SPE1C1-16-R-0105_Tech_Data.docx

Coveralls, Flyer’s, Men’s, Tan 1654, PGC 03845

SECTION C- DESCRIPTION/SPECIFICATION

COVERALLS, FLYER'S, MEN'S, SUMMER, FLAME-RESISTANT

STYLE CWU-27/P

TYPE 1, CLASS 2, AF TAN 1654

SHALL BE PRODUCED IN ACCORDANCE WITH YACL-WP PD-99-01 R, DATED 20 APRIL 2001.

PATTERN DATE: 01 SEP 06

STANDARD SAMPLE OF AF TAN 1654 IS AVAILABLE UNDER ROLL # 11-06

INTERIM CHANGES TO YACL-WP PD 99-01:

Page 1, Paragraph 1.2 Classification, Delete "Sage Green 1590" and replace with "Sage Green 1659" Delete "Tan 380" and replace with "Tan 1654"

Page 3, Paragraph 3.3.1 Basic Material, Delete "1590" and replace with "1659" Delete "380" and replace with "1654"

Page 4, Table I. Hook and Loop Fastener Tape Lengths (inches) Under "Waist Loop" ADD:

Page 4, Paragraph 3.3.6, After "Nylon Cord." ADD the following: " The nylon cord for the lanyard and the cord beading in the edges of the slide fasteners shall be natural in color conforming to Type IA of MIL-C-5040."

Page 11-15, Operations 6-h, 7-b, 8-b, 9-b, and 14-b, delete stitch type "SSa-1" and substitute: "LSb-1".

Page 12, Table VII, Operation 7A: DELETE "LSb-2" and SUBSTITUTE "LSb-1"

Page 13, Table VII, Operation 10. g, add: "Note: The grommet should be on the side closest to the left thigh pocket.

Page 17, Operation 24, Joining lower leg pocket, last line, delete: "(4 inches up from the finished hem)" and substitute: "Bottom edges of pockets are 3-3/4" above finished hems at side seams and approximately 4" above finished hems at front and back corners.".

Page 18, Table VII, Operation 27. a, add: "Note: Five rows of stitching are required."

Page 18, Table VII, Operation 27. a, under Seam & Stitching type column delete: "LSd-2" and substitute:

"LSb-2"

Page 19, Table VII, Table of Operations, Operation 33:

DELETE: "1 inches from the neck seam" ADD: "1 inch from the Hanger Loop"

Page 23, paragraph 4.3, the following inspection levels apply to end item quality conformance inspection :

For visual examinatin the inspection level shall be II, the AQL for majors shall be 1.5, the AQL for minors shall be 4.0.

For dimensional examination the inspection level shall be S-1, the AQL shall be 1.5.

For packaging examination, the inpsection level shall be S-2, the AQL shall be 2.5.

For palletiazation the inspection level shall be S-2, the AQL shall be 6.5.

Page 32, Figure 5, Pocket Length, delete "5-7/8" and replace with "5-3/4".

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

THREAD, ARAMID, SPUN STAPLE, A-A-55217B, DATED 29 MARCH 2011

ADDITIONAL INFORMATION FOR A-A-55217

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436,

ROLL #3728, (THE FOLIAGE GREEN 502 AREA OF THE PATTERN)

AND REFERENCE FOR SHADE ONLY.

INTERIM CHANGES TO MIL-DTL-10884H:

PAGE 1, PARA. 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 - WHITE".

PAGE 8, PARA. 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY.

PAGE 8, AFTER PARA. 3.4.5, ADD NEW PARA. AS FOLLOWS: "3.4.6 FINISH 6 - WHITE. REFERENCE PARA. 3.4.5 EXCEPT THE COLOR SHALL BE WHITE."

CIELAB readings are provided as an informational tool only. The readings provided were taken using American Association Of Textile Chemists and Colorists (AATCC) Evaluation Procedure 6,(D65 /10 degree) unless a smaller aperture is needed for digital prints. It is recommended that suppliers take a reading of the standard shade sample provided by DLA Troop Support with their own Spectrophotometer. Due to different equipment models, different equipment condition, software, and calibration of equipment, readings taken by the ESA may differ from contractor readings, these readings are only one piece of information and are provided for information purposes only. Matching CIELAB readings as provided may or may not produce an acceptable match to the shade standard provided by DLA Troop Support. The CIELAB readings will not be used for shade acceptance evaluation. All shade acceptance evaluation will be based on Government visual shade evaluations only.

