SQS_EDA.PDF

PDF 378 KB Posted Aug 22, 2018

Attached to: Towing Eye, Aircraft
Solicitation number: SPRHA1-18-Q-1574
Issued by: Department of the Air Force Materiel Command Ogden Air Logistics Complex

About this file

From the source

Attachments

View the file

Other files

File	Type	Posted
SPRHA118Q1574.pdf	PDF	Aug 22, 2018

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

DD FORM 1423-1, FEB 2001

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

PREVIOUS EDITION MAY BE USED.

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services and Communications Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP ________ TM _______ OTHER

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

15. TOTAL

16. REMARKS

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

G. PREPARED BY H. DATE I. APPROVED BY J. DATE

Page of Pages

1_DATA_ITEM_NO: A001

2_TITLE_OF_DATA_ITEM: Test/Inspection Reports

3_SUBTITLE: Government Testing

4_AUTHORITY_Data_Acquisit: DI-NDTI-80809B

5_CONTRACT_REFERENCE:

6_REQUIRING_OFFICE: 417 SCMS/CL

7_DID_250_REQ: Y

8_APP_CODE:

DIST_STATEMENT: B

10_FREQUENCY: 1

11_AS_OF_DATE: Per contract reqs

12_DATE_OF_FIRST_SUBMISSI: Per contract reqs

13_DATE_OF_SUBSEQUENT_SUB:

addressee1: Preferred method of draft1:

reg1: 1 repro1:

draft13:

reg13:

repro13:

addressee14:

draft14:

reg14:

repro14:

addressee15:

draft15:

reg15:

repro15:

addressee16:

draft16:

reg16:

repro16:

addressee17:

draft17:

reg17:

repro17:

addressee18:

draft18:

reg18:

repro18:

addressee19:

draft19:

reg19:

repro19:

addressee20:

draft20:

reg20:

repro20:

addressee21:

draft21:

reg21:

repro21:

addressee22:

draft22:

reg22:

repro22:

addressee23:

draft23:

reg23:

repro23:

addressee24:

draft24:

reg24:

repro24:

addressee25:

draft25:

reg25:

repro25:

addressee26:

draft26:

reg26:

repro26:

addressee27:

draft27:

reg27:

repro27:

addressee28:

draft28:

reg28:

repro28:

addressee29:

draft29:

reg29:

repro29:

addressee30:

draft30:

reg30:

repro30:

addressee31:

draft31:

reg31:

repro31:

addressee32:

draft32:

reg32:

repro32:

addressee33:

draft33:

reg33:

repro33:

addressee34:

draft34:

reg34:

repro34:

addressee35:

draft35:

reg35:

repro35:

addressee36:

draft36:

reg36:

repro36:

addressee37:

draft37:

reg37:

repro37:

addressee38:

draft38:

reg38x:

repro38:

total_draft: 0 total_repro: 0

16_REMARKS: 1. BLOCK 4: Contractor format acceptable. Paragraph 10.2.3.3 of DI-NDTI-80809B is clarified as follows:

a. All dimensions and tolerances specified on the manufacturing data shall be listed in one column with the actual corresponding reading obtained from the inspection of the parts listed in another column.

b. Materials utilized in the manufacture of the "First Article" item shall be identified and certified along with a copy of material purchase requests as conforming to applicable data requirements.

c. Material processing, including finish requirements (plating, heat treatment, welding, inspecting, anodize, painting, etc.) utilized in the manufacture of the "First Article" item shall be identified and certified as conforming to applicable requirements. A copy of the purchase order certifying the process accomplished at other than contractor facility shall be included.

d. Other requirements as called out with the Technical Data Package.

2. BLOCK 9: Distribution authorized to U.S. Government Agencies only, test and evaluation, 11 March 2016. Other requests for this document shall be referred to 417 SCMS.

3. BLOCKS 10, 11, 12, and 13: Report to assist in the "First Article" testing by the Air Force shall be submitted concurrently with the "First Article" item.

FOB: DESTINATION

INSPECTION/ACCEPTANCE: DESTINATION

17_PRICE_GROUP:

ESTIMATED_TOTAL_PRICE:

G_PREPARED_BY: Lori Grygier Lead IM, 417 SCMS/GUMD

H_DATE: 20170308

J_DATE: 20170308

Page: 1 reg38t: 1

A_CONTRACT_LINE_ITEM_NO:

B_EXHIBIT: A

TDP:

TM:

OTHER:

DSYSTEMITEM: First Article

E_CONTRACTPR_NO:

FCONTRACTOR:

of_pages: 1

Reset:

addressee13:

addressee12:

addressee11:

addressee10: 84056-5713 addressee9: Hill AFB, UT addressee8: Non Accountable Bay addressee7: Bldg. 849 Attn:

addressee6: 809 MXSS/MXDEB addressee5: FB2029 addressee4: container:

addressee3: report in First Article addressee2: shipping to include test

2017-03-08T08:31:48-0700

MARTIN.BRAD.H.1256609564

ENGINEERING DATA LIST

DATE:

