONT)

CONFIGURATION MANAGEMENT AND CONTROLS

1.2 In accordance with the configuration management provisions of this contract, the Contractor must maintain the total Equipment baseline configuration of the parts on this contract including, but not limited to, hardware, software and firmware.

NOTE: The latest revisions of the DOD Forms referenced in this term can be found at https://www.esd.whs.mil/dd. The latest revisions of the DIDs referenced in this term can be found at https://quicksearch.dla.mil/.

2.0 Engineering Changes

2.1 The Government will not be responsible for any contract delay or disruption or any increased costs of performance of the Contractor due to a misclassification of an Engineering Change Proposal (ECP) by the Contractor, including those costs associated with replacement of delivered items resulting from such a misclassification. ECP's are classified as Class I (Major) or Class II (Minor). For detailed classification criteria refer to the DD Form 1692 instructions sheet. ECPs must be prepared in accordance with DI-SESS-80639E, Engineering Change Proposal (ECP).

NOTE: Any ECP or notification of an ECP submitted to the PCO in accordance with this paragraph must also be copied to the NAVSUP WSS CM Team at usn.philadelphia.navsupwssphil.mbx.configuration-management@us.navy.mil.

2.1.1 Class I (Major) Changes: The Contractor must coordinate with the cognizant NAVAIR Program Office prior to any Class I ECP submission. The Contractor must submit all Class I changes, via the Defense Contract Management Agency (DCMA) Contract Management Office (CMO) and the Procurement Contracting Officer (PCO), to the cognizant NAVAIR Program Office for approval or disapproval. The Contractor must notify the PCO of any pending or approved Class I engineering changes with another Government activity that the Contractor proposes to incorporate under this contract.

The cognizant NAVAIR Program Office will approve or disapprove of all Class I changes. Any approved Class I change may necessitate contract changes by the contracting officer, which changes may be handled under the Changes clause of this contract, FAR 52.243-1. The Contractor must not implement a Class I change on this contract until a contract modification is issued by the PCO.

2.1.2 Class II (Minor) Changes: Any Class II change involving a Critical Safety Item (CSI) must be submitted to the PCO for NAVAIR Program Office approval unless NAVAIR has delegated approval authority to the cognizant DCMA CMO. For Class II changes to items without a criticality determination, the items will be considered CSI for the purposes of processing in accordance with this paragraph. Class II changes related to non-CSI's must be submitted to the cognizant DCMA CMO for concurrence in classification and may be implemented only upon receiving DCMA concurrence.

Class II changes must be made at no additional cost to the Government.

2.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a Class I or Class II ECP.

3.0 Variances

3.1 The Contractor must not deliver any item for acceptance by the Government that incorporates a known departure from product definition information unless a Request for Variance (RFV) has been approved. Authorized variances are a temporary departure from the requirements only and do not authorize a change to the item's approved configuration.

RFV's are classified as Critical, Major, or Minor. For detailed classification criteria refer to the DD Form 1694 instructions sheet. Any variance requests to CSI's must be classified as major, at a minimum. For variances to items without a criticality determination, the items will be considered CSI for the purposes of processing and classified as a major, at a minimum. Variance requests shall be prepared in accordance with DI-SESS-80640E - Request for Variance (RFV).

NOTE: Any RFV submitted to the PCO in accordance with this paragraph must also be submitted to the NAVSUP WSS RFV Review Team at usn.philadelphia.navsupwssphil.mbx.rfv-review-team@us.navy.mil.

NOTE: Should a variance be discovered after product delivery, the Contractor must notify the PCO and NAVSUP WSS Quality (NOE_N22@us.navy.mil).

3.1.1 Critical/Major Variances: The Contractor must submit all critical/major variance requests, via the DCMA CMO and the PCO, to the cognizant NAVAIR Program Office for approval or disapproval. All approved critical/major variances require a contract modification by the PCO prior to final inspection and acceptance of the items.

SPRPA1-26-R-YB46 PAGE 7 OF 66

WSSTERMCZ01 (CONT)

CONFIGURATION MANAGEMENT AND CONTROLS

3.1.2 Minor Variances: For minor RFVs, delivery and/or shipment of such items under this contract is not permitted until approved by the cognizant DCMA CMO.

3.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a critical, major, or minor variance.

