SPMYM2-24-P-1933 (ADDITIONAL ORDERING DATA) HOSES - CLINS 0001-0009.pdf

C:\Users\JOHN~1.IVE\AppData\Local\Temp\MicrosoftEdgeDownloads\f07a011b-77ba-4d9a-aadd-0ea3a6299586\1.0IN x 25FT Potable Water Hose Assembly.docx Last revised 5/26/2009 fwv

CONTRACT ITEM DESCRIPTION: 1" POTABLE WATER SUPPLY HOSE ASSEMBLY

( 1 ” I . D . X 2 5 ’ L O N G )

FULLY ASSEMBLED HOSE DESIGNED TO HANDLE WATER SUITABLE FOR DRINKING.

TO BE USED IN POTABLE WATER SERVICES.

Nomenclature: 1) GOODYEAR,

2) UNISOURCE, POTABLE WATER HOSE, Part # 2765-100-050 Or Equal

Or Equal Purchase Specification:

Hose, Nonmetallic, Multiple Plies of tube, reinforcement and cover: The Inner Tube to be made of White Chlorobutyl Rubber. The Reinforcement to be Synthetic textile fabric piles with Monofilament Helix, NO METAL HELICAL WIRE REINFORCEMENT. The outer cover may be SBR or EPDM cloth wrapped impression. Hoses to be coupled and fully assembled using PT Coupling Company, Bronze Cam & Grove end fittings and Stainless Steel Interlocking Ferrules.

Description:

1. Size: I" I.D. by 25’ Long.

2. Nominal OD: 1.50”

3. Application: Temporary Service, Potable Water transfer systems on piers, dry docks and within ship spaces.

4. Expected Working Pressure of Intended Services: 150 PSI.

5. Manufactured Rated Working Pressure: 250 PSI maximum.

6. Burst Pressure: 1,000 PSI minimum.

7. Rated bend radius: N/A

8. Rated Continuous Temperature: -25º F to 180º F minimum.

9. No price quote or bid offer will be accepted without the offerer submitting: hose, fitting, and ferrule manufacturer cut sheets or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The price quote must reference the manufacturer's part numbers for the item quoted.

10. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

11. PSNS & IMF Engineering Code 260.41 must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

12. Tube: White Chlorobutyl Rubber. (Compliant to FDA 3A Standard 18-03 Class III for milk).

13. Cover: SBR or EPDM rubber, cloth wrapped impression. Non-wired or braid, multiple synthetic textile fabric pile construction.

14. Reinforcement: Synthetic textile fabric piles.

15. Cover Color: Blue

16. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories.

Distribution (NAHAD) certification standards.

17. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 1” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 10E, Item # 1200510.

b. 2nd Hose End; Brass, 1” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and

Passive Locking Device, PT Coupling Co., Part # 10CSLII, Item # 1290310L2.

c. End Fitting must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

d. End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., “Pro-Grip C50SS” Stainless

Steel Crimp Ferrules sized to match the hose and fittings.

18. Branding / Marking: Hose shall be continuously ink-branded or Mylar or striped in white or a contrasting color to the blue outer cover of the hose. The lettering shall state as a minimum:

a. Manufacturer Name/Hose Brand/Line/Model number,

b. “Potable” or “Potable Water Hose”

c. Manufacturers rated WP (150 PSI minimum)

Hose Test & Assembly Certification:

After each hose assembly is completed it shall be hydrostatically strength tested with potable water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Manufacturer shall certify that hose assemblies are free of leaks, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are still properly positioned on the hose ends; also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested (100% of hoses) shall be provided with shipped hoses.

C:\Users\JOHN~1.IVE\AppData\Local\Temp\MicrosoftEdgeDownloads\38e0b49d-40e8-4eb8-b02c-1acb8355ef92\1.0 IN x 50 FT Potable Water Hose Assembly Description.docx Last revised 5/26/2009 fwv

CONTRACT ITEM DESCRIPTION: 1" POTABLE WATER SUPPLY HOSE ASSEMBLY

( 1 ” I . D . X 5 0 ’ L O N G )

FULLY ASSEMBLED HOSE DESIGNED TO HANDLE WATER SUITABLE FOR DRINKING.

