SPMYM2-21-Q-2486 (SALIENT CHARACTERISTICS) PREFABRICATED STORAGE BUILDING KIT ASSY.pdf

Salient Characteristics for a Assembly of a Pre-Fabricated Temporary Storage Building

Project #036-320 11 Sep 21

1 SCOPE - These salient characteristics reflects those characteristics that are essential to the minimum needs of the government for a complete turn-key “assembly” of a pre-fabricated temporary storage building (interior footprint: 15 ft wide x 30 ft long, with an 11”– 8” Eave, running the full length of the building). The building includes a 4:12 pitch gable with knee and ridge braces at 3 ft center to center, with 24 gauge exterior sheeting, Kynar finish, with hot-dip galvanized structural steel finish, and withstand a wind load of 70 MPH. The assembly site is on the Delta Pier, at Kitsap Naval Base, Kitsap. All building components shall be provided by the government in the form of kits (building, electrical, and anchoring). The pre-fabricated building, is a Kelly Klosure, Model Code #2015 IBC. Assembly shall include:

1.1 Installation of one standard steel personnel door (3 ft W x 7 ft H), that swings outward. It shall be located on one of the 30 ft walls, close to the back wall. Hardware provided is a standard light commercial lockset and closer

1.2 Installation on one standard sectional heavy duty roll-up steel door, 12 ft wide, 10 ft high, located on one of the 15 ft wide walls. The door shall use a manual operator chain lift to open/close the door

1.3 Assembly of a duckbill anchor system/kit. The contractor shall provide utilities locate services prior to installing the anchoring system/kit. At the site, there is approximately a 4 inch depth of asphalt, with approximately a 26 inch depth of fill (below the asphalt). The Duckbill anchoring system shall go no deeper then approximately 30 inches.

1.4 Assembly of an electrical kit to include:

1.4.1 Install conduit, wire, 100 amp breaker for new furnished panel (Square D, QO Series, 100 amp, single phase, 20 spaces, to be mounted on existing wall).

1.4.2 Mount eight (8) furnished LED fluorescent light fixtures from roof trusses, running the full length of the building.

Install the provided on/off switch located inside/next to the standard steel personnel door

1.4.3 Mount boxes, run conduit/wiring for 12 furnished standard 20 amp duplex outlets (spaced around the interior walls)

1.4.4 Install wiring kit for light fixtures, on/off switch and duplex outlets, with supplied clamping system, and pre-made 1/2” & 3/4” flexible steel conduit (that meet NEC codes)

1.5 Installation of six (6) building lifting pad eyes (military grade) with a provided steel baseplate for lifting the completely assembled building (with a spreader beam)

2 GOVERNMENT PROVIDED DESIGN - The government shall provide a pre-fabricated storage building design (produced by a qualified/professional engineer). The design includes exterior sheeting, factory attached to the face of the structure with anti-siphon overlapping edge to prevent leaks, and when attaching the exterior sheeting to the framework (on-site) self-tapping screws or other similar connection devices, shall not be required. Self-framing panels shall be provided that were fabricated by a manufacturer experienced in the business of engineering, producing, and field servicing structured pre-fabricated buildings. A complete set of assembly drawings tailored to this application shall be provided to illustrate assembly. The design drawings shall also include the details of an anchoring system, and a certified design for the six crane lifting pad eyes.

3 ADMITTANCE TO THE WORK SITE - Upon contract award, employees or representatives of the Contractor who require access to the Receiving Activity's facility at Naval Base Kitsap, Bangor (NBK, Bangor) shall be admitted to the work site only after they have been issued an appropriate Naval Region NW visitor security badge which is obtained at NBK, Bangor Pass & ID Office (located outside the NBK, Bangor Trident/ Main Gate).

Navy Region NW badge is required to gain access through the Operational Area Gate, or Waterfront Restricted Area, and is obtained through the on-line Base Authorization and Visit Request (BAVR) computer system. The prime contractor will need to submit all badge requests for their personal and for sub-contractor personnel. To request a Navy Region NW badge, Go on line to "https://www.bavr.cnic.navy.mil, and submit a request for a badge, a minimum of five (5) business days prior to arrival. All requested information highlighted in red is mandatory. Type N/A for “Driver’s License Information”. The "Command you are visiting" is: “Trident Refit Facility (TRF)” (or "NBK Bangor"). The “Company Name or Command” and “Work Phone” is your company/command information. The “Originating Command Security Officer Information” is Bruce Girkin, bruce.girkin@navy.mil. The "Sponsor E-Mail" for an on-line badge should be: aaron.k.peal@navy.mil (Aaron Peal, 360- 315-1047, 360-471-8624 (cell)). In the "Purpose of Visit" box, please explain in detail the purpose of your visit, and include the Contract Number, the Receiving Activity Point of Contact (name and telephone number) and ALL the buildings/areas/piers you are visiting. The “Start Date” is the day you expect to pick up your badge (you cannot pick it up early, even if approvals are completed). The “End Date” is the last date of your visit. Also send a copy of the contract (or contract modification if the delivery date has been changed) to Aaron Peal at the e-mail address listed above. You will be notified at the e-mail address you provided, when all approvals have been completed. If the BAVR computer system doesn't work, try different search engines (“Firefox” search engine seems to work the best). If BAVR still doesn’t work contact the Receiving Activity Point of Contact or our security manager, Aaron Peal, 360-315-1047, 360-471-8624 (cell) to schedule a visit(s), and shall provide the following information:

Salient Characteristics for a Assembly of a Pre-Fabricated Temporary Storage Building

Project #036-320 11 Sep 21

* Full Legal Name

* US Citizen Status

* All Company Contact Information

* Contract Number

Visitors must show proof of US Citizenship (at the NBK Bangor Pass & ID Office, located outside Bangor’s Main Gate (Trident Boulevard), by having an original active US Passport, an "Enhanced Driver's License", or an unlamented official birth certificate.