Interim Tech Changes MC AWC Women April 7 2022.docx

INTERIM CHANGES| CR PD 03-09 MC WOMENS AWC 4/6/2022

COAT, ALL WEATHER, WOMAN'S, PEWTER

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

NEW DESIGN

ADDITIONAL INFORMATION FOR PD 03-09:

PGC:02851

PATTERN DATE: 27 JANUARY 2016

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER

AND COTTON (WATER REPELLENT), MARINE CORPS PEWTER

2246 CONFORMING TO A-A-50531A IS AVAILABLE FOR

SHADE, FINISH & COLORFASTNESS ON ROLL NO. 3897

THIS SAMPLE SHALL SHOW COLORFASTNESS IN

ACCORDANCE WITH THE TABLE BELOW.

CHARACTERISTICS REQUIREMENT TEST METHOD

LAUNDERING (MIN) EQUAL TO STANDARD AATCC 61 3A

AFTER 3 CYCLES GRADE 4 AATCC 61 3A

CROCKING (MIN) GRADE 2.5 AATCC 8

LIGHT (MIN) GRADE 4 AATCC 16 OPT A

INTERIM CHANGES TO PD-03-08

PAGE 1, PARA. 2, IN *SCHEDULE OF SIZES): ADD

SIZE 12 AND 14 FOR *EXTRA LONG)

. PAGE 11, PARA.3.7. FINISHED MEASUREMENTS, TABLE 1V

UNDER *BACK LENGTH TYPE II) FOR SIZE 12XL ADD *48

AND FOR SIZE 14XL ADD *48 1/4"

PAGE 12, PARA. 3.7.1, LINER MEASUREMENTS, TABLE V

UNDER *BACK LENGTH, TYPE II FOR SIZE 12XL ADD

*37-3/4) AND FOR SIZE 14XL ADD *38)

INTERIM CHANGES TO CR/PD 03-09

PAGE 1, SCHEDULE OF SIZES, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"SHORT REG LONG XLONG

XO XO XO ---

2 2 2 --- 4 4 4 --- 6 6 6 --- 8 8 8 --- 10 10 10 --- 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 --- 22 22 22 --- 24 --- --- --- 26 --- ---

PAGE 2, PARAGRAPH 3.1 DESCRIPTION. LINE 5

AFTER "5" ADD "THE MATERIAL FOR THE SLEEVE

LINING SHALL BE TAFFETA AS SPECIFIED

IN PARAGRAPH 3.3.2.2.)

LINE 5, DELETE "1/4" AND SUBSTITUTE "3/8".

PAGE 2, PARAGRAPH 3.1.1, BELT AND BUCKLE.

LINE 2. DELETE "RIGHT SIDE" AND SUBSTITUTE

"LEFT SIDE".

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT.

LINE 5. DELETE THE LINE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING: "THE BELT LOOP ON THE

LEFT SIDE SEAM SHALL HAVE AN UNDER LOOP FOR THE

BELT ANCHOR."

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT.

LINE 1, AFTER "FINISHING" DELETE "1/2" AND

SUBSTITUTE "2-1/2".

PAGE 2, PARA. 3.1.2A SHOULDER STRAPS. DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH: "3.1.2A SHOULDER STRAPS.

THE OVEREDGED STRAIGHT END OF SHOULDER STRAP

SHALL BE SEWN TO THE COAT WITH A 3/16 INCH SEAM

THEN FOLD STRAP TO THE FINISHED POSITION AND TOP

STITCH 1/4 INCH FROM THE FOLDED EDGE. THE

FINISHED SHOULDER STRAPS SHALL BE CENTERED ALONG

THE SHOULDER SEAM AND THE POINTED END SHALL

FINISH EVEN TO 1/2 INCH FROM THE COLLAR SETTING

SEAM. THE SHOULDER STRAPS SHALL FINISH SMOOTH

AND FLAT WITHOUT DISTORTION. THE SHOULDER STRAP

TOPSTITCHING SHALL FOLLOW THE TOP STITCHING LINE

OF THE FRONT SLEEVE SEAMS."

PAGE 2, PARAGRAPH 3.1.5, REMOVABLE LINER.

LINE 1, DELETE "SET IN SLEEVES" AND

SUBSTITUTE "1/2 RAGLAND SLEEVES".

