Special Packaging Instruction (SPI) AK14112137.pdf

DD FORM 2169, JUN 1997 PREVIOUS EDITIONS ARE OBSOLETE Page 1 of 3 Pages

17. NOTES/ DRAWING

A. PRESERVATION AND PACKAGING SHALL BE INSPECTED IN ACCORDANCE WITH MIL-STD-2073-1 AND ANY

APPLICABLE CONTAINER SPECIFIATIONS.

B. FLUSH OR SLUSH INTERNALLY AND DRAIN EXCESS, THEN APPLY TO ALL EXTERIOR METALLIC SURFACES

C. FABRICATE CONTAINER BASE "C" USING 3/4-INCH THICK A-A-55057 PLYWOOD, TYPE A, EXPOSURE 1, 48/24 SPAN

RATING, GRADE CDX, SIZE 16 X 28-INCHES. FABRICATE BLOCKING AND SKIDS USING MIL-STD-731, GROUP II

LUMBER AS SHOWN IN SKETCHES ON PAGES 2 AND 3. SECURE SKIDS TO BASE USING FF-N-105 NUMBER 6 NAILS.

SECURE BLOCKING TO BASE USING FF-N-105 NUMBER 12 NAILS.

D. CENTER PADS 'D" ON BASE 'C" USING BASE 'C" AS A TEMPLATE, LOCATE AND FABRICATE FOOR HOLES.

E. ENVELOPE "E" SHALL BE FABRICATED FROM A 35 X 36-INCH SHEET. GASKETED HOLES SHALL BE IN ACCORDANCE WITH MlL-E-6060. CENTER ENVELOPE "E" ON BASE "C" USING BASE "C" AS A TEMPLATE, LOCATE AND FABRICATE FOUR HOLES AS SHOWN IN SKETCH ON PAGE 3. SECURE CYLINDER HEAD ASSEMBLY TO BASE "C" WITH FOUR

CARRIAGE BOLTS 1/2 X 4-1/2-INCH AND APPROPRIATE NUTS AND LOCKWASHERS.

F. SECURE WRAP USING TAPE.

G. CONTAINER SHALL BE MODIFIED AS FOLLOWS: HOOD SHALL BE FABRICATED USING 1-INCH NOMINAL LUMBER, AND SHALL BE MADE TO FIT OVER CONTAINER BASE RESTING ON SKIDS. SECURE HOOD TO BASE USING FF-S-111 SCR

OF THE APPROPRIATE SIZE.

H. IN ADDITION TO MIL-STD-129 MARKINGS THE UNIT CONTAINER SHALL BE MARKED ON THE TOP AND ONE SIDE WITH 1/2 INCH HIGH (MIN.) BLACK LETTERS "REUSABLE CONTAINER AND CUSHIONING, DO NOT DESTROY", IN ADDITION, TOP SHALL BE MARKED WITH 1/2 INCH HIGH (MIN.) LETTERS "REMOVE SCREWS TO OPEN CONTAINER".

I. THE UNIT CONTAINER IS THE SHIPPING CONTAINER

Item Dimensions (IN) 20.5 X 8.4 X 5.1 Item Weight 62.0.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

-DT

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number

PLEASE DO NOT RETURN YOUR COMPLETED FORM TO THE ABOVE ORGANIZATION.

1. PART OR DRAWING NO. (CAGE) NOMENCLATURE 2. CAGE 3. SPI NO.

10163726 (11862) CYLINDER HEAD ASSEMBLY 19207 AK14112137

4. NATIONAL STOCK NO. 5. DATE 6. REVISION

2815-01-411-2137 23 APR 2024 A

7. QUP 8. ICQ 9. UNIT PACK WT (LB.) 10. UNIT PACK CU (CU. FT.) 11. UNIT PACK SIZE (INCHES)

001 000 90.0 3.009 31.1 X 17.6 X 9.5

12. MILITARY PRESERVATION 18.

STEPS

19.

REQD

20.

DESCRIPTION MIL-STD-2073-1, METHOD 43

13. CLEANING 1B A/R PRESERVATIVE: MIL-PRF-21260, GR. 10

MIL-STD-2073-1 2C 1 CONTAINER BASE: SEE NOTE C

14. DRYING 3D 1 CUSHIONING: PPP-C-1797, TYPE I, 24 X 12 X 1/4

MIL-STD-2073-1 4E 1 ENVELOPE: MIL-E-6060, SIZE: 20 X 36

15. PACKING 5F 1 WRAP: MIL-PRF-121, TY I, SIZE: 29 X 28

6G 1 CONTAINER: ASTM-D6880 (MOD), CL. 2, ST. 4,

a. LEVEL A SIZE: 28-1/8 X 16-1/8 X 6-3/4

MIL-STD-2073-1 AND NOTE I

b. LEVEL B

NOT APPLICABLE

16. MARKING

MIL-STD-129 ANMD NOTE H

SPECIAL PACKAGING INSTRUCTION (Continuation Sheet) Form Approved

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number

PLEASE DO NOT RETURN YOUR COMPLETED FORM TO THE ABOVE ORGANIZATION.

1. PART OR DRAWING NO. (CAGE) NOMENCLATURE 2. CAGE 3. SPI NO.

10163726 (11862) CYLINDER HEAD ASSEMBLY 19207 AK14112137

4. NATIONAL STOCK NO.

2815-01-411-2137

5. DATE

23 APR 2024

6. REVISION

A

DD FORM 2169C, JUN 1997 (EG) WCT 9-99 PREVIOUS EDITIONS ARE OBSOLETE Page 2 of 3 Pages

SPECIAL PACKAGING INSTRUCTION (Continuation Sheet) Form Approved

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services Directorate (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number

PLEASE DO NOT RETURN YOUR COMPLETED FORM TO THE ABOVE ORGANIZATION.

1. PART OR DRAWING NO. (CAGE) NOMENCLATURE 2. CAGE 3. SPI NO.

10163726 (11862) CYLINDER HEAD ASSEMBLY 19207 AK14112137

4. NATIONAL STOCK NO.

2815-01-411-2137

5. DATE

23 APR 2024

6. REVISION

A

DD FORM 2169C, JUN 1997 (EG) WCT 9-99 PREVIOUS EDITIONS ARE OBSOLETE Page 3 of 3 Pages