SPE1C127Q0182.pdf
PDF 165 KB Posted
- Attached to
- GLOVES, TOXICOLOGICA AND 2 MORE ITEMS
- Solicitation number
- SPE1C127Q0182
About this file
This is a Request for Quotations (RFQ) for toxicological protective gloves issued by DLA Troop Support on November 13, 2026, with quotations due by November 30, 2026. The solicitation (SPE1C1-27-Q-0182) seeks 1,000 pairs each of three different glove models (NSNs 8415-00-753-6550, 8415-00-753-6554, and 8415-00-753-6551), all classified as Type II M2 and M3 without closure rings. The delivery requirement is 163 days after order date, with firm fixed pricing on a FOB Destination basis at the origin inspection and acceptance point. Unit prices must include all costs associated with First Article Testing (FAT) requirements, which involve 117 pairs of samples for visual, dimensional, porosity, physical, and chemical testing over a 90-day period.
The gloves are classified as Type II shelf-life items with a 36-month initial shelf-life, extendable once for four additional years to a total of 84 months. Packaging must comply with Level C/C preservation standards per ASTM-D3951, with individual pairs unit-packed in 0.015-inch nominal thickness polyethylene bags and marked per MIL-STD-129. Production lot testing sample sizes vary based on lot size, with conformance inspection not to exceed 35 calendar days. Critical identification marking requirements include contract number and PIID on unit, intermediate, exterior container, and palletized unit load labels. Surveillance requirements include initial inspection at 36 months followed by visual inspections at 48, 60, and 72 months. FAT samples for visual and dimensional testing ship to DLA Troop Support Philadelphia (Attn: Ryan Hutton), while porosity, physical, and chemical samples ship to JEFS Test Management Services in London, Ohio. The solicitation incorporates DLA Master Solicitation for eProcurement Automated Simplified Acquisitions (PART 13) Revision 105 and requires cybersecurity maturity model certification (CMMC) Level 2 self-assessment and covered defense information handling.
View the file
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
REQUEST FOR QUOTATIONS THIS RFQ IS IS NOT A SMALL BUSINESS SET-ASIDE
4. CERT.FOR NAT. DEF.
UNDER BDSA REG. 2
AND/OR DMS REG. 1
5. ISSUED BY
7. DELIVERY
9. DESTINATION
10. PLEASE FURNISH QUOTATIONS TO THE
ISSUING OFFICE IN BLOCK 5 ON OR
BEFORE CLOSE OF BUSINESS (Date)
IMPORTANT: This is a request for information, and quotations furnished are not offers. If you are unable to quote, please so indicate on this form and return it to the address in Block 5. This request does not commit the Government to pay any costs incurred in the preparation of the submission of this quotation or to contract for supplies or services. Supplies are of domestic origin unless otherwise indicated by quoter. Any representations and/or certifications attached to this Request for Quotations must be completed by the quoter.
11. SCHEDULE (See Continuation Sheets)
12. DISCOUNT FOR PROMPT PAYMENT
d. CALENDAR DAYS
NUMBER PERCENTAGE
NOTE: Additional provisions and representations are are not attached.
13. NAME AND ADDRESS OF QUOTER
a. NAME OF QUOTER
14. SIGNATURE OF PERSON AUTHORIZED TO SIGN
QUOTATION
16. SIGNER
AUTHORIZED FOR LOCAL REPRODUCTION
Previous edition not useable
STANDARD FORM 18 (REV. 6-95)
Prescribed by GSA-FAR (48 CFR) 53.215-1(a)
SPE1C1-27-Q-0182
1. REQUEST NO.
2026 NOV 13
2. DATE ISSUED
7018088832
3. REQUISITION/PURCHASE REQUEST NO.
DO-C9
RATING
DLA TROOP SUPPORT
C AND T SUPPLY CHAIN
700 ROBBINS AVENUE
PHILADELPHIA PA 19111-5096
USA
Buyer: Ryan Hutton DRH0143 Tel: 4457378134 Email: Ryan.Hutton@dla.mil
163 DAYS ADO
6. DELIVER BY (Date)
8. TO:
c. CITY
d. STATE
b. STREET ADDRESS
a. NAME OF CONSIGNEE
e. ZIP CODE
a. 10 CALENDAR DAYS
b. 20 CALENDAR DAYS (%) c. 30 CALENDAR DAYS
15. DATE OF QUOTATION
a. NAME (Type or Print)
AREA CODE
c. TITLE (Type or Print)d. CITY
c. COUNTY
b. STREET ADDRESS
e. STATE f. ZIP CODE
See Schedule
2026 NOV 30
NUMBER
FOB DESTINATION
OTHER
(See Schedule)
CAGE
b. TELEPHONE
See attached schedule to complete quote information.