17 OCT 2014

REVISION: 3 *HISTORY*

CAGE:

81205

PAGE:

NSN:

1620012975410LE

DATA TECH:

Lehr, Gerald L

END ITEM:

B-2 LANDING GEAR

ORGANIZATION/OFFICE SYMBOL:

429 SCMS GUMACB/

MANUFACTURER NAME:

THE BOEING COMPANY

REFERENCE NUMBER:

DAA3222A152-001

NOUN:

TOWING EYE,AIRCRAFT

LINE/

SUB CAGE

ENG DRAWING NUM/ ACCOMP

DOC NUM REV

SHEETS

FURN

CODE

DIST

CODE NOUN REMARKS

L 81205 DAA3222A152 D S TOW FITTING ASSEMBLY -

MAIN LANDING GEAR

Lehr, Gerald L 27 OCT 2014

W/EO-11C2283-H, PL REV G W/EO-11C2284-H.

NAME: DATE:

L 81205 DAA3222D153 A S FORGING, TOW FITTING MLG Lehr, Gerald L 27 OCT 2014

W/ PL REV D.

L 81205 DAA3222D168 A S AXLE FITTING - MLG Lehr, Gerald L 27 OCT 2014

W/ PL REV D.

L 81205 DAA3222D400 E S BUSHING-MAIN & NOSE

LANDING GEAR

Lehr, Gerald L 27 OCT 2014

W/ PL REV N

L 81205 DAA3221D004 B S SEALING CONTROL - MLG

L 98747 200827953 A S LABEL, UNIQUE

IDENTIFICATION (UID),

LANDING GEAR

L 98747 HILL AFB FORM 462 X ENGINEERING DATA

REQUIREMENTS

(ATTACHMENT A)

STANDARD ENGINEERING TEXT

Lehr, Gerald L 21 OCT 2014

RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE OFFICE.

C - CLASSIFIED DOCUMENT.

S - FURNISHED WITH SOLICITATION.

M - STABLE BASE DRAWING REQUIRED; FURNISHED WITH

CONTRACT AWARD.

X - DATA SUPPLIED (NOT IN JEDMICS).

R - FURNISHED BY PCO UPON REQUEST.

P - PARTIAL DOCUMENT FURNISHED.

V - VENDOR DRAWING; (NOT PROVIDED).

G - GOV'T DOCUMENT.

O - OTHERS, CONTRACTOR MUST ACQUIRE.

A- DATA NOT AVAILABLE.

FURNISHED METHOD CODE LEGEND:

Page 1 of 1EDL Version 3Generated by PRPS using Jasper Reports on 29 Jun 2018

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

TOW FITTING ASSEMBLY – MLG (B-2 AIRCRAFT)

2. PART NUMBER:

3. NATIONAL STOCK NUMBER:

1620-01-297-5410LE

PREPARED BY:

ROBERT YOUNG

OFFICE SYMBOL:

417 SCMS/GUEB

December 30, 2014

HILL AFB FORM 462 Page 1 of 5

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC. WILL BE USED IN LIEU OF THE DATA INDICATED. THE

SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. MATERIAL REVIEW BOARD:

A. OO-ALC LANDING GEAR ENGINEERING RETAINS ALL RIGHTS TO REVIEW AND ACCEPT MATERIAL REVIEW BOARD (MRB’S) DISPOSITIONS PRIOR TO SHIPMENT OF DISCREPANT ITEM. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED FOR MRB DISPOSITION.

B. PRIOR TO CONTRACT AWARD, THE CONTRACTOR SHALL CERTIFY TO THE GOVERNMENT IN WRITING FULL COMPLIANCE WITH MANUALS, SPECIFICATIONS AND STANDARDS CALLED OUT AND REQUIRED FOR THE MANUFACTURE OF THIS CONTRACTED LANDING GEAR COMPONENT/ASSEMBLY. CONTRACTOR IS RESPONSIBLE TO COMPLETELY SEARCH THESE MANUALS, SPECIFICATIONS AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY TO MANUFACTURE LANDING GEAR COMPONENTS. ANY QUESTIONS CAN BE

FORWARDED TO OO-ALC LANDING GEAR ENGINEERING.

