SPI.pdf

MINIMUM SURFACE FINISH

ON MACHINED SURFACES

63 MICRO-INCHES, MILL

FINISHES ON ALL OTHERS.

GENERAL HOLE

TOLERANCES IN INCH:

.013 THRU .250: +.004/-.002

.251 THRU .750: +.005/-.002

.751 THRU 4.000: +.007/-.002

PARENTHETICAL INFORMATION IS FOR

REFERENCE ONLY.

UNLESS OTHERWISE SPECIFIED DIMENSIONS

ARE IN INCHES AFTER FINISHING.

DIMENSIONS IN [ ] ARE MILLIMETER.

TOLERANCES ON:

2 PLACE DECIMAL: ± .03 [0.76]

3 PLACE DECIMAL: ± .010 [0.254]

ANGULAR FORMED: ± 3

ANGULAR MACHINED: ± .5

COMMERCIAL TOLERANCES APPLY

TO STOCK SIZES

PART SHALL BE CLEAN AND FREE

OF BURRS AND SHARP EDGES

THIRD ANGLE PROJECTION

NOTES: UNLESS OTHERWISE SPECIFIED

1. THE DIMENSIONING AND TOLERANCING PRACTICE USED ON

THIS DRAWING IS IN ACCORDANCE WITH ASME Y14.5.

2. THIS DRAWING IS IN ACCORDANCE WITH ASME Y14.100.

3. SEE WIRE LIST 903-5004069-01WL.

4. MARK PART NUMBER AND REVISION LETTER ON LABEL (ITEM 100)

PER MIL-STD-130 USING SAE-AS478, METHOD 30 (INK), .09 INCH

HIGH CHARACTERS. LOCATE LABEL IN APPROXIMATE LOCATION

AS SHOWN.

5. SECURE WIRE WITH TYRAPS (ITEM 47) AS NEEDED.

6. WIRES NOT SHOWN IN ALL VIEWS FOR CLARITY.

7. LOCATE BAR CODE SERIAL NUMBER LABEL IN APPROXIMATE

LOCATION AS SHOWN.

8. AT2 & AT4 ARE SAT ITEMS. PL VALUES ARE NOMINAL ONLY.

ACTUAL VALUES MAY BE DIFFERENT DEPENDING UPON

INDIVIDUAL APPLICATION.

9. APPLY A PERMANENT THREAD LOCKING COMPOUND

(A2070-000023) TO THREADS BEFORE ASSEMBLY.

10. RUN & SECURE ALL WIRES & CABLES IN A WAY WHICH

PREVENTS THEM FROM EXTENDING BEYOND THE

BOUNDARIES INDICATED.

11. LOCATE CABLE MOUNTS (ITEMS 222, 224) APPROXIMATELY

AS SHOWN USING EPOXY ADHESIVE (ITEM 223) PER

MFG INSTRUCTIONS.

CAUTION

ELECTROSTATIC SENSITIVE

DEVICES ARE CONTAINED

IN THIS ASSEMBLY

SEE SEPARATE PARTS LIST12. TIGHTEN MATING CONNECTOR TO AN INITIAL INSTALLATION TORQUE OF 7-8 IN. LBS.

13. TIGHTEN CONNECTOR MOUNTING NUT TO AN INITIAL INSTALLATION TORQUE OF 26.0 2.5 IN. LBS.

14. REFERENCE DESIGNATORS ON COMPONENTS ARE SHOWN FOR WIRING PURPOSES ONLY

15. SEMI-RIGID CABLE (ITEM 31) SHOWN ON THIS DRAWING IS REPRESENTATIVE ONLY.

16. SECURE FERRITE BEADS OF W22 (ITEM 41) WITH TYRAPS (ITEM 51) TO CABLE MOUNT (ITEM 222).

17. 2-18 GHz RFGU PANELS WITH SERIAL NUMBERS 86831, 110696 AND 94961 (TEU SYSTEMS 1, 2 AND 3) WILL USE 900-5008582-01 FOR W22 (ITEM 41). ALL OTHERS WILL USE 900-5008582-02 FOR W22 (ITEM 41).

18. IF SMA CONNECTOR IS PRESENT ON A1 (ITEM 12), TERMINATE WITH 50 OHM

SMA TERMINATION (ITEM 19).

GOVERNMENT PURPOSE RIGHTS, NO EXPIRATION DATE

APPLICABLE CONTRACT. SUBCONTRACT S5030NAQP5 (ISSUED UNDER MTC TECHNOLOGIES, INC., CONTRACT F09603-01-D-0209/QP05)

COPYRIGHT 2008. THE GOVERNMENT'S RIGHTS TO USE, MODIFY, REPRODUCE, RELEASE, PERFORM, DISPLAY, OR DISCLOSE THESE TECHNICAL DATA ARE RESTRICTED BY DFARS 252.227-7013 PARAGRAPH (B)(2) OF THE RIGHTS IN TECHNICAL DATA-NONCOMMERCIAL ITEMS CLAUSE (DATED NOV 95). ANY REPRODUCTION OF TECHNICAL DATA OR PORTIONS THEREOF MARKED WITH THIS LEGEND MUST ALSO REPRODUCE THE MARKINGS.

DISTRIBUTION STATEMENT D. DISTRIBUTION AUTHORIZED TO THE DEPARTMENT OF DEFENSE AND THEIR CONTRACTORS FOR JOINT THREAT EMITTER (JTE) PROGRAM (ADMINISTRATIVE OR OPERATIONAL USE), (APRIL 2002).

OTHER REQUESTS FOR THIS DATA SHALL BE REFERRED TO 501 CBSS/GBLB, HILL AFB, UT.

WARNING. THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC 2751. ET. SEQ) OR THE EXPORT ADMINISTRATION ACT OF 1979, AS AMENDED, TITLE 50, U.S.C., APP. 2401 ET, SEQ. VIOLATIONS OF THESE EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL

PENALTIES, DISSEMINATED IN ACCORDANCE WITH PROVISIONS OF DOD DIRECTIVE 5230.25.

DESTRUCTION NOTICE. DESTROY BY ANY METHOD THAT WILL PREVENT DISCLOSURE OF CONTENTS OR

RECONSTRUCTION OF THE DOCUMENT.

CONTRACTOR NAME. AMHERST SYSTEMS, INC., A WHOLLY OWNED SUBSIDIARY OF NORTHROP GRUMMAN

CORPORATION, 1740 WEHRLE DRIVE, BUFFALO, NEW YORK 14221-7032

REVISIONS

ZONE REV. DESCRIPTION DATE APPROVED

A SEE ECN EC-004168 05/05/06 S.J.FLANNERY

B SEE ECN EC-007680 07/12/06 C.MANFREDI

C SEE ECN EC-008365 08/04/29 P.KOLNIAK

D SEE EC-009140 08/11/11 G. SMITH

E SEE EC-010460 09/08/17 P. SZALACH

F SEE EC-011100 10/05/05 M. GUNN

3 2

D D

F

A

B

C

D

5 48 7 6 3 DWG NO. SH 1

B

C

D

4 3

DRAFTING/ORIG

CHECK

PROGRAM MGT

DESIGNER

ENG MGT

CAGE CODE

D

SIZE DWG NO. REV

A

7 6 5

OF SHEETS

REV. STATUS

SHEET

REV.

8 1

903-5004069 1

NORTHROP GRUMMAN

CAD MAINTAINED. CHANGES SHALL

BE INCORPORATED BY THE DESIGN

ACTIVITY.

BUFFALO, NY 14221

DESIGN ENGR

MFG ENGR

ILS ENGR

PRODUCT ENGR

QA ENGR

PURCHASING

DESIGN ENGR

SIGNATURE SIGNATUREDATE DATE

-01

NO.

FIND

PARTS LIST

DESCRIPTION

NOMENCLATURE OR

QTYREQD INDENTIFYING NO.

MATERIAL

SPECIFICATION

03/09/08 1L4J7

SCALE 1:1 SHEET 1 OF 3R3745

903-5004069

ECA, RFGU, SYNTH,

2-18GHz DW

03/09/05

03/09/05 S.J. FLANNERY

-N/A

-N/A -N/A

-N/A

-N/A

N/A -

N/A -

D.G. SENTZ 03/09/05

N/A -

RELEASE NUMBER

(YY/MM/DD)

DATE

ORIGINAL CONTRACT NO

(YY/MM/DD) (YY/MM/DD)

C.M. WILSON

J.R. FENTON 03/09/05

APPLICATION

CONTRACT NO NEXT ASSEMBLY USED ON

PART OR

F

.12

6.0 .1

3.1 .1

(SERIAL NUMBER)

REV.

(PART NUMBER)

S/N:

184 224 47 11 184 70

11. 4 REQD

9.

6 REQD

7.

9. 2 REQD

7 REQD

7 REQD

7 REQD

4.

10.30

8 REQD

20 19 22 222 47 16.8.8.

AT3

G1

A1

A50

A T2

A T4

18.

2 PLCS

2 REQD

6 REQD

9.

4 REQD

11.

12.

13.

1.32

10.

-01 NON-CONFORMAL COATED

-51 CONFORMAL COATED

SHEET 2SCALE 1:1

SIZE

D 1L4J7

CAGE CODE DWG NO.

A

8 7

B

6 5

C

D

8 7 6 5

4 3 2 1

A

B

4 3 DWG NO.

C

SH 1

D

903-5004069

903-5004069 2

D

REV

*SEE WIRE LIST 903-5004069-01WL

RF CONNECTION DIAGRAM

DIGITAL CONNECTION DIAGRAM

ATTENUATOR, DC-18GHz

A9036-MF0015

AT4

ATTENUATOR, DC-18GHz

A9036-MF0006

AT2

MODULE, RF GEN

2-18 GHz A9082-021802

A1

SYNTH. 2.0-18.0 GHz, 1.0MHz A9019-021816

G1

FP

CCA, SERIAL_TM

903-6008080-XX

SYNTH. 2.0-18.0 GHz, 1.0MHz A9019-021816

G1

MODULE, RF GEN

2-18 GHz A9082-021802

A1

W23

W22

W21

W20 J15

J13

J5

J4J5 (PWR/LOGIC)

J3 (FM)

J4 (10 MHz)

J1 (PWR/LOGIC)

W1 W2

J2 (RF OUT)J2 J1

J2

J3

J4

J11

J12

A50

FP

J11 (TEST POINTS)

LINK

FPGA FAIL

J10 (HPA GRID) J16

P1P2

J1

DS1

DS2

P1

P2

W26

W27

MCWV-ACS TERM

SMA CNCTNR

A9030-000005

AT3

SHEET 3SCALE 1:1

SIZE

D 1L4J7

CAGE CODE DWG NO. REV

A

8 7

B

6 5

C

D

8 7 6 5

4 3 2 1

A

B

4 3 DWG NO.

C

SH 1

D

903-5004069

903-5004069 3

D

Sheet