Attachment_0002_Special_Packaging_AG00000655.pdf

SPECIAL PACKAGING INSTRUCTION

Form Approved

OMB No. 0704-0188

1. PART OR DRAWING NO.

LASER DETECTING SETS

2. CODE IDENT

80063

3. SPI NO.

AG00000655

4. NATIONAL STOCK NO

MULTIPLE – See Note 4

5. DATE OF DRAWING

15096

6. REVISION

7. QUP

8. ICQ

9.UNIT PACK WEIGHT 10.UNIT PACK CUBE 11.UNIT PACK SIZE

12. PRESERVATION 18.

STEPS

19.

REQD

20.

DESCRIPTION

MILITARY

Note 1 N/A N/A N/A

13. CLEANING

MIL-STD-2073-1

APPLICABLE DOCUMENTS

DDSFSDFDF

14. DRYING

MIL-STD-2073-1

MIL-STD-129

MIL-STD-2073-1

15. PACKING MIL-DTL-117

MIL-PRF-26514

a. LEVEL A

Note 2.1

PPP-C-795

ASTM D1974

b. LEVEL B

Note 2.2

ASTM D5118

ASTM D5486

16. MARKING

MIL-STD-129

ISPM 15

17. NOTES

1. PRESERVATION. MIL-STD-2073-1 as specified herein, ensuring compliance with the applicable requirements of that standard.

1.1 Laser Detecting Sets – AN/AVR-2B(V)1 and AN/AVR-2B(V)2. Each sensor unit and comparator will be individually packaged.

1.1.1 Sensor Unit – SU-130B. Unit pack each as follows: Place protective cap onto J1 connector. Cushion sensor unit with

PPP-C-795, Class 2. Place cushioned sensor unit into a heat-sealed bag conforming to MIL-DTL-117, Type I, Class F, Style

1. Wrap bagged sensor unit with cushioning material meeting the requirements of PPP-C-795, Class 1. Secure cushioning with tape conforming to ASTM D5486, Type V or any substitute. Fully encapsulate the bubble-wrapped sensor unit with two inches of cushioning in conformance with the requirements of MIL-PRF-26514, Type I, Class 2, Grade A inside of an ASTM

D5118, Grade V3c or W5c fiberboard box. Close and seal the box in accordance with ASTM D1974.

1.1.2 Comparator – CM-493B. Unit pack each as follows: Place protective caps on connectors J1 through J9. Disconnect security key from comparator without disconnecting the lanyard from the security key and the comparator. Place the security key in a bag conforming to MIL-DTL-117, Type I, Class F, Style 1. Wrap the bagged key with cushioning material meeting the requirements of PPP-C-1795, Class 2, ensuring that the lanyard is not disconnected from the security key or comparator.

Place the wrapped and bagged security key on top of the comparator ensuring the lanyard remains connected to the security key and the comparator. Wrap the entire comparator with PPP-C-795, Class 2 cushioning. Place the cushioned comparator into a heat-sealed bag conforming to MIL-DTL-117, Type I, Class F, Style 1. Wrap bagged sensor unit with cushioning material meeting the requirements of PPP-C-795, Class 1. Secure cushioning with tape conforming to ASTM D5486, Type V or any substitute. Fully encapsulate the bubble-wrapped sensor unit with two inches of cushioning in conformance with the requirements of MIL-PRF-26514, Type I, Class 2, Grade A inside of an ASTM D5118, Grade V3c or W5c fiberboard box.

Close and seal the box in accordance with ASTM D1974.

DA FORM 2169, JUN 86

SPECIAL PACKAGING INSTRUCTION

(Continuation Sheet )

Form Approved

OMB No. 0704-0188

1. PART OR DRAWING NO.

LASER DETECTING SETS

2. CODE IDENT

80063

3. SPI NO.

AG00000655

4. NATIONAL STOCK NO

MULTIPLE – See Note 4

5. DATE

15096

6. REVISION

2. PACKING.

2.1 Level A.

2.1.1 Laser Detecting Set – AN/AVR-2B(V)1. Consists of one comparator and four sensor units. Consolidate unit packs described in paragraphs 1.1.1 and 1.1.2 in an appropriately sized container identified in MIL-STD-2073-1, Table C-II.

2.1.2 Laser Detecting Set – AN/AVR-2B(V)2. Consists of one comparator and six sensor units. Consolidate unit packs described in paragraphs 1.1.1 and 1.1.2 in an appropriately sized container identified in MIL-STD-2073-1, Table C-II.

2.1.3 Sensor Unit – SU-130B. Place unit pack(s) described in paragraph 1.1.1 in an appropriately sized container identified in MIL-STD-2073-1, Table C-II.

2.1.4 Comparator – CM-439B. Place unit pack(s) described in paragraph 1.1.2 in an appropriately sized container identified in MIL-STD-2073-1, Table C-II.

2.2 Level B.

2.2.1 Laser Detecting Set – AN/AVR-2B(V)1. Consists of one comparator and four sensor units. The unit packs described in paragraphs 1.1.1 and 1.1.2 can also serve as the shipping containers, or consolidate in an appropriately sized container identified in MIL-STD-2073-1, Table C-II.

2.2.2 Laser Detecting Set – AN/AVR-2B(V)2. Consists of one comparator and six sensor units. The unit packs described in paragraphs 1.1.1 and 1.1.2 can also serve as the shipping containers, or consolidate in an appropriately sized container

2.2.3 Sensor Unit – SU-130B. The unit pack described in paragraph 1.1.1 can also serve as the shipping container. If a quantity of sensor units are being packed and shipped to the same location, consolidate in an appropriately sized container

2.2.4 Comparator – CM-439B. The unit pack described in paragraph 1.1.2 can also serve as the shipping container. If a quantity of comparators are being packed and shipped to the same location, consolidate in an appropriately sized container

3. Requirements for Wood Packaging Materiel. All CONUS and OCONUS shipments utilizing wood packaging material, such as pallets, dunnage, crating, packing blocks, drum, cases, load boards, pallet collars, and skids, shall meet the

International Standards for Phystosanitary Measures, ISPM 15, entitled “Regulation of Wood Packaging Material in

International Trade”.

4. National Stock Numbers. The following NSNs are associated with this Special Packaging Instruction:

AN/AVR-2B(V)1: 5865-01-515-0444

AN/AVR-2B(V)2: 5865-01-515-0458

CM-493B: 5865-01-514-2857

SU-130B: 5865-01-511-8345

DA FORM 2169C, JUN 86 Page 2 of 2