6. GENERAL SPECIFICATIONS

7. MARKING AND IDENTIFICATION PER MIL-STD-130 IN LIEU OF BAC5307 AND BAC5308.

HRI ETCHED DIRECTLY ON PART BUT TESA TAPE LABEL NOT APPLIED DIRECTLY TO PART: UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED TO EACH PART PER MIL-STD-130. THE UID SHALL CONTAIN HUMAN- READABLE INFORMATION (HRI) AND MACHINE-READABLE INFORMATION (MRI) MARKINGS. QUALITY AND TECHNICAL REQUIREMENTS FOR BOTH THE MRI AND HRI SHALL BE IN ACCORDANCE WITH SAE AS9132. THE METHOD OF MARKING FOR THE HRI SHALL BE LIMITED TO ELECTRO-CHEMICAL ETCHING, DOT PEEN, VIBRO PEEN, OR MICRO- MILL. THE DEPTH OF EACH MARK SHALL BE FROM .003 - .005 INCHES. THE HRI MARK WILL BE LIMITED TO 16 ALPHANUMERIC CHARACTERS INCLUDING THE VENDOR CAGE (FSCM) OF THE CONTRACTOR NAMED ON THE CONTRACT, DATE OF MANUFACTURE IN THE FORMAT MMYY, AND A UNIQUE 4-DIGIT NUMBER STARTING WITH 0001 IN NUMERICAL ORDER OF MANUFACTURE. THE HRI SHALL APPEAR AS “SN 9874701040001”. THE HEIGHT OF EACH ALPHANUMERIC CHARACTER IN THE HRI SHALL BE A MAXIMUM OF .125 INCHES. THE LOCATION OF THE HRI SHALL BE IDENTIFIED ON THE DRAWING. THE FULL DETAILED UID MARKING REQUIREMENTS SHALL BE APPLIED TO A TAG, SUPPLEMENTAL BAG OR OTHER PACKAGE THAT ENCLOSES THE INDIVIDUAL ITEM IN ACCORDANCE WITH DRAWING 200827953-05.

8. DRAWING: DAA3222A152 TOW FITTING ASSY-

9. CHEMICAL CONVERSION COATING PER MIL-DTL-5541 TO BROKEN ANODIZE SURFACE IN LIEU OF 17.10 AND MIL-C- 5541.

10. INSTALL SAFETY WIRING PER NASM33540 IN LIEU OF BAC5018.

11. KARON LINER PER SAE AS81934 IN LIEU OF MIL-B-81934.

12. INSTALL BUSHINGS PER THE FOLLOWING IN LIEU OF BAC5435.

THE BUSHING INSTALLATIONS SHALL BE ACCOMPLISHED IN SUCH A MANNER AS TO AVOID DAMAGE TO THE FINISH ON THE I.D. OF THE HOUSING INTO WHICH THE BUSHING IS INSTALLED, OR THE FINISH OF THE O.D. OF THE BUSHING. FORCED INSTALLATION OF SUB-ZERO INSTALLATIONS, SUCH AS THE USE OF A PRESS OR HAMMER IS

HILL AFB FORM 462 Page 2 of 5

NOT PERMITTED, AND IS NOT ACCEPTABLE. A SMALL NON-METALLIC HAMMER MAY BE USED TO TAP THE BUSHING

INTO ALIGNMENT WITH THE HOUSING BORE, OR TO SEAT THE BUSHING.

PRIOR TO BUSHING INSTALLATION, THE PARTS AND HOUSING BORE SHALL BE CLEANED WITH CLEANING

SOLVENT TO REMOVE ALL CONTAMINATION.

LIQUID NITROGEN SHALL BE USED FOR ALL SUB-ZERO INSTALLATIONS UNLESS SOME OTHER SUB-ZERO COOLANT IS SPECIFIED AND APPROVED BY OO-ALC LANDING GEAR ENGINEERING. THE SOAK TIME OF THE BUSHING IN THE LIQUID NITROGEN SHALL BE SUFFICIENT TO ALLOW THE BUSHING TO REACH THE SAME

TEMPERATURE AS THE COOLANT.

THE BUSHING SHALL BE INSTALLED INTO THE HOUSING IMMEDIATELY UPON REMOVAL FROM THE COOLANT WITH AN ABSOLUTE MINIMUM OF LOST TIME. TRIAL RUNS SHALL BE ACCOMPLISHED AS NECESSARY TO MINIMIZE INSTALLATION TIME WHICH SHOULD BE IN THE ORDER OF ABOUT SEVEN (7) SECONDS MAXIMUM.

IT MAY OCCASIONALLY BE NECESSARY TO HEAT THE HOUSING INTO WHICH THE BUSHING IS TO BE INSTALLED IN ADDITION TO SUB-ZERO COOLING OF THE BUSHING. DETAIL PARTS IN PROCESS WILL NOT HAVE PAINT, SEALANT OR OTHER ORGANIC MATERIAL APPLIED PRIOR TO HEATING. THE PARTS SHALL BE HEATED BY THE USE OF RADIANT HEAT TECHNIQUES SUCH AS THERMAL BLANKETS, INFRARED LAMPS ETC., TO NO MORE THAN A MAXIMUM TEMPERATURE OF 250 F. TEMPERATURE MEASURING DEVICES SHALL BE USED TO MONITOR HEAT AND SHALL BE LOCATED ON AREAS OF THE PART EXPECTED TO REACH MAXIMUM TEMPERATURE. NO SCALING, OXIDATION OR

CORROSION SHALL BE PERMITTED.

