PID_SPE7LX-18-R-0125.docx

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:014247363

PARTS KIT, MIRROR ASSEMBLY, L.H., REARVIEW

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RQ016

REFERENCE NUMBER:RT001

REFERENCE NUMBER:RQ006

FOR THE PURPOSE OF CLARIFICATION THE TERMINOLOGY

"FIRST ARTICLE" SHALL REPLACE "INITIAL PRODUCTION

APPROVAL" AND "INITIAL PRODUCTION INSPECTION" IN

ALL APPLICABLE SPECIFICATIONS AND DRAWINGS REFERENCED.

CONTRACTOR FIRST ARTICLE TESTING APPLIES PER DWG'S:

12342131, 12342133, AND QAP 12342133

5 SAMPLE UNITS PROVIDED FOR TESTING; NOTIFY 30

DAYS BEFORE; ACO APPROVAL; 30 DAYS GOVERNMENT

REVIEW; 120 DAYS TO SUBMIT. WILL NOT RETURN 2

SAMPLES DUE TO DESTRUCTIVE TESTING, SHALL SERVE

AS A MANUFACTURING STANDARD.

REFERENCE NUMBER:CS187

REFERENCE NUMBER:CQ042

REFERENCE NUMBER:CQ044

REFERENCE NUMBER:CQ015

REFERENCE NUMBER:CS060

REFERENCE NUMBER:CS147

REFERENCE NUMBER:ZD080

REFERENCE NUMBER:CS241

REFERENCE NUMBER:CS001

*NOTICE: FIRST ARTICLE TESTING DOES NOT RELIEVE THE

CONTRACTOR OF THE RESPONSIBILITY OF MEETING ALL DRAWING

AND TECHNICAL DATA REQUIREMENTS REQUIRED BY CONTRACT.

*NOTICE: SUPPLIERS ARE REQUIRED TO IDENTIFY SUBCONTRACTORS

AT TIME OF QUOTING IF KNOWN. USE OF ANY SUB-CONTRACTOR

SUPPLIER WILL REQUIRE JCP CERTIFICATION APPROVAL.

*THIS NSN REQUIRES GOVERNMENT SOURCE INSPECTION (GSI)<(>,<)>

WITH A FIRST ARTICLE TEST (FAT) REQUIREMENT. THE GSI

REQUIREMENT IS VALID WHETHER OR NOT THE FIRST ARTICLE

TEST REQUIREMENT IS INVOKED.

REFERENCE NUMBER:RQ027

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 19207 57K3213

REVISION NR A DTD 07/26/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 24617 F-1.101M

REVISION NR DTD 03/01/1977

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12440109

REVISION NR A DTD 07/25/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12342139

REVISION NR D DTD 01/30/2009

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12343061

REVISION NR C DTD 10/10/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12343062

REVISION NR C DTD 10/07/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12343063

REVISION NR C DTD 10/07/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12369021

REVISION NR C DTD 05/14/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12342131

REVISION NR F DTD 01/30/2009

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12342132

REVISION NR G DTD 01/30/2009

PART PIECE NUMBER:

IAW REFERENCE QAP 19207 12342133

REVISION NR D DTD 03/14/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12342133

REVISION NR F DTD 04/24/2009

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12369001

REVISION NR D DTD 05/14/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 24617 F-15.101

REVISION NR DTD 08/01/1968

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12446871

REVISION NR Y DTD 09/26/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12480726

REVISION NR DTD 08/23/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12480727

REVISION NR DTD 08/23/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12480693

REVISION NR A DTD 11/07/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12480715

REVISION NR DTD 08/09/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 57K3213

REVISION NR DTD 01/28/2014

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ

WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z

UNIT CONT:ZZ OPI:M

INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:ZZ -ZZ Special Requirements

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

REFERENCE NUMBER:CS259

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND

NON-MANUFACTURERS)

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RQ016

RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS

LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A

SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR

QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN

PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED

MANUFACTURERS LIST (QML)" APPLY.

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT

REFERENCE NUMBER RQ006

RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS

REFERENCE NUMBER CS187

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

REFERENCE NUMBER CQ042

THIS NSN REQUIRES GOVERNMENT SOURCE INSPECTION

WITH A FIRST ARTICLE TEST REQUIREMENT. THE

GOVERNMENT SOURCE INSPECTION REQUIREMENT IS

VALID WHETHER OR NOT THE FIRST ARTICLE TEST

REQUIREMENT IS INVOKED.

REFERENCE NUMBER CQ044

ATTENTION BUYER, FIRST ARTICLE APPROVAL

AUTHORITY IS DELEGATED TO DCMA. INCLUDE

CLAUSE I09C08 (DELEGATION OF AUTHORITY

FOR FIRST ARTICLE APPROVAL) WITH THE AWARD.