TO BE USED IN POTABLE WATER SERVICES.

Nomenclature: 1) GOODYEAR,

2) UNISOURCE, POTABLE WATER HOSE, Part # 2765-100-050 Or Equal

Or Equal Purchase Specification:

Hose, Nonmetallic, Multiple Plies of tube, reinforcement and cover: The Inner Tube to be made of White Chlorobutyl Rubber. The Reinforcement to be Synthetic textile fabric piles with Monofilament Helix, NO METAL HELICAL WIRE REINFORCEMENT. The outer cover may be SBR or EPDM cloth wrapped impression. Hoses to be coupled and fully assembled using PT Coupling Company, Bronze Cam & Grove end fittings and Stainless Steel Interlocking Ferrules.

Description:

1. Size: I" I.D. by 50’ Long.

2. Nominal OD: 1.50”

3. Application: Temporary Service, Potable Water transfer systems on piers, dry docks and within ship spaces.

4. Expected Working Pressure of Intended Services: 150 PSI.

5. Manufactured Rated Working Pressure: 250 PSI maximum.

6. Burst Pressure: 1,000 PSI minimum.

7. Rated bend radius: N/A

8. Rated Continuous Temperature: -25º F to 180º F minimum.

9. No price quote or bid offer will be accepted without the offerer submitting: hose, fitting, and ferrule manufacturer cut sheets or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The price quote must reference the manufacturer's part numbers for the item quoted.

10. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

11. PSNS & IMF Engineering Code 260.41 must approve all exceptions and Or-Equal offer’s prior to purchase.

Construction:

12. Tube: White Chlorobutyl Rubber. (Compliant to FDA 3A Standard 18-03 Class III for milk).

13. Cover: SBR or EPDM rubber, cloth wrapped impression. Non-wired or braid, multiple synthetic textile fabric pile construction.

14. Reinforcement: Synthetic textile fabric piles.

15. Cover Color: Blue

16. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories.

Distribution (NAHAD) certification standards.

17. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; Brass, 1” Male Cam & Groove Adapter by Hose Shank, PT Coupling Co., Part # 10E, Item # 1200510.

b. 2nd Hose End; Brass, 1” Female Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and

Passive Locking Device, PT Coupling Co., Part # 10CSLII, Item # 1290310L2.

c. End Fitting must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

d. End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., “Pro-Grip C50SS” Stainless

Steel Crimp Ferrules sized to match the hose and fittings.

18. Branding / Marking: Hose shall be continuously ink-branded or Mylar or striped in white or a contrasting color to the blue outer cover of the hose. The lettering shall state as a minimum:

a. Manufacturer Name/Hose Brand/Line/Model number,

b. “Potable” or “Potable Water Hose”

c. Manufacturers rated WP (150 PSI minimum)

Hose Test & Assembly Certification:

After each hose assembly is completed it shall be hydrostatically strength tested with potable water as a test medium, at 225 (+20, -0) PSIG for 10 minutes. Manufacturer shall certify that hose assemblies are free of leaks, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are still properly positioned on the hose ends; also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested (100% of hoses) shall be provided with shipped hoses.

C:\Users\JOHN~1.IVE\AppData\Local\Temp\MicrosoftEdgeDownloads\81f6c6e3-1f3b-4d7a-90de-e0a98a6b40ac\1.5 IN x 50 FT POTABLE WATER HOSE ASSEMBLY Description.doc Last revised 12/02/2014

CONTRACT ITEM DESCRIPTION: FULLY ASSEMBLED HOSE DESIGNED TO HANDLE WATER

SUITABLE FOR DRINKING. TO BE USED IN SUPPLY AND DISCHARGE OF POTABLE DRINKING WATER SERVICES.

(1-1/2” I.D. X 50’ LONG)

Nomenclature: 1) Continental ContiTech, Plicord Clearwater® Hose

2) Continental ContiTech, Vintner™

3) Unisource Manufacturing, Series 2765 Potable Water Hose, Part # 2765-150-050

4) Premier Industrial Hose Manufacturing, Ltd, Potable Water Discharge Hose

Or Equal

Or Equal Purchase Specification:

Nonmetallic hose assembly, for use in potable water supply/discharge systems, Blue – EPDM or SBR outer cover, white Chlorobutyl Rubber or clear Pliosyn™ (UHMWPE) inner tube. The reinforcement is to be multiple synthetic textile fabric plies, with Monofilament Helix . The outer cover may be EPDM or SBR cloth wrapped impression. Hoses to be coupled and fully assembled with: No Lead Brass, Cam & Grove end fittings and Stainless Steel, Crimp Ferrules.