COR-BAN 27L (ZIP-CHEM ZC-027L), HEREAFTER REFERRED TO AS CORROSION INHIBITING COMPOUND, PER BMS 3-38 (BOEING CAGE 81205), MANUFACTURED BY ZIP-CHEM PRODUCTS, 400 JARVIS DR., MORGAN HILL, CA 95037

(CAGE 8E913), SHALL BE USED AS NOTED.

BUSHINGS WITHOUT FLANGES SHALL BE INSTALLED INTO HOUSING BORE WHICH HAS RECEIVED A LIGHT COAT OF CORROSION INHIBITING COMPOUND. CORROSION INHIBITING COMPOUND SHALL NOT OBSTRUCT GREASE ZERK PASSAGES. INSTALL SHRUNKEN BUSHING AND WIPE OFF ANY EXCESS COMPOUND THAT MAY HAVE EXTRUDED

AROUND THE PERIPHERY OF BOTH ENDS OF THE BUSHINGS.

BUSHING WITH FLANGES SHALL BE INSTALLED IN A SIMILAR MANNER AS PARAGRAPH (G), EXCEPT CORROSION- INHIBITING COMPOUND SHALL ALSO BE APPLIED TO FACE OF LUG UNDER FLANGE. THE COMPOUND SHALL BE APPLIED IN SUCH A MANNER AS TO ENSURE COMPLETE COVERAGE OF INSIDE FACE OF BUSHING FLANGE WHEN BUSHING IS INSTALLED. WIPE OFF ANY EXCESS COMPOUND AROUND PERIPHERY OF BUSHING FLANGE FORMING A

BEAD. WIPE ANY EXCESS COMPOUND FROM OTHER END OF BUSHING ALSO.

13. INSTALL FASTENERS USE WET SEALANT PER BMS5-95 IN LIEU OF F-19.48.

15. PRIMER PER MIL-PRF-23377, TYPE 1 CLASS C2 IN LIEU OF BMS10-11 OR F-20.02.

16. CHROMIC ACID ANODIZE PER MIL-A-8625, TYPE I, CLASS 1 IN LIEU OF F-17.05.

17. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE I, METHOD B, C OR D, LEVEL 3 OR 4 IN LIEU OF BAC5423. THE FOLLOWING ACCEPTANCE/REJECTION CRITERIA MAY BE USED AS AN ALTERNATE TO THE ORIGINAL MANUFACTURER CRITERIA: NO RELEVANT INDICATIONS ALLOWED. THE INTENT OF NO RELEVANT INDICATIONS ALLOWED IS THAT THE INSPECTION IS CONDUCTED AT THE REQUIRED SENSITIVITY LEVEL AND THERE

HILL AFB FORM 462 Page 3 of 5

SHALL BE NO DEFECTS ALLOWED. THE INSPECTOR PERFORMING THE INSPECTION SHALL BE CERTIFIED TO LEVEL II WITH THE INSPECTION PROCEDURE DEVELOPED BY A LEVEL III AS SPECIFIED IN AIA/NAS-410.

18. APPLY ONE COAT OF POLYURETHANE PAINT PER MIL-PRF-85285, TYPE I, COLOR NUMBER 17038 (BLACK) PER

FED-STD-595, IN LIEU OF SRF-14.9815-17038.

19. APPLY ONE COAT OF POLYURETHANE PAINT PER MIL-PRF-85285, TYPE I, COLOR NUMBER 17925 (WHITE) PER

FED-STD-595, IN LIEU OF SRF-14.9815-17886.

20. PART MARKING INSTRUCTIONS CONTROLLED BY DRAWING, DRAWING CONTAINS ALL

MARKING INSTRUCTIONS IN LIEU OF C.

21. PART MARKING USING RUBBER STAMP, INKJET MARKING, OR STENCIL IN LIEU OF M.

DETAIL OR SUB-ASSEMBLY IDENTIFICATION AFTER INSTALLATION OF ASSEMBLY

OPERATIONS IS OPTIONAL.

22. D6-5000 AND DAA8712V002 ARE NOT REQUIRED FOR MANUFACTURE AND WILL NOT BE PROVIDED.

23. BREAK SHARP EDGES 0.005 – 0.015 NO BURRS ALLOWED IN LIEU OF BAC5300.

24. HEAT TREAT ALUMINUM ALLOY PER SAE AMS 2770 IN LIEU OF BAC 5602.

25. SURFACE ROUGHNESS PER ASME B46.1 IN LIEU OF ANSI B46.1 OR BACD2097.

26. DRAWING DAA3222D153 FORGING-TOW FITTING

27. PART MARKING INSTRUCTIONS CONTROLLED BY DRAWING, DRAWING CONTAINS ALL

MARKING INSTRUCTIONS IN LIEU OF C.

