Spade_Damper_13006481.pdf

A

B

C

D

E

F

A

B

C

D

E

F

8 7 6 5 4 3 2 1DRAWING SIZE F

SIZE CAGE CODE

SCALE SHEET

FORMAT: F_TACOM_ENG_1_0

UNIT WT.

DESIGN ACTIVITYCONTRACT NUMBER

CONTRACTOR

DRAWN BY DATE (YEAR-MO-DA)

CHECKER ENGINEER

ENGINEER QUALITY ENGINEER

DRAWING APPROVAL

DESIGN APPROVAL

THIRD ANGLE PROJECTION

MATL ENGR MODELED BY

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ON ANGLES �#� �$�

2 PLACE DECIMALS �#�

3 PLACE DECIMALS �#�

PMIC

12345678

DWG NO.

BMG2005-09-29

PRODUCT BASELINE

ERR LO5A2024

BOLT CENTERLINE

5.12

R.25

4.72

1.42

.76

3.94

4.29

20�$�

6.50

4X .85 4X 2.75

8X R.0625

8X �n�

EQUALLY SPACED

.750

.53

4X �n�

THRU HOLE

.50

4.76

4.76

FREE STATE

4.00

(20.75

11.29

2X

ACROSS FLATS

4.12

60.0�$�

SR6.00

6.10

4.375

(4.75)

( )4.54

REVISIONS

APPROVEDDATE(YEAR-MO-DA)DESCRIPTIONREVISION

GJC2017-09-12NOR L17A2064 / 2017-08-22A

1 OF 10.000 8/1

1300648119200F

DAMPER, SPADE

US ARMY

ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER

PICATINNY ARSENAL, NEW JERSEY 07806-5000

J. STANILIOUS 2005-08-17

J.STANILIOUS

JOSEPH LIPINSKI 2005-09-29

GABRIEL JARANI 2005-09-29

DO NOT SCALE DRAWING

JJS

M777 HOWITZER

NEXT ASSY USED ON

APPLICATION

MECHANICAL

PROPERTIES

YP

TS

EL2

RA

BH

RH

PART NO. 13006481

THIS DRAWING WAS GENERATED FROM A SOLID MODEL

AND IS CAD MAINTAINED. CHANGES SHALL BE

INCORPORATED BY THE DESIGN ACTIVITY.

NSN (NATIONAL STOCK NUMBER, IF NONE SO STATE)

APPROVED SOURCE(S) OF SUPPLY

PART NO.

VENDOR VENDOR

PART NO.ADDRESS CAGE CODE

13006481

TAYLOR DEVICES, INC.

90 TAYLOR DRIVE

N. TONAWANDA, NY 14120-0748

06742 67DP-17575-01

.02

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

A. ASME Y14.100-2000

B. ASME Y14.5M-1994

2. QAP 13006481 APPLIES.

3. MATERIAL: OUTER SLEEVE IS 7075-T7351 HARD COAT ANODIZED

ALUMINUM; PLUNGER IS CHROME PLATED CRES.

4. PART DESCRIPTION: A COMPRESSION ACTING HYDRAULIC

SHOCK ABSORBER WITH COIL SPRING RESET.

5 .TECHNICAL INFORMATION:

A.RESETTING SPRING DATA:

1) RESETTING FORCE AT FULLY EXTENDED POSITION =125 LBS

2) RESET TIME: 2 SECONDS MAX

B.OUTPUT PARAMETERS:

1) UNIT STROKE: 4.75 FULL COMPRESSION; 4.375 STROKE PRIOR

TO HITTING BOTTOM STOP.

2) IMPACT VELOCITY: 20 IN/SEC

3) IMPACT FORCE: TO BE 60,000 LBS, NOMINAL.

C.APPROX. UNIT WEIGHT: 39 LBS MAX

D.OPERATING TEMPERATURE RANGE: -51�$�F TO 120�$�F.

E.STORAGE TEMPERATURE RANGE: -51�$�F TO 160�$�F.

F.RELIABILITY: 15,900 CYCLES @ MAX. LOAD.

6. PROTECTIVE FINISH: PRIOR TO ASSEMBLY APPLY FINISH 4.10

OR 4.9 TO OUTER SLEEVE, THEN APPLY FINISH 7.5 IN ACCORDANCE

WITH MIL-STD-171. PLUNGER SHALL BE FREE OF OIL, GREASE AND

DIRT PRIOR TO APPLICATION OF CHROME PLATING.

7. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN

PROCURED FROM THE VENDOR(S) LISTED HEREON

IS APPROVED BY ARDEC PICATINNY ARSENAL,

NEW JERSEY 07806-5000 FOR USE IN THE

APPLICATION(S) SPECIFIED HEREON. A SUBSTITUTE

ITEM SHALL NOT BE USED WITHOUT PRIOR APPROVAL

BY ARDEC.

8. IDENTIFICATION OF THE APPROVED SOURCE(S) OF

SUPPLY HEREON IS NOT TO BE CONSTRUED AS A

GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY

AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED

ON THE DRAWING.

9 ITEM IDENTIFICATION: APPLY THE FOLLOWING MARKING

TO PART BY STAMP, ENGRAVE OR DOT PEEN WITH

.156�#�.015 HIGH CHARACTERS BY .005+.010 DEEP.

IN ACCORDANCE WITH MIL-STD-130.

"19200-13006481"

MFR- -

10 ITEM IDENTIFICATION: APPLY THE FOLLOWING MARKING

TO PART "S/N[ ]" BY ELECTRO-ETCH PROCESS.

MARKINGS TO BE CLEARLY VISISBLE AND LEGIBLE,

HEIGHT OF .25 +/- .01 IN.

SERIAL NUMBER TO BE ASSIGNED BY CONTRACTOR.

DISTRIBUTION STATEMENT A:

APPROVED FOR PUBLIC RELEASE;

DISTRIBUTION IS UNLIMITED.

SOURCE CONTROL DRAWING

(NOTE: PLUNGER STROKES

BELOW FLUSH)

ISO_VIEW

SCALE 1/4

MANUFACTURER'S

CAGE CODE PART NO.

IN-PROCESS DIMENSION OF

AVAILABLE STROKE BEFORE

INSERTION INTO SLEEVE

PLUNGER

OUTER SLEEVE

PLUNGER PRIOR TO

HITTING BOTTOM STOP

PLUNGER AT

FULL COMPRESSION

SECTION A-A