Description:

1. Size: I-1/2" I.D. by 50’ Long.

2. Nominal OD: 2.30”

3. Application: Temporary Service, Potable Water transfer systems on piers, dry docks and within ship spaces.

4. Expected Working Pressure of Intended Services: 150 PSI.

5. Manufactured Rated Working Pressure: 250 PSI maximum.

6. Burst Pressure: 1,000 PSI minimum.

7. Rated bend radius: N/A

8. Rated Continuous Temperature: -25º F to 220º F minimum.

9. No price quote or bid offer will be accepted without the offer submitting hose, fitting, and ferrule manufacturer cut sheets or product description sheet attachments, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number, and manufacturer’s point of contact.

The price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors if requested must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to approval by PSNS & IMF Engineering Code 270TS for purchase.

11. PSNS & IMF Engineering Code 270TS must approve all exceptions and “Or-Equal” offers prior to purchase.

Construction:

12. Inner Tube: White Chlorobutyl Rubber, FDA/USDA compliant and conforms to 3-A Sanitary Standard 18-03, or Clear Pliosyn™

(UHMWPE).

13. Outer Cover: EPDM Rubber or SBR cloth wrapped impression.

14. Reinforcement: Synthetic textile fabric plies with monofilament helix.

15. Outer Cover Color: Blue.

16. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories

Distribution (NAHAD) certification standards.

17. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End; No Lead Brass, 1-1/2” Cam & Groove Coupler X Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device. PT Coupling Co., Part # 15CSLII-NL, Item # 1290315L2-NL.

a. 2nd Hose End; No Lead Brass, 1-1/2” Cam & Groove Adapter X Hose Shank. PT Coupling Co., Part # 15E-NL, Item # 1200515-NL.

c. End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., ProGrip™ Stainless Steel C50SS Crimp Ferrules sized to match the hose and end fittings.

18. Branding / Marking: Hose shall be continuously ink-branded or Mylar or striped in white or a contrasting color to the blue outer cover of the hose.

The lettering shall state as a minimum:

a. Manufacturer Name/Hose Brand/Line/Model number

b. “Potable Water” or “Potable Water Hose”

c. Manufacturers rated WP (250 PSI maximum)

Hose Test & Assembly Certification:

After each hose assembly is completed it shall be hydrostatically strength tested with commercial clean water as a test medium, at 225 PSIG (+20/-0 PSI) for 10 minutes. Manufacturer shall certify that hose assemblies are free of leaks, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are still properly positioned on the hose ends. Also that the hose does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of

C:\Users\JOHN~1.IVE\AppData\Local\Temp\MicrosoftEdgeDownloads\81f6c6e3-1f3b-4d7a-90de-e0a98a6b40ac\1.5 IN x 50 FT POTABLE WATER HOSE ASSEMBLY Description.doc Last revised 12/02/2014 satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested (100% of hoses) shall be provided with shipped hoses.

CONTRACT ITEM DESCRIPTION: SEAWATER (ASW) or FRESH WATER HOSE ASSEMBLY 1-1/2" I.D. x 25' Long

Nomenclature:

1) Continental ContiTech, IBRS 542060

2) Unisource Manufacturing, Series 2248 “Tuff Skin” Tank Truck Hose – 250 PSI, Part # 2248-250-005

3) HBD Thermoid, Special Oilfield Vacuum Hose 250 PSI

Or Equal.

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Carboxylated Nitrile Cover: Coupled and Fully Assembled.

Application for Intended Use: Will be installed in a marine environment for use in Temporary Services for Shipboard Seawater / Fresh Water Suction/Discharge Services. When not in use, the hose will be coiled and stacked for storage in an area with fluorescent lighting.

