JUMPER_PGC01666_Mans BlueDress.docx

JUMPER, MAN'S, (BLUE, DRESS)

Jumper, Man’s, Blue dress shall be made in accordance With MIL-J-87035D, dated 4 August 1994.

PATTERN DATE: 28 MAY 1999.

A COPY OF STITCH ENLARGEMENT NUMBER 16-1-872 and NUMBER

16-1-16021 DATED 20 SEPT 1983, REFERENCED ON PAGE 3,

PARA. 2.1.2 AND PAGE 13, OPERATIONS 14 and 15 IS AVAILABLE

AT DPSC FOR THE MACHINE EMBROIDERED CROWTACKS AND

STARS ON THE JUMPER.

CAUTION NOTICE: WHEN BASIC MATERIAL IS CONTRACTOR

FURNISHED MATERIAL (CFM), THE BASIC MATERIAL

SHALL BE SPONGED USING THE "LONDONSHRINK"

COLD WATER METHOD PRIOR TO THE CUTTING

AND ASSEMBLY OPERATIONS.

A C.O.C. IS REQUIRED FOR THIS PROCESS

STANDARD SAMPLE FOR CLOTH, SERGE, WOOL, BLUE 3346

CONFORMING TO TYPE I, CLASS 5 OF MIL-DTL-823

IS AVAILABLE ON ROLL NO. 89096 FOR SHADE,

FINISH AND COLORFASTNESS.

ADDITIONAL INFORMATION FOR MIL-J-87035D:

Page 2, para. 2.1.1 Specifications, Standards, and Handbooks, Under “SPECIFICATIONS FEDERAL” Delete DDD-L-20 and Substitute “MIL-DTL-32075” and Delete “DDD-T-86” and Substitute “A-A-52071”. And Under “MILITARY” Delete “MIL-C-368 –Cloth, Satin, Rayon and Cloth, Twill Rayon” and under “STANDARDS FEDERAL” Delete FED-STD-751-Stitches, Seams, and Stitching”.

PAGE 3, Paragraph 2.2 Non-Government publications, Add new document as follows:

“AMERICAN SOCIETY FOR TESTING AND MATERIALS

ASTM-D-6193 Standard Practice for Stitches and Seams (Applications for copies should be obtained from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19426-2959)”

PAGE 4, para. 3.3.3 Tape. Line 2, Delete “Type II, Class 2, Of DDD-T-86” substitute “Type I, class 2, of A-A-52071” and Line 3, Delete “or type II, class 3 of DD-T-86” and substitute “class 3 of A-A-52071”.

PAGE 4, para. 3.3.4, Binding. Lines 4-5, Delete “As an alternate, a rayon binding can be used, which shall conform to class 1 of MIL-C-368.”

PAGE 5, para. 3.3.8.1, Combination Label., line 2, delete “DDD-L-20” and substitute

“MIL-DTL-32075”.

PAGE 5, para. 3.3.8.2 Size Label. Line 1, Delete “DDD-L-20” substitute “MIL-DTL-32075”

PAGE 6, para. 3.3.8.4 Label/tag, line 2 Delete “DDD-L-20” substitute “MIL-DTL-32075”

PAGE 6, PARA. 3.5.1, DELETE PATTERN PARTS LIST AND SUBSTITUTE:

. ABBREVIATED

SPEC NAME PIECE NO. CUT N0.

BASIC MATERIAL-CLOTH, SERGE, WOOL

FRONT FRONT 1 1/

FRONT YOKE FRONTYOKE 1 1/

BACK BACK 1 1/

BACK YOKE BACKYOKE 1 1/

SLEEVE SLEEVE 2

TOP COLLAR TOPCOLLAR 1 1/ 2/

UNDER COLLAR UNDERCOLLAR 1 1/ 2/

CUFFS CUFF 2 2/

INSIDE PATCH POCKET (30-34) INPTCHPKTA 1

INSIDE PATCH POCKET (36-52) INPTCHPKTB 1

INSIDE P.POCKET FLAP (30-34) INPKFLP-A 2

INSIDE P.POCKET FLAP (36-52) INPKFLP-B 2

POCKET WELT (30-36) PKTWELT-X 1

POCKET WELT (38-52) PKTWELT-Y 1

POCKET FACING (30-36) PKTFCNG-X 1

POCKET FACING (38-52) PKTFCNG-Y 1

POCKETING: CLOTH, TWILL

OUTSIDE BREAST POCKET OTRBRPKT 1

1/ CUT FACE SIDE UP

2/ FOR ALL LENGTHS

PAGE 6, Para. 3.3.8.4.

