SPI AG00000667.pdf

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

1.PART OR DRAWING NO.

7586626

2. CODE IDENT

80063

3. SPI NO.

AG00000667

4. NATIONAL STOCK NO

5985016918795

5. DATE OF DRAWING

23004

6. REVISION

7. QUP

8. ICQ

NONE

9.UNIT PACK WEIGHT 10.UNIT PACK CUBE

201.65 ft3

11.UNIT PACK SIZE

115”x101”x30”

12. PRESERVATION 18.

STEPS

19.

REQD

20.

DESCRIPTION

MILITARY

NOTE 1

N/A N/A N/A

13. CLEANING

MIL-STD-2073-1

APPLICABLE DOCUMENTS

14. DRYING

MIL-STD-2073-1

MIL-STD-2073-1

MIL-STD-129

MIL-PRF-26514

ASTM D6251

A-A-59136

15. PACKING

a. LEVEL A

MIL-STD-2073-1

b. LEVEL B N/A

16. MARKING

MIL-STD-129

NOTES/DRAWINGS

1. PRESERVATION. In accordance with (IAW) MIL-STD-2073-1 as specified herein, ensuring compliance with the applicable requirements of that standard.

1.1 STT-208 Reflector. - Unit Pack. Preserve each antenna IAW MIL- STD-2073- 1, Method 10 with a crate IAW ASTM D6251 Type III, Class 2 with specifications as described below.

1.1.1 Container Characteristics.

1.1.1.1 Construct wooden crate IAW ASTM D6251 with length: 115in., width:

101in., height: 30in.

1.1.1.2 Cushioning.

1.1.1.2.1 Four pieces of cushioning conforming to MIL-PRF-26514 (Polyurethane) Class 1, Grade A, Type I, will be glued to each side of the crate where the edges of the reflector are closest to the crate (See Figure 1.1). This cushioning should be 24 inches wide by 24 inches long and one inch thick.

REFLECTOR,ANTENNA

1.1.1.2.2 Two inches of cushioning of polyethylene, conforming to A-A-59136, will be glued to the base of the crate (115in x101in), which the antenna is placed on top of.

1.1.1.2.3 Three wooden braces, made of 2x4’s (nominal dimension) approximately 100” long (finished interior width may vary slightly) spanning the width of the crate. These braces should fit snugly against 2” cushioning conforming to A-A-59136, which is sandwiched between the back of the reflector and the brace (See figure 1.2).

This cushioning should be 24” wide by 115” long. These braces will be secured to the shell of the crate using screws.

1.1.1.2.4 Additional 2” cushioning with length of 12” and width of 24” conforming to MIL-PRF-26514 (Polyurethane) Class 1, Grade A, Type 1 should be placed at the angled base of the reflector to prevent shifting (see Figure 1.3)

2. Packing

2.1 LEVEL A. Unit pack will serve as shipping container.

3. Marking: All unit packs, intermediate packs, and exterior shipping containers shall be legibly and durably marked in accordance with MIL-STD- 129.

3.1 Place “Arrow up, Fragile, and Do not double stack” markings/stickers on the crate, Do Not place any labels on the reflector.

4. REQUIREMENTS FOR WOOD PACKAGING MATERIAL. All CONUS and OCONUS shipments utilizing wood packaging material, such as pallets, dunnage, crating, packing blocks, drums, cases, load boards, pallet collars, and skids, shall meet the International Standards for Phytosanitary Measures, ISPM 15, entitled “Regulation of Wood Packaging Material in International Trade”.

DA FORM 2169, JUN 86 Page 2 of 3

DA FORM 2169C, JUN 86 Page 3 of 3

SPECIAL PACKAGING INSTRUCTION

(Continuation Sheet )

Form Approved OMB No. 0704-0188

1. PART OR DRAWING NO.

7586626

2. CODE IDENT

80063

3. SPI NO.

4. NATIONAL STOCK NO

5985016918795

5. DATE

16164

6. REVISION

Figure 1 Crate Layout and Cushioning

Edge Cushioning

Bracing