1. Size: 1-1/2” I.D. by 25’ long.

2. Nominal OD: 2”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

1. Tube: Extruded Nitrile synthetic rubber. Must meet Association for Rubber Product Manufacturers (ARPM) Class B standard for medium/high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Carboxylated Nitrile Rubber with high abrasion resistance. The cover shall be formulated to provide resistance to UV and weathering adequate to prevent failure due to these causes for a minimum of 10 years when installed and stored described in this specification. ARPM Class A high oil resistance. High ozone resistance.

4. Cover Color: Black Outer Cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End: Brass, 2-1/2” Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device. PT Coupling Company, Part # 25CSLII, Item # 1290325L2.

b. 2nd Hose End: Brass, 2-1/2” Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 25E, Item # 1200525.

c. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., PROGRIP™ C50SS

Stainless Steel Crimp Ferrules. Ferrules to be sized to match the hose and end fittings. No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from virgin brass, meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS & IMF Code 270TS.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked with ½” minimum height lettering in a contrasting color to the Red band strip and Black Outer Cover of the hose.

The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Working Pressure, Date of Manufacture

b. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors, if requested, must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All ”Or-Equal” offers must be approved by PSNS & IMF Temporary Services Engineering, Code 270TS prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each certified hose assembly is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested certification for each hose assembly shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11F, PSNS&IMF 11300.10K, Industrial Process Instruction 0505-904C CH- 2, Codes of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

CONTRACT ITEM DESCRIPTION: SEAWATER (ASW) or FRESH WATER HOSE ASSEMBLY 1-1/2" I.D. x 50' Long

Nomenclature:

1) Continental ContiTech, IBRS 542060

2) Unisource Manufacturing, Series 2248 “Tuff Skin” Tank Truck Hose – 250 PSI, Part # 2248-250-005

3) HBD Thermoid, Special Oilfield Vacuum Hose 250 PSI

Or Equal.

Or-Equal Purchase Specification:

Hose, Nonmetallic, Nitrile Tube & Carboxylated Nitrile Cover: Coupled and Fully Assembled.

Application for Intended Use: Will be installed in a marine environment for use in Temporary Services for Shipboard Seawater / Fresh Water Suction/Discharge Services. When not in use, the hose will be coiled and stacked for storage in an area with fluorescent lighting.

1. Size: 1-1/2” I.D. by 50’ long.

2. Nominal OD: 2”

3. Vacuum: Full

4. Working Pressure: 250 PSI, minimum.

5. Burst Pressure: 1,000 PSI, minimum.

6. Rated bend radius: 10 inches or less.

7. Rated Continuous Temperature: -20ºF to 180ºF

Construction:

1. Tube: Extruded Nitrile synthetic rubber. Must meet Association for Rubber Product Manufacturers (ARPM) Class B standard for medium/high oil resistance. Hose shall be wrapped or mandrel type construction with a heavy enough wall construction to allow the use of crimped or swaged couplings with interlocking ferrules.

2. Reinforcement: Multiple braids of textile fabric with a high-tensile wire helix.

3. Cover: Carboxylated Nitrile Rubber with high abrasion resistance. The cover shall be formulated to provide resistance to UV and weathering adequate to prevent failure due to these causes for a minimum of 10 years when installed and stored described in this specification. ARPM Class A high oil resistance. High ozone resistance.

4. Cover Color: Black Outer Cover with a contrasting Red colored brand strip down the entire lay line with contrasting lettering.

5. Hose end assembly shall be accomplished in accordance with established National Association for Hose Accessories

Distribution (NAHAD) certification standards.

6. Each hose assembly shall have the following components installed at each end:

a. 1st Hose End: Brass, 2-1/2” Cam & Groove Coupler by Hose Shank, with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device. PT Coupling Company, Part # 25CSLII, Item # 1290325L2.

b. 2nd Hose End: Brass, 2-1/2” Cam & Groove Adapter by Hose Shank. PT Coupling Co., Part # 25E, Item # 1200525.

c. End Fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., PROGRIP™ C50SS

Stainless Steel Crimp Ferrules. Ferrules to be sized to match the hose and end fittings. No “or equal” bands, hose clamps, or sleeves will be accepted.