28. ALUMINUM FORGING PROCESS PER SAE AMS-A-22771 IN LIEU OF BMS7-214.

29. APPLY NO FINISH, EXCEPT TEMPORARY PROTECTION PER MIL-PRF-16173, GRADE 1 IN LIEU OF F-25.01.

30. HEAT TREAT PER SAE AMS 2772 IN LIEU OF BAC5602.

31. D6-5000 AND D583-21003 ARE NOT REQUIRED FOR MANUFACTURE AND WILL NOT BE PROVIDED.

32. THE CONTRACTOR MAY PROCURE FORGINGS FROM SOURCES PRE-APPROVED BY LANDING GEAR ENGINEERING PER PARAGRAPH (A), OR MAY ELECT TO DEVELOP SOURCES PER PARAGRAPH (B).

(A) IF FORGINGS ARE PROCURED FROM TOOLING APPROVED BY OO-ALC LANDING GEAR ENGINEERING, ORIGINAL CERTIFIED FORGING PROCEDURES AND DIES/TOOLING OR EQUIVALENT (E.G., REFURBISHED/RESUNK BY APPROVED FORGING SOURCE AND HAVING THE SAME DIE NUMBER DESIGNATION) SHALL BE USED. NEW TOOLING AT AN EXISTING SOURCE WILL BE QUALIFIED PER PARAGRAPH (B). PRIOR TO CONTRACT AWARD, THE DETAILED PART BIDDER SHALL PROVIDE VERIFICATION (E.G., FORGING QUOTE) TO THE GOVERNMENT THAT THE CERTIFIED DIES AND PROCEDURES ARE AVAILABLE FOR THEIR USE IN THE EVENT THEY ARE THE SUCCESSFUL BIDDER.

1. FORGING DRAWING: DAA3222D153

2. CONTROL OF FORGING PROCESS: USAF

HILL AFB FORM 462 Page 4 of 5

3. DIE #: UNKNOWN

4. LOCATION OF FORGING DIES: UNKNOWN

5. PHONE: UNKNOWN

6. CAGE: UNKNOWN

(B) IF THE FORGING SOURCE IS LISTED AS UNKNOWN OR THE CONTRACTOR WISHES TO DEVELOP ADDITIONAL SOURCES OR NEW TOOLING AT AN EXISTING FORGING SOURCE, THE CONTRACTOR SHALL ADVISE THE GOVERNMENT IN WRITING OF THEIR INTENT TO PROCURE NEW FORGING DIES AND THE PROPOSED FORGING SOURCE PRIOR TO CONTRACT AWARD. THE CONTRACTOR SHALL NOT PROCEED TO OBTAIN NEW DIES WITHOUT THE EXPRESS CONSENT OF THE GOVERNMENT-PROCURING AGENCY (SEE OO-ALC LANDING GEAR ENGINEERING FORGING SQS FOR FURTHER INFORMATION ON FORGING TOOLING QUALIFICATION REQUIREMENTS). THE GOVERNMENT SHALL HAVE UNLIMITED USE OF THE DIES DEVELOPED UNDER THIS CONTRACT. THE CONTRACTOR SHALL INFORM THE FORGING HOUSE IN WRITING, AT THE SAME TIME THE ORDER FOR THE DIES IS PLACED, THAT THE GOVERNMENT HAS UNLIMITED USE RIGHTS OF THE DIES AND FORWARD A COPY OF THIS LETTER TO THE

GOVERNMENT CONTRACTING OFFICER.

PRIOR TO PRODUCTION, FORGING LOT QUALIFICATION SHALL BE ACCOMPLISHED AS SPECIFIED ON THE FORGING DRAWING AND SAE AMS-F-7190 FOR STEEL FORGINGS AND SAE AMS-A-22771 FOR ALUMINUM FORGINGS.

THE DETAILED PART CONTRACTOR SHALL ASSURE THAT THIS HAS BEEN ACCOMPLISHED BY THE FORGING SOURCE AND RETAIN IN THEIR RECORDS FOR NO LESS THAN 10 YEARS. LANDING GEAR ENGINEERING RESERVES

THE RIGHT TO REVIEW THIS DOCUMENTATION AS NEEDED.

33. DRAWING DAA3222D168 AXLE FITTING-MAIN LANDING GEAR

34. USE ALUMINUM-NICKEL-BRONZE MATERIAL TO MEET DRAWING REQUIREMENTS PER SAE AMS 4640 IN LIEU OF

AMS 4640.

