Container LTC Presolicitation Descriptions.pdf

Product Descriptions for 38 ISO container NSNs are listed below. The following specifications, referenced in this document, will be available if these items are solicited:

• MIL-PRF 32410 (Applies to # 3)

• MIL-PRF 32349A (Applies to # 12, 15, 17, and 18)

• ATPD-2338C (Applies to # 5 and 6)

• ATPD-2339A (Applies to # 20, 22, 23, 25, 27, 30, 32, and 33)

1) NSN 8150-01-481-3740, BICON Double doors on one side Green.

8150-01-481-3740

BICON,FREIGHT,GENERAL

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER

LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS,

THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A

SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE

THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES

CONTAINER SHALL BE NEW OR ONE-TIME USED*. CONTAINER SHALL NOT EXCEED ONE

YEAR FROM THE DATE OF MANUFACTURE.

DIMENSIONS: 10' L X 8' W X 8'6" H

DLA TROOP SUPPORT HAS REVIEWED THIS ITEM AND HAS DETERMINED THE DOD BAR

CODE MARKINGS CITED IN THE PREPARATION FOR DELIVERY SEGMENT OF THIS

SOLICITATION ARE NOT REQUIRED. THIS DETERMINIATION ONLY RELIEVES THE BAR

CODING IN ACCORDANCE WITH AIM BC1 AND DOES NOT RELIEVE ANY OTHER MARKING

REQUIREMENTS THAT ARE NOT BAR CODED IN THIS SOLICITATION.

CORRUGATED STEEL SIDES, ROOF, AND SWING DOORS ON ONE END.1-1/8" THICK

PLYWOOD FLOORS.

FORKLIFT TESTED TO 16,000 LBS PER 44 SQUARE INCHES (14 GAUGE) CORRUGATED

STEEL SIDES, ROOF AND DOORS. (7 GAUGE) STEEL END FRAMES, FORKLIFT POCKETS.

VENTS (2), LASHING BARS PER POST (2), 6 TOP & BOTTOM SIDE WALL LASHING RINGS (24

TOTAL), 8 RECESSED FLOOR ANCHOR POINTS, 5 FRONT CORNER POST TIE DOWNS (10

TOTAL). DECKING AND SHORING BEAMS (16), CONNECTING COUPLERS (2),

CONNECTING COUPLER STORAGE BRACKET (1), ADJUSTABLE SHELVING BRACKETS (4

SETS). BOTTOM RAIL PROTECTION. MANIFEST BOX (2)

ANTI-PILFERAGE PROVISIONS

MAXIMUM TARE WEIGHT 3,000 LBS, MAXIMUM GROSS WEIGHT 26,455 LBS.

MANUFACTURED TO THE LASTEST REVISION OF ISO 668, ISO 1161, ISO 1496-1, ISO 6346

& ISO 830.

MUST BE CERTIFIABLE TO INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC)

AND INTERNATIONAL MARITIME DANGEROUS GOODS (IMDG) STANDARDS. CONTAINER

SHALL BE INSPECTED TO VERIFY COMPLIANCE WITH MIL-STD-209, MIL-STD-810, MIL-

STD-1366 AND MIL-STD-1472.

COLOR GREEN # 34094 UNLESS SPECIFIED BY THE CUSTOMER. NON-CARC PAINT

COPIES OF ISO STANDARDS ARE AVAILABLE FROM THE AMERICAN NATIONAL

STANDARDS INSTITUTE (ANSI). USE URL WWW.ANSI.ORG COPY OF INTERNATIONAL

CONVENTION FOR SAFE CONTAINERS (CSC) IS AVAILABLE FROM URL WWW.IMO.ORG

IAW REFERENCE STD NR MIL-STD-209K

REVISION NR K DTD 02/22/2005

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-810H

REVISION NR H DTD 01/31/2019

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1366E

REVISION NR E DTD 10/31/2006

http://www.ansi.org/ http://www.imo.org/

IAW REFERENCE STD NR MIL-STD-1472H

REVISION NR H DTD 09/15/2020

2) NSN 8150-01-481-3741, BICON Double doors on one side Tan.

8150-01-481-3741

BICON,FREIGHT,GENERAL

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER

LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS,

THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A

SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE

THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RD003: COVERED DEFENSE INFORMATION POTENTIALLY APPLIES

CONTAINER SHALL BE NEW OR ONE-TIME USED*. CONTAINER SHALL NOT EXCEED ONE

YEAR FROM THE DATE OF MANUFACTURE.

DIMENSIONS: 10' L X 8' W X 8'6" H

DLA TROOP SUPPORT HAS REVIEWED THIS ITEM AND HAS DETERMINED THE DOD BAR

CODE MARKINGS CITED IN THE PREPARATION FOR DELIVERY SEGMENT OF THIS

SOLICITATION ARE NOT REQUIRED. THIS DETERMINIATION ONLY RELIEVES THE BAR

CODING IN ACCORDANCE WITH AIM BC1 AND DOES NOT RELIEVE ANY OTHER MARKING

REQUIREMENTS THAT ARE NOT BAR CODED IN THIS SOLICITATION.