LINE 3, AFTER ACCOMMODATE A" DELETE "27"

AND SUBSTITUTE "24".

PAGE 3, PARAGRAPH 3.1.5.1 DELETE ENTIRELY

PAGE 3, PARAGRAPH 3.2.2. BUTTONHOLES. LINE 4,

AFTER "ONE ON THE LEFT FRONT" INSERT "IN

HORIZONTAL ALIGNMENT WITH TOP BUTTON ON RIGHT

FRONT" AND AFTER "ONE ON EACH LAPEL" INSERT

"AND THE CUT OPENING OF BUTTONHOLES SHALL BE

POSITIONED 3/4 INCH FROM EDGE OF COAT."

PAGE 3, PARAGRAPH 3.2.2, BUTTONHOLES. LINE 5

AFTER "SQUARE-BAR TYPE" ADD "WORKED OVER

GIMP". AT END OF THE PARAGRAPH ADD:

"THERE SHALL BE TWO 3/4 INCH CUT, SQUARE BAR

TYPE BUTTONHOLES, ONE CENTERED ON THE BELT

FASTENER 3/8 INCH FROM THE END AND ONE

CENTERED ON THE RIGHT BACK VENT 3/4 INCH

FROM THE EDGE".

PAGE 3, PARAGRAPH 3.2.3 BUTTONS

LINE 2, DELETE "18" AND SUBSTITUTE "45"

PAGE 3, PARAGRAPH 3 AFTER "THE COAT SHALL HAVE

THREE 24 LIGNE BUTTONS" DELETE "ONE BUTTON SHALL

BE SEWN ON EACH SLEEVE LINING TO CORRESPOND WITH

THE LOOPS ON THE REMOVABLE LINER'S SLEEVE BOTTOM

AND ONE SHALL BE POSITIONED ON THE BELT FASTENER"

AND INSERT "ONE BUTTON SHALL BE SEWN ON EACH SLEEVE

LINING TO CORRESPOND WITH THE LOOPS ON THE REMOVABLE

LINER'S SLEEVE BOTTOM AND ONE ON THE LEFT BACK VENT TO

CORRESPOND TO THE BUTTONHOLE. THE COAT SHALL HAVE SEVEN

18 LIGNE BUTTONS; SIX ATTACHED TO THE 45 LIGNE

BUTTONS ON THE COAT FRONT AND ONE POSITIONED ON THE BELT."

PAGE 3, AFTER PARAGRAPH 3.2.3 BUTTONS, INSERT

NEW PARAGRAPH AS FOLLOWS:"3.2.3.1 LAPEL BUTTON

PLACEMENT. THE TOP RIGHT LAPEL BUTTON SHALL

BE POSITIONED SO THAT THE LEFT COAT FRONT LAYS

SMOOTH AND FLAT WITHOUT DISTORTION AND THE

NECK OPENING SHALL BE 2 TO 2-1/2 INCHES BETWEEN

COLLARSTAND JOINING SEAM AND COLLARSTAND JOINING

SEAM ACROSS FRONT OF COAT."

PAGE 6, PARAGRAPH 3.3.2.4, LINE 2, AFTER

"COMBED COTTON" INSERT "OR STAPLE RAYON".

LINE 9, DELETE "2.5" AND SUBSTITUTE "1.5".

PAGE 6, PARAGRAPH 3.3.3, LINE 1, DELETE "1/4"

AND SUBSTITUTE "3/8".

PAGE 8 TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING NEW TABLE:

1/ Size Diameter Lignes

Lignes, Min.

Total Quantity per coat

PAGE 8, PARAGRAPH 3.4.9 DELETE ENTIRELY AND

SUBSTITUTE: "3.4.10 SLIDE FASTENER. THE

SLIDE FASTENER FOR THE COAT AND THE REMOVABLE

LINER SHALL BE A SEPARATING, NON-REVERSIBLE,

RIGHT-HAND, LIGHT SIZE WITH AN ALUMINUM

OR BRASS CHAIN, SHORT TAB PULL. THE LENGTHS OF

THE SLIDE FASTENERS SHALL CONFORM TO THE SIZE

COAT WITH A MINIMUM LENGTH OF 70 INCHES. THE

COLOR OF THE TAPE SHALL BE A GOOD MATCH TO THE

BASIC MATERIAL AND SHALL BE 7/16 OR 9/16 INCH

WIDE. THE ENDS OF THE SLIDE FASTENER SHALL

BE EQUIDISTANT FROM THE BOTTOM EDGE OF THE COAT.

PAGE 10, PARA.3.5 LABELS, ADD NEW PARAGRAPH

"3.5.4 DLA TROOP SUPPORT EXCLUSIVE LABEL. EACH COAT

SHALL HAVE THE DLA TROOP SUPPORT EXCLUSIVE LABEL SEWN

TO THE LEFT INSIDE FRONT FACING ABOVE THE

SIZE/INSTRUCTION LABELS. THE LABEL SHALL BE

APPROXIMATELY 2 INCHES WIDE AND BE SEWN

ON ALL FOUR SIDES."

PAGE 10, TABLE III, LIST OF PATTERN PARTS, DELETE

IN ITS ENTIRETY AND REPLACE WITH THE FOLLOWING:

TYPE I PATTERN LIST:

MATERIAL PATTERN PART PATTERN NOMENCLATURE CUT PARTS

BASIC BACK 0309MC-BACK 2

MATERIAL FRONT 0309MC-FRONT 2

BACK SLEEVE 0309MC-BACK SLEEVE 2

FRONT SLEEVE 0309MC-FRONT SLEEVE 2

FRONT FACING 0309MC-FRONT FACING 2

COLLAR 0309MC-COLLAR 2

COLLAR STAND 0309MC-COLLAR STAND 2

BACK YOKE 0309MC-BACK YOKE 1

GUN FLAP LEFT

AND RIGHT 0309MC-GUN FLAP L-R 4

NECK FACING 0309MC-NECK FACING 1

BACK LINER 0309MC-BACK LINER 1

FRONT LINER 0309MC-FRONT LINER 2

BACK SLEEVECAP 0309MC- BCK SLV CAP 2

BELT 0309MC-BELT 1

SHOULDER STRAP 0309MC-SHOULDER STRP 4

SLEEVE STRAP 0309MC-SLEEVE STRAP 2

POCKET WELT 0309MC-POCKET WELT 2

UNDER POCKET 0309MC-UNDER POCKET 2

TOP HANGING

POCKET 0309MC-TOP HANG PCKT 2

LINING BACK SLEEVE 0309MC-BACK SLV TFFT 2

FRONT SLEEVE 0309MC-FRNT SLV TFFT 2

FUSIBLE BACK SLEEVE 0309MC-BACK SLV FUSB 2

INTERLINING FRONT SLEEVE 0309MC-FRNT SLV FUSB 2

COLLAR 0309MC-COLLAR FUSIBL 2

COLLAR STAND 0309MC-CLLR STND FUS 2

GUN FLAP LEFT

AND RIGHT 0309MC-GUN FLAP FUSB 2

NECK FACING 0309MC-NECK FAC FUSB 1

BELT 0309MC-BELT FUSIBL 1

SHOULDER STRAP 0309MC-SHLD STRP FUS 2

SLEEVE STRAP 0309MC-SLV STRP FUSB 2

POCKET WELT 0309MC-PCKT WELT FUS 2

LINER BACK QUILTED 0309MC-BACK LINR REM 1

REMOVEABLE FRONT QUILTED 0309MC-FRNT LINR REM 2

BACK SLEEVE 0309MC-BCK SLV LN RM 2

FRONT SLEEVE 0309MC-FRT SLV LN RM 2

MARKER BUTTON MARKER 0309MC-BUTTON MARKER 0

TYPE II PATTERN LIST:

MATERIAL PATTERN PART PATTERN NOMENCLATURE CUT PARTS

BASIC BACK 0309A-BACK 2

MATERIAL FRONT 0309A-FRONT 2

BACK SLEEVE 0309A-BACK SLEEVE 2

FRONT SLEEVE 0309A-FRONT SLEEVE 2

FRONT FACING 0309A-FRONT FACING 2

COLLAR 0309A-COLLAR 2

COLLAR STAND 0309A-COLLAR STAND 2

BACK YOKE 0309A-BACK YOKE 1

GUN FLAP LEFT 0309A-GUN FLAP LEFT 2

NECK FACING 0309A-NECK FACING 1

BACK LINER 0309A-BACK LINER 1

FRONT LINER 0309A-FRONT LINER 2

BACK SLEEVECAP 0309A-BACK SLV CAP 2

BELT 0309A-BELT 1

SHOULDER STRAP 0309A-SHOULDER STRAP 4

SLEEVE STRAP 0309A-SLEEVE STRAP 2

POCKET WELT 0309A -POCKET WELT 2

UNDER POCKET 0309A-UNDER POCKET 2

TOP HANGING

POCKET 0309A-TOP HANG PCKT 2

LINING BACK SLEEVE 0309A-BACK SLV TFFT 2

FRONT SLEEVE 0309A-FRONT SLV TFFT 2

FUSIBLE BACK SLEEVE 0309A-BACK SLV FUSBL 2

INTERLINING FRONT SLEEVE 0309A-FRONT SLV FUSB 2

COLLAR 0309A-COLLAR FUSIBLE 2

COLLAR STAND 0309A-CLLR STAND FUS 2

GUN FLAP LEFT 0309A-GN FLP LFT FUS 2

NECK FACING 0309A-NECK FAC FUS 1

BELT 0309A-BELT FUSIBLE 1

SHOULDER STRAP 0309A-SHLDR STRP FUS 2

SLEEVE STRAP 0309A-SLV STRAP FUSB 2

POCKET WELT 0309A-PCKT WELT FUSB 2

LINER BACK QUILTED 0309A-BACK LINER REM 1

REMOVEABLE FRONT QUILTED 0309A-FRONT LINR REM 2

BACK SLEEVE 0309A-BCK SLV LIN RM 2

FRONT SLEEVE 0309A-FRT SLV LIN RM 2

MARKER BUTTON MARKER 0309A-BUTTON MARKER 0

PAGE 11, TABLE 1V COAT FINISHED MEASURMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "16"

UNDER SIZE ADD "SIZES 20 22

BREAST (1/) TYPE I ONLY 55-1/2 57-1/2

BACK LENGTH TYPE I ONLY

. SHORT 43-3/4 44

. REGULAR 45-3/4 46

. LONG 47-3/4 48

BELT LENGTH TYPE I ONLY 57 59

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 55-1/2 57-1/2

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 45-1/2 45-3/4

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 17 17

. LONG -- --

. XLONG -- --

BELT LENGTH TYPE II ONLY 55 57

PAGE 12, TABLE V LINER FINISHED MEASURMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "15"

UNDER SIZE ADD "SIZES 20 22

BREAST (1/) TYPE I ONLY 49 51

BACK LENGTH TYPE I ONLY

. SHORT 34 34-1/4

. REGULAR 36 36-1/4

. LONG 38 38-1/4

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 47 49

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 35-3/4 36

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 16 16

. LONG -- --

. XLONG -- --"

PAGE 16, PARAGRAPH 7.2.2 ASTM TEST METHODS

ADD "D-256 STANDARD TEST METHOD FOR IMPACT

RESISTANCE OF PLASTICS AND ELECTRICAL INSULATING

MATERIALS".

PACKAGING AND MARKING INSRUCTIONS

TEN (10) ALL-WEATHER COATS, ONLY SIZE ONLY,

SHALL BE PACKED IN A SNUG-FITTING FIBERBOARD

SHIPPING CONTAINER CONFORMING TO ASTM-D5118,

TYPE CF, STYLE RSC, GRADE 275, VARIETY SW, CLASS

DOMESTIC WITH A DW LINER. THE DIMENSIONS OF THE

CONTAINER SHALL APPROXIIMATE 20-H X 16-W X 24-L.

METHOD OF CLOSURE SHALL BE IN ACCORDANCE WITH

ASTM-D-1974, 2A2, FIGURE 1 OR AS AN ALTERNATE

2B6 OR 3B7, FIGURE 3.

PAGE 17, FIGURE 1, REVERSE THE BELT DIRECTION TO

GO RIGHT TO LEFT, OPPOSITE OF THE FRONT CLOSURE.

PAGE 18, FIGURE 2, REVERSE THE BELT DIRECTION TO GO RIGHT TO LEFT, OPPOSITE OF THE FRONT CLOSURE.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4

GENERAL INSPECTION LEVEL 2".

(Ref. W2851)