(12/23)

PART I - THE SCHEDULE

SECTION D

PACKAGING AND MARKING

CLIN: 0001

NIIN: 014657848 ACTIVITY USE ONLY: TDP VERSION NO.: 010

ITEM NAME: BUFFER CYL ASSY

5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

252.211-7003

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(a) Definitions. As used in this clause --

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means --

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

"Data qualifier" means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot, or batch number; and the serial number.

"Enterprise" means the entity (e.g., a manufacturer or vendor)responsible for assigning unique item identifiers to items.

"Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Government's unit acquisition cost" means --

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

SPRPA1-26-R-YB46 PAGE 8 OF 66

252.211-7003 (CONT)

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

"Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subasssembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination off numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at https://www.acq.osd.mil/asda/dpc/ce/ds/ unique-id.html

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

SPRPA1-26-R-YB46 PAGE 9 OF 66

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more, except for the following line items:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(If items are idenified in the Schedule, insert "See Schedule" in this table.)

(iii) Subassemblies, components, and parts embedded within delivereditems, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number < > .

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number < >

(v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology Interrnational symbology specification Data matrix; ECC200 data matrix specification.

(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that --

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology EAN/UCC Appliccation Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology--EAN/UCC Application Ideentifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology-Transfer Syntax for High Capacity Automatic Data Capture Media.

(5) Unique item identifier.

(i) The Contractor shall--

(A) Determine whether to--

(1) Serialize within the enterprise identifier;

(2) Serialize within the part, lot, or batch number; or

(3) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only:

Original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the

SPRPA1-26-R-YB46 PAGE 10 OF 66

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version;

(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and

(D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version.

(ii) The issuing agency code--

(A) Shall not be placed on the item; and

(B) Shall be derived from the data qualifier for the enterprise identifier.

(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information:

(1) Unique item identifier.

(2) Unique item identifier type.

(3) Issuing agency code (if concatenated unique item identifier is used).

(4) Enterprise identifier (if concatenated unique item identifier is used).

(5) Original part number (if there is serialization within the original part number).

(6) Lot or batch number (if there is serialization within the lot or batch number).

(7) Current part number (optional and only if not the same as the original part number).

(8) Current part number effective date (optional and only if current part number is used).

(9) Serial number (if concatenated unique item identifier is used).

(10) Government's unit acquisition cost.

(11) Unit of measure.

(12) Type designation of the item as specified in the contract schedule, if any.

(13) Whether the item is an item of Special Tooling or Special Test Equipment.

(14) Whether the item is covered by a warranty.

(e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information:

(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part.

(2) Unique item identifier of the embedded subassembly, component, or part.

(3) Unique item identifier type.**

(4) Issuing agency code (if concatenated unique item identifier is used).**

(5) Enterprise identifier (if concatenated unique item identifier is used).**

(6) Original part number (if there is serialization within the original part number).**

(7) Lot or batch number (if there is serialization within the lot or batch number).**

(8) Current part number (optional and only if not the same as the original part number).**

(9) Current part number effective date (optional and only if current part number is used).**

(10) Serial number (if concatenated unique item identifier is used).**

(11) Description.

**Once per item.

(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:

(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/.

(2) Embedded items shall be reported by one of the following methods--

(i) Use of the embedded items capability in WAWF;

(ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/; or

(iii) Via WAWF as a deliverable attachment for exhibit line item number < > , Unique Item Identifier

Report for Embedded Items, Contract Data Requirements List, DD Form 1423.

(g) Subcontracts. If the Contractor acquires by subcontract any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial products or commercial services.

WSSTERMDZ03

PRESERVATION, PACKAGING, PACKING AND MARKING

The contractor shall preserve, package, pack and mark all items as cited below. Where specifications or standards are cited herein the latest revision of that specification shall apply.

SPRPA1-26-R-YB46 PAGE 11 OF 66

WSSTERMDZ03 (CONT)

PRESERVATION, PACKAGING, PACKING AND MARKING

1. PRESERVATION REQUIREMENTS

a. SYSTEM STOCK SHIPMENTS - The contractor shall preserve all items intended to enter the military distribution system for stock in accordance with the MIL-STD-2073-1, "Standard Practice for Military Packaging", Packaging Requirements Code specified in Section B, Part I of the Schedule. When a Specialized Preservation Code/Method of Preservation (MOP) (Table J-Ia) is specified, and one or more of the following packaging fields (WM, CUD, CT, UC) value is a 00 (numeric), the Specialized Preservation/MOP procedure and materials takes precedence. Contractors should disregard the LP field and third digit of the PACK field and use the Unit Container Level (UCL) to identify the level of packing protection the unit container meets for packing requirements. When HM = D, the item is regulated in accordance with Title 49 Code of Federal Regulations (CFR); when HM = N the item is not regulated for transportation.