STANDARD SAMPLE FOR MIL-C-83429, Sage Green 1590, ROLL 99-2, IS APPLICABLE FOR SHADE AND COLORFASTNESS ONLY.

SG 1590 L* 38.76 a* -3.97 b*5.19

Full Tolerance DL* -1.40 Da* 0.07 Db* 0.50 DECMC 0.93 Blue Tolerance DL* 0.00 Da* -0.25 Db*-0.38 DECMC 0.54 Red Tolerance DL* -0.15 Da* 0.27 Db* 0.39 DECMC 0.56

ADDITIONAL INFORMATION FOR MIL-C-83429B:

STANDARD SAMPLE FOR SHADE AF TAN 1654 IS IDENTIFIED AS ROLL NO. 11-06 AND REFERENCED FOR SHADE, APPEARANCE AND COLORFASTNESS.

STANDARD SAMPLE FOR NAVY BLUE SHADE 3374 IS

IDENTIFIED AS ROLL NO. 85140 AND REFERENCED FOR

SHADE, FINISH AND COLORFASTNESS.

STANDARD SAMPLE FOR TYPE II, CLASS 5, 4-COLOR

WOODLAND CAMOUFLAGE IS IDENTIFIED AS ROLL NO.

3700 AND REFERENCED FOR SHADE, APPEARANCE AND

COLORFASTNESS.

STANDARD SAMPLE FOR UNIVERSAL CAMOUFLAGE

IS ROLL # 3765, REFERENCED FOR

SHADE ONLY.

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS

MIL-C-44436, ROLL # 3729 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN), FOR SHADE ONLY.

INTERIM CHANGES TO MIL-C-83429 ARE AS FOLLOWS:

PAGE 6, ADD NEW SPECTRAL REFLECTANCE TABLE: TABLE IIB SPECTRAL REFLECTANCE REQUIREMENTS, TYPE II CLASS 6, SAGE GREEN 1590

WAVELENGTH NANOMETER MIN. MAX.

600 6 12 620 6 12 640 7 15 660 7 18 680 8 18 700 8 18 720 12 22 740 16 28 760 22 35 780 28 40 800 32 45 820 36 52 840 40 58 860 46 64

PAGE 8, DELETE PARA.3.12 SEAM EFFICIENCY.

PARAGRAPH 1.2, ADD THE FOLLOWING CLASS:

"CLASS 9 - UNIVERSAL CAMOUFLAGE PRINTED"

PAGE 16, PARA. 6.6, ANTISTATIC PROPERTIES,

DELETE THE LAST SENTENCE IN ITS ENTIRETY.

ADDITIONAL INFORMATION FOR FED-STD-191:

FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.

INTERIM CHANGES TO FED-STD-191A:

TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".

TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".

THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT.

METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE."

METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."

PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY."

METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".

PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-".

PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.

NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."

PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY.

PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."

PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."

PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."

PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D".

AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST."

(Ref. T0215)

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

Examine Defect

Marking Omitted; incorrect; illegible, of (exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, sequence or method of appli-cation.

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

Testing Information The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE SWATCHES SHALL BE FORWARDED TO:

DLA

Product Testing Center, DSCC Lab, 700 Robbins Avenue, Philadelphia, Pa. 19111 EMAIL: jamie.hieber@dla.mil

PHONE: 1-215-737-3265

FOR PHYSICAL (NON-SHADE) TESTING: THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THE QAR WILL FORWARD THE COMPLETED DD FORM 1222. SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111 Attn: Bldg. 5D Telephone: 215 737 3240

SECTION D – PACKAGING AND MARKING

Case Lot is 20 coveralls per box.

As a minimum item shall be packed in a snug fitting fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC, Grade 275, variety SW, Class domestic, with a double wall liner. Any commercial closure method cited in ASTM-D-1974 is acceptable except stapling. Packaging shall be as per ASTM-D-3951, MIL-STD-129 with change notice 4, MIL-STD-147. Lot numbering shall be in accordance with MIL-STD-129 AND DSCP-4155.3

General inspection level II in accordance with the latest version of ANSI.ASQ Z1.4 for visual and dimensional. AQL 2.5 for majors, 4.0 for minors.

Coveralls, Flyer’s, Women’s, Type II, Class II (Tan 1654) PGC 03848

NSN Size UPC

8410-01-600-9242 30 M SHT 718020518565

8410-01-600-9243 30 M REG 718020490540

8410-01-600-9244 30 M LNG 718020548074

8410-01-600-9245 32 M SHT 718020576480

8410-01-600-9253 32 M REG 718020481944

8410-01-600-9255 32 M LNG 718020545417

8410-01-600-9256 34 M SHT 718020139609

8410-01-600-9257 34 M REG 718020450919

8410-01-600-9258 34 M LNG 718020545356

8410-01-600-9259 36 M SHT 718020483733

8410-01-600-9260 36 M REG 718020089416

8410-01-600-9261 36 M LNG 718020455372

8410-01-600-9262 38 M SHT 718020531236

8410-01-600-9263 38 M REG 718020487298

8410-01-600-9264 38 M LNG 718020076942

8410-01-600-9265 40 M SHT 718020075259

8410-01-600-9266 40 M REG 718020509136

8410-01-600-9267 40 M LNG 718020534008

8410-01-600-9269 42 M SHT 718020509396

8410-01-600-9268 42 M REG 718020058528

8410-01-600-9270 42 M LNG 718020448749

8410-01-600-9271 44 M SHT 718020564234

8410-01-600-9274 44 M REG 718020479071

8410-01-600-9275 44 M LNG 718020510668

8410-01-600-9283 30 W SHT 718020549811

8410-01-600-9284 30 W REG 718020513379

8410-01-600-9285 30 W LNG 718020550749

8410-01-600-9286 32 W SHT 718020102542

8410-01-600-9287 32 W REG 718020078199

8410-01-600-9288 32 W LNG 718020088266

8410-01-600-9289 34 W SHT 718020083575

8410-01-600-9290 34 W REG 718020440569

8410-01-600-9291 34 W LNG 718020557175

8410-01-600-9292 36 W SHT 718020115436

8410-01-600-9294 36 W REG 718020452357

8410-01-600-9295 36 W LNG 718020443768

8410-01-600-9296 38 W SHT 718020590509

8410-01-600-9297 38 W REG 718020111711

8410-01-600-9298 38 W LNG 718020548081

8410-01-600-9299 40 W SHT 718020504261

8410-01-600-9302 40 W REG 718020510125

8410-01-600-9301 40 W LNG 718020491585

8410-01-600-9306 42 W SHT 718020138787

8410-01-600-9304 42 W REG 718020450865

8410-01-600-9307 42 W LNG 718020065250

8410-01-600-9308 44 W SHT 718020472003

8410-01-600-9309 44 W REG 718020092898

8410-01-602-9074 44 W LNG 718020556215

ITEM DESCRIPTION

COVERALLS, FLYER'S, WOMEN'S, CWU-27/P

COVERALLS SHALL BE MADE IN ACCORDANCE WITH TYPE II, CLASS I OF FNS PD 99-04 DATED 28 APRIL 2003.

PATTERN DATE: 28 February 2013 Note: Specify "Navy Pattern" on request form.

STANDARD SAMPLE FOR SHADE AND COLORFASTNESS SHALL CONFORM TO TYPE II, CLASS 6, OF MIL-C-83429B DATED 26 SEPTEMBER 1990.

STANDARD SAMPLE FOR AF Tan 1654, CLOTH, PLAIN WEAVE, FLAME RESISTANT IS AVAILABLE UNDER ROLL NUMBER 11-06.

DEVIATION/CHANGES TO FNS PD 99-04 DATED 28 APRIL 2003.

PAGE 8 AND 9, TABLE VI, DELETE AND SUBSTITUTE:

Table VI: List of Pattern Parts - Type II only

Pattern Part CAD Pattern Nomenclature Cut Pieces

1. Front FRONT 2

2. Front Facing FRT_FACING 2

3. Top Back UPPER_BACK 1

4. Lower Back LWR_BK 2

5. Upper Collar TOP-COLLAR 1

6. Under Collar UNDER-COLLAR 1

7. Collar Interlining COLLAR-INT 1

8. Shoulder Patch SHLDR-PATCH 2

9. Back Belt Casing BACK_BELT 1

10. Top Sleeve TOP_SLEEVE 2

11. Under Sleeve UNDR_SLEEVE

12. Breast Pocket BRST_POCKET 2

13. Breast Pocket Slide Fastener Cover B_PKT_COVER 2

14. Sleeve Pocket SLEEVE_PKT 1

15. Sleeve Pocket Slide Fastener Cover S_PKT_COVER 1

16. Pencil Pocket PENCIL_PKT 1

17. Pencil Pocket Flap PENCIL_FLAP 1

18. Right Thigh Pocket R_THIGH_PKT 1

19. Right Thigh Pocket Slide Fastener Cover R_THIGH_CVR 1

20. Left Thigh Pocket L_THIGH_PKT 1

21. Left Thigh Pocket Slide Fastener Cover L_TGH_COVER 1

22. Lower Leg Pocket LEG_POCKET 2

23. Lower Leg Pocket Slide Fastener Cover LEG_COVER 2

24. Knife Pocket KNIFE_PKT 1

25. Knife Pocket Backing K_P_BACKING 1

26. Knife Pocket Flap KNIFE_FLAP 1

27. Leg Slide Fastener Cover GUSSET_CVR 4

28. Protective Fly FLY 2

29. Front Belt Tabs WAIST_ADJ 2

30. Sleeve Tabs SLV_ADJ 2

31. Thong THONG 1

32. Hanger HANGER 1

33. Front Slide Fastener Cover ZIP_COVER 2

34. Knife Pocket Reinforcement WEBBING

35. Leg Pocket Guide L_PKT_GUIDE

PAGE 11, OPERATION 8, SLEEVE POCKET PREPARATION, LINE 6 AND 7, DELETE "THE POCKET SHALL FINISH 5-7/8 INCHES LONG BY 4-1/4 INCHES WIDE" AND SUBSTITUTE "THE POCKET SHALL FINISH 5-3/4 INCHES LONG, BY 4-1/4 INCHES WIDE."

PAGE 25, PARAGRAPH 4.3, QUALITY CONFORMANCE INSPECTION, AT END OF PARAPRAGH ADD "IMPORTANT NOTICE: PARA-ARAMID THREAD IS NOT PERMITTED."

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

THREAD, ARAMID, SPUN STAPLE, A-A-55217, DATED 16 MARCH 2007

ADDITIONAL INFORMATION FOR A-A-55217

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436,

ROLL #3728, (THE FOLIAGE GREEN 502 AREA OF THE PATTERN)

AND REFERENCE FOR SHADE ONLY.

INTERIM CHANGES TO MIL-DTL-10884H:

PAGE 1, PARA. 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 - WHITE".

PAGE 8, PARA. 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY.

PAGE 8, AFTER PARA. 3.4.5, ADD NEW PARA. AS FOLLOWS: "3.4.6 FINISH 6 - WHITE. REFERENCE PARA. 3.4.5 EXCEPT THE COLOR SHALL BE WHITE."

ADDITIONAL INFORMATION FOR MS 27980E

FASTENER, SNAP, STYLE 2, (REGULAR WIRE

SPRING CLAMP TYPE), 30 NOV. 84

ADDITIONAL INFORMATION FOR MIL-C-83429B:

STANDARD SAMPLE FOR SHADE AF TAN 1654 IS IDENTIFIED AS ROLL NO. 11-06 AND REFERENCED FOR SHADE, APPEARANCE AND COLORFASTNESS.

STANDARD SAMPLE FOR NAVY BLUE SHADE 3374 IS

IDENTIFIED AS ROLL NO. 85140 AND REFERENCED FOR

SHADE, FINISH AND COLORFASTNESS.

STANDARD SAMPLE FOR TYPE II, CLASS 5, 4-COLOR

WOODLAND CAMOUFLAGE IS IDENTIFIED AS ROLL NO.

3700 AND REFERENCED FOR SHADE, APPEARANCE AND

COLORFASTNESS.

STANDARD SAMPLE FOR UNIVERSAL CAMOUFLAGE

IS ROLL # 3765, REFERENCED FOR

SHADE ONLY.

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS

MIL-C-44436, ROLL # 3729 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN), FOR SHADE ONLY.

INTERIM CHANGES TO MIL-C-83429 ARE AS FOLLOWS:

PAGE 6, ADD NEW SPECTRAL REFLECTANCE TABLE: TABLE IIB SPECTRAL REFLECTANCE REQUIREMENTS, TYPE II CLASS 6, SAGE GREEN 1590

WAVELENGTH NANOMETER MIN. MAX.

600 6 12 620 6 12 640 7 15 660 7 18 680 8 18 700 8 18 720 12 22 740 16 28 760 22 35 780 28 40 800 32 45 820 36 52 840 40 58 860 46 64

PAGE 8, DELETE PARA.3.12 SEAM EFFICIENCY.

PARAGRAPH 1.2, ADD THE FOLLOWING CLASS:

"CLASS 9 - UNIVERSAL CAMOUFLAGE PRINTED"

ADDITIONAL INFORMATION FOR ASTM-D3776:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION:

NO ADDITIONAL INFORMATION FOLLOWS.

NOTE: NASM16491, GROMMET, METALLIC APPLICATION

FOR COPIES SHOULD BE ADDRESSED TO:

AEROSPACE INDUSTRY ASSOCIATION OF AMERICA INC.

1250 EYE STREET, N.W. SUITE 1100,

WASHINGTON,DC 20005-3924.

ADDITIONAL INFORMATION FOR MIL-G-16491:

MIL-G-16491F IS CANCELLED - REPLACED BY NASM 16491.

NOTE: SPECIAL ATTENTION SHOULD BE GIVEN TO THE INSTALLATION OF THE FRONT SLIDE FASTENER AND SUBSEQUENT TOP STITCHING OF THE CENTER FRONT FACING TO ENSURE A MINIMUM AMOUNT OF TAKE-UP AT THE CENTER FRONT AND PUCKERING OF THE STITCHING.

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL". UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM".

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSN"s."

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

(exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

ADDITIONAL INFORMATION FOR MIL-PRF-121: BARRIER MATERIAL, GREASEPROOFED, WATERPROOFED, FLEXIBLE, 4/30/01.

NO ADDITIONAL INFORMATION FOLLOWS.

Testing Information The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE SWATCHES SHALL BE FORWARDED TO:

DLA

Product Testing Center, DSCC Lab, 700 Robbins Avenue, Philadelphia, Pa. 19111 EMAIL: jamie.hieber@dla.mil

PHONE: 1-215-737-3265

FOR PHYSICAL (NON-SHADE) TESTING: THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THE QAR WILL FORWARD THE COMPLETED DD FORM 1222. SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Testing Center Analytical Bldg. 5D, 700 Robbins Avenue Philadelphia, PA 19111 Attn: Elizabeth Torres

CASE LOT QUANTITY OF 10 COVERALLS.

GENERAL INSPECTION LEVEL II IN ACCORDANCE WITH THE LASTEST VERSION OF ANSI/ASQ Z1.4 FOR VISUAL AND DIMENSIONAL.

PACKAGING SHALL BE IN ACCORDANCE WITH BARRIER MATERIAL, GREASEPROOF, WATERPROOF, FLEXIBLE, HEAT-SEALABLE, MIL-PRF-121G, TYPE II WHICH IS NECESSARY TO PROVIDE PROTECTIO FROM EXPOSURE TO THE EXTREMES OF THE NAVAL AVIATION ENVIRONMENT.

AS A MINIMUM ITEM SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER CONFORMING TO ASTM-D-5118, TPYE CF STYLE RSC, GRADE 275, VERIETY SW, CLASS DOMESTIC, WITH A DOUBLE WALL LINER. ANY COMMERCIAL CLOSURE METHOD CITED IN ASTM-D-1974 IS ACCEPTABLE EXCEPT STAPLING.

PACKAGING SHALL BE AS PER ASTM-D-3951, MIL-STD-129 WITH CHANGE NOTICE 4, MIL-STD-147. LOT NIMBERING SHALL BE IN ACCORDANCE WITH MIL-STD-129 AND DSCP-4155.3.

Coveralls, Flyer’s, Women’s, Type I, Class 2 (Tan 1654) PGC 03847

NSN Size UPC

8410016009123 30 M XSH 718020501918

8410016009147 30 M SH 718020553146

8410016009143 30 M RG 718020477497

8410016009146 30 M LG 718020469478

8410016009162 32 M XSH 718020436050

8410016009163 32 M SH 718020576978

8410016009165 32 M RG 718020112381

8410016010737 32 M LG 718020088402

8410016009205 38 W XSH 718020548425

8410016009206 38 W SH 718020444895

ITEM DESCRIPTION

COVERALLS, FLYER'S, WOMEN'S, CWU-27/P

COVERALLS SHALL BE MADE IN ACCORDANCE WITH TYPE I, CLASS 2 OF FNS PD 99-04 DATED 28 APRIL 2003.

PATTERN DATE: 26 August 2002 Note: Specify "Air Force Pattern" on request form.

STANDARD SAMPLE FOR SHADE AND COLORFASTNESS SHALL CONFORM TO TYPE II, CLASS 6, OF MIL-C-83429B DATED 26 SEPTEMBER 1990.

STANDARD SAMPLE FOR AF TAN 1654, CLOTH, PLAIN WEAVE, FLAME RESISTANT IS AVAILABLE UNDER ROLL NUMBER 11-06.

DEVIATION/CHANGES TO FNS PD 99-04 DATED 28 APRIL 2003.

PAGE 11, OPERATION 8, SLEEVE POCKET PREPARATION, LINE 6 AND 7, DELETE "THE POCKET SHALL FINISH 5-7/8 INCHES LONG BY 4-1/4 INCHES WIDE" AND SUBSTITUTE "THE POCKET SHALL FINISH 5-3/4 INCHES LONG, BY 4-1/4 INCHES WIDE."

PAGE 25, PARAGRAPH 4.3, QUALITY CONFORMANCE INSPECTION, AT END OF PARAPRAGH ADD "IMPORTANT NOTICE: PARA-ARAMID THREAD IS NOT PERMITTED."

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

THREAD, ARAMID, SPUN STAPLE, A-A-55217, DATED 16 MARCH 2007

ADDITIONAL INFORMATION FOR A-A-55217

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436,

ROLL #3728, (THE FOLIAGE GREEN 502 AREA OF THE PATTERN)

AND REFERENCE FOR SHADE ONLY.

INTERIM CHANGES TO MIL-DTL-10884H:

PAGE 1, PARA. 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 - WHITE".

PAGE 8, PARA. 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY.

PAGE 8, AFTER PARA. 3.4.5, ADD NEW PARA. AS FOLLOWS: "3.4.6 FINISH 6 - WHITE. REFERENCE PARA. 3.4.5 EXCEPT THE COLOR SHALL BE WHITE."

ADDITIONAL INFORMATION FOR MS 27980E

FASTENER, SNAP, STYLE 2, (REGULAR WIRE

SPRING CLAMP TYPE), 30 NOV. 84

ADDITIONAL INFORMATION FOR MIL-C-83429B:

STANDARD SAMPLE FOR SHADE AF TAN 1654 IS IDENTIFIED AS ROLL NO. 11-06 AND REFERENCED FOR SHADE, APPEARANCE AND COLORFASTNESS.

STANDARD SAMPLE FOR NAVY BLUE SHADE 3374 IS

IDENTIFIED AS ROLL NO. 85140 AND REFERENCED FOR

SHADE, FINISH AND COLORFASTNESS.

STANDARD SAMPLE FOR TYPE II, CLASS 5, 4-COLOR

WOODLAND CAMOUFLAGE IS IDENTIFIED AS ROLL NO.

3700 AND REFERENCED FOR SHADE, APPEARANCE AND

COLORFASTNESS.

STANDARD SAMPLE FOR UNIVERSAL CAMOUFLAGE

IS ROLL # 3765, REFERENCED FOR

SHADE ONLY.

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS

MIL-C-44436, ROLL # 3729 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN), FOR SHADE ONLY.

INTERIM CHANGES TO MIL-C-83429 ARE AS FOLLOWS:

PAGE 6, ADD NEW SPECTRAL REFLECTANCE TABLE: TABLE IIB SPECTRAL REFLECTANCE REQUIREMENTS, TYPE II CLASS 6, SAGE GREEN 1590

WAVELENGTH NANOMETER MIN. MAX.

600 6 12 620 6 12 640 7 15 660 7 18 680 8 18 700 8 18 720 12 22 740 16 28 760 22 35 780 28 40 800 32 45 820 36 52 840 40 58 860 46 64

PAGE 8, DELETE PARA.3.12 SEAM EFFICIENCY.