DELETE CURRENT "BARCODE LABEL/TAG"

REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG. EACH JUMPER SHALL BE INDIVIDUALLY

BAR-CODED WITH A PAPER TAG FOR PERSONAL

CLOTHING ITEMS. THE PAPER USED FOR THE TAGS

SHALL BE STANDARD BLEACHED SULFATE HAVING A

BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH

FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT

PRINTING. THE TAGS SHALL HAVE A HOLE AND

SHALL BE ATTACHED TO EACH ITEM BY A FASTENER,

CLEARLY LEGIBLE AND READABLE BY SCANNER.

THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE

A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT.

THE INITIAL "UPC" MUST APPEAR BENEATH THE

CODE. THE BAR CODES FOR NSN AND UPC SHALL BE

A MEDIUM TO HIGH DENSITY AND SHALL BE

LOCATED SO THAT THEY ARE COMPLETELY VISIBLE

ON THE JUMPER WHEN IT IS FOLDED AND PACKAGED

AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE

NO DAMAGE TO THE JUMPER.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION

THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON

WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/

TAGS:

BAR CODE OMITTED OR NOT

READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI)

OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM

CAUSES DAMAGE TO THE ITEM

PAGE 7, paragraph 3.6.1, Stitches, Seams, and Stitching. Line 2, Delete “FED-STD-751” substitute “ASTM D-6193”

ADDITIONAL INFORMATION FOR MIL-DTL-32075

MIL-DTL 32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIEMENTS OF THE

TYPE VI FINISHED LABEL". UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM".

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSN"s."

ADDITIONAL INFORMATION FOR A-A-52094A:

SIZE 16; TWIST Z; TYPE II; 16.0 OUNCES NOMINAL; GLAZED FINISH

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR A-A-50199

THREAD, POLYESTER, CORE COTTON, OR POLYESTER-COVERED

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE. CLASS 5 FABRIC IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

ADDITIONAL INFORMATION FOR NN-P-71:

NO ADDITIONAL INFORMATION

ADDITIONAL INFORMATION FOR DDD-T-86:

COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR

USE IN PREFERENCE TO DDD-T-86H

ADDITIONAL INFORMATION FOR MIL-DTL-823L:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-P-15011:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-B-17143:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-B-17757:

MIL-B-17757 IS CANCELLED WITHOUT REPLACEMENT.

ASTM-D-5118 IS AUTHORIZED FOR USE IN LIEU

OF MIL-B-17757.

(ref. T0857 - 6/15/06)

ADDITIONAL INFORMATION FOR MIL-C-21852:

INTERIM SPECIFICATION CHANGES TO MIL-C-21852F:

PAGE 1, CLASSIFICATION. PARA. 1.2, LINE 5 UNDER

"TYPE III", DELETE "2.0" AND SUBSTITUTE "1.8" AND

DELETE "68" AND SUBSTITUTE "61".

PAGE 4 PARAGRAPH 3.4, TABLE I. PHYSICAL REQUIREMENTS.

UNDER "TYPE III", "WEIGHT" REQUIREMENT, DELETE

"2.0 (68)" AND SUBSTITUTE "1.8 (61)".

PAGE 13, PARA.4.5.4 SPECTRAL REFLECTANCE TEST.

LINE 4, DELETE "HALON" AND SUBSTITUTE

"POLYTETRAFLUOROETHYLENE (PTFE)".

ADDITIONAL INFORMATION FOR FED-STD-751

FED-STD-751 HAS BEEN CANCELLED AND REPLACED

BY ASTM-D-6193, 4/98

STANDARD PRACTICES FOR STITCHES AND SEAMS.

THIS STANDARD SHOULD BE USED IN PREFERENCE

TO FED-STD-751.

(ref. T0216 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-STD-105E:

NOTE: MIL-STD-105 HAS BEEN CANCELLED AND REPLACED

BY THE FOLLOWING: "AMERICAN NATIONAL STANDARDS

INSTITUTE (ANSI) ANSI/ASQC Z1.4 - SAMPLING

PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES".

APPLICATION FOR COPIES SHOULD BE OBTAINED FROM:

AMERICAN SOCIETY FOR QUALITY CONTROL

611 EAST WISCONSIN AVE

MILWAUKEE, WI 53202

ADDITIONAL INFORMATION FOR MIL-STD-129P

MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE – DATED 19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DEFENSE SUPPLY CENTER (DSCP) CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DSCP C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIP- MENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT

HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR MIL-STD-2073-1:

NO ADDITIONAL INFORMATION FOLLOWS

ADDITIONAL INFORMATION FOR DD 81337 16-1-872:

16-1-872 CROWTACK FOR JUMPERS

. 7/31/90 (Ref. T6646)