7. All end fittings must be made from virgin brass, meet Commercial Item Description (CID) A-A-59326 and shall have a working pressure of 250 PSI or greater. Any manufacturers hose end coupling offered other than the above referenced part numbers must be approved by PSNS & IMF Code 270TS.

8. Branding / Marking: Hose shall be continuously ink-branded, stencil painted, Mylar or stripe branded /marked with ½” minimum height lettering in a contrasting color to the Red band strip and Black Outer Cover of the hose.

The lettering shall state as a minimum:

a. Standard Hose Brand/Line/Model number, Working Pressure, Date of Manufacture

b. PSNS & IMF S/99

9. Price quotes for market survey request will not be accepted without the hose, fitting, and ferrule manufacturer cut sheets or product description sheets attached, which shall include as a minimum the technical characteristic of the components and the manufacturer’s address, telephone/fax number and manufacturer point of contact. The market survey price quote must reference the manufacturer’s part numbers for the item quoted.

10. All quoting vendors, if requested, must submit a five-foot long hose assembly at vendor expense, for destructive testing analysis.

11. All ”Or-Equal” offers must be approved by PSNS & IMF Temporary Services Engineering, Code 270TS prior to purchase.

Hose Test & Assembly Certification:

Each hose assembly shall be hydrostatically strength tested with commercial clean water as a test medium, at 275 (+10, -0) PSIG for 10 minutes. Each certified hose assembly is to be assigned by the manufacturer a unique serial number, to be permanently stamped or etch marked on the hose ferrule of each hose end. Hose manufacturer shall certify that hose assemblies are free of leaks, deformation, layer separation, excessive twisting or kinking; that end fittings are not damaged or faulty, and that the end fittings and ferrules are properly positioned on the hose ends, in accordance to NAHAD standards, also that the hose is does not have hairline cracks, breaks, abrasions, soft spots, bulges, or other defects in the outer cover. Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatically tested certification for each hose assembly shall be provided with shipped hoses. Written certifications shall include the witness signature of the tester, test date and must correspond to each unique hose serial number.

Applicable regulations: PSNS&IMFINST 10330.11F, PSNS&IMF 11300.10K, Industrial Process Instruction 0505-904C CH- 2, Codes of Federal Regulations Title 33, Volume 2, Section 154, and Commercial Item Description (CID) A-A-59326.

MATERIAL ITEM DESCRIPTION: FULLY ASSEMBLED DEIONIZED WATER HOSE

(1" I.D. x 25' Long)

Nomenclature:

1) Goodyear, “HI-PER” Hose, P/N 546-256

2) Saint-Gobain, “CHEMFLUOR TLCT” Hose, P/N 3832B-16TLCT-25FT

3) Unisource Manufacturing, “Series 2450” Hose, P/N 2450-100-025-C/E-BR

4) PureFlex, "FlexChem"

Or equal

“OR EQUAL” Purchase Specification:

Description:

1. Application: Deionized Water Transfer systems on piers, dry docks and within ship spaces.

2. Manufacturer Rated Working Pressure: 200 PSI minimum @ 70°F.

3. Burst Pressure: 1000 PSI minimum at 70°F.

4. Vacuum Hg @ 70°F: 29 Inches minimum.

5. Rated Continuous Temperature: -40ºF to 300ºF minimum.

6. No price quote or bid offer will be accepted without manufacturer hose, fitting, and ferrule cut sheets or product description sheet attachments. This shall include, as a minimum, the technical characteristics of the components and the manufacturer’s address, telephone/fax number and point of contact. The price quote must reference the manufacturer’s part numbers for the item quoted.

7. All quoting vendors, if requested, must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

8. PSNS & IMF Engineering Code 260.5 must approve all exceptions or “Or Equal” offer’s prior to purchase.

Construction:

9. Inner Tube: Flouroethylenepropylene (FEP).

10. Outer Cover: EPDM Rubber.

11. Color: Dark blue

12. Reinforcement: Synthetic textile fabric plies with double wire helix.

13. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories

Distribution (NAHAD) certification standards

14. Each hose assembly shall have the following components installed at each end:

1st Hose End: Female Cam & Groove Coupler x Hose Shank, Brass with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device, Gaskets shall be EPDM Rubber. PT Coupling Co., Part # 10CSLII, Item # 1290310L2.

