Attachment_2_SPI_NO._AM9390000.pdf

DD FORM 2169, JUN 1997 Previous editions are obsolete Page 1 of 5 Pages

* SPECIFICATIONS, STANDARDS AND DRAWINGS LISTED HEREON OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID FORM A PART OF THIS PACKAGING INSTRUCTION. THE APPLICABLE GENERAL AND REFERENCED REQUIREMENTS OF SPECIFICATION MIL-STD-2073-1 FORM PART OF THESE INSTRUCTIONS. UNLESS OTHERWISE SPECIFIED, MATERIