Specs with Tech Requirements- VA Medical Center Inpatient.docx

Specifications with Technical Requirements Pharmacy Modular Casework Pharmacy Renovation Project G.V. (Sonny) Montgomery VAMC Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Pharmacist Workstations Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions) Salient Characteristics:

Modular Casework Size (6) workstations: 30”A.F.F., 4’-5’6” wide for knee space, data/ power openings available below the workstation in the casework wall with ledge. Unit is designed to have working countertop with ledge above to hold prescriptions to be verified. Unit to have printer pull out drawers and a 30” high storage unit for Pharmaceutical reference books. These units are free standing desk units designed with the following components: solid surface countertop, knee space with back panel and modular hospital grade duplex receptacles and data boxes integrated for each workstations. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Each work station is separated by a high pressure laminate panel to provide privacy. Overall dimensions: SEE DRAWINGS.

GENERAL REQUIREMENTS FOR MODULAR MILLWORK

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Countertop- Solid surface (Wilsonart San Grabriel Riverstone 9138RS).

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Pharmacy Renovation Project G.V. (Sonny) Montgomery VAMC Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Non-sterile Compounding and Compounding Supply Storage Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions)

Unit is designed with the following components: free standing stainless steel portable sink cabinet with doors below, overhead adjustable shelving with adjustability to be sloping and flat, (2) 18” gravity fed drawers with dividers for storage of bottles and caps for mixing liquids in pharmacy. Includes, sink bowl, wrist blade faucet and drain. Solid Surface counter top. These free standing units have a back panel with modular hospital grade duplex receptacle integrated for equipment needed in this area. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Supply storage is 18” and 24” deep adjustable shelving. Overall dimensions: SEE DRAWINGS.

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Work top surface uses Solid Surface material.

· Adjustable 4-way hinges.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick *Shelving Units shall have 7 adjustable shelves.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves adjustable vertically on 1" centers.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Pharmacy Renovation Project RX Fill and Check Area

Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Pharmacy Work Stations and Storage Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions)

Modular Casework Size (4) workstations: 30”A.F.F., 48” wide for knee space, data/ power openings available below the workstation in the casework wall with an adjacent work table. Adjustable shelves above with sloping shelves and task lighting. Unit is designed to have working countertop with cabinetry above providing storage and space to hold equipment and supplies. These units are free standing desk units designed with the following components: overhead adjustable shelving, solid surface countertop, knee space with back panel and modular hospital grade duplex receptacles and data boxes integrated for each workstations. Supply storage is 18” deep adjustable shelving. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Overall dimensions: SEE DRAWINGS.

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

*Steel supports/back panels: shall be capable to support up to 600 pounds. Finish shall be powder coated paint that shall be coordinated with laminate finish. They should include slant brackets at 2” intervals, a retainer clip and shall allow for the adjustment of shelves on steel pins. Back panels shall be removable and able to incorporate electrical duplex boxes.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves noted as being sloping shall also adjust to a flat position. Adjustable vertically on 1" centers and from horizontal to 15, 30, and 45-degree slope down.

*All shelves shall be completely reversible with retainer lips being turned up, down, or to the back as required for use.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Pharmacy Renovation Project Automation Support Area

Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Unit Dose Filling and Pharmacist Verification Workstations Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions) Salient Characteristics:

Pharmacy storage, Filling and Verification workstations to function as the pharmacy check and fill operations. Unit is designed to have a working countertop with cabinetry below and above providing storage and space to hold equipment and supplies. Unit is a free standing, two-sided island with pass thru opening to receive orders from the other side with upper shelves, 50" deep countertop and countertop with storage below for printer equipment. (4) 41" wide shelf storage units below counter at work island batch fill and verification. Unit is designed with the following components: Secured suspended upper-case support system with adjustable shelving, 24" wide task lighting, solid surface countertop, open under counter storage, pull out printer shelf, knee space with back panel and modular hospital grade duplex receptacles and data boxes integrated. Power entry from overhead, junction box provided by casework vendor. Electrical and data to be run by and terminated by casework vendor. Overall dimensions SEE DRAWINGS.

Side 1 (Unit Dose Fill): (2) 48" wide under counter shelves, set up for 2 workstations, (1) 42” wide open area for to house trash and shredders, (4) 34” wide sloping overhead storage with task lighting and pass thru (maintain 20" clear between bottom of task light and top of worksurface) Side 2 (Pharmacy Check): (2) 68" desk area with knee space, (4) 34” wide shelf sloping overhead storage with task lighting and pass thru (maintain 20" clear between bottom of task light and top of worksurface), set up for 2 workstations with printer drawers below counter.

Solid Surface CTR top.

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

*Shelving Units shall have 7 adjustable shelves.

*Steel supports/back panels: shall be capable to support up to 600 pounds. Finish shall be powder coated paint that shall be coordinated with laminate finish. They should include slant brackets at 2” intervals, a retainer clip and shall allow for the adjustment of shelves on steel pins. Back panels shall be removable and able to incorporate electrical duplex boxes.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves noted as being sloping shall also adjust to a flat position. Adjustable vertically on 1" centers and from horizontal to 15, 30, and 45-degree slope down.

*All shelves shall be completely reversible with retainer lips being turned up, down, or to the back as required for use.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Unit Dose Packaging Workstation Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions)

Pharmacy Unit Dose Packaging workstation to function as the support area for equipment and packaging supplies to convert bulk medicines into unit dose form. Modular casework is designed to have a working countertop with cabinetry below and above providing storage and space to hold equipment and supplies. Adjustable shelves above with sloping shelves Unit is a free standing,39” high, 8’ wide countertop with storage below and drawer for printer equipment. These units are free standing units designed with the following components: solid surface countertop, storage below and printer drawer with back panel and modular hospital grade duplex receptacles and data boxes integrated. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Overall dimensions: SEE DRAWINGS.

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

*Shelving Units shall have 7 adjustable shelves.

*Steel supports/back panels: shall be capable to support up to 600 pounds. Finish shall be powder coated paint that shall be coordinated with laminate finish. They should include slant brackets at 2” intervals, a retainer clip and shall allow for the adjustment of shelves on steel pins. Back panels shall be removable and able to incorporate electrical duplex boxes.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves noted as being sloping shall also adjust to a flat position. Adjustable vertically on 1" centers and from horizontal to 15, 30, and 45-degree slope down.

*All shelves shall be completely reversible with retainer lips being turned up, down, or to the back as required for use.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Narc Filling Workstations and Storage Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions)

Pharmacy narcotic vault workstations and storage function as the area to store, prepare and dispense schedule 2-5 drugs. Unit is designed to have a 39"H working countertop with cabinetry below and above providing storage and space to hold equipment and bulk supplies. Unit is designed with the following components: 2 work areas with knee space, overhead adjustable shelving with adjustability to be sloping and flat, (3) 24” wide printer pull out drawers, storage under counter. Solid Surface counter top. These free standing units have a back panel with modular hospital grade duplex receptacle integrated for equipment needed in this area. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Narcotic storage is 18” deep adjustable shelving. Use drawing package for final dimensions and layouts. Overall dimensions: SEE DRAWINGS

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

*Shelving Units shall have 7 adjustable shelves.

*Steel supports/back panels: shall be capable to support up to 600 pounds. Finish shall be powder coated paint that shall be coordinated with laminate finish. They should include slant brackets at 2” intervals, a retainer clip and shall allow for the adjustment of shelves on steel pins. Back panels shall be removable and able to incorporate electrical duplex boxes.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves noted as being sloping shall also adjust to a flat position. Adjustable vertically on 1" centers and from horizontal to 15, 30, and 45-degree slope down.

*All shelves shall be completely reversible with retainer lips being turned up, down, or to the back as required for use.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

Jackson, Mississippi Project: Pharmacy Renovation Project Issue Date: Feb 2022 Total Quantity: 1

☒ Finish Sample Required if Checked ☒ Manufacturer Certified Installation Required if Checked

Item Name: Outpatient Filling Workstation and Storage Brand Name or Equal: Modular Pharmacy Solutions Width: Assorted Depth: Assorted Height: Assorted (Use drawing package to identify dimensions)

Pharmacy Outpatient Filling workstation to function as the filling area for nights, weekends and for discharged patients. Modular casework is designed to have a working countertop with cabinetry below and above providing storage and space to hold equipment and supplies. Adjustable shelves above with sloping shelves. Unit is a free standing,39” high, 5’9” wide countertop with storage below and drawer for printer equipment. These units are free standing units designed with the following components: solid surface countertop, knee space below and printer drawer with back panel and modular hospital grade duplex receptacles and data boxes integrated. Power entry from overhead junction box provided by casework vendor. Electrical and data to be run by terminated by casework vendor. Supply storage is 18” deep adjustable shelvin. Overall dimensions: SEE DRAWINGS.

· All surfaces must be cleanable with hospital grade germicides and bleach solutions without harm to finishes.

· Cabinets constructed of HPL over a ½” minimal thickness low VOC substrate with all edges sealed with matching edge- band.

· Cabinet interiors fully HPL or LPL lined with no exposed substrate.

· Warranty- Limited Lifetime

· To include minimum of the following specifications:

· A component-based line of cabinetry and coordinating work tops to be used in labs and pharmacy spaces to supply a “built- in” look while maintaining the quality and flexibility of a modular approach. A wide variety of fully modular cabinet components available for upper and lower storage.

· Drawer construction options of standard box type with replaceable drawer front and unitary interior box for use in healthcare.

· Full extension steel ball bearing drawer glides.

· Work top surface uses Solid Surface material.

· Adjustable height shelving, HPL surface on all sides of shelves and shelving unit

ADDITIONAL REQUIREMENTS ARE AS FOLLOWS:

Materials:

*Core material shall be particle board conforming to CS 236-66 45 pound, “B” density, Class 1 of Type 1 *Laminated plastic for general construction shall be 1/32” or 1/16” thick high-pressure type *All top, side and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finish as selected for exposed surfaces.

*Adhesive for laminate shall be urea-formaldehyde resin free.

*Edge moldings shall be PVC edge band and appear on all edges of the casework that are visibly exposed. Molding shall be the same thickness as shelf when on shelf, counter molding shall be 1-1/4” wide and flush with worksurface.

*Shelving shall be 3/4" thick core with laminate on both sides.

*Casework shall be fabricated using flush construction methods with modern machinery.

*Casework shall be delivered fully constructed and ready for installation. Each unit shall be self-supporting and permit relocation. The sharing of component parts to form a rigid, modular, free-standing assembly shall not be acceptable Features:

*Unit shall be free standing with ability to anchor to floor or walls.

*Unit shall have a non-adjustable bottom shelf that is the base of the cabinet positioned on top of the toe kick *Unit shall have a 4" toe kick.

*Shelving Units shall have 7 adjustable shelves.

*Steel supports/back panels: shall be capable to support up to 600 pounds. Finish shall be powder coated paint that shall be coordinated with laminate finish. They should include slant brackets at 2” intervals, a retainer clip and shall allow for the adjustment of shelves on steel pins. Back panels shall be removable and able to incorporate electrical duplex boxes.

Drawers:

*Drawer module inserts shall be individual modular units that are completely removable and relocatable without being disassembled.

*Drawer suspension shall have full extension travel, full steel ball bearings of carbonized steel and a positive stop and lock-in closed position (self-closing drawer slides).

*Doors and drawer fronts shall be a minimum of 13/16" thick with composed out of the same material as the cabinetry finished with high pressure laminate.

Worksurfaces:

*Countertop shall run the length of the end panels and be composed out of a solid surface material. Core shall be 1- 1/8" thick with 1/16" laminate finish.

*Backsplash and returns shall be provided where shown on drawings.

*All exposed edges shall be radiused ¼”.

Shelves:

*All shelves shall be 3/4” thick core with high pressure laminate on both sides.

*All shelves noted as being sloping shall also adjust to a flat position. Adjustable vertically on 1" centers and from horizontal to 15, 30, and 45-degree slope down.

*All shelves shall be completely reversible with retainer lips being turned up, down, or to the back as required for use.

*All top, side, and bottom panels and shelf panels shall be laminated with high pressure laminate including cabinet interiors in the same color and finishes as selected for the exposed surfaces. All cabinet backs will have HPL on interior surface.

Electrical:

*Units are prewired with electrical from the factory and support the data as required.

All modular casework should be field verified prior to purchase/installation. Building contractor to pull wiring. Either construction or activation contractor to have licensed electrician make the connections from building to modular casework.

*Electrical fixtures shall be Hospital Grade 20 amps, 120 volt, 3-wire polarized grounded duplex receptacles.

*Grommet holes to be drilled on site after installation of equipment for proper coordination.

Quality Assurance:

*Manufacturer must have a minimum of 5 years experience in providing manufactured casework for similar types of projects. Manufacturer facility must be certified to premium grade by the AWI Quality Certification Program.

*All pharmacy casework included in this specification shall be made by a pharmacy casework manufacturer who is a specialist in the design and manufacture of pharmacy casework and has in operation, a factory adequate in size, with facilities for and devoted to the manufacture of the equipment he or his distributor proposes to supply. This requirement is stated for the Owners protection to eliminate any divided responsibility and to ensure that all completed assemblies shall be in harmony and uniform in design, color, type of hardware, etc., for the completed facility/installation.

*A minimum of five years experience in the design, sale, manufacture, shipping, and installation of the quality and type of pharmacy casework specified herein shall be required Finishes:

*Casing, shelves, end panels- Laminate (Wilsonart Pepperdust D327-60), with PVC edge banding to match laminate. Final finishes to be approved by X.

image3.png image4.png image5.png image6.png image7.png image1.png image2.png