CORRUGATED STEEL SIDES, ROOF, AND SWING DOORS ON ONE END. 1-1/8" THICK

PLYWOOD FLOORS. FORKLIFT TESTED TO 16,000 LBS PER 44 SQUARE INCHES (14

GAUGE) CORRUGATED STEEL SIDES, ROOF AND DOORS. (7 GAUGE) STEEL END FRAMES,

FORKLIFT POCKETS. VENTS (2), LASHING BARS PER POST (2), 6 TOP & BOTTOM SIDE WALL

LASHING RINGS (24 TOTAL), 8 RECESSED FLOOR ANCHOR POINTS, 5 FRONT CORNER

POST TIE DOWNS (10 TOTAL). DECKING AND SHORING BEAMS (16), CONNECTING

COUPLERS (2), CONNECTING COUPLER STORAGE BRACKET (1), ADJUSTABLE SHELVING

BRACKETS (4 SETS) BOTTOM RAIL PROTECTION. MANIFEST BOX (2)

ANTI-PILFERAGE PROVISIONS

MAXIMUM TARE WEIGHT 3,000 LBS, MAXIMUM GROSS WEIGHT 26,455 LBS.

MANUFACTURED TO THE LASTEST REVISION OF ISO 668, ISO 1161, ISO 1496-1, ISO 6346

& ISO 830.

MUST BE CERTIFIABLE TO INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC)

AND INTERNATIONAL MARITIME DANGEROUS GOODS (IMDG) STANDARDS. CONTAINER

SHALL BE INSPECTED TO VERIFY COMPLIANCE WITH MIL-STD-209, MIL-STD-810, MIL-

STD-1366 AND MIL-STD-1472.

COLOR TAN # 33446 UNLESS SPECIFIED BY THE CUSTOMER. NON-CARC PAINT

COPIES OF ISO STANDARDS ARE AVAILABLE FROM THE AMERICAN NATIONAL

STANDARDS INSTITUTE (ANSI). USE URL WWW.ANSI.ORG COPY OF INTERNATIONAL

CONVENTION FOR SAFE CONTAINERS (CSC) IS AVAILABLE FROM URL WWW.IMO.ORG

IAW REFERENCE STD NR MIL-STD-209K

REVISION NR K DTD 02/22/2005

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-810H

REVISION NR H DTD 01/31/2019

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1366E

REVISION NR E DTD 10/31/2006

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1472H

3) NSN 8150-01-609-6554, BICON

BICON II CARC TAN CONTAINERS

NSN: 8150-01-609-6554

Mfr CAGE: 81337

Mfr Part Number: 5-13-9843-6

Description/Specs./Work Statement

PROCUREMENT DOCUMENTATION TITLE:

MIL-PRF 32410

PACKAGING/PACKING/SPECIFICATIONS:

SEE PACKAGING REQUIREMENT NARRATIVE FOR DETAILS

UNIT PACK: 001

LEVEL PRESERVATION: Military

LEVEL PACKING: A

This product description (NSN 8150-01-609-6554) incorporates the following clauses C11, C13, and D5.

C.11 Drawing Limitations

(a) The drawings supplied with this contract are not shop or process drawings. They are engineering design drawings. They are adequate to permit manufacture, and:

(1) depict the completed (item(s), and

(2) serve as the basis for inspection of the completed item(s).

(b) These drawings DON'T cover intermediate drawings/specifications or steps in the manufacturing process. As a result, even if you meet all the dimensions and tolerances specified in the engineering design drawing for each individual part, a cumulative unacceptable fit for the contract item could result.

( c ) The Contractor is responsible for producing the shop or process drawings needed to cover intermediate steps in the manufacturing process.

( d ) The Contractor is responsible for obtaining all specifications and drawings necessary to manufacture the items being solicited in accordance with the TDP including all incorporated specifications and drawings. Delivery delays are not excusable where the Contractor asserts that it did not have a specification or drawing and has failed to request, in writing, the specification from either the Procuring Contracting Officer or Contract Specialist prior to the solicitation closing date.

(e) If you fail to produce an end item with a cumulative fit that conforms to Government drawings, specifications or other supplemental manufacturing documentation, you'll be responsible for correcting this condition at no additional cost to the Government and no delivery schedule extension.

C13 Configuration Control Engineering Changes

(a) The Contractor may submit Engineering Change Proposal(s) (ECPs) and Request for Variance(s) (RFVs) for the requirements in the Government provided Technical Data Package (TDP). If a Value Engineering Change Proposal(s) (VECPs) clause is included on this contract, VECPs shall be submitted in the same manner as ECPs.

(1) ECPs - The Contractor may request a permanent change to the requirements specified in the TDP or any other baseline documentation by submitting an ECP. ECPs shall be submitted to include all Notice of Revisions (NORs) necessary to completely define the requested change. Each ECP shall be accompanied with at least one NOR per affected document. The Contractor shall not present any production items for acceptance that incorporate any change to the TDP or other baseline documentation until notified by the Government the ECP has been approved and incorporated in the contract.

(i) Page 1 of DD Form 1692 (or equivalent) shall be submitted for all ECPs. Pages 2-7 of DD Form 1692 shall be submitted when required to properly explain all the potential logistics and technical impacts of the proposed change. DD Form 1695 NOR or DD Form 1695-1 Tabulated NOR (or equivalents) shall be submitted to completely describe the desired change on each affected document.

(ii) All ECPs submitted by the Contractor will be routine priority unless otherwise justified. If the Contractor considers the ECP to be emergency or urgent, they shall include justification within 48 hours of submittal of the ECP.