35. USE ALUMINUM-BRONZE ALLOY CENTRIFUGAL CAST MATERIAL TO MEET DRAWING REQUIREMENTS PER SAE

AMS 4880 IN LIEU OF AMS 4880.

36. BREAK SHARP EDGES 0.005 - 0.015 NO BURRS ALLOWED IN LIEU OF BAC5300.

37. SURFACE TEXTURE PER ASME B46.1 IN LIEU OF ANSI B46.1 AND BACD2097.

38. PERFORM FLUORESCENT PENETRANT INSPECTION PER ASTM E 1417 TYPE I, METHOD B, C OR D, LEVEL 3 OR 4 IN LIEU OF BAC 5423 WITH THE FOLLOWING ACCEPTANCE/REJECTION CRITERIA: NO RELEVANT DEFECTS ALLOWED. THE INTENT OF NO RELEVANT DEFECTS ALLOWED IS THAT THE INSPECTION IS CONDUCTED AT THE REQUIRED SENSITIVITY LEVEL AND THERE SHALL BE NO RELEVANT INDICATIONS ALLOWED. THE INSPECTOR PERFORMING THE INSPECTION SHALL BE CERTIFIED TO LEVEL II WITH THE INSPECTION PROCEDURE DEVELOPED

BY A LEVEL III AS SPECIFIED IN AIA/NAS NAS 410.

39. CADMIUM PLATE PER SAE AMS-QQ-P-416, CLASS 2, TYPE II IN LIEU OF F-15.06.

40. THREADS PER SAE AS8879 IN LIEU OF MIL-S-8879.

41. D6-5000 IS NOT REQUIRED FOR MANUFACTURE AND WILL NOT BE PROVIDED.

HILL AFB FORM 462 Page 5 of 5

42. RUBBER STAMP OR INK JET MARK WITH AN OVERCOAT RESISTANT TO ABRASION,

FUEL, AND HYDRAULIC FLUID IN LIEU OF RY.

43. DRAWING DAA3222D400-115

44. BREAK SHARP EDGES 0.005 – 0.015 NO BURRS ALLOWED IN LIEU OF BAC5300.

45. CADMIUM PLATE PER SAE AMS-QQ-P-416, CLASS 2, TYPE II IN LIEU OF F-15.06.

46. RUBBER STAMP OR INK JET MARK WITH AN OVERCOAT RESISTANT TO ABRASION,

FUEL, AND HYDRAULIC FLUID IN LIEU OF RY.

47. APPLY NO FINISH, EXCEPT TEMPORARY PROTECTION PER MIL-PRF-16173, GRADE 1 IN

LIEU OF F-25.01.

48. PERFORM FLUORESCENT PENETRANT INSPECTION PER ASTM E 1417 TYPE I, METHOD B, C OR D, LEVEL 3 OR 4 IN LIEU OF BAC 5423 WITH THE FOLLOWING ACCEPTANCE/REJECTION CRITERIA: NO RELEVANT DEFECTS ALLOWED. THE INTENT OF NO RELEVANT DEFECTS ALLOWED IS THAT THE INSPECTION IS CONDUCTED AT THE REQUIRED SENSITIVITY LEVEL AND THERE SHALL BE NO RELEVANT INDICATIONS ALLOWED. THE INSPECTOR PERFORMING THE INSPECTION SHALL BE CERTIFIED TO LEVEL II WITH THE INSPECTION PROCEDURE DEVELOPED

BY A LEVEL III AS SPECIFIED IN AIA/NAS NAS 410.

49. D6-5000 IS NOT REQUIRED FOR MANUFACTURE AND WILL NOT BE PROVIDED.

50. SURFACE ROUGHNESS PER ASME B46.1 IN LIEU OF ANSI B46.1 OR BACD2097.

51. DRAWING DAA3221D004 – SEALING CONTROL-LANDING GEAR MAIN AND NOSE

52. PER NOTE 2, OPTIONAL NOTE 2 AND NOTE 5: SOLVENT CLEAN WITH A-A-59281 PER MIL-DTL-55441 TO MEET

DRAWING REQUIREMENTS IN LIEU OF BAC5750.

53. PER NOTE 3, OPTIONAL NOTE 3 AND NOTE 6: APPLY MIL-PRF-81733 TYPE II-1/2 CLASS 1 GRADE A IN LIEU OF BMS5-95 SEALANT TO MEET DRAWING REQUIREMENTS PER MIL-PRF-81733 IN LIEU OF BAC5000. DOCUMENTS BMS5-

95 AND BAC5000 WILL NOT BE PROVIDED.

54. PER NOTE 4 IN LIEU OF SRF-14.9815-17886 – APPLY ONE COAT POLYURETHANE PAINT PER MIL-PRF-85285 TYPE 1 CLASS H COLOR NUMBER 17925 (WHITE) PER FED-STD-595 IN LIEU OF FINISH CODE SRF-14.9815 COLOR 17886 (BONE WHITE). DOCUMENT D6-5000 IS NOT REQUIRED FOR MANUFACTURE AND WILL NOT BE PROVIDED.

