15-R-0091_AWC _Wmn's _Army_Sections_C D_PGC_02110.docx

COAT, WOMAN'S: ALL-WEATHER, DRESS, BLACK 385

ADDITIONAL INFORMATION FOR CR PD 03-09:

PATTERN DATE: 22 NOVEMBER 2002

STANDARD SAMPLE FOR CLOTH, POPLIN, POLYESTER

AND COTTON (WATER REPELLENT), ARMY BLACK 385

CONFORMING TO A-A-50531, IS AVAILABLE ON ROLL

NO. 3814, AND APPLICABLE FOR SHADE ONLY.

INTERIM CHANGES TO CR PD 03-09:

PAGE 1, PARA. 2, IN "SCHEDULE OF SIZES": ADD

SIZE 12 AND 14 FOR "EXTRA LONG"

PAGE 1, SCHEDULE OF SIZES, DELETE ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"SHORT REG LONG XLONG

XO XO XO ---

2 2 2 --- 4 4 4 --- 6 6 6 --- 8 8 8 --- 10 10 10 --- 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 --- 22 22 22 --- 24 --- --- --- 26 --- ---

PAGE 2, PARAGRAPH 3.1 DESCRIPTION. LINE 5

AFTER "5" ADD "THE MATERIAL FOR THE SLEEVE

LINING SHALL BE TAFFETA AS SPECIFIED

IN PARAGRAPH 3.3.2.2.)

LINE 5, DELETE "1/4" AND SUBSTITUTE "3/8".

PAGE 2, PARAGRAPH 3.1.2, BELT LOOP PLACEMENT.

LINE 1, AFTER "FINISHING" DELETE "1/2" AND

SUBSTITUTE "2-1/2".

PAGE 2, PARA. 3.1.2a SHOULDER STRAPS. DELETE

PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE THE

FOLLOWING PARAGRAPH: "3.1.2a SHOULDER STRAPS.

THE OVEREDGED STRAIGHT END OF SHOULDER STRAP

SHALL BE SEWN TO THE COAT WITH A 3/16 INCH SEAM

THEN FOLD STRAP TO THE FINISHED POSITION AND TOP

STITCH 1/4 INCH FROM THE FOLDED EDGE. THE

FINISHED SHOULDER STRAPS SHALL BE CENTERED ALONG

THE SHOULDER SEAM AND THE POINTED END SHALL

FINISH EVEN TO 1/2 INCH FROM THE COLLAR SETTING

SEAM. THE SHOULDER STRAPS SHALL FINISH SMOOTH

AND FLAT WITHOUT DISTORTION. THE SHOULDER STRAP

TOPSTITCHING SHALL FOLLOW THE TOP STITCHING LINE

OF THE FRONT SLEEVE SEAMS."

PAGE 2, PARAGRAPH 3.1.5, REMOVABLE LINER.

LINE 1, DELETE "SET IN SLEEVES" AND

SUBSTITUTE "1/2 RAGLAND SLEEVES".

LINE 3, AFTER ACCOMMODATE A" DELETE "27"

AND SUBSTITUTE "24".

PAGE 3, PARAGRAPH 3.1.5.1 DELETE ENTIRELY

PAGE 3, PARAGRAPH 3.2.2. BUTTONHOLES. LINE 4,

AFTER "ONE ON THE LEFT FRONT" INSERT "IN

HORIZONTAL ALIGNMENT WITH TOP BUTTON ON LEFT

FRONT" AND AFTER "ONE ON EACH LAPEL" INSERT

"AND THE CUT OPENING OF BUTTONHOLES SHALL BE

POSITIONED 3/4 INCH FROM EDGE OF COAT."

PAGE 3, PARAGRAPH 3.2.2, BUTTONHOLES.

AT END OF THE PARAGRAPH ADD:

"THERE SHALL BE TWO 3/4 INCH CUT, SQUARE BAR

TYPE BUTTONHOLES, ONE CENTERED ON THE BELT

FASTENER 3/8 INCH FROM THE END AND ONE

CENTERED ON THE RIGHT BACK VENT 3/4 INCH

FROM THE EDGE".

PAGE 3, PARAGRAPH 3.2.3 BUTTONS.

LINE 2, DELETE "18" AND SUBSTITUTE "45"

PAGE 3, PARAGRAPH 3.2.3, BUTTONS: AFTER "THE COAT SHALL HAVE THREE 24 LIGNE BUTTONS" DELETE "ONE BUTTON SHALL BE SEWN ON EACH SLEEVE LINING TO CORRESPOND WITH THE LOOPS ON THE REMOVABLE LINER'S SLEEVE BOTTOM AND ONE SHALL BE POSITIONED ON THE BELT FASTENER" AND INSERT "ONE BUTTON SHALL BE SEWN ON EACH SLEEVE LINING TO CORRESPOND WITH THE LOOPS ON THE REMOVABLE LINER'S SLEEVE BOTTOM AND ONE ON THE LEFT BACK VENT TO CORRESPOND TO THE BUTTONHOLE. THE COAT SHALL HAVE NINE 18 LIGNE BUTTONS; EIGHT ATTACHED TO THE 45 LIGNE BUTTONS ON THE COAT FRONT AND ONE POSITIONED ON THE BELT."

PAGE 3, AFTER PARAGRAPH 3.2.3 BUTTONS. INSERT

NEW PARAGRAPH AS FOLLOWS:"3.2.3.1 LAPEL BUTTON

PLACEMENT. THE TOP LEFT LAPEL BUTTON SHALL

BE POSITIONED SO THAT THE RIGHT COAT FRONT LAYS

SMOOTH AND FLAT WITHOUT DISTORTION AND THE

NECK OPENING SHALL BE 2 TO 2-1/2 INCHES BETWEEN

COLLARSTAND JOINING SEAM AND COLLARSTAND JOINING

SEAM ACROSS FRONT OF COAT."

PAGE 6, PARAGRAPH 3.3.2.4, LINE 2, AFTER

"COMBED COTTON" INSERT "OR STAPLE RAYON".

LINE 9: DELETE "2.5" AND SUBSTITUTE "1.5"

PAGE 6, PARAGRAPH 3.3.3, LINE 1, DELETE "1/4"

AND SUBSTITUTE "3/8".

PAGE 8, TABLE II, DELETE "SLEEVE LINER AND

BELT AND SUBSTITUTE "SLEEVE LINER AND BACK

VENT".

DELETE "STAY BUTTONS AND SUBSTITUTE "STAY

BUTTONS AND BELT" AND UNDER "TOTAL QUANTITY"

FOR STAY BUTTONS: DELETE "6" AND SUBSTITUTE "7"

PAGE 8, PARAGRAPH 3.4.9 DELETE ENTIRELY AND

SUBSTITUTE: "3.4.10 SLIDE FASTENER. THE

SLIDE FASTENER FOR THE COAT AND THE REMOVABLE

LINER SHALL BE A SEPARATING, NON-REVERSIBLE,

RIGHT-HAND, LIGHT SIZE WITH AN ALUMINUM

OR BRASS CHAIN, SHORT TAB PULL. THE LENGTHS OF

THE SLIDE FASTENERS SHALL CONFORM TO THE SIZE

COAT WITH A MINIMUM LENGTH OF 70 INCHES. THE

COLOR OF THE TAPE SHALL BE A GOOD MATCH TO THE

BASIC MATERIAL AND SHALL BE 7/16 OR 9/16 INCH

WIDE. THE ENDS OF THE SLIDE FASTENER SHALL

BE EQUIDISTANT FROM THE BOTTOM EDGE OF THE COAT.

PAGE 10, PARA.3.5 LABELS, ADD NEW PARAGRAPH

"3.5.4 DLA TROOP SUPPORT EXCLUSIVE LABEL. EACH COAT

SHALL HAVE THE DLA TROOP SUPPORT EXCLUSIVE LABEL SEWN

TO THE LEFT INSIDE FRONT FACING ABOVE THE

SIZE/INSTRUCTION LABELS. THE LABEL SHALL BE

APPROXIMATELY 2 INCHES WIDE AND BE SEWN

ON ALL FOUR SIDES."

PAGE 10, TABLE III, LIST OF PATTERN PARTS, DELETE "BACK VENT FACING" AND "POCKET FACING, CORD" AND INSERT "NECK FACING" AND "NECK FACING, FUSIBLE".