(2) RFVs - The Contractor may request to temporarily depart from a requirement specified in the TDP or any other baseline documentation, by submitting an RFV. RFVs may be submitted either pre-production (formerly known as Request for Deviation (RFD)) or post-production and prior to acceptance by the Government (formerly known as Request for Waiver (RFW)). DD Form 1694 (or equivalent) shall be submitted for all RFVs. The Contractor shall not present any production items for acceptance with any nonconformance to the requirements in the TDP or other baseline documentation until notified by the Government the RFV has been approved and incorporated in the contract.

(b) Submission of requested changes - The submission of an ECP or RFV by the Contractor does not affect the required delivery dates specified within the contract, shall not constitute excusable delay in the performance of this Contract by the Contractor or in any way relieve the Contractor from compliance with the contract delivery schedule. If a delivery date change is needed, it must be negotiated with the Procuring Contracting Officer and documented via modification to the contract. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the Contract.

(c) Specifications - Permanent proposed changes to specifications which are part of the TDP or baseline documentation shall be requested with an ECP and NOR (i.e. Specification Change Notices (SCNs) are not required).

(d) Forms If any of the above listed forms are not included with the solicitation or contract, the Contractor may locate forms on the DOD Forms Website https://www.esd.whs.mil/Directives/forms/ or contact the Contract Specialist listed on page 1 of the solicitation or contract for copies of the forms.

D5 Packaging Requirements

D.5 Packaging Requirements (Specifications Standards)

(a) The preservation, packing, and marking requirements for this contract/order shall be accomplished in accordance with the requirements in the specification/standard defined below.

(b) The following requirements shall apply:

(1) LEVEL OF PRESERVATION: Military

(2) LEVEL OF PACKING: A

(3) QUANTITY PER UNIT PACKAGE: 001

(4) SPECIFICATION/STANDARD: MIL-PRF 32410

(c) The specification/standard cited is intended to give a clear and accurate description of the technical packaging requirements for the item being procured, including the procedure by which it can be determined that the requirements have been met. Specific instructions and/or tailoring of the specification/standard is detailed in the supplemental instructions below. Any design changes or changes in the method of preservation that provide a cost savings without degrading the method of preservation or packing and without affecting the serviceability of the item will be considered and responded to within 10 days of submission to PCO with copies to the ACO. The Government reserves the right to require testing to validate alternate industrial preservation methods, materials, blocking, bracing, cushioning, and packing.

(d) Marking:

In addition to any special markings called out by the specification/standard above, all unit packages, intermediate packs, exterior shipping containers, and, as applicable, unitized loads shall be marked in accordance with MIL-STD-129, The Contractor is responsible for application of special markings as discussed in the Military Standard regardless of whether specified in the contract/order or not. Special markings include, but are not limited to, Shelf-life markings, structural markings, and transportation special handling markings. The marking of pilferable and sensitive material will not identify the nature of the material.

NOTE: Passive RFID tagging is required in all contracts that contain DFARS clause 252.211- 7006. For details and most recent information, see http://www.acq.osd.mil/log/sci/ait.html (best viewed with Internet Explorer 11 or higher) for the current DoD Suppliers Passive RFID Information Guide and Supplier Implementation Plan. When an item has Unique Item Identifier (UII) markings as indicated by the inclusion of contract clause DFARS 252.211-7006, refer to the DoD Guide to Uniquely Identifying Items for development of the UII and MILSTD-129 for UII package marking requirements.

Contractors must verify the RFID and UII clauses cited above are included in this solicitation/contract.

(e) Heat Treatment and Marking of Wood Packaging Materials (WPM):

(1) In accordance with DOD 4140.65-M and the requirements of the International Standards for Phytosanitary Measures 15 (ISPM), Regulation of Wood Packaging Material in International Trade, current edition, (hereinafter ISPM 15), the following commercial heat treatment and marking process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood Packaging Material (WPM). Foreign manufacturers shall comply with ISPM 15, and have the WPM heat treatment and marking verified in accordance with their National Plant Protection Organizations compliance program.

(2) Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All WPM using a conventional steam or dry kiln heat chamber (treatment code for the mark: HT) shall be heat treated to a minimum core temperature of 56 degrees Celsius for a minimum of 30 minutes, and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org ). WPM heat treated wood using dielectric heating (treatment code for the mark: DH) shall follow the requirements in ISPM 15, and shall be certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure the materials used in manufacture can be traced to the original source of heat treatment, and that the original source of the heat treatment obtained the necessary certifications.

(3) Marking. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention

Standard. The ALSC approved quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens.

Pallet markings shall be applied to the side of the stringer or end of the block on diagonally opposite sides and ends of the pallet and be contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ALSC approved DUNNAGE stamp.

(f) Hazardous Materials (As applicable):

4) NSN 8150-01-483-9115, QUADCON Double doors on one side

8150-01-483-9115

CONTAINER, QUADCON

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER

LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS,

THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A

SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE

THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES

CONTAINER SHALL BE NEW OR ONE-TIME USED*. CONTAINER SHALL NOT EXCEED ONE

YEAR FROM THE DATE OF MANUFACTURE.

DIMENSIONS: 4' 9-3/8" LENGTH X 8' WIDTH X 6' 10" HEIGHT.

CORRUGATED STEEL SIDES, ROOF, AND SWING DOORS ON CURB SIDE. HEAVY DUTY

STEEL FLOOR.

4-WAY FORKLIFT POCKETS, VENTS (2), WALL TIE DOWN STEEL LASHING RINGS (16),

CORNER POST TIE DOWNS (20), CONNECTING COUPLERS (3), CONNECTING COUPLER

STORAGE BRACKET (1), ADJUSTABLE SHELVING BRACKETS (5 SETS).