Quoter must also complete the following:
a. Quotation is valid for 90 days from date specified in Block 10 above unless otherwise indicated: _____________ .
b. Prices quoted are:
___ Contained in Commercial Catalog or Published Price List No. ___________________ dated _______________ page __________ .
___ Contained in Internal Price List No. _______________dated ____________________, which may be examined at our facility.
___ Commercial sales of comparable quantities: Quantity ____________ ; Price _____________;
___ Customer ________________________.
___ Other (provide basis) ______________________________________ _______________________________________ .
c. FOB Point: ____ Destination ____ Origin Shipping Point (City, State) _________________________________________ .
d. If delivery period shown in Block 6 is unacceptable, provide best possible delivery: _________________________________.
e. Remittance Address (Name, Street, City, State, ZIP): Same as Block 13 unless otherwise indicated below:
f. Vendor FAX Number: ____________________ Vendor Toll-Free Number: ____________________ Vendor E-mail: ______________________________
CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED:
CONTINUED ON NEXT PAGE
PAGE 2 OF 37 PAGES
SPE1C1-27-Q-0182
THIS SOLICITATION INCORPORATES THE TERMS AND CONDITIONS SET FORTH IN THE DLA MASTER SOLICITATION FOR EPROCUREMENT AUTOMATED SIMPLIFIED ACQUISITIONS (PART13) REVISION 105 (May 20, 2026) WHICH CAN BE FOUND ON THE WEB AT: https://www.
dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
NOTES:
1. THIS SOLICITATION INCLUDES FIRST ARTICLE TESTING REQUIREMENTS.
2. UNIT PRICES ARE TO BE BASED ON FOB DESTINATION AND INCLUDE FIRST ARTICLE TESTING REQUIREMENTS. (SEE E08)
3. THE PRODUCTION LEAD TIME (PLT) IS 163 DAYS AFTER THE DATE OF THE ORDER. HOWEVER, THERE IS A FIRST ARTICLE TESTING REQUIREMENT. THEREFORE, AN ADDITIONAL 90 DAYS WILL BE ADDED TO THE FIRST SCHEDULED SHIPMENT OF THE FIRST DELIVERY ORDER OF THE AWARD CONTRACT. THIS ADDITIONAL TIME IS TO ALLOW THE SUCCESSFUL AWARDEE TIME TO MANUFACTURE, SHIP, AND FOR DLA TROOP SUPPORT TO RECEIVE THE FAT SAMPLE AND FOR THE GOVERNMENT TO REVIEW THE SAMPLES.
First Article Testing (FAT) Testing Sample Size: 117 pairs total Visual/dimensional = 40 pairs {8 pair of each size (5 sizes)} Porosity = 40 pairs {8 pair of each size (5 sizes)} Physical = 27 pairs (Note: this sampling includes the Bond Sulfur tests) Chemical = 10 pairs (5 pairs large 5 pairs X-Large)
FAT will take 90 days to be performed. FAT samples for Visual, and Dimensional Requirements, along with a DD1222 form, shall be sent to the below address. A copy of that DD1222 shall be sent to the Government email, troopsupportchemteam@dla.mil: (Please include Manufacture/Cure Date in Remarks Block of the DD1222).
DLA Troop Support Philadelphia Attn: Ryan Hutton Bldg. 3C 700 Robbins Street Philadelphia, PA 19111
FAT samples for Porosity, Physical and Chemical Property Requirements, along with a DD1222 form, shall be sent to the below address. A copy of that DD1222 shall be sent to the Government email, troopsupportchemteam@dla.mil: (Please include Manufacture/Cure Date in Remarks Block of the DD1222).
