PIDPACK.docx

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:010957437

ROLLER, BEARING.

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

IDENTIFY TO:

REFERENCE NUMBER:A0003

CONTRACTOR FIRST ARTICLE:

REFERENCE NUMBER:ZD042

SAMPLE SIZE: 1 PIECE

BEARING RESTRICTION:

REFERENCE NUMBER:A1166

EXPORT CONTROL:

REFERENCE NUMBER:CS001

REFERENCE NUMBER:ZD074

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 78286 70217-02723

REVISION NR A4 DTD 06/19/1984

PART PIECE NUMBER: 70217-02723-041

IAW REFERENCE DRAWING NR 78286 70217-02723

REVISION NR A DTD 09/18/2006

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8423

REVISION NR 05 DTD 07/08/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8798

REVISION NR 17 DTD 04/28/2015

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS4011

REVISION NR 5 DTD 11/27/2012

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 70217-02723

REVISION NR AH DTD 04/05/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81996 70217-02723

REVISION NR F DTD 10/01/2015

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8747

REVISION NR 3 DTD 01/23/2008

PART PIECE NUMBER:

IAW REFERENCE QAP 13873 QAP-B02

REVISION NR B DTD 12/11/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8423

REVISION NR 5- DTD 01/29/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8043

REVISION NR 5 DTD 04/29/2009

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS5100

REVISION NR 39 DTD 10/27/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 78286 SS8013

REVISION NR 09 DTD 11/21/2013

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81996 70217-02723-041

REVISION NR DTD 10/06/2015

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: CUSTOMER DIRECT, CONUS

PKGING DATA-QUP:001

SHALL BE PACKAGED IN ACCORDANCE WITH ASTM D 3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

Markings Paragraph When ASTM D3951, Commercial Packaging is specified, the following apply:

•,,All Section “D” Packaging and Marking Clauses take precedence over

ASTM D3951.

•,,In addition to requirements in MIL-STD-129, when Commercial Packaging is used, the Method of Preservation for all MIL-STD-129 marking and labeling shall be “CP” Commercial Pack.

•,,The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) as specified in the contract take precedence over QUP in ASTM D3951.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND

NON-MANUFACTURERS)

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR

SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER A0003

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

REFERENCE NUMBER ZD042

Contractor first article/preproduction approval testing required. Use DI-NDTI-80809B in preparation of the first article report. Current revision of MIL-HDBK-831 may also be used for report format guidance.

First article testing shall be conducted IAW applicable drawings and drawing notes, specification, engineering instructions and specific requirements set forth in the contract. Additionally, 100% dimensional characteristics check shall be performed and results provided to the contracting officer. The first article offered must be manufactured at the facilities in which production quantities are procured under the contract. Contractor shall provide a statement along with objective evidence that test and production items meet the material and process requirements of the contract. If applicable, DD form 1423 documentation shall be provided as required. Unless F.A.T sample(s) is degraded or destroyed in testing or submitted for government fit, form, function verification (when specified by contract), the F.A.T. samples(s) may be deliverable with the last production run of the contract.

Additional Wide Area Workkflow (WAWF) instructions for contractor first article test CLIN: The contractor shall code the receiving report for contractor first article test CLIN in WAWF as follows: Inspection at origin (source)- Enter the DCMA DODAAC listed on page 1 of the contract.

Acceptance at destination- Enter the issue by office DODAAC listed Ship to code- Enter the issue by office DODAAC listed on page 1 of the contract.

REFERENCE NUMBER A1166

RESTRICTION ON THE ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011)

An award can only be made for a bearing manufactured in the United States, its outlying areas, or Canada and the cost of the bearing components (bearing element, retainer, inner race, outer race) manufactured in the United States, its outlying areas, or Canada must exceed 50% of the total cost of the bearing components of that ball or roller bearing. See DFARS Clause 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER BEARINGS (Jun 2011). A Contractor's declaration on the domestic/foreign nature of the material being offered is required. To obtain a copy of the "Contractors Declaration Form" please visit the DLA Aviation Foreign Bearing Website at http://www.dla.

mil/Aviation/Business/IndustryResources/DLAResourcesforSuppliers/ ForeignBearingWaiver.aspx Please have the completed form ready for submission upon request by the Acquisition Specialist. Failure to provide this information may result in your quote not being considered for award. In the event no offered bearings meet this sourcing requirement, this solicitation may be cancelled and a waiver may be requested by the procurement activity. Upon receipt of an approved waiver, the requirement may be resolicited. See FAR 225.7009-4, Waiver, Restriction on Ball and Roller Bearings (DEC 2010).

REFERENCE NUMBER CS001

THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO

EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND

ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH

JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF

STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL

AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, MILITARY CRITICAL

TECHNICAL DATA AGREEMENT, FORM IS AVAILABLE AT THE WORLD WIDE WEB

ADDRESS:

https://public.logisticsinformationservice.dla.mil/PublicHome/jcp/defaul t.aspx

OR BY WRITING TO:

DLA LOGISTICS INFORMATION SERVICE

FEDERAL CENTER

74 WASHINGTON AVE., NORTH

BATTLE CREEK, MI 49037-3084

TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A

CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,

DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY

THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN

EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 EXEMPTIONS OF

GENERAL APPLICABILITY, AND/OR EAR PART 740 ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE

REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT

OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE

EXPORT CONTROLLED TECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO

THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA

UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY

PERMITTED BY DODD 5230.25.

REFERENCE NUMBER ZD074

THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM - (TO INCLUDE 'COMMERCIAL

OF A TYPE')

REFERENCE NUMBER A1054

PRESERVATION, PACKAGING, PACKING, AND MARKING

REQUIREMENTS SHALL BE IN ACCORDANCE WITH

MIL-DTL-197M.

1. METHOD OF PRESERVATION SHALL BE DETERMINED BY

BEARING TYPE AND SIZE (REFER TO TABLE I).

2. PARAGRAPH 3.10.2, SELECTION OF UNIT

PRESERVATION, APPLIES. PROTECTIVE LUBRICANT OR

PRESERVATIVE COMPOUND SHALL BE DETERMINED

DEPENDENT UPON BEARING TYPE AND CLOSURE IN

ACCORDANCE WITH PARAGRAPH 3.3.4 AND TABLE II.

FOR PRESERVATION PROCESS CONTROLS, DEPENDANT

UPON BEARING TYPE, CLOSURE, AND LUBRICANT<(>,<)>

PARAGRAPHS 3.4 THROUGH 3.9 APPLY.

3. PACKAGING PRECAUTIONARY MARKING REQUIREMENTS

OF PARAGRAPH 3.12.4 APPLY.

4. CONTRACTOR'S PACKAGING FACILITY SHALL ADHERE

TO THE QUALITY ASSURANCE VERIFICATION

REQUIREMENTS AS CONTAINED WITHIN SECTION 4 OF

MIL-DTL-197L.

...END OF SPECIAL PACKAGING INSTRUCTIONS...