TECH-DATA_PGC02885-4-1-15.docx

TECH-DATA CR/PD 03-18D 04/01/2015

NSN 8440015084954 PGC: 02885

SOCKS, BOOT, ANTIMICROBIAL

TYPE II, COYOTE BROWN.

CR/PD 03-18D DATED 26 JUNE 2009

SOCK, BOOT, ANTIMICROBIAL, TYPE II, COLOR

COYOTE BROWN

ADDITIONAL INFORMATION FOR CR PD 03-18D:

PACKAGING AND PACKING SHALL BE IN ACCORDANCE

WITH ASTM -D 3951 (STANDARD PRACTICE FOR

COMMERCIAL PACKAGING). SHIPPING CARTONS SHALL BE

MARKED IN ACCORDANCE WITH PARAGRAPH 5.1.6.3

OF ASTM D3951 AND SHALL INCLUDE: SIZE, NSN

WITH UPC NUMBER AND BAR-CODE, THE CONTRACTOR'S

NAME/LOGO, CONTRACT NUMBER AND ITEM DESCRIPTION.

DEPOT SHIPMENTS SHALL BE MARKED IN ACCORDANCE

WITH MIL-STD-129P

AQLS SHALL BE AS FOLLOWS:

END ITEM DIMENSIONAL 4.0 - INSPECTION LEVEL S-3

VISUAL 4.0 - INSPECTION LEVEL II

Sampling: Applicable to Type II In the beginning of each contract, and annually hereafter the contractor must provide physical test reports for the end item. This requirement does not negate the contractors responsibility to perform evaluations and/or testing prior to shipping, nor does it affect the conditions of one for one warranty or any other warranty specified in the contract. Delays caused by failure to provide test report s will be considered inexcusable unless the Contractor can clearly show that they are not at the fault of the contractor or of any of its subcontractors.

DSCP reserves their right to perform testing on a as needed basis.

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:

MIL-STD-147E DEPARTMENT OF DEFENSE

16 MAY 2008 STANDARD PRACTICE

PALLETIZED UNIT LOADS

STANDARDS (COMMERCIAL)

ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets.

52.246-2, Inspection of Supplies - Firm-Fixed Price 52.209-4, Alt. I, First Article Approval - Government Testing

52.215-9017 List of Documents, Exhibits, and other Attachments (Apr 2008) - DLAD

(a) This solicitation/award consists of the following documents, exibits, and other attachments:

(1) DSCPM 4155.3, Quality Systems Requirements, November 3, 1997. LOT NUMBERING REQUIRED.

(2) DLAD 5025.30, Defense Logistics Agency One Book, Quality Management Programs Process Chapter, Dated October 31, 2003.

GOVERNMENT LABORATORY TESTING OF COMPONENTS FOR ACCEPTANCE PURPOSE.

52.246-9030 (E46C10), SHADE EVALUATION OF CONTRACTOR FURNISHED COMPONENTS (APR 2008) - DLAD. SHADE SAMPLING IS APPLICABLE

The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200) deg K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)deg K.

Marking shall be in accordance with MIL-STD-129 and Notice 3.

Fiberboard shipping container conforming to ASTM-D-5118, Type CF, Style RSC-L (iner), Grade 275, variety SW, Class domestic Any commercial closure method cited in ASTM-D1974 is acceptable except stapling

Case lot is: 144

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required (ref. T8379; Nov. 08, 2006)

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)