JEFS Test Management Services ATTN: Cathy Campbell Joint Testing Operations Center 120 Maple Street London, OH 43140
Production Lot Testing
Production Lot Testing Sample size:
Maximum lot size:
40,000 gloves or 20,000 pairs of gloves
Physical Testing:
Lot size (pairs) Number of sample units 400 or less 36 gloves (18 pairs) 401 up to and including 11,000 54 gloves (27 pairs) 11,001 and over 90 gloves (45 pairs) Porosity Testing:
Lot size (pairs) Number of sample units 4 or less 1 pair of gloves 5 to 8 2 pairs of gloves 9 to 13 3 pairs of gloves 14 to 25 4 pairs of gloves 26 to 45 7 pairs of gloves 46 to 75 10 pairs of gloves 76 to 140 16 pairs of gloves 141 to 250 25 pairs of gloves 251 to 600 40 pairs of gloves 601 to 1,600 63 pairs of gloves 1,601 to 5,000 100 pairs of gloves 5,000 and over 158 pairs of gloves
Chemical Testing:
Lot size (pairs) Number of sample units 13 or less 8 gloves (4 pairs) 14 to 75 12 gloves (6 pairs) 76 to 600 20 gloves (10 pairs) 601 to 17,500 32 gloves (16 pairs)
Conformance Inspection Samples (Production Lot Testing, PLT):
Conformance inspection shall not exceed 35 calendar days, from date test items are received at the test facility to the notification letter of test results. The samples along with a DD1222 form shall be sent to the below address, and
PAGE 3 OF 37 PAGES
SPE1C1-27-Q-0182
a copy of that DD1222 shall be sent to the below address, and a copy of that DD1222 shall be sent to the Government email, troopsupportchemteam@dla.mil: (Please include Manufacture/Cure Date in the Remarks Block of the DD1222).
JEFS Test Management Services Attn: Cathy Campbell 120 Maple St London, OH 43140 740-852-5256
Conformance acceptance and rejection:
Testing results, along with the receipted DD1222 shall be provided to the Government at troopsupportchemteam@dla.mil.
The Government will provide the contractor with all passing or failing test results. A detailed rejection letter will accompany failing test reports. Once the Contractor receives PASSING test results and the QAR releases the lot with their signature on Wide Area Work Flow (WAWF), the Contractor can then ship the lot. If FAILING results are received on PLT, a retest of that lot shall be done. The Contractor will be notified that a retest will be taking place;
additional time will be required based on the lab's root cause analysis of the failure. If additional samples are needed for a retest, the Contractor will be notified. If PASSING results are received, the same steps as above will follow, if retest fails, a rejection letter of that lot shall be provided to the Contractor. That lot is to be segregated from all other production lots to prevent intermingling with conforming product. The Contractor will conduct and provide a root cause analysis and provide Corrective Action Report (CAR) to the Government.
Shelf-Life This is a Type II Shelf-life item With a Shelf-life of 36 months (3 years) Extendable once (1) for four (4) years For a total of 84 months (7 years) First Lab Inspection at: 36 months Re inspection (visual): Every 12 months at 48, 60, and 72 months.
Re Inspection Limit: 4
Surveillance:
Shelf-Life Month: 084 Months (7 years) Shelf-Life Type: II First Inspection Month: 036 Re Inspection Month: 012 Re Inspection Limit: 4 The first inspection at 36 month consists of Chemical Agent and Physical Property Testing by JEFS. This initial inspection extends the shelf-life of the items to their whole life of 7 years. The initial inspection at 36 month is followed three annual visual inspections by DLA. Re-inspection limit of four (4) indicates that there will be a total of four inspections - at 36 month, 48 month, 60 month, and 72 month.
Address to ship the surveillance set-aside samples:
DoDDACC: HQ0493 Joint Test Operations Center (JTOC) Cathy Campbell 120 Maple ST.
London, Ohio 43140
PAGE 4 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLIES/SERVICES: PGC: 00565
ITEM DESCRIPTION:
GLOVES, TOXICOLOGICAL AGENTS PROTECTIVE
GLOVES, TAP M3 TYPE II
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RD004: CybersecurityMaturity Model Certification (CMMC) Level 2 Self-Assessment
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENTINCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTERLIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FORSIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGEACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES AFOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST(SAR)
RD002, COVERED DEFENSE INFORMATION APPLIES
TYPE II (M2 AND M3, WITHOUT CLOSURE RING)
INSPECTION OF SUPPLIES SHALL BE INACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.
ADDITIONAL INFORMATION FOR MIL-STD-105E:
MIL-STD-105E, dated 10 May 1989,is hereby canceled.
Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQZ1.4, "Sampling Procedures and Tables for Inspection by Attributes."
Users are cautioned to evaluate these documents for theirparticular application before citing it as a replacement document.
(Copies of MIL-STD-1916 are available online athttp://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia,PA 19111-5094.)
(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)
ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:
NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.
APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON AVENUE
MILWAUKEE,WISCONSIN 53203
(Ref. T0795 - May 17, 2006) RS060: Shelf life requirement RS001 for a TYPE 2 (CODE 7) item with a shelf life of 36 month (extendable) applies to this item.
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments%2FDLMS% 2FeApplications%2FLogDataAdmin%2FUnit_of_Issue_and_Purchase_Unit.xlsx&wdOrigin=BROWSELINK
ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT .
0001 8415-00-753-6550 1,000.000 PR $ ________________ $ ________________
GLOVES
,TOXICOLOGICA
PRICING TERMS: Firm Fixed Price
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
PAGE 5 OF 37 PAGES
SPE1C1-27-Q-0182
SUPPLY/SERVICE: PGC: 00565 CONT'D
ACCEPTANCE POINT: ORIGIN
FOB: DESTINATION DELIVERY DATE: 163 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA - MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNNTHKNESS:0
UNIT CONT:00 OPI:O
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No specialmarking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING
REQUIREMENTS FOR PROCUREMENT
PRES/PACK C/C TOASTM-D-3951
NOTE: THIS IS A TYPE II SHELF-LIFE ITEM
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/Cin accordance with ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packedin a flat plastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with the back side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formedwith heat sealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closureof the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated from thepolyethylene film tubing or sheeting. Prior to or during the closure operation, excess air within the bag shall be expelled.
AType VIII, Class 17 of MIL-DTL-32075 barcoded label shall be affixed to the outside of the individual bag.
Markings:
CRITICALIDENTIFICATION MARKING REQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items,the inclusion of the Contract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exteriorcontainer and palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19F-XXXX”. This identification marking information to include the contract number is a standardization process to identify materialfor Shelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory marking requirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the shipping container withthe same information and in the same locations described above.
The container markings shall include the following information:
Size:
NSN:
PAGE 6 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
MATERIALS ANY COMPONENTMISSING, DAMAGED OR NOTAS
SPECIFIED.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
PAGE 7 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
OR PURCHASE ORDER, UNIT PACKS,SHIPPING CONTAINERS AND PALLETIZED UNIT
LOADS SHALL BE MARKED IN ACCORDANCE WITH ASTM D 3951.
PARCEL POST ADDRESS:
UY0157
PECKHAM INC
OCIE NORTH 3PL
5408 W GRAND RIVER AVE BLDG B
LANSING MI 48906
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND
CONTRACT
FREIGHT SHIPPING ADDRESS:
UY0157
PECKHAM INC
OCIE 3PL
5408 W GRAND RIVER AVE BLDG B
GOVT USE
External External External Customer RDD/ ITEM PR PRLI PR PRLI Material Need Ship Date .
0001 7018088832 0001 N/A N/A N/A 07/21/2027
GLOVES, TAP M3 TYPE II
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RD004: CybersecurityMaturity Model Certification (CMMC) Level 2 Self-Assessment
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENTINCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET
PAGE 8 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
FORTH IN FULL TEXT IN THE DLA MASTERLIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FORSIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGEACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES AFOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST(SAR)
RD002, COVERED DEFENSE INFORMATION APPLIES
TYPE II (M2 AND M3, WITHOUT CLOSURE RING)
INSPECTION OF SUPPLIES SHALL BE INACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.
ADDITIONAL INFORMATION FOR MIL-STD-105E:
MIL-STD-105E, dated 10 May 1989,is hereby canceled.
Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQZ1.4, "Sampling Procedures and Tables for Inspection by Attributes."
Users are cautioned to evaluate these documents for theirparticular application before citing it as a replacement document.
(Copies of MIL-STD-1916 are available online athttp://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia,PA 19111-5094.)
(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)
ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:
NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.
APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON AVENUE
MILWAUKEE,WISCONSIN 53203
(Ref. T0795 - May 17, 2006) RS060: Shelf life requirement RS001 for a TYPE 2 (CODE 7) item with a shelf life of 36 month (extendable) applies to
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments%2FDLMS%
0002 8415-00-753-6554 1,000.000 PR $ ________________ $ ________________
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
FOB: DESTINATION DELIVERY DATE: 163 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA - MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNNTHKNESS:0
UNIT CONT:00 OPI:O
PAGE 9 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No specialmarking
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/Cin accordance with ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packedin a flat plastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with the back side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formedwith heat sealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closureof the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated
Markings:
CRITICALIDENTIFICATION MARKING REQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items,the inclusion of the Contract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exteriorcontainer and palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19F-XXXX”. This identification marking information to include the contract number is a standardization process to identify materialfor Shelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory marking requirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the shipping container withthe same information and in the same locations described above.
The container markings shall include the following information:
Size:
NSN:
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
PAGE 10 OF 37 PAGES
SPE1C1-27-Q-0182
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
PAGE 11 OF 37 PAGES
SPE1C1-27-Q-0182
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
OR PURCHASE ORDER, UNIT PACKS,SHIPPING CONTAINERS AND PALLETIZED UNIT
LOADS SHALL BE MARKED IN ACCORDANCE WITH ASTM D 3951.
PKGING DATA - MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:00 OPI:O
PACK CODE:U
MARKINGSHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PRES/PACK C/C TO ASTM-D-3951
NOTE: THISIS A TYPE II SHELF-LIFE ITEM
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/C in accordancewith ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packed in a flatplastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with theback side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formed with heatsealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closure of the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated from the polyethylene filmtubing or sheeting. Prior to or during the
A Type VIII, Class 17of MIL-DTL-32075 barcoded label shall be affixed
Markings:
CRITICAL IDENTIFICATION MARKINGREQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items, the inclusion of theContract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exterior containerand palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19 F-XXXX”.This identification marking information to include the contract number is a standardization process to identify material forShelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory markingrequirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the shipping container withthe same information and in the same locations described above.
PAGE 12 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
The container markings shall include the following information:
Size:
NSN:
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
PAGE 13 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
PECKHAM INC
OCIE NORTH 3PL
5408 W GRAND RIVER AVE BLDG B
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND
FREIGHT SHIPPING ADDRESS:
UY0157
PECKHAM INC
OCIE 3PL
5408 W GRAND RIVER AVE BLDG B
ITEM PR PRLI PR PRLI Material Need Ship Date .
0002 7018088832 0002 N/A N/A 7536554 07/21/2027
GLOVES, TAP M3 TYPE II
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RD004: CybersecurityMaturity Model Certification (CMMC) Level 2 Self-Assessment
PAGE 14 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENTINCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTERLIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FORSIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGEACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES AFOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST(SAR)
RD002, COVERED DEFENSE INFORMATION APPLIES
TYPE II (M2 AND M3, WITHOUT CLOSURE RING)
INSPECTION OF SUPPLIES SHALL BE INACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.
ADDITIONAL INFORMATION FOR MIL-STD-105E:
MIL-STD-105E, dated 10 May 1989,is hereby canceled.
Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQZ1.4, "Sampling Procedures and Tables for Inspection by Attributes."
Users are cautioned to evaluate these documents for theirparticular application before citing it as a replacement document.
(Copies of MIL-STD-1916 are available online athttp://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia,PA 19111-5094.)
(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)
ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:
NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.
APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON AVENUE
MILWAUKEE,WISCONSIN 53203
(Ref. T0795 - May 17, 2006) RS060: Shelf life requirement RS001 for a TYPE 2 (CODE 7) item with a shelf life of 36 month (extendable) applies to
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments%2FDLMS%
0003 8415-00-753-6551 1,000.000 PR $ ________________ $ ________________
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
FOB: DESTINATION DELIVERY DATE: 163 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA - MIL-STD-2073-1E
PAGE 15 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNNTHKNESS:0
UNIT CONT:00 OPI:O
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No specialmarking
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/Cin accordance with ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packedin a flat plastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with the back side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formedwith heat sealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closureof the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated
Markings:
CRITICALIDENTIFICATION MARKING REQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items,the inclusion of the Contract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exteriorcontainer and palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19F-XXXX”. This identification marking information to include the contract number is a standardization process to identify materialfor Shelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory marking requirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the shipping container withthe same information and in the same locations described above.
The container markings shall include the following information:
Size:
NSN:
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot
PAGE 16 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
PAGE 17 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
OR PURCHASE ORDER, UNIT PACKS,SHIPPING CONTAINERS AND PALLETIZED UNIT
LOADS SHALL BE MARKED IN ACCORDANCE WITH ASTM D 3951.
PKGING DATA - MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:00 OPI:O
PACK CODE:U
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/C in accordancewith ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packed in a flatplastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with theback side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formed with heatsealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closure of the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated
Markings:
CRITICAL IDENTIFICATION MARKINGREQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items, the inclusion of theContract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exterior containerand palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19 F-XXXX”.This identification marking information to include the contract number is a standardization process to identify material forShelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory markingrequirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the
PAGE 18 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
shipping container withthe same information and in the same locations described above.
The container markings shall include the following information:
Size:
NSN:
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
PAGE 19 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
OR PURCHASE ORDER, UNIT PACKS,SHIPPING CONTAINERS AND PALLETIZED UNIT
LOADS SHALL BE MARKED IN ACCORDANCE WITH ASTM D 3951.
PKGING DATA - MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:00 OPI:O
PACK CODE:U
WITH A SHELF-LIFE OF 36 MONTHS.
Preservation and packaging shall be Level C/C in accordancewith ASTM-D3951. In addition, one pair of toxicological protective gloves with instruction sheet shall be unit packed in a flatplastic bag of
0.015 inch nominal thickness. Each pair of chemical protective gloves shall be positioned fingertip to cuff with theback side of each glove facing outward to permit the required markings to be read.
The polyethylene bag shall be formed with heatsealed seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The final closure of the bag shall be heat sealed with the seal made as close as possible to the open end. The bag may be fabricated
Markings:
CRITICAL IDENTIFICATION MARKINGREQUIREMENTS: As an exception to the MIL-STD -129R (May 24, 2018) Change Letter 1, for Shelf-life items, the inclusion of theContract number [in addition to the PIID (13-digit number)] shall be applied to unit, intermediate, exterior containerand palletized unit load identification labels. Example: “Contract #:
SPE1C1-18-D-XXXX” and underneath “PIID: SPE1C1-19 F-XXXX”.This identification marking information to include the contract number is a standardization process to identify material forShelf-life testing. The contract number is necessary for Shelf-life documentation. Failure to comply with this mandatory markingrequirement will result in a Supply Discrepancy Report and either require the supplier’s financial reimbursement for remarking orpossible rejection of delivered supplies.
NOTE: Contract number only is required information for COSIS and for DD FORM 2477-1(Extended Shelf-life) as well as other Shelf-life
PAGE 20 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
tracking systems
Shelf-Life items will be marked for identification and controlas stated in DoD 4140.27M Shelf-life Management Manual (see 2-13). Markings, shown below the item identification data and requiredon all unit, intermediate, and exterior packs, shall be per MIL STD 129, MIL STD 290 (FSC 9150 only), or FED STD 123, (references(m) through (p)) respectively.
Shipping containers shall be marked in accordance with MIL-STD-129.
The markings shall be stenciled, stamped, or printed on one side and one end of the container in black characters no less than 1/2 inch in height; surveillancemarkings which shall be in 1 3/8 inch high characters. As alternates, adhesive labels may be applied to the shipping container withthe same information and in the same locations described above.