2nd Hose End: Male Cam & Groove Adapter x Hose Shank, Brass. PT Coupling Co., Part # 10E, Item # 1200510.

End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., “Pro- Grip C50SS” Stainless Steel Crimp Ferrule, Part # xxxxxC50SS, Item # 541xxxxx.

Ferrule size shall match the hose and fittings.

Polypropylene Dust Cap, PT Coupling Co., Part # 10V, Item # 2701110, with EPDM Rubber Gasket.

Polypropylene Dust Plug, PT Coupling Co., Part # 20W, Item # 2701210.

15. All End Fittings must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

16. Branding/Marking: Hose shall be continuously ink-branded or Mylar striped in a contrasting color to the blue outer cover of the hose. The lettering shall state as a minimum:

Manufacturer Name, Hose Brand, Line, Model number, Hose Size (1") Manufacturers rated Working Pressure (200 PSI minimum)

“DI WATER SERVICE ONLY”

Hose Test & Assembly Certification:

17. After each hose assembly is completed, it shall be hydrostatically strength tested at 225 (+20,-0) PSI for 10 minutes, using commercial clean water as a test medium. Manufacturer shall certify that hose assemblies are: free of leaks, contain less than 90o of rotational twist over a 50 foot length, show no evidence of bending (kinking) to less than the minimum bend radius, contain no hairline cracks, breaks, abrasions, soft spots, bulges or other defects in the outer cover, end fittings are not damaged or faulty, and end fittings and ferrules are properly positioned on the hose ends.

Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatic testing (100% of hoses) shall be provided with shipped hoses.

(1" I.D. x 50' Long)

Nomenclature:

1) Goodyear, “HI-PER” Hose, P/N 546-256

2) Saint-Gobain, “CHEMFLUOR TLCT” Hose, P/N 3832B-16TLCT-50FT

3) Unisource Manufacturing, “Series 2450” HOSE, P/N 2450-100-050-C/E-BR

4) PureFlex, "FlexChem"

Or equal

“OR EQUAL” Purchase Specification:

Description:

1. Application: Deionized Water Transfer systems on piers, dry docks and within ship spaces.

2. Manufacturer Rated Working Pressure: 200 PSI minimum @ 70°F.

3. Burst Pressure: 1000 PSI minimum at 70°F.

4. Vacuum Hg @ 70°F: 29 Inches minimum.

5. Rated Continuous Temperature: -40ºF to 300ºF minimum.

6. No price quote or bid offer will be accepted without manufacturer hose, fitting, and ferrule cut sheets or product description sheet attachments. This shall include, as a minimum, the technical characteristics of the components and the manufacturer’s address, telephone/fax number and point of contact. The price quote must reference the manufacturer’s part numbers for the item quoted.

7. All quoting vendors, if requested, must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

8. PSNS & IMF Engineering Code 260.5 must approve all exceptions or “Or Equal” offer’s prior to purchase.

Construction:

9. Inner Tube: Flouroethylenepropylene (FEP).

10. Outer Cover: EPDM Rubber.

11. Color: Dark blue

12. Reinforcement: Synthetic textile fabric plies with double wire helix.

13. Hose end assembly shall be accomplished in accordance with established National Association for Hose & Accessories

Distribution (NAHAD) certification standards

14. Each hose assembly shall have the following components installed at each end:

1st Hose End: Female Cam & Groove Coupler x Hose Shank, Brass with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device, Gaskets shall be EPDM Rubber. PT Coupling Co., Part # 10CSLII, Item # 1290310L2.

2nd Hose End: Male Cam & Groove Adapter x Hose Shank, Brass. PT Coupling Co., Part # 10E, Item # 1200510.

End Fitting Interlocking Ferrules: End Fittings shall be coupled to the hose with PT Coupling Co., “Pro- Grip C50SS” Stainless Steel Crimp Ferrule, Part # xxxxxC50SS, Item # 541xxxxx.

Ferrule size shall match the hose and fittings.

Polypropylene Dust Cap, PT Coupling Co., Part # 10V, Item # 2701110, with EPDM Rubber Gasket.

Polypropylene Dust Plug, PT Coupling Co., Part # 20W, Item # 2701210.