PAGE 11, PARA.3, FINISHED MEASUREMENTS, TABLE 1V

UNDER "BACK LENGTH TYPE II" FOR SIZE 12XL ADD "48"

AND FOR SIZE 14XL ADD "48 1/4"

PAGE 11, TABLE 1V COAT FINISHED MEASUREMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "16"

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 55-1/2 57-1/2

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 45-1/2 45-3/4

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 17 17

. LONG -- --

. XLONG -- --

BELT LENGTH TYPE II ONLY 55 57

PAGE 12, PARA. 3.1, LINER MEASUREMENTS, TABLE V

UNDER "BACK LENGTH, TYPE II" FOR SIZE 12XL ADD

"37-3/4" AND FOR SIZE 14XL ADD "38"

PAGE 12, TABLE V LINER FINISHED MEASUREMENTS

UNDER SLEEVE LENGTH, SIZE 22 SHORT DELETE "15"

UNDER SIZE ADD "SIZES 24 26

BREAST (1/) TYPE II ONLY 47 49

BACK LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 35-3/4 36

. LONG -- --

. XLONG -- --

SLEEVE LENGTH TYPE II ONLY

. SHORT -- --

. REGULAR 16 16

. LONG -- --

. XLONG -- --"

PAGE 16, PARAGRAPH 7.2.2 ASTM TEST METHODS

ADD "D-256 STANDARD TEST METHOD FOR IMPACT

RESISTANCE OF PLASTICS AND ELECTRICAL INSULATING

MATERIALS".

PACKAGING AND MARKING INSTRUCTIONS

TEN (10) ALL-WEATHER COATS, ONLY SIZE ONLY,

SHALL BE PACKED IN A SNUG-FITTING FIBERBOARD

SHIPPING CONTAINER CONFORMING TO ASTM-D5118,

TYPE CF, STYLE RSC, GRADE 275, VARIETY SW, CLASS

DOMESTIC WITH A DW LINER. THE DIMENSIONS OF THE

CONTAINER SHALL APPROXIMATE 20-H X 16-W X 24-L.

METHOD OF CLOSURE SHALL BE IN ACCORDANCE WITH

ASTM-D-1974, 2A2, FIGURE 1 OR AS AN ALTERNATE

2B6 OR 3B7, FIGURE 3.

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4

GENERAL INSPECTION LEVEL 2".

(Ref. W2853)

ADDITIONAL INFORMATION FOR A-A-50198A

THREAD, GIMP, COTTON, BUTTONHOLE

STANDARD SAMPLE FOR COLOR FOLIAGE GREEN 504,

IS MIL-C-44436, ROLL #3728, (THE FOLIAGE GREEN

502 AREA PF THE PATTERN) AND REFERENCE

FOR SHADE ONLY.

PACKAGING

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT

CODE (UPC) MUST BE PLACED ON ALL SHIPPING

TGI DATA:

52.246-11 Higher-Level Contract Quality Requirement (Feb 1999) ANSI/ISO/ASQ Q9001-2008(excluding para 7.3) or equivalent.

Certification or registration of a contractor's quality system or program is not required by DoD if ISO or ANSI/ASQ standards are used.

52.215-9017 (J15C02), LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

(APR 2008) - DLAD

(a) This solicitation/award consists of the following documents, exhibits, and other attachments:

(1) DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, NOVEMBER 3, 1997.

THE FIRST ARTICLE SHALL BE 50 UNITS EXAMINED AT THE CONTRACTOR'S PLANT FOR VISUAL AND DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH THOSE PARAS. CONTAINED IN SECTION 4 OF THE END ITEM SPECIFICATION ENTITLED "END ITEM VISUAL EXAMINATION" (OR "VISUAL EXAMINATION", AS APPLICABLE) AND "END ITEM DIMENSIONAL EXAMINATION" (OR "DIMENSIONAL EXAMINATION" OR "EXAMINATION OF FINISHED MEASUREMENTS", AS APPLICABLE) WITH THE EXCEPTION THAT ALL 50 UNITS WILL BE VISUALLY EXAMINED AND THE SAMPLE SIZE FOR DIMENSIONAL EXAMINATION SHALL BE 8: OR, WHEN SECTION 4 OF THE END ITEM SPECIFICATION CITES A MILITARY STANDARD PROVISION FOR EVALUATING QUALITY, THE VISUAL AND DIMENSIONAL EXAMINATION SHALL BE MADE IN ACCORDANCE WITH THOSE PARAS. OF THE MIL-STD ENTITLED "END ITEM EXAMINATION" AND "DIMENSIONAL EXAMINATION" WITH THE EXCEPTIONS NOTED ABOVE.

ADD THIS PARA TO 52.209-4

52.209-4, 52.209-9P01, WHEN 52.210-9P06 IS NOT INCLUDED, INSERT THE FOLLOWING: "IF THE EXAMINATION INDICATES ONE OF THE FOLLOWING: WHICHEVER IS APPLICABLE:

(1) NO DIMENSIONAL DEFECT IS FOUND AND NO MORE THAN 10% OF THE UNITS EXAMINED ARE FOUND TO CONTAIN MAJOR OR MINOR "A" DEFECTS, OR

(2) NO DIMENSIONAL DEFECT OR SELECTED DEFECT IS FOUND NOR MORE THAN 10% OF UNITS EXAMINED ARE FOUND TO CONTAIN 3 OR 2 POINT DEFECTS, OR

(3) WHEN THE CLASSIFICATION OF DEFECTS CONTAINS ONLY MAJOR OR MINOR DEFECTS OR ONE CLASS OF DEFECTS ONLY, NO DIMENSIONAL DEFECT IS FOUND NOR MORE THAN 10% OF THE UNITS EXAMINED ARE FOUND TO CONTAIN A DEFECT.

52.209-9019 (I09C25), REQUESTS FOR WAIVER OF FIRST ARTICLE TESTING REQUIREMENTS (SEP 2008) - DLAD

52.246-9031 (E46C11), SHADE EVALUATION (APR 2008) - DLAD.

100% SHADE SWATCHING IS APPLICABLE.

The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

GOVERNMENT LABORATORY TESTING OF COMPONENTS FOR ACCEPTANCE PURPOSE.

52.246-9030 SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

SHADE SAMPLING IS APPLICABLE

The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)°K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)°K.

ALL SAMPLES/SWATCHES SUBMITTED FOR TESTING UNDER THE NEW UNIVERSAL CAMOUFLAGE SHALL BE SENT FOR GOVERNMENT TESTING TO THE ADDRESSES NOTED BELOW.

FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE SWATCHES SHALL BE FORWARDED TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111

ATTN: BLDG 5D

EMAIL: jamie.hieber@dla.mil

PHONE: 215-737-3265

FOR PHYSICAL (NON-SHADE) TESTING: IN ACCORDANCE WITH CLAUSE 52.246-9032, THE CONTRACTOR'S APPROVED QUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THE QAR WILL FORWARD THE COMPLETED DD FORM 1222. SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPON REQUEST TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111

ATTN: BLDG 5D

PHONE: 215-737-3240

THE USE OF ELECTRONIC SUBMISSION OF DD FORM 1222 IS AUTHORIZED.

ADDITIONAL INFORMATION FOR ASL:

THE ACCEPTABLE SUPPLIER LISTING (ASL) AND QUALIFIED LABORATORY LISTING (QLL) ARE NO LONGER VALID DOCUMENTS AND WILL NOT BE PUBLISHED IN THE FUTURE. THE POINT OF CONTACT FOR QUESTIONS PERTAINING TO LABORATORIES AND SUPPLIERS IS THE PROCUREMENT BUYER, INDICATED IN THE SOLICITATION OR CONTRACT. QUESTIONS SHOULD BE PROVIDED IN WRITING TO THE DESIGNATED BUYER.

CLAUSE 52.246-9032 IDENTIFICATION OF QUALIFIED LABORATORY AND SOURCE SAMPLING APPLIES.

REVIEW OF THIS ITEM HAS DETERMINED THAT THE SPECIFICATIONS, STANDARDS, PRODUCT DESCRIPTIONS OR OTHER TECHNICAL DATA APPLICABLE TO THIS PROCUREMENT ACTION DO NOT REQUIRE THE USE

OF CLASS I OZONE DEPLETING SUBSTANCES (ODS) OR ODC(S).

INSPECTION AT SOURCE/ACCEPTANCE AT SOURCE

52.210-C002 - APPROVED FINISH(ES) OR TREATMENTS(S).

MANDATORY USE OF STATISTICAL PROCESS CONTROLS

I. GENERAL REQUIREMENTS:

A. THE OFFEROR AGREES TO MANAGE AND IMPROVE PROCESS PERFORMANCE THROUGH THE EVALUATION OF THE QUALITY OF THE PRODUCT AT THE PRIME CONTRACTOR AND/OR SUBCONTRACTOR FACILITIES, USING STATISTICAL PROCESS CONTROL (SPC) TECHNIQUES.

B. MINIMUM CRITERIA ARE ESTABLISHED IN THE AMERICAN SOCIETY OF QUALITY CONTROL (ASQC) STANDARDS B.1, B.2 AND B.3 (FORMERLY THE ANSI STANDARDS Z1.A, Z1.2 AND Z1.3). ALTERNATE SPC TECHNIQUES, SUCH AS SHORT RUN METHODS ARE ALSO ALLOWED WHERE APPLICABLE.

C. THIS QUALITY ASSURANCE PROVISION (QAP) APPLIES TO ALL WORK PERFORMED AT THE PRIME AND/OR SUBCONTRACTOR FACILITIES.

D. EXCLUSION OF SPC PLAN SUBMISSION: OFFERORS WHO CONSIDER THEMSELVES ELIGIBLE FOR EXCLUSION OF THE SPC PLAN SUBMISSION BASED ON SATISFACTORY UTILIZATION OF A PREVIOUSLY APPROVED SPC PLAN FOR THE IDENTICAL OR SIMILAR SUPPLIES ARE TO SUBMIT A WRITTEN REQUEST FOR EXCLUSION (RFE) TO THE PROCURING ACTIVITY.

52.215-9017 List of Documents, Exhibits, and other Attachments (Apr 2008) - DLAD

(a) This solicitation/award consists of the following documents, exibits, and other attachments:

(1) DSCPM 4155.3, Quality Systems Requirements, November 3, 1997. LOT NUMBERING REQUIRED.

(2) DLAD 5025.30, Defense Logistics Agency One Book, Quality Management Programs Process Chapter, Dated October 31, 2003.

52.246-15 CERTIFICATE OF CONFORMANCE

ADDITIONAL INFORMATION FOR COMMERCIAL AQL'S:

AQL'S FOR COMMERCIAL ITEM DESCRIPTIONS (CID'S):

VISUAL - GENERAL INSPECTION LEVEL II, AQL - 1.0

DIMENSIONAL - SPECIAL INSPECTION LEVEL S-2, AQL - 2.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE USE

OF "SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES", ANSI/ASQC Z1.4

VECP #1996024 SUBMITTED BY STERLINWEAR

OF BOSTON INC. CONTRACT SPO100-96-C-1006

COAT, ALL-WEATHER, MAN'S, A-A-55260

ROYALTY AMOUNT $0.52 EXPIRATION DATE 26 NOV 2000

"SECTION D - PACKAGING AND MARKING" AFTER SUPP-

LEMENTAL INSTRUCTIONS", AFTER "PACKAGING:"

DELETE AND SUBSTITUTE: "EACH COAT SHALL BE FOLD-

ED TO APPROXIMATELY 14 INCHES BY 22-1/2 INCHES.

EACH FOLDED COAT SHALL BE INSERTED INTO A CLOSE

FITTING FLAT STYLE CLEAR POLYETHYLENE BAG CON-

FORMING TO A-A-50083. THE BAG SHALL BE AT LEAST

1 INCH LONGER THAN THE FOLDED COAT. THE UNSEALED

OPENING OF THE BAG SHALL VE AT THE SMALLER

DIMENSION OF THE BAG.

TEN COATS OF ONE SIZE ONLY, PACKAGED AS SPECIF-

IED, SHALL BE PACKED IN A SHIPPING CONTAINER

THAT IS ASSEMBLED AND CLOSED TO CONFORM CLASS

DOMESTIC, VARIETY DW, GRADE 275, SIZE 3A OF MIL-

B-17757. THE FIBERBOARD FOR THE LINERS SHALL CON

FORM TO TYPE CF, CLASS DOMESTIC, VARIETY DW,

GRADE 275 OF PPP-F-320. EACH BAGGED COAT SHALL

BE PACKED FLAT, WITH EVERY OTHER COAT REVERSED

TOP TO BOTTOM WITHIN THE SHIPPING CONTAINER.

THE TOP AND THE BOTTOM OF THE CONTENTS OF THE

SHIPPING CONTAINER SHALL BE COMPLETEY COVERED

WITH A SHEET OF 30 POUND (MIN) BASIS WEIGHT

PAPER CONFORMING TO A-A203."