406 SCMS/GULAA-Hill October 1, 2015

Statement Of Work (SOW) for Packaging & Preservation

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions The contractor shall use the public ASSIST Quick Search website to access specification, standards, data item descriptions documents listed in this contract solicitation:

http://quicksearch.dla.mil

PRESERVATION, PACKAGING & MARKING REQUIREMENTS

The contractor shall develop, implement and maintain the preservation, packaging and packing of all items to be delivered under the terms of this contract. Packaging procedures will be established in accordance with AFMCI 24- 201, specifically Paragraph 3.7 and MIL-STD-2073-1, Standard Practice for Military Packaging (current revision);

Packaging requirements are identified in the AFMC Form 158, Packaging Requirements submitted by the responsible packaging specialist. All “markings and labeling” of shipments shall conform to MIL-STD 129, DoD Standard Practice, Military Marking for Shipment and Storage (current revision)

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM NO. 15)

REQUIREMENTS

The contractor shall use the wood packaging material regulation for international trade which describes phytosanitary (including treatments) that have been approved for wood packaging material and provides for the approval of new or revised treatments. Use the latest revision of (ISPM No. 15), and the following statement complies with the United Nations-implemented restrictions on wood packaging material (WPM). “This requirement is specifically concerned with invasive species such as pinewood nematode. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frames, and cleats. The statement below cites the requirements in detail and covers lumber for building containers and pallets used for deliveries resulting in worldwide shipments (direct vendor deliveries, Air Logistics complex (ALC), Container Consolidation Points (CCP), Aerial Ports, Water Ports, or other DoD installations.):

ELECTROSTATIC MATERIAL (When Applicable) The Contractor shall apply provisions of MIL-STD-1686 (current revision) when identifying all solid state devices and modules containing diodes, translators, integrated circuits and/or other microelectronic components sensitive to electrostatic forces. All such items shall be packaged IAW MIL_STD 2073-1 using electrostatic free barrier materials and shall clearly bear “Electrostatic Sensitive Device” labels IAW MIL-STD 129, Department of Defense Standard Practice Military Marking for Shipment and Storage.

REUSABLE CONTAINERS

The contractor shall safeguard all received reusable shipping containers that meet the requirements of the AFMC Form 158 and are suitable for return shipment of serviceable assets. The contractor shall dispose of and replace unserviceable containers with new containers that meet requirements of the AFMC Form 158. Contact the Administering Contracting Office (ACO) for disposition and replacement when Long Life Reusable Containers (LLRC) are received in an unserviceable condition.

SOW for Packaging & Preservation Standards (Cont.) October 1, 2015

REPORTING DISCREPANCIES

The contractor shall use Web Supply Discrepancy Report (WebSDR) to submit/reply to an Supply Discrepancy Report (SDR), when improperly packed assets are received/shipped in other than the contracted packaging requirements (coded data or Special Packaging Instructions (SPI) drawings) from Department of Defense (DoD) components/ or contractor activities.

The contractor shall request for a WebSDR account via the following URL:

https://www.transactionservices.dla.mil/daashome

(See Defense Logistics Management (DLM) 4000.25-M, Volume 2, Supply Standard and Procedures, Chapter 17, Supply Discrepancy Reporting, http://www2.dla.mil/j-6/dlmso/elibrary/manuals/dlm/dlm_pubs.asp ).

Exceptions when no damage has occurred are as follows:

- Items packaged before the current SPI date.

- An alternate pack may be used, provided the prime Air Force Sustainment Complex, Packaging office at the Air Logistics Complex (ALC) approves and issues a waiver, deviation number, which would be annotated on the exterior container on the lower right hand portion of the identification side of the container.

- In accordance with Technical Order (T.O.) 00-85B-3, How to Package Air Force Spares, the contractor may substitute the next larger size fast pack, of the type I or type II to ship transportation priorities 1 and 2 shipments as long as there is no decrease in any of the container dimensions without the requirement of a waiver deviation. T.O.

00-85-3, can be access via the website: http://www.tinker.af.mil/shared/media/document/AFD-061220-059.pdf

HAZARDOUS MATERIALS (When Applicable) The contractor shall ensure Hazardous shipments comply with International Civil Aviation Organization (ICAO), U.S.