15. All End Fittings must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

16. Branding/Marking: Hose shall be continuously ink-branded or Mylar striped in a contrasting color to the blue outer cover of the hose. The lettering shall state as a minimum:

Manufacturer Name, Hose Brand, Line, Model number, Hose Size (1") Manufacturers rated WP (200 PSI minimum)

“DI WATER SERVICE ONLY”

Hose Test & Assembly Certification:

17. After each hose assembly is completed, it shall be hydrostatically strength tested at 225 (+20,-0) PSI for 10 minutes, using commercial clean water as a test medium. Manufacturer shall certify that hose assemblies are: free of leaks, contain less than 90o of rotational twist over a 50 foot length, show no evidence of bending (kinking) to less than the minimum bend radius, contain no hairline cracks, breaks, abrasions, soft spots, bulges or other defects in the outer cover, end fittings are not damaged or faulty, and end fittings and ferrules are properly positioned on the hose ends.

Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatic testing (100% of hoses) shall be provided with shipped hoses.

(2" I.D. x 50' Long)

SUGGESTED SOURCES:

1) Goodyear, “HI-PER” Hose, P/N 546-256

2) Saint-Gobain, “CHEMFLUOR TLCT” Hose, P/N 3832B-32TLCT-50FT

3) Unisource Manufacturing, “Series 2450” Hose, P/N 2450-200-050-C/E-BR

4) PureFlex, FlexChem

Or equal

“OR EQUAL” Purchase Specification:

Description:

1. Application: Deionized Water Transfer systems on piers, dry docks and within ship spaces.

2. Manufacturer Rated Working Pressure: 200 PSI minimum @ 70°F.

3. Burst Pressure: 1000 PSI minimum at 70°F.

4. Vacuum Hg @ 70°F: 29 Inches minimum.

5. Rated Continuous Temperature: -40ºF to 300ºF minimum.

6. No price quote or bid offer will be accepted without manufacturer hose, fitting, and ferrule cut sheets or product description sheet attachments. This shall include, as a minimum, the technical characteristics of the components and the manufacturer’s address, telephone/fax number and point of contact. The price quote must reference the manufacturer’s part numbers for the item quoted.

7. All quoting vendors, if requested, must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

8. PSNS & IMF Engineering Code 260.5 must approve all exceptions or “Or Equal” offer’s prior to purchase.

Construction:

9. Inner Tube: Fluoroethylenepropylene (FEP)

10. Outer Cover: EPDM Rubber.

11. Color: Dark blue

12. Reinforcement: Synthetic textile fabric plies with double wire helix.

13. Hose end assembly shall be accomplished in accordance with established National Association for Hose &

Accessories Distribution (NAHAD) certification standards

14. Each hose assembly shall have the following components installed at each end:

• 1st Hose End: Female Cam & Groove Coupler x Hose Shank, Brass with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device, Gaskets shall be EPDM Rubber. PT Coupling Co., Part # 20CSLII, Item # 1290320L2.

• 2nd Hose End: Male Cam & Groove Adapter x Hose Shank, Brass. PT Coupling Co., Part # 20E, Item #1200520.

• End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip" C50SS Stainless Steel Crimp Ferrules. Ferrule size shall match the hose and fittings.

• Polypropylene Dust Cap, PT Coupling Co., Part # 20V, Item # 2701120,with EPDM Rubber Gasket.

• Polypropylene Dust Plug, PT Coupling Co., Part # 20W, Item # 2701220.

15. All End Fittings must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

16. Branding/Marking: Hose shall be continuously ink-branded or Mylar striped in a contrasting color to the blue outer cover of the hose.

The lettering shall state as a minimum:

A. Manufacturer Name, Hose Brand, Line, Model number, Hose Size (2") B. Manufacturers rated WP (200 PSI minimum)

C. " DI WATER SERVICE ONLY”

Hose Test & Assembly Certification:

17. After each hose assembly is completed, it shall be hydrostatically strength tested at 225 (+20,-0) PSI for 10 minutes, using commercial clean water as a test medium. Manufacturer shall certify that hose assemblies are:

free of leaks, contain less than 90o of rotational twist over a 50 foot length, show no evidence of bending (kinking) to less than the minimum bend radius, contain no hairline cracks, breaks, abrasions, soft spots, bulges or other defects in the outer cover, end fittings are not damaged or faulty, and end fittings and ferrules are properly positioned on the hose ends.

Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatic testing (100% of hoses) shall be provided with shipped hoses.

(2" I.D. x 50' Long)

Nomenclature:

1) Goodyear, “HI-PER” Hose, P/N 546-256

2) Saint-Gobain, “CHEMFLUOR TLCT” Hose, P/N 3832B-32TLCT-50FT

3) Unisource Manufacturing, “Series 2450” Hose, P/N 2450-200-050-C/E-BR

4) PureFlex, FlexChem

Or equal

“OR EQUAL” Purchase Specification:

Description:

1. Application: Deionized Water Transfer systems on piers, dry docks and within ship spaces.

2. Manufacturer Rated Working Pressure: 200 PSI minimum @ 70°F.

3. Burst Pressure: 1000 PSI minimum at 70°F.

4. Vacuum Hg @ 70°F: 29 Inches minimum.

5. Rated Continuous Temperature: -40ºF to 300ºF minimum.

6. No price quote or bid offer will be accepted without manufacturer hose, fitting, and ferrule cut sheets or product description sheet attachments. This shall include, as a minimum, the technical characteristics of the components and the manufacturer’s address, telephone/fax number and point of contact. The price quote must reference the manufacturer’s part numbers for the item quoted.

7. All quoting vendors, if requested, must submit a five-foot long hose assembly to Shop 99 at vendor’s expense, for destructive testing analysis prior to PSNS & IMF Engineering Code 260.41 approval to purchase.

8. PSNS & IMF Engineering Code 260.5 must approve all exceptions or “Or Equal” offer’s prior to purchase.

Construction:

9. Inner Tube: Fluoroethylenepropylene (FEP)

10. Outer Cover: EPDM Rubber.

11. Color: Dark blue

12. Reinforcement: Synthetic textile fabric plies with double wire helix.

13. Hose end assembly shall be accomplished in accordance with established National Association for Hose &

Accessories Distribution (NAHAD) certification standards

14. Each hose assembly shall have the following components installed at each end:

• 1st Hose End: Female Cam & Groove Coupler x Hose Shank, Brass with Stainless Steel Cam Arms, Pins, Pull Rings, and Passive Locking Device, Gaskets shall be EPDM Rubber. PT Coupling Co., Part # 20CSLII, Item # 1290320L2.

• 2nd Hose End: Male Cam & Groove Adapter x Hose Shank, Brass. PT Coupling Co., Part # 20E, Item #1200520.

• End fitting Interlocking Ferrules: End fittings shall be coupled to the hose with PT Coupling Co., “ProGrip" C50SS Stainless Steel Crimp Ferrules. Ferrule size shall match the hose and fittings.

• Polypropylene Dust Cap, PT Coupling Co., Part # 20V, Item # 2701120,with EPDM Rubber Gasket.

• Polypropylene Dust Plug, PT Coupling Co., Part # 20W, Item # 2701220.

15. All End Fittings must be made from virgin brass and meet Commercial Item Description (CID) A-A-59326.

16. Branding/Marking: Hose shall be continuously ink-branded or Mylar striped in a contrasting color to the blue outer cover of the hose.

The lettering shall state as a minimum:

A. Manufacturer Name, Hose Brand, Line, Model number, Hose Size (2") B. Manufacturers rated WP (200 PSI minimum)

C. " DI WATER SERVICE ONLY”

Hose Test & Assembly Certification:

17. After each hose assembly is completed, it shall be hydrostatically strength tested at 225 (+20,-0) PSI for 10 minutes, using commercial clean water as a test medium. Manufacturer shall certify that hose assemblies are:

free of leaks, contain less than 90o of rotational twist over a 50 foot length, show no evidence of bending (kinking) to less than the minimum bend radius, contain no hairline cracks, breaks, abrasions, soft spots, bulges or other defects in the outer cover, end fittings are not damaged or faulty, and end fittings and ferrules are properly positioned on the hose ends.

Written certification of satisfactory hose end assembly in accordance with NAHAD standards and satisfactory hydrostatic testing (100% of hoses) shall be provided with shipped hoses.