SERVICE_RIBBON_Tech_Data.pdf

"SERVICE RIBBON, TYPE 1 "

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

"ACHIEVEMENT, SENIOR ROTC"

ACADEMIC R-1-1

FIVE (5) FIRST ARTICLE SAMPLES ARE REQUIRED. FIRST ARTICLE TESTING SHALL BE PERFORMED AND THE CONTRACTOR WILL BE NOTIFIED IN WRITING WITHIN THIRTY (30) CALENDAR DAYS AFTER

CONTRACTING OFFICER'S RECEIPT OF FIRST ARTICLE SAMPLES.

MIL-S-3951D NOT 2

MIL-DTL-11589/396 NOT 2

MIL-DTL-11589F SUP 1 NOT 2

ADDITIONAL INFORMATION FOR MIL-S-3951:

INTERIM CHANGE TO MIL-S-3951D:

PARA. 3.4.1 PRONG AND CLUTCH TYPE. CHANGE

THE THIRD SENTENCE AS FOLLOWS: "THE

PRONGS SHALL BE 7/16 INCH +/- 1/64 INCH

(0.79 CM +/- 0.04 CM LONG".

ADDITIONAL INFORMATION FOR NN-P-71:

NO ADDITIONAL INFORMATION FOLLOWS..

ADDITIONAL INFORMATION FOR PPP-B-636:

FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL

SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM- D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD

SHIPPING CONTAINERS.

ADDITIONAL INFORMATION FOR PPP-B-676:

NO ADDITIONAL INFORMATION FOLLOWS..

ADDITIONAL INFO FOR MIL-P-15011: NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR MIL-DTL-11589:

NO ADDITIONAL INFORMATION FOLLOWS.

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

ADDITIONAL INFORMATION FOR FED-STD-15:

FED-STD-151 IS HEREBY

CANCELLED AND REPLACED WITH ASTM-D-498

SEE FED-STD-151B(2) NOT 3

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD

INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION: INTERIM CHANGES TO A-A-50186:

PAGE 1:

PARA. 1.1 TYPES, NEXT TO TYPE V NON-WOVEN ADD

"(MEDIUM WEIGHT)", UNDER TYPE V ADD "TYPE VI

NON-WOVEN (LIGHT WEIGHT)".

PARAGRAPH 2.1, LINE 5. GENERAL.: DELETE

"SATURATION BONDED WITH ACRYLIC TYPE BINDER"

AND SUBSTITUTE "EITHER WET-LAID, SATURATION BONDED OR THERMAL BONDED".

PAGE 2:

TABLE 1. PHYSICAL REQUIREMENTS (WOVEN) UNDER TEST

METHOD COLUMN, LINE 3 DELETE "1600" AND SUBSTITUTE

"AATCC 20 3/".

TABLE I. PHYSICAL REQUIREMENTS (WOVEN) AT BOTTOM OF

PAGE UNDER FOOTNOTE 2/ ADD THE FOLLOWING: "3/ AMERICAN ASSOCIATION OF TEXTILE CHEMISTS

AND COLORISTS

TEST METHOD."

PAGE 3, TABLE II, PHYSICAL REQUIREMENTS (NONWOVEN) UNDER

TYPE V, AND VI, ACROSS "CONSTRUCTION": DELETE "WET-LAID"

http://assist.daps.dla.mil/ http://www.asq.org/

AND "WET-LAID OR SATURATE, THERMAL BONDED" AND SUBSTITUTE

"SEE 2.1" FOR BOTH TYPES.

TABLE II, UNDER TYPE VI: ADD UNDER EACH CHARACTERISTIC:

"1.5, 12, 8, 2.5, 2.5, WET-LAID OR SATURATE THERMAL BONDED" RESPECTIVELY.

PAGE 3, PARA. 3.2 FINISH. LINE 1 DELETE "AN APPROVED" AND SUBSTITUTE " A COMMERCIALLY

ACCEPTED".

PAGE 5: ADD THE FOLLOWING: "5.7 SUPER SESSION DATA.

THE TYPES OF CLOTH COVERED BY THIS COMMERCIAL ITEM

DESCRIPTION REPLACE TYPES COVERED BY CCC-C-438 AS FOLLOWS:

A-A-50186 CCC-C-438

TYPE I TYPE I, CLASSES 1 AND 2

TYPE II TYPE II, CLASS 1

TYPE III TYPE III, CLASS 1

TYPE IV TYPE III, CLASS 2

TYPE V TYPE IV, CLASS 1

TYPE VI TYPE IV, CLASS 2"

(ref. T1034 - May 19, 2006)