1) When a specified packaging material has an associated Qualified Products List (QPL), the contractor shall use only packaging materials produced by a manufacturer listed on the applicable QPL. Barrier materials that have QPLs are MIL-PRF-131, MIL-PRF-81705, MIL-PRF-22191, MIL-PRF-3420 and MIL-PRF-22019. Sources for QPL material can be obtained from the Qualified Products Database at http://qpldocs.dla.mil/.

b. IMMEDIATE USE/INSTALLATION AND PART NUMBER BUY SHIPMENTS - Government PCO or ACO approval is required to use the packaging standards outlined in this paragraph. Any national stock numbered (NSN) item required for immediate use (used or consumed within 7 days of receipt) or direct installation, or part numbered item (authority granted to ship without NSN) shall be preserved and packed in accordance with ASTM D3951-18 (2023), "Standard Practice for Commercial Packaging", for all shipments to a Continental United States (CONUS) government activity or contractor-owned facility. All material destined for overseas shipment (OCONUS) shall be preserved in accordance with MIL-STD-2073-1.

c. GOVERNMENT-OWNED MATERIAL - In the event that the contract expires, is terminated, or completed, and Government-owned material is to be returned to the supply system, the contractor shall preserve and package this material in accordance with the requirements of paragraph 1.a.

2. PROTECTION FROM DEGRADATION DUE TO ELECTROSTATIC (ES)/ELECTROMAGNETIC (EM) FORCES

a. When ASTM D3951-18 (2023), is authorized for packaging and the item is considered Electrostatic Discharge

Sensitive (ESDS), protection shall be in accordance with ANSI/ESD S20.20-2021, "For the Development of an ESD Control Program for - Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices)."

b. When MIL-STD-2073-1 is specified and the preservation method code (PMT) in the solicitation does not specify ESD/EM protection (PMT = GX) and the contractor's proposed item of supply is subject to degradation from ES/EM forces, contractors shall provide recommended packaging data with their proposals/quotes.

3. PACKING REQUIREMENTS - The contractor shall pack as follows:

Domestic Shipments (CONUS): Level B

Overseas Shipments (OCONUS) (including Navy ships at sea):

Via air, FPO, APO Level B

Via freight forwarder Level B

Via surface Level A

Exterior shipping containers for Packing Levels A and B are listed in MIL-STD-2073-1, Appendix C, Table C.II.

Long-life reusable containers, and wood containers are shipping containers which do not require overpacking for shipment.

4. MARKING REQUIREMENTS - All unit, intermediate and shipping containers shall be marked in accordance with MIL-STD-129. In addition, the following specific requirements apply:

a. ADDITIONAL MARKING FOR SPARES ONLY - Each MIL-STD-129 label shall also include the following:

1) Procurement Instrument Identifier (PIID) - the 13-digit contract order number,

2) Contract Line Item Number (CLIN) - the 4-digit individual line item number (e.g. 0001, 0002, etc.), and

3) SubCLIN - the 6-digit sub line item number (e.g. 0001AA, 0001AB, 0002AA, 0002AB, etc.).

b. DEPOT LEVEL REPAIRABLE (DLR) LABELS

1) Items identified with a Cognizance (COG) Code of either "7" or an even number preceding the NSN, excluding 6A, 6H and 6X COGs (e.g. 7RH 5826-014289999), are defined as Depot Level Repairable (DLR) items. DLR items require that a DLR label be placed on the outside of the unit, intermediate and shipping containers as close to the bar code label as possible.

SPRPA1-26-R-YB46 PAGE 12 OF 66

PRESERVATION, PACKAGING, PACKING AND MARKING

EXCEPTION: When a DLR item requires use of both a reusable inner unit container and a reusable outer shipping and storage container (excluding wood and fiberboard), only the inner unit container shall be affixed with a DLR label. In these cases only, DLR labels shall NOT be placed on the outer reusable container.

2) Labels are available via the Naval Forms Online website: https://forms.documentservices.dla.mil/order/. The website will advise the procedures for ordering and establishing an account.

3) NAVSUP WSS authorizes contractors to create and print their own DLR labels.

Labels shall follow the standard size and font options listed in below chart. Text shall be in all upper case letters of the same style font. The label used shall be sized proportionate to the size of the container. Labels shall be horizontally printed and consist of yellow "DLR" text font on a solid blue background. Labels shall meet requirements of MIL-STD-129 section 4.2.2. Labels shall be of a water-resistant grade of paper, film, or plastic, coated on one side with water-insoluble, permanent type adhesive. The adhesive shall adhere to metal, plastic, aluminum or fiberboard surfaces under high and low temperatures. Labels shall have a finish suitable for printing and writing on with ink without feathering or spreading, be capable of withstanding normal handling and storage conditions, and remain securely in position. Application specific performance criteria and durability requirements to ensure functionality in various climatic environments should be tailored, if required, using MIL-PRF-61002. MIL-PRF-61002 can be used as an acquisition tool when labels presently being used are not performing satisfactorily or when new conditions or applications require special label stock for those particular situations.

NSN DESCRIPTION QUANTITY APPLICATION FORM NUMBER

PER UNIT

PACKAGE

0108LF5055300 DLR Label 100 Unit Container NAVSUP 1397-1

2in.x3in.

0108LF5055000 DLR Label 100 Intermediate/ NAVSUP 1397

3in.x5in. Shipping Container

c. SPECIAL MATERIAL IDENTIFICATION CODE (SMIC) FOR NAVSUP WSS MARITIME REQUIREMENTS ONLY

1) Certain Program-related items are identified by a two-position SMIC, which appears as a suffix to the NSN

(e.g. 1H 4730 009001317 L1), and require special markings. Containers shall be marked or labeled with letters, maximum two inches high on two (2) sides and two (2) ends as follows:

SMIC MARKINGS COLOR TYPE CONTAINER

L1 LEVEL 1 RED Unit, intermediate and Shipping

(size permitting) S1 Surface RED Unit, intermediate and Shipping

LEVEL 1 (size permitting) D4/D5/D7 DSS-SOC RED Unit, intermediate and Shipping

(size permitting) C1* LEVEl 1 Special GREEN Unit, intermediate and Shipping

CLEAN O2-N2

CP/VG* SPECIAL CLEAN GREEN Unit, intermediate and Shipping

O2-N2 D0/D6/D8* DSS-SOC SPECIAL GREEN Unit, intermediate and Shipping

CLEAN O2-N2

VU FBW SFCC VU Blue Unit, intermediate and Shipping

(size permitting) SW FBW SFCC SW BLUE Unit, intermediate and Shipping

(size permitting) Q3/Q5 Q3 or Q5 RED Unit, intermediate and Shipping

SPRPA1-26-R-YB46 PAGE 13 OF 66

PRESERVATION, PACKAGING, PACKING AND MARKING

* denotes Oxygen Clean requirements in accordance with MIL-STD-1330 "Precision Cleaning and Testing of Shipboard Oxygen, Helium, Helium-Oxygen, Nitrogen, and Hydrogen Systems."

5. PALLETIZATION. Palletization of shipments shall be accomplished in accordance with MIL-STD-147 "DOD Standard Practice: Palletized Unit Loads." Failure to meet these palletization/packaging requirements and measures, without a written waiver from the PCO or ACO, may result in charges back to the contractor for repalletization and/or repackaging of items. Pallets shall conform to the requirements of American National Standards Institute, Material Handling-MH1-2016, Pallets, Slip Sheets, and Other Bases for Unit Loads. MH1-2016 may be obtained at the following website: http://www.mhi.org.

a. General Purpose Unit Loads - When shipping directly to a Navy afloat unit, pallets meeting MH1-2016, Part No.

MH1/9-02SW4048 or MH1/9-10BW4048 for unit loads under 1,500 pounds and MH1/9-03SW4048 for unit loads over 1,500 pounds shall be used.

b. Hazardous Material Unit Loads - Unless otherwise specified in the contract or purchase order hazardous material containers, except cylinders and 55 gallon drums, shall be palletized utilizing MH1-2016 Part No. MH1/9-07SW4848 pallets.

c. Use of nonstandard commercial pallets is prohibited.

6. WOOD PACKAGING MATERIAL (WPM). All shipments destined to the DOD must be treated and marked in accordance with the International Standards for Phytosanitary Measures Guidelines for Regulating Wood Packaging Material in International Trade (ISPM 15).

a. For all WPM furnished under this contract the contractor shall ensure the American Lumber Standards Committee (ALSC) approved mark is applied to every shipment regardless of destination.

b. Failure to comply with the requirements of ISPM 15 may result in refusal of the shipment, destruction or corrective treatment of WPM at the point of receipt and the associated costs charged back to the contractor.

7. NAVY SHELF LIFE PROGRAM. Navy shelf-life requirements are listed under the item description in a 3-digit alpha/numeric code. Position one (1) is the DOD shelf-life code, defining the type of shelf-life for an item (Type I, non-extendible or Type II, extendible), and the number of months an item can remain ready for issue in a Navy specified package. Positions two (2) and three (3) combined form the Navy-unique shelf-life action codes used by storage activities, and do not impose any requirements on the contractor. The contractor shall use the applicable shelf-life paragraphs and table in MIL-STD-129 to apply either Type I or Type II shelf-life markings to an item's unit, intermediate and shipping containers. Contractors will ensure that at least eighty-five percent (85%) of the Navy shelf-life requirement is remaining when received by the first government activity.

8. REUSABLE NSN CONTAINERS. An item that has an NSN assigned in the "Container NSN" field (e.g . 8145 012622982) requires shipment in a reusable shipping and storage container.

a. REUSABLE CONTAINERS FOR NAVSUP WSS, MARITIME REQUIREMENTS - Reusable NSN containers for maritime material (designated by a COG Code of "7E", "7G" and "7H") shall be provided as contractor-furnished material (CFM).

b. REUSABLE CONTAINERS FOR NAVSUP WSS, AVIATION REQUIREMENTS - Reusable NSN containers (excluding fiberboard and most wood) for aviation material (designated by a COG Code of "7R", "6K" or "0R") shall be provided as government-furnished material (GFM). Fast pack containers will not be provided as GFM. To obtain GFM reusable containers, the contractor must request via email usn.philadelphia.navsupwssphil.mbx.navsupcrf@us.navy.mil at least 90 days prior to the anticipated shipping date, 30 days prior for repair contracts. If the Navy's Container Management Area (CMA) informs the contractor that containers are unavailable, the following alternate packaging requirements apply. The unavailability of reusable containers shall not be an excusable delivery delay.

ALTERNATE PACKAGING REQUIREMENTS FOR ITEMS ASSIGNED THE FOLLOWING CONTAINERS

Container Container Alternative Packaging Code NSN Part Number (80132) IAW MIL-STD-2073-1 8145 002609548 P069-2

8145 002609556 P069-1 N 001 000 GX 1 00 K3 LT B ED

8145 002609559 P069-3 UCL = B

8145 002609562 P069-4 SPMK = 39

8145 010124088 P069-6 PACK = QFF

8145 010140440 P069-5 8145 011644073 P069-7

8145 012622982 15450-1 IF MOP/PMT = GX,

SPRPA1-26-R-YB46 PAGE 14 OF 66

PRESERVATION, PACKAGING, PACKING AND MARKING

--------------------------------------- N 001 000 GX 1 00 K3 GH Z ED

8145 012622983 15450-2 Z= use 1.5" of "GH" cushioning --------------------------------------- between barrier bag and Unit Container

8145 012622984 15450-3 UCL = B

--------------------------------------- SPMK = 39

8145 012622985 15450-4 PACK = QFF

8145 012622986 15450-5 For all other MOPs/PMTs

--------------------------------------- N 001 000 51 1 00 EA GH F ED

8145 012622987 15450-6 UCL = B

--------------------------------------- SPMK = 03

8145 012622988 15450-7 PACK = QFF

c. All excess empty reusable shipping and storage containers shall be turned-in to the nearest Container Reuse and Refurbishment Center (CRRC). CRRC locations/points of contact: Program Manager - 215-697-2063

Norfolk, VA - 757-445-9099 ext. 124 Yokosuka, JAPAN - 011-81-46-816-6304 Cherry Point, NC - 252-466-2331 Lemoore, CA - 559-998-0220 Jacksonville, FL - 904-542-1014 Okinawa, JAPAN - 011-81-46-816-6304 San Diego, CA - 619-545-8360 Iwakuni, JAPAN - 011-81-46-816-6304 Puget Sound, WA - 360-476-9777 Bahrain - 011-318-439-9553

d. The stock-numbered, long-life, reusable containers identified herein as GFM are property of the U.S. Navy and only shall be used to fulfill orders from the Navy and U.S. Marine Corps; these containers shall not be used to fulfill orders from the U.S. Army, U.S. Air Force, any other agency of the U.S. Government or Foreign Military Sales (FMS) customer.

9. REUSABLE NSN CONTAINERS FOR FOREIGN MILITARY…