The container markings shall include the following information:
Size:
NSN:
Cage:
P/N:
Quantity/Unit of Issue:
Contract Number:
DO (PIID)number:
Military method and date of preservation: (M10-mm/yy) Surveillance Lot:
MFD: mm/yy (Date the firstbutyl glove in the production lot was produced) Expiration Date: mm/yy (15 years after manufacturing date) Grossweight: (indicated in whole pounds)
The last container loaded for each shipment shall have the packing list included, and state“PACKING LIST HERE.
DOD BAR CODE MARKING REQUIRED IN
ACCORDANCE WITH MIL-STD-129.
THE FULLY PACKAGED END ITEMS SHALL BE EXAMINEDFOR
THE DEFECTS LISTED BELOW. THE LOT SIZE SHALL BE EXPRESSED
IN UNITS OF SHIPPING CONTAINERS. THE SAMPLE UNIT
SHALL BE S-2 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS
PER HUNDRED UNITS SHALL BE2.5.
EXAMINEDEFECTS
MARKING (EXTERIOR & UNIT PACKS) OMITTED, INCORRECT,
ILLLEGIBLE, OF IMPROPER
SIZE, LOCATION, SEQUENCE
OR METHOD OF APPLICATION.
EXAMINEDEFECTS
WORKMANSHIP INADEQUATE APPLICATION OF COMPONENTS SUCH AS:
INCOMPLETE SEALING
CLOSURE OF CONTAINER FLAP, LOOSE STRAPPING,
IMPROPER TAPING
OR INADEQUATE STAPLING.
OPEN AND NONCONTINUOUS HEAT SEALED SEAMS AND
CLOSURE OF POLYETHYLENE
BAG. INCORRECTLY FABRICATEDBAG. BULGED OR
PAGE 21 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION B
SUPPLY/SERVICE: PGC: 00565 CONT'D
DISTORTED CONTAINER.
GLOVES NOT POSITIONED CUFF TO FINGERTIP, WITH
BACK OF EACH GLOVE CUFF
NOT FACING OUTWARD.
CONTENT NUMBER OF PAIRS OF GLOVES PER CONTAINER IS MORE
OR LESS THANREQUIRED.
PALLETIZATION EXAMINATION.
THE FULLY PACKAGED AND PALLETIZED END ITEMS SHALL BE EXAMINED FOR THE
DEFECTS LISTED BELOW.THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF
PALLETIZED UNIT LOADS. THE SAMPLE UNIT SHALL BE ONE PALLETIZED UNIT
LOAD FULLYPACKAGED. THE INSPECTION LEVEL SHALL BE S-1 AND THE AQL,
EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE6.5.
EXAMINEDEFECTS
FINISHED DIMENSIONS LENGTH, WIDTH OR HEIGHT EXCEEDS SPECIFIED
MAXIMUMREQUIREMENTS.
PALLETIZATION PALLET PATTERN NOT AS SPECIFIED. LOAD NOT
BONDED AS SPECIFIED.
WEIGHTEXCEEDS MAXIMUM LOAD LIMITS.
MARKING OMITTED; INCORRECT; ILLEGIBLE; OF IMPROPER SIZE,
LCATION, SEQUENCE OR METHODOF APPLICATION.
PALLETIZATION.
BOXES OF GLOVES, PACKED AS SPECIFIED, SHALL BE PALLETIZED ON A 4-WAY
ENTRY, 40X48 INCH WING-TYPEPALLET AND THE LOAD BONDED.
MARKING.
IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY THE CONTRACT
PECKHAM INC
OCIE NORTH 3PL
5408 W GRAND RIVER AVE BLDG B
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND
FREIGHT SHIPPING ADDRESS:
UY0157
PECKHAM INC
OCIE 3PL
5408 W GRAND RIVER AVE BLDG B
PAGE 22 OF 37 PAGES
SPE1C1-27-Q-0182
ITEM PR PRLI PR PRLI Material Need Ship Date .
0003 7018088832 0003 N/A N/A N/A 07/21/2027
CONTINUATION SHEET REFERENCE NO. OF DOCUMENT BEING CONTINUED: PAGE 23 OF 37 PAGES
SPE1C1-27-Q-0182
SECTION C - SPECIFICATIONS/SOW/SOO/ORD
C03…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .