SPI AK14351707.pdf

r-r .-1 \ti M

SI'

.-1

SPECIAL PACKAGING INSTRUCTION

Form Approved R/3JH

DT

0MB Na. 0704-0188 -

1. PART OR DRAWING NO. (CAGE) (NOMENCLATURE) 2. CODE INDENT 3. SPINO.

12530202 (118621 CYLINDER HEAD ASSEMBLY 19207 AK14351707

4. NATIONAL STOCK NO. 5. DATE OF DRAWING 6. REVISION

2815-01 -435-1707 07/29/98

7. CUP 8. ICC 19. UNIT PACK WT. (LS) 10. UNIT PACK CU (CU. FT.) 11. UNITPACKSIZE{IN.)

1 EA. NONE 88.0 2.819 31.1 X 17.6 X 8.9

12. PRESERVATION

�l.liill�ll�i!�ijlf JI Dll(lllli!ii�!

18. 19. 20.

STEPS RECD DESCRIPTION

a. LEVELA 1-B PRESERVATIVE: Mll·l·21260, GR. 10.

2-C 1 CONTAINER BASE: SEE NOTE C.

b. LEVELS 3-D 1 CUSHIONING: PPP-C-1797, TYPE I. SIZE: 24 X 12 X 1/4.

4-E 1 ENVELOPE: MIL-E-6060. SIZE: 16 X 36.

13. CLEANING S·F 1 WRAP: MIL-PRF-121. TYPE II GR. A. CL 2. SIZE: 29 X 28.

MIL·STD- 2073 METHOD 43

NOT APPLICABLE

MIL-STD-2073 6·G 1 CONTAINER: ASTM D 6880 IMODl, CL. 2, STYLE 4,

14. DRYING SIZE: 28·1/8 X 16-1/8 X 6·318. MIL-STD-2073

15. PACKING \!·''•' ,

••······ ""\f''"'Mf"''>'f"\!)'iij,tr Ath[ tmxit -1�r*%t-t/'I '.fa. ,. 1¾hJi�hitfv�ffn :::::,�t{�:::.AJ�j,f»Jt ,�

a. LEVELA

MIL-STD-2073-1 AND NOTE I

b. LEVELS

NOT APPLICABLE

16. MARKING

MIL-STD-129 AND NOTE H

17. NOTES/DRAWING

A. QUALITY ASSURANCE PROVISIONS:

1. INSPECT THE PRESERVATION AND UNIT PACK IN ACCORDANCE WITH MIL-STD-2073•1.

2. INSPECT PACKING IN ACCORDANCE WITH MIL-STD-1186 AND APPLICABLE CONTAINER SPECIFICATION.

B. FLUSH OR SLUSH INTERNALLY AND DRAIN EXCESS, THEN APPLY TO ALL EXTERIOR METALLIC SURFACES.

C. FABRICATE CONTAINER BASE "C" USING 3I4-INCH THICK A-A-55057 PLYWOOD, TYPE A, EXPOSURE 1, 48/24 SPAN RATING, GRADE CDX, SIZE 16 X 28-INCHES. FABRICATE BLOCKING AND SKIDS USING MIL-STD-731, GROUP II LUMBER AS SHOWN IN SKETCHES ON PAGES 2 AND 3. SECURE SKIDS TO BASE USING FF-N-105 NUMBER 6 NAILS. SECURE

BLOCKING TO BASE USING FF•N-105 NUMBER 12 NAILS.

D. CENTER PAD "D" ON BASE "C" USING BASE "C" AS A TEMPLATE, LOCATE AND FABRICATE FOUR HOLES.

E. ENVELOPE "E" SHALL BE FABRICATED IN ACCORDANCE WITH THE FOLLOWING. GASKETED HOLES SHAU BE IN ACCORDANCE WITH Mll·E-6060. CENTER ENVELOPE "E" ON BASE "C" USING BASE "C'' AS A TEMPLATE, LOCATE AND FABRICATE FOUR HOLES AS SHOWN IN SKETCH ON PAGE 3. SECURE CYLINDER HEAD ASSEMBLY TO BASE "C" WITH

FOUR CARRIAGE BOLTS 1/2 X 4-1/2-INCH AND APPROPRIATE NUTS AND LOCKWASHERS.

F. SECURE WRAP USING TAPE.

G. CONTAINER SHALL BE MODIFIED AS FOLLOWS: HOOD SHALL BE FABRICATED USING 1-INCH NOMINAL LUMBER, AND SHALL BE MADE TO FIT OVER CONTAINER BASE RESTING ON SKIDS. SECURE HOOD TO BASE USING FF-S-111 SCREWS

OF THE APPROPRIATE SIZE.

H. IN ADDITION TO MIL-STD-129 MARKINGS THE UNIT CONTAINER SHALL BE MARKED ON THE TOP AND ONE SIDE WITH 1/2 INCH HIGH (MIN.) BLACK LETTERS,"REUSABLE CONTAINER AND CUSHIONING, DO NOT DESTROY", IN ADDITION, THE TOP SHALL BE MARKED WITH 1/2 INCH HIGH (MIN.) LETTERS "REMOVE SCREWS TO OPEN CONTAINER", I. THE UNIT CONTAINER IS THE SHIPPING CONTAINER.

DD Form 2169, JUN 86 Previous editions are obsolete. Page 1 of 3 pages

A