PARAGRAPH 1.2, ADD THE FOLLOWING CLASS:

"CLASS 9 - UNIVERSAL CAMOUFLAGE PRINTED"

ADDITIONAL INFORMATION FOR ASTM-D3776:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR ASTM-D-6193(2004)OR LATEST VERSION:

NO ADDITIONAL INFORMATION FOLLOWS.

NOTE: NASM16491, GROMMET, METALLIC APPLICATION

FOR COPIES SHOULD BE ADDRESSED TO:

AEROSPACE INDUSTRY ASSOCIATION OF AMERICA INC.

1250 EYE STREET, N.W. SUITE 1100,

WASHINGTON,DC 20005-3924.

ADDITIONAL INFORMATION FOR MIL-G-16491:

MIL-G-16491F IS CANCELLED - REPLACED BY NASM 16491.

NOTE: SPECIAL ATTENTION SHOULD BE GIVEN TO THE INSTALLATION OF THE FRONT SLIDE FASTENER AND SUBSEQUENT TOP STITCHING OF THE CENTER FRONT FACING TO ENSURE A MINIMUM AMOUNT OF TAKE-UP AT THE CENTER FRONT AND PUCKERING OF THE STITCHING.

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL". UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM".

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSN"s."

Packaging examination. The fully packaged end item shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5.

(exterior) improper size, location, sequence & Unit Pack, or method of application.

Materials Any component missing, damaged or not as specified.

Workmanship Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling. Bulged or distorted container.

Contents Number of intermediate containers per shipping container is more or less than required.

Number of items per container is more or less than required.

Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged.

The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5.

Finished Length, width or height exceeds Dimensions specified maximum requirement.

Palleti- Pallet pattern not as specified.

zation Interlocking of loads not as specified. Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted; incorrect; illegible;

of improper size, location, MIL-STD-129P, WITH CHANGE 4 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR SHIPMENT AND STORAGE - DATED

19 SEPTEMBER 2007

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

ADDITIONAL INFORMATION FOR MIL-PRF-121: BARRIER MATERIAL, GREASEPROOFED, WATERPROOFED, FLEXIBLE, 4/30/01.

NO ADDITIONAL INFORMATION FOLLOWS.

Testing Information The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE SWATCHES SHALL BE FORWARDED TO:

DLA

Product Testing Center, DSCC Lab, 700 Robbins Avenue, Philadelphia, Pa. 19111 EMAIL: jamie.hieber@dla.mil

PHONE: 1-215-737-3265

FOR PHYSICAL (NON-SHADE) TESTING: THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THE QAR WILL FORWARD THE COMPLETED DD FORM 1222. SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Testing Center Analytical Bldg. 5D, 700 Robbins Avenue Philadelphia, PA 19111 Attn: Elizabeth Torres

CASE LOT QUANTITY OF 10 COVERALLS.

GENERAL INSPECTION LEVEL II IN ACCORDANCE WITH THE LASTEST VERSION OF ANSI/ASQ Z1.4 FOR VISUAL AND DIMENSIONAL.

PACKAGING SHALL BE IN ACCORDANCE WITH BARRIER MATERIAL, GREASEPROOF, WATERPROOF, FLEXIBLE, HEAT-SEALABLE, MIL-PRF-121G, TYPE II WHICH IS NECESSARY TO PROVIDE PROTECTIO FROM EXPOSURE TO THE EXTREMES OF THE NAVAL AVIATION ENVIRONMENT.

AS A MINIMUM ITEM SHALL BE PACKED IN A SNUG FITTING FIBERBOARD SHIPPING CONTAINER CONFORMING TO ASTM-D-5118, TPYE CF STYLE RSC, GRADE 275, VERIETY SW, CLASS DOMESTIC, WITH A DOUBLE WALL LINER. ANY COMMERCIAL CLOSURE METHOD CITED IN ASTM-D-1974 IS ACCEPTABLE EXCEPT STAPLING.

PACKAGING SHALL BE AS PER ASTM-D-3951, MIL-STD-129 WITH CHANGE NOTICE 4, MIL-STD-147. LOT NIMBERING SHALL BE IN ACCORDANCE WITH MIL-STD-129 AND DSCP-4155.3.