MANIFEST BOX (2).

ANTI-PILFERAGE PROVISIONS.

MAXIMUM TARE WEIGHT 2,080 LBS, MAXIMUM GROSS WEIGHT 11,200 LBS. FOUR

QUADCONS, WHEN COUPLED TOGETHER, WILL FORM A 20' ISO-COMPATIBLE

CONTAINER.

MANUFACTURED TO THE LASTEST REVISION OF ISO 668, ISO 1161, ISO 1496-1, ISO 6346

& ISO 830.

MUST BE CERTIFIABLE TO INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC)

BY TIME OF AWARD AND INTERNATIONAL MARITIME DANGEROUS GOODS (IMDG)

STANDARDS. CONTAINER SHALL BE INSPECTED TO VERIFY COMPLIANCE WITH MIL-STD-

209, MIL-STD-810, MIL-STD-1366 AND MIL-STD-1472.

COLOR GREEN # 34094 UNLESS SPECIFIED BY THE CUSTOMER. NON-CARC PAINT

COPIES OF ISO STANDARDS ARE AVAILABLE FROM THE AMERICAN NATIONAL

STANDARDS INSTITUTE (ANSI). USE URL WWW.ANSI.ORG

COPY OF INTERNATIONAL CONVENTION FOR SAFE CONTAINERS (CSC) IS AVAILABLE

FROM URL WWW.IMO.ORG

IAW BASIC DRAWING NR 14153 RE-014839115

REVISION NR DTD 08/10/2015

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-209K

REVISION NR K DTD 02/22/2005

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-810H

REVISION NR H DTD 01/31/2019

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1366E

REVISION NR E DTD 10/31/2006

PART PIECE NUMBER:

IAW REFERENCE STD NR MIL-STD-1472H

5) NSN 8150-01-527-2872, QUADCON Double doors on both sides (CARC paint)

CONTAINER, QUADCON, CARC

Description/Specs./Work Statement

PROCUREMENT DOCUMENTATION TITLE:

ATPD-2338C

Packaging and Marking

PACKAGING/PACKING/SPECIFICATIONS:

See packaging requirements clause

Unit Pack: 001

Level Preservation: Military

Level Packing: A

The below clauses apply to this NSN 8150-01-527-2872:

52.246-4053 (TACOM) USE OF MIL-STD 1916 (JAN 2001)

The Government will not accept lots whose samples submitted for acceptance contain nonconformances unless appropriately documented and approved by the contracting officer. The contractor shall use MIL-STD-1916, DOD Preferred Methods of Acceptance of Product. The Verification Level (VL) shall be VL IV for major characteristics and VL II for minor characteristics. MIL-HDBK-1916 provides guidance on the use of MIL-STD-1916.

52.211-4015 (TACOM/ARDEC) CONFIGURATION CONTROL- ENGINEERING CHANGES (JAN

2016)

(a) The contractor may submit Engineering Change Proposal(s) (ECPSs) and Request for Variance(s) (RFVs) for the requirements in the Government provided Technical Data Package (TDP). If a Value Engineering Change Proposal(s) (VECPs) clause is included on this contract, VECPs shall be submitted in the same manner as ECPs.

(1) ECPs- The contractor may request a permanent change to the requirement specified in the TDP or any other baseline documentation by submitting an ECP.

ECPs shall be submitted to include all NORs necessary to completely define the requested change. Each ECP shall be accompanied with at least one NOR per affected document. The contractor shall not present any production items for acceptance that incorporate any change to the TDP or other baseline documentation until notified by the Government the ECP has been approved and incorporated in the contract.

(i) Page 1 of DD Form 1692 (or equivalent) shall be submitted for all ECPs. Pages 2- 7 of DD Form 1692 shall be submitted when required to properly explain all the potential logistics and technical impacts of the proposed change. DD Form 1695 NOR or DD Form 1695-1 Tabulated NOR (or equivalents) shall be submitted to completely describe the desired change on each affected document.

(ii) All ECPs submitted by the contractor will be routine priority unless otherwise justified. If the contractor considers the ECP to be emergency or urgent, they shall include justification within 48 hours of submittal of the ECP.

(2) RFVs- The contractor may request to temporarily depart from a requirement specified in the TDP or any other baseline documentation, by submitting and RFV.

RFVs may be submitted either pre-production (formerly known as Request for Deviation (RFD)) or post-production and prior to acceptance by the Government (formerly known as request for waiver (RFW)). DD Form 1694 (or equivalent) shall be submitted for all RFVs. The contractor shall not present any production items for acceptance with any nonconformance to the requirements in the TDP or other baseline documentation until notified by the Government the RFV has been approved and incorporated in the contract.

(b) Submission of requested changes- The submission of an ECP or RFV by the Contractor does not affect the required delivery dates specified within the contract, shall not constitute excusable delay in the performance of this contract by the contractor or in any way relieve the contractor from compliance with the contract delivery schedule. If a delivery date change is needed, it must be negotiated with the Contracting Officer and documented via modification to the contract. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the contract.

(c) Specification- Permanent proposed changes to specifications which are part of the TDP or baseline documentation shall be requested with an ECP and NOR (i.e. Specification Changes Notices (SCNs) are not required).

(d) Forms If any of the above listed forms are not included with the solicitation or contract, the contractor may locate forms on the DOD Forms Website (https://www.esd.whs.mil/Directives/forms/) or contract the contract specialist listed on page 1 of the solicitation or contract for copies of the forms

52.211-4516 (TACOM) PACKAGING REQUIRMENTS (SELECTIVE GROUP PACKAGING

REQUIREMENTS)(DEC 2014)

(a) Military Preservation, packing, and marking for this contract shall be accomplished in accordance with the specific requirements identified below and all the applicable requirements of MIL-STD-2073-1.

(1) Level of Preservation: Military

(2) Level of Packing: A

(3) Quantity Per Unit Package: 001

(b) MIL-STD-2073-1, Appendix J establishes and defines codes used in describing military packaging methods and materials. The following codes from Appendix J apply:

Preservation: ZZ (Table j.1. and j.ia)

Cleaning procedure code: 1 (Table j.ii) Preservative Material Code: 00 (Zero) (Table j.iii) Wrapping Material Code: 00 (Zero) (Table j.iv) Cushioning and Dunnage Code: 00 (Zero) (Table j.v) Thickness of Cushioning or Dunnage Code: 0 (Zero) (Table j.vi) Unit Container Code: 00 (Zero) (Table j.vii) Intermediate Container Code: 00 (Zero) (Table j.vii) Quantity Per Intermediate Container Code: AAA (Appendix J.4.11) Packing Code: F (Table j.IX and J.IXa) Special Marking Code: 00 (Zero) (Table j.x)

(c) Unitization: Shipment of identical items going to the same destination shall be palletized if they have a total cubic displacement of 50 cubic feet or more unless skids or other forklift handling features are included on the containers. Pallet loads must be stable, and to the greatest extent possible, provide a level top for ease of stacking. A palletized load shall be of a size to allow for placement of two loads high and wide in a conveyance.

The weight capacity of the pallet must be adequate for the load. The preferred pallet is a 40 x 48 inch, 4-way entry pallet although variations may be permitted as dictated by the characteristics of the items being unitized. The load shall be contained in a manner that will permit safe handling during shipment and storage.

(d) Marking:

(1) All unit packages, intermediate packs, exterior shipping containers, and, as applicable, unitized loads shall be marked in accordance with MIL-STD-129, Revision R, including bar coding and Military Shipment Label (MSL). The contractor is responsible for application of special markings as discussed in the Military Standard regardless of whether specified in the contract or not. Special markings include, but are not limited to, Shelf-life markings, structural markings, and transportation special handling markings. The marking of pilferable and sensitive material will not identify the nature of the material. Passive RFID tagging is required in all contracts that contain DFARS clause 252.211-7006. Contractors must check the solicitation and/or contract for this clause. For details and most recent information, see http://www.acq.osd.mil/log/sci/ait.html for the current DoD Suppliers Passive RFID Information Guide. When an item is assigned Unique Item Identifier (UII) markings as indicated by the inclusion of contract clause DFARS 252.211-7003, refer to the DoD Guide to Uniquely Identifying Items (available at http://dodprocurementtoolbox.com/page/unique-id/tools ) for development of the UII and

MIL-STD-129, Revision R for UII package marking requirements. Contractors must verify the RFID and UII clauses cited above are included in this solicitation/contract.

(e) Heat Treatment and Marking of Wood Packaging Materials (WPM):

(1) In accordance with DOD 4140.625-M and the requirements of the International Standards for Phytosanitary Measures 15 (ISPM), Regulation of Wood Packaging Material in International Trade, current edition, (hereinafter ISPM 15), the following commercial heat treatment and marking process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood Packaging Material (WPM). Foreign manufacturers shall comply with ISPM 15, and have the WPM heat treatment and marking verified in accordance with their National Plant Protection Organizations compliance program.

(2) Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All WPM using a conventional steam or dry kiln heat chamber (treatment code for the mark: HT) shall be heat treated to a minimum core temperature of 56 degrees Celsius for a minimum of 30 minutes, and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org). WPM heat treated wood using dielectric heating (treatment code for the mark: DH) shall follow the requirements in ISPM 15, and shall be certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure the materials used in manufacture can be traced to the original source of heat treatment, and that the original source of the heat treatment obtained the necessary certifications.

(3) Marking. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The ALSC approved quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the side of the stringer or end of the block on diagonally opposite sides and ends of the pallet and be contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ALSC approved DUNNAGE stamp.

(f) These packaging requirements are intended to provide protection against environmentally induced corrosion and deterioration, physical and mechanical damage, and other forms of degradation during storage, multiple handling, and shipment associated with the military distribution system. The Government encourages contractors to submit requests for changes that will result in savings or improve the packaging. Please submit request for changes in accordance with the RFD clause of the contract. Government reserves the right to require testing to validate alternate industrial preservation methods, materials, blocking, bracing, cushioning, and packing at contractor’s expense.

(g) Hazardous Materials(as applicable):

(1) Hazardous Materials is defined as a substance or waste which has been determined by the Secretary of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and which has been so designated.

(This includes all items listed as hazardous in Titles 29, 40 and 49 CFR and other applicable modal regulations effective at the time of shipment.)

(2) Packaging and marking for hazardous material shall comply with the requirements herein for the mode of transport and the applicable performance packaging contained in the following documents: - International Air Transport Association (IATA) Dangerous Goods Regulations - International Maritime Dangerous Goods Code (IMDG) - Code of Federal Regulations (CFR) Title 29, Title 40 and Title 49 - Joint Service Regulation AFJMAN24- 204(I)/TM38-250/NAVSUPPUB 505/MCO P4030.19(I)/DLAM 4145.3(I) (for military air shipments).

(3) If the shipment originates from outside the continental United States, the shipment shall be prepared in accordance with the United Nations Recommendations on the Transport of Dangerous Goods in a manner acceptable to the Competent Authority of the nation of origin and in accordance with regulations of all applicable carriers. A Product Material Safety Data Sheets (MSDS) is required to be included with every unit pack and intermediate container and shall be included with the packing list inside the sealed pouch attached to the outside of the package.

(h) SUPPLEMENTAL INSTRUCTIONS: STEEL STORAGE CONTAINER, NO MOP REQUIRED [End of Clause]

52.211-4029 INTERCHANGEABILITY OF COMPONENTS MAY/1994 (TACOM)

(a) DESIGN CHANGES TO ITEMS NOT UNDER GOV'T DESIGN CONTROL. Once the Government accepts the first production test item, or ______________________________________________________ accepts the first end item you deliver, (whichever comes first) you must not make design changes to any item or part that is not under Government design control.

(b) WHEN THE POLICY CAN BE WAIVED. The Procuring Contracting Officer (PCO) will consider waiving this policy at your request. If _____________________________ your request reaches the PCO after the first production item test has been performed, then we may conduct another first production test at your expense. (c) PRODUCTION OR DELIVERY DELAYS. Any production or delivery delays caused by this retesting will not be the basis for:

_____________________________ (1) an "excusable delay" as defined in the DEFAULT clause of this contract. (2) be the basis for an increase in contract price or delivery schedule extension. [End of clause]

252.211-7005 SUBSTITUTIONS FOR MILITARY OR FEDERAL SPECIFICATIONS AND

STANDARDS NOV/2005

(a) Definition. SPI process, as used in this clause, means a management or manufacturing process that has been accepted previously by the Department of Defense under the Single Process Initiative (SPI) for use in lieu of a specific military or Federal specification or standard at specific facilities. Under SPI, these processes are reviewed and accepted by a Management Council, which includes representatives of the Contractor, the Defense Contract Management Agency, the Defense Contract Audit Agency, and the military departments.

(b) Offerors are encouraged to propose SPI processes in lieu of military or Federal specifications and standards cited in the solicitation. A listing of SPI processes accepted at specific facilities is available via the Internet at http://guidebook.dcma.mil/20/guidebook_process.htm (paragraph 4.2).

(c) An offeror proposing to use an SPI process in lieu of military or Federal specifications or standards cited in the solicitation shall

(1) Identify the specific military or Federal specification or standard for which the SPI process has been accepted;

(2) Identify each facility at which the offeror proposes to use the specific SPI process in lieu of military or Federal specifications or standards cited in the solicitation;

(3) Identify the contract line items, subline items, components, or elements affected by the SPI process; and

(4) If the proposed SPI process has been accepted at the facility at which it is proposed for use, but is not yet listed at the Internet site specified in paragraph (b) of this clause, submit documentation of Department of Defense acceptance of the SPI process. (d) Absent a determination that an SPI process is not acceptable for this procurement, the Contractor shall use the following SPI processes in lieu of military or Federal specifications or standards: (Offeror insert information for each SPI process) SPI Process: N/A ______ Facility: ________________________________ Military or Federal Specification or Standard:

________________________________ Affected Contract Line Item Number, Subline Item Number, Component, or Element: ______________________________ (e) If a prospective offeror wishes to obtain, prior to the time specified for receipt of offers, verification that an SPI process is an acceptable replacement for military or Federal specifications or standards required by the solicitation, the prospective offeror (1) May submit the information required by paragraph (d) of this clause to the Contracting Officer prior to submission of an offer; but (2) Must submit the information to the Contracting Officer at least 10 working days prior to the date specified for receipt of offers. (End of clause)

6) NSN 8150-01-528-7550, QUADCON Double doors on both sides (Non-CARC paint)

CONTAINER, QUADCON, NON-CARC

Description/Specs./Work Statement

PROCUREMENT DOCUMENTATION TITLE:

ATPD-2338C

Packaging and Marking

Packaging/Packing/Specifications:

See packaging requirements clause

Level Preservation: Military

Level Packing: A

The below clauses apply to this NSN 8150-01-528-7550

52.246-4053 (TACOM) USE OF MIL-STD 1916 (JAN 2001)

The Government will not accept lots whose samples submitted for acceptance contain nonconformances unless appropriately documented and approved by the contracting officer. The contractor shall use MIL-STD-1916, DOD Preferred Methods of Acceptance of Product. The Verification Level (VL) shall be VL IV for major characteristics and VL II for minor characteristics. MIL-HDBK-1916 provides guidance on the use of MIL-STD-1916.

52.211-4015 (TACOM/ARDEC) CONFIGURATION CONTROL- ENGINEERING CHANGES (JAN

2016)

(a) The contractor may submit Engineering Change Proposal(s) (ECPSs) and Request for Variance(s) (RFVs) for the requirements in the Government provided Technical Data Package (TDP). If a Value Engineering Change Proposal(s) (VECPs) clause is included on this contract, VECPs shall be submitted in the same manner as ECPs.

(1)ECPs- The contractor may request a permanent change to the requirement specified in the TDP or any other baseline documentation by submitting an ECP. ECPs shall be submitted to include all NORs necessary to completely define the requested change. Each ECP shall be accompanied with at least one NOR per affected document. The contractor shall not present any production items for acceptance that incorporate any change to the TDP or other baseline documentation until notified by the Government the ECP has been approved and incorporated in the contract.

(i)Page 1 of DD Form 1692 (or equivalent) shall be submitted for all ECPs. Pages 2-7 of DD Form 1692 shall be submitted when required to properly explain all the potential logistics and technical impacts of the proposed change. DD Form 1695 NOR or DD Form 1695-1 Tabulated NOR (or equivalents) shall be submitted to completely describe the desired change on each affected document.

(ii)All ECPs submitted by the contractor will be routine priority unless otherwise justified. If the contractor considers the ECP to be emergency or urgent, they shall include justification within 48 hours of submittal of the ECP.

(2)RFVs- The contractor may request to temporarily depart from a requirement specified in the TDP or any other baseline documentation, by submitting an RFV. RFVs may be submitted either pre-production (formerly known as Request for Deviation (RFD)) or post-production and prior to acceptance by the Government (formerly known as request for waiver (RFW)). DD Form 1694 (or equivalent) shall be submitted for all RFVs. The contractor shall not present any production items for acceptance with any nonconformance to the requirements in the TDP or other baseline documentation until notified by the Government the RFV has been approved and incorporated in the contract.

(b) Submission of requested changes- The submission of an ECP or RFV by the Contractor does not affect the required delivery dates specified within the contract, shall not constitute excusable delay in the performance of this contract by the contractor or in any way relieve the contractor from compliance with the contract delivery schedule. If a delivery date change is needed, it must be negotiated with the Contracting Officer and documented via modification to the contract. The submission of an ECP and/or RFV by the Contractor shall not preclude the Government from exercising its rights under any clause of the contract.

(c) Specification- Permanent proposed changes to specifications which are part of the TDP or baseline documentation shall be requested with an ECP and NOR (i.e. Specification Changes Notices (SCNs) are not required).

(d) Forms If any of the above listed forms are not included with the solicitation or contract, the contractor may locate forms on the DOD Forms Website (https://www.esd.whs.mil/Directives/forms/) or contract the contract specialist listed on page 1 of the solicitation or contract for copies of the forms

52.211-4516 (TACOM) PACKAGING REQUIRMENTS (SELECTIVE GROUP PACKAGING

REQUIREMENTS)(DEC 2014)

(a) Military Preservation, packing, and marking for this contract shall be accomplished in accordance with the specific requirements identified below and all the applicable requirements of MIL-STD-2073-1.

(1) Level of Preservation: Military

(2) Level of Packing: A

(3) Quantity Per Unit Package: 001

(b) MIL-STD-2073-1, Appendix J establishes and defines codes used in describing military packaging methods and materials. The following codes from Appendix J apply:

Preservation: ZZ (Table j.1. and j.ia) Cleaning procedure code: 1 (Table j.ii) Preservative Material Code: 00 (Zero) (Table j.iii) Wrapping Material Code: 00 (Zero) (Table j.iv) Cushioning and Dunnage Code: 00 (Zero) (Table j.v) Thickness of Cushioning or Dunnage Code: 0 (Zero) (Table j.vi) Unit Container Code: 00 (Zero) (Table j.vii) Intermediate Container Code: 00 (Zero) (Table j.vii) Quantity Per Intermediate Container Code: AAA (Appendix J.4.11) Packing Code: F (Table j.IX and J.IXa) Special Marking Code: 00 (Zero) (Table j.x)

(c) Unitization: Shipment of identical items going to the same destination shall be palletized if they have a total cubic displacement of 50 cubic feet or more unless skids or other forklift handling features are included on the containers. Pallet loads must be stable, and to the greatest extent possible, provide a level top for ease of stacking. A palletized load shall be of a size to allow for placement of two loads high and wide in a conveyance.

The weight capacity of the pallet must be adequate for the load. The preferred pallet is a 40 x 48 inch, 4-way entry pallet although variations may be permitted as dictated by the characteristics of the items being unitized. The load shall be contained in a manner that will permit safe handling during shipment and storage.

(d) Marking:

(1) All unit packages, intermediate packs, exterior shipping containers, and, as applicable, unitized loads shall be marked in accordance with MIL-STD-129, Revision R, including bar coding and Military Shipment Label (MSL). The contractor is responsible for application of special markings as discussed in the Military Standard regardless of whether specified in the contract or not. Special markings include, but are not limited to, Shelf-life markings, structural markings, and transportation special handling markings. The marking of pilferable and sensitive material will not identify the nature of the material. Passive RFID tagging is required in all contracts that contain DFARS clause 252.211-7006. Contractors must check the solicitation and/or contract for this clause. For details and most recent information, see http://www.acq.osd.mil/log/sci/ait.html for the current DoD Suppliers Passive RFID Information Guide. When an item is assigned Unique Item Identifier (UII) markings as indicated by the inclusion of contract clause DFARS 252.211-7003, refer to the DoD Guide to Uniquely Identifying Items (available at http://dodprocurementtoolbox.com/page/unique-id/tools ) for development of the UII and MIL-STD-129, Revision R for UII package marking requirements. Contractors must verify the RFID and UII clauses cited above are included in this solicitation/contract.