REFERENCE NUMBER CQ015

"FINAL INSPECTION AND ACCEPTANCE OF THE ITEM

SHALL BE AT THE ACTUAL MANUFACTURING FACILITY.

TECHNICAL INSPECTION IS REQUIRED. THE

CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL

INFORMATION AVAILABLE TO VERIFY THAT THE ITEM

MEETS ALL TECHNICAL REQUIREMENTS.

COUNT, KIND, AND CONDITION INSPECTIONS ARE

NOT ACCEPTABLE. THIS NOTE TAKES PRECEDENCE OVER

MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6,

QUOTATIONS BY NON-MANUFACTURERS (APR 1984,

DCSC 52.217-9C01). FINAL INSPECTION OF

PACKAGING, IF REQUIRED, MAY BE CONDUCTED

ELSEWHERE."

REFERENCE NUMBER CS060

THE ITEM DESCRIBED IN THIS SOLICITATION

IS DEFINED IN WHOLE OR IN PART BY ARMY

DRAWING(S). THESE DRAWING(S) MAY CONTAIN

A PAINT FINISHING REQUIREMENT. WHERE SUCH

REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING

16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE-

MENTS OF THE ARMY DRAWING(S). THIS DRAWING

CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT

RESISTANT COATINGS (CARC), AND ADDITIONAL

INFORMATION RELATING TO HIGH TEMPERATURE

COATINGS.

REFERENCE NUMBER CS147

"THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH

MUST CONFORM TO SOURCE CONTROL DRAWING. BY

SUBMITTING AN OFFER, THE OFFEROR AGREES TO

PROVIDE SOURCE CONTROLLED COMPONENTS FROM

SOURCES APPROVED ON THE APPLICABLE SOURCE

CONTROL DRAWING."

REFERENCE NUMBER ZD080

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

REFERENCE NUMBER CS241

NOTE: THIS IS A RESTRICTED SOURCE ITEM AND

REQUIRES ENGINEERING SOURCE APPROVAL BY THE

GOVERNMENT DESIGN CONTROL ACTIVITY.

REFERENCE NUMBER CS001

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND

ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH

JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF

STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL

AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL

TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB

ADDRESS:

https://public.logisticsinformationservice.dla.mil/PublicHome/jcp/defaul t.aspx

OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF

GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE

REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT

OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE

EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25.

REFERENCE NUMBER RQ027

A. Data required by this document will be included in the price of the procured item(s).

B. The supplier shall prepare and furnish one (1) copy of the Certificate of Quality Compliance (COQC) for all delivered supplies. If the supplies delivered under this contract are from more than one manufacturing lot, a separate one (1) copy of the COQC shall be prepared and furnished for each manufacturing lot represented by, manufactured or produced under a product specification, original equipment manufacturer (OEM)/manufacturer's part number, commercial, industry or military standard, or drawings, or other technical data. Each Certificate shall be prepared in accordance with the Supplemental Quality Assurance Provision (SQAP).

C. For contracts assigned for Government inspection at source, the supplier shall have the completed Certificate available for review by the Government representative when the material is presented for acceptance by the Government. The Government representative can sign off on the WAWF receiving report so long as the Contractor complied with the COQC and the documentation is uploaded as an attachment to the Production CLIN in iRAPT.

D. An electronic copy of each COQC, for Government records retention, shall be entered into the Invoicing, Receipt, Acceptance and Property Transfer (iRAPT) system by the supplier via the Attachment tab of the Receiving Report (RR). Instructions for entering Attachments can be found in the iRAPT - Web Based Training Main Menu under "Attachments which can be viewed at https://wawfraid.nit.disa.mil/wawfwbt/xhtml/unaut h/web/wbt/wawfra/Attachments.xhtml. If the supplier offering the material to the Government is not the manufacturer of the material, the supplier is responsible for obtaining a certified test report from the manufacturer, including it as part of this COQC, and for demonstrating that the specific material being offered under this Certificate is covered by the certified test report. The data submittal listed above is in addition to the other iRAPT requirements included in this contract. Whenever access to the iRAPT system is limited or not available, the supplier shall notify the PCO and request permission to submit documents manually until the iRAPT system is again available for use. Unless otherwise specified by the contract, the supplier shall be responsible for retaining the Certificate for a period of 4 years. When requested by the Contracting Officer, the supplier shall make the Certificate available for review by the Government at any time during the period the Certificate is required to be retained.

E. No Certificate of Conformance (COC) or alternate release is authorized.

End of Requirement

REFERENCE NUMBER CS259

"PRESERVATION & PACKAGING SHALL BE

I/A/W THE LATEST REVISION OF MILITARY

SPECIFICATION MIL-STD-2073-1 APPENDIX D,

FOR PACKAGING OF "KITS".