Code of Federal Regulations (CFR) Title 49, International Air Transport Association (IATA) Dangerous Goods Regulation, International Maritime Dangerous Goods Code (IMDG, Annex 1), and AFMAN24-204_IP, Preparing Hazardous Materials for Military Air Shipments. Packaging shall meet “DOT specification or a United Nation (UN) specification ” manufactured in accordance with 49 CFR, Part 178 and the final packages assembled IAW 49 CFR, Parts 100-185 as applicable. A Competent Authority Approval (CAA) shall be acquired from the responsible Associate Administrator or other designated Department official to perform a function requiring prior consent under the Hazardous Material Regulation (HMR). Packages(s) shall be marked IAW MIL-STD-129, DoD Standard Practice, and Military Marking for Shipment and Storage. If a symbol is used to represent the manufacturer or the approval agency certifying compliance with 49 CFR 178, subparts L and M, the symbol must be registered with the U.S. Department of Transportation. A copy of the Contractor’s Test Report and signed certification that the package configuration meets both CFR and UN requirements shall be made available to the procuring contract office, as required, prior to acceptance or shipment of any portion of the product IAW Contract Data Requirements List (CDRL) (Reference AFMC Form 158). Safety Data Sheets (SDS) are required for known hazardous items and applicable items shown in FED-STD-313, Tables I and II. The SDS shall have any applicable identification number, such as National Stock Number or Special Item Number. A copy of the SDS shall be mailed or e-mailed no later than “FIVE” days prior to contractual delivery of items:

AFMC AFMC

406 SCMS/GULAA AFLCMC/LZSA

Attn: Nancy Coronado Attn: Tonita Davis/DSN 785-7901 Packaging Specialist PHS&T POC E-mail: nancy.coronado E-mail: Tonita.davis@us.af.mil

DSN: 777-4514

https://www.transactionservices.dla.mil/daashome http://www2.dla.mil/j-6/dlmso/elibrary/manuals/dlm/dlm_pubs.asp http://www.tinker.af.mil/shared/media/document/AFD-061220-059.pdf mailto:Tonita.davis@us.af.mil

SOW for Packaging & Preservation (Cont) October 1, 2015

APPLICABLE GOVERNMENT PACKAGING DOCUMENTS

NOTE: “UTILIZE THE MOST RECENT POLICY”

AFI 24-203, Preparation and Movement of Air Force Cargo

AFMAN 24-204_IP, Preparing Hazardous Materials for Military Air Shipments

AFMCI 24-201, AFMC Packaging and Materials, Handling Policies and Procedures

DLMS 4000.25-M, Defense Logistics Management Systems (DLMS), Volume 2, Supply Standards and Procedures, Chapter 17, Supply Discrepancy Reporting

DoD 4140.01-M-1, Compliance for Defense Packaging: Phytosanitary Requirements for Wood Packaging Material (WPM)

DOT Title 29, Occupational Safety and Health Administration, Labor

DOT Title 49, Code of Federal Regulations (49 CFR), Transportation

International Civil Aviation Organization (ICAO) Technical Instructions

International Air Transport Association (IATA) Dangerous Goods Regulation

International Maritime Dangerous Goods (IMDG) Code

ISPM No. 15, International Standard Phytosanitary Measure Note: Marking Requirements can be found in the American standards committee, incorporated wood packaging material enforcement regulations dated November 11, 2005 and IPSM 15 No. 15.

MIL-STD-2073-1, Standard Practice, for Military Packaging

MIL-STD-129, Department of Defense Standard Practice Military Marking for Shipment and Storage

406 SCMS/GULAA-Hill October 1, 2015

Statement Of Work (SOW) for Packaging & Preservation

ASSIST Documents for Specifications Listed in the GSA Index of Federal Specifications, Standards and Commercial Item Descriptions

The contractor shall use the public ASSIST Quick Search website to access specification, standards, data item descriptions documents listed in this contract solicitation:

http://quicksearch.dla.mil

PRESERVATION, PACKAGING & MARKING REQUIREMENTS

INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM NO. 15) REQUIREMENTS

ELECTROSTATIC MATERIAL (When Applicable)

The Contractor shall apply provisions of MIL-STD-1686 (current revision) when identifying all solid state devices and modules containing diodes, translators, integrated circuits and/or other microelectronic components sensitive to electrostatic forces...

REUSABLE CONTAINERS

SOW for Packaging & Preservation Standards (Cont.) October 1, 2015

REPORTING DISCREPANCIES

The contractor shall request for a WebSDR account via the following URL: https://www.transactionservices.dla.mil/daashome

Exceptions when no damage has occurred are as follows:

- Items packaged before the current SPI date.

HAZARDOUS MATERIALS (When Applicable)

The contractor shall ensure Hazardous shipments comply with International Civil Aviation Organization (ICAO), U.S. Code of Federal Regulations (CFR) Title 49, International Air Transport Association (IATA) Dangerous Goods Regulation, International Mar...

406 SCMS/GULAA AFLCMC/LZSA

Attn: Nancy Coronado Attn: Tonita Davis/DSN 785-7901

Packaging Specialist PHS&T POC