(e) Heat Treatment and Marking of Wood Packaging Materials (WPM):

(1) In accordance with DOD 4140.625-M and the requirements of the International Standards for Phytosanitary Measures 15 (ISPM), Regulation of Wood Packaging Material in International Trade, current edition, (hereinafter ISPM 15), the following commercial heat treatment and marking process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood Packaging Material (WPM). Foreign manufacturers shall comply with ISPM 15, and have the WPM heat treatment and marking verified in accordance with their National Plant Protection Organizations compliance program.

(2) Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All WPM using a conventional steam or dry kiln heat chamber

(treatment code for the mark: HT) shall be heat treated to a minimum core temperature of 56 degrees Celsius for a minimum of 30 minutes, and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org). WPM heat treated wood using dielectric heating (treatment code for the mark: DH) shall follow the requirements in ISPM 15, and shall be certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see URL: http://www.alsc.org). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure the materials used in manufacture can be traced to the original source of heat treatment, and that the original source of the heat treatment obtained the necessary certifications.

(3) Marking. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The ALSC approved quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the side of the stringer or end of the block on diagonally opposite sides and ends of the pallet and be contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ALSC approved DUNNAGE stamp.

(f) These packaging requirements are intended to provide protection against environmentally induced corrosion and deterioration, physical and mechanical damage, and other forms of degradation during storage, multiple handling, and shipment associated with the military distribution system. The Government encourages contractors to submit requests for changes that will result in savings or improve the packaging. Please submit request for changes in accordance with the RFD clause of the contract. Government reserves the right to require testing to validate alternate industrial preservation methods, materials, blocking, bracing, cushioning, and packing at contractor’s expense.

(g) Hazardous Materials(as applicable):

(1) Hazardous Materials is defined as a substance or waste which has been determined by the Secretary of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and which has been so designated.

(This includes all items listed as hazardous in Titles 29, 40 and 49 CFR and other applicable modal regulations effective at the time of shipment.)

(2) Packaging and marking for hazardous material shall comply with the requirements herein for the mode of transport and the applicable performance packaging contained in the following documents: - International Air Transport Association (IATA) Dangerous Goods

Regulations - International Maritime Dangerous Goods Code (IMDG) - Code of Federal Regulations (CFR) Title 29, Title 40 and Title 49 - Joint Service Regulation AFJMAN24- 204(I)/TM38-250/NAVSUPPUB 505/MCO P4030.19(I)/DLAM 4145.3(I) (for military air shipments).

(3) If the shipment originates from outside the continental United States, the shipment shall be prepared in accordance with the United Nations Recommendations on the Transport of Dangerous Goods in a manner acceptable to the Competent Authority of the nation of origin and in accordance with regulations of all applicable carriers. A Product Material Safety Data Sheets (MSDS) is required to be included with every unit pack and intermediate container and shall be included with the packing list inside the sealed pouch attached to the outside of the package.

(h) SUPPLEMENTAL INSTRUCTIONS: STEEL STORAGE CONTAINER, NO MOP REQUIRED

52.211-4029 INTERCHANGEABILITY OF COMPONENTS MAY/1994 (TACOM)

(a) DESIGN CHANGES TO ITEMS NOT UNDER GOV'T DESIGN CONTROL. Once the Government accepts the first production test item, or ______________________________________________________ accepts the first end item you deliver, (whichever comes first) you must not make design changes to any item or part that is not under Government design control.

(b) WHEN THE POLICY CAN BE WAIVED. The Procuring Contracting Officer (PCO) will consider waiving this policy at your request. If _____________________________ your request reaches the PCO after the first production item test has been performed, then we may conduct another first production test at your expense. (c) PRODUCTION OR DELIVERY DELAYS. Any production or delivery delays caused by this retesting will not be the basis for:

_____________________________ (1) an "excusable delay" as defined in the DEFAULT clause of this contract. (2) be the basis for an increase in contract price or delivery schedule extension. [End of clause]

252.211-7005 SUBSTITUTIONS FOR MILITARY OR FEDERAL SPECIFICATIONS AND

STANDARDS NOV/2005

(a) Definition. SPI process, as used in this clause, means a management or manufacturing process that has been accepted previously by the Department of Defense under the Single Process Initiative (SPI) for use in lieu of a specific military or Federal specification or standard at specific facilities. Under SPI, these processes are reviewed and accepted by a

Management Council, which includes representatives of the Contractor, the Defense Contract Management Agency, the Defense Contract Audit Agency, and the military departments.

(b) Offerors are encouraged to propose SPI processes in lieu of military or Federal specifications and standards cited in the solicitation. A listing of SPI processes accepted at specific facilities is available via the Internet at http://guidebook.dcma.mil/20/guidebook_process.htm (paragraph 4.2).

(c) An offeror proposing to use an SPI process in lieu of military or Federal specifications or standards cited in the solicitation shall

(1) Identify the specific military or Federal specification or standard for which the SPI process has been accepted;

(2) Identify each facility at which the offeror proposes to use the specific SPI process in lieu of military or Federal specifications or standards cited in the solicitation;

(3) Identify the contract line items, subline items, components, or elements affected by the SPI process; and

(4) If the proposed SPI process has been accepted at the facility at which it is proposed for use, but is not yet listed at the Internet site specified in paragraph (b) of this clause, submit documentation of Department of Defense acceptance of the SPI process. (d) Absent a determination that an SPI process is not acceptable for this procurement, the Contractor shall use the following SPI processes in lieu of military or Federal specifications or standards: (Offeror insert information for each SPI process) SPI Process: N/A ______ Facility: ________________________________ Military or Federal Specification or Standard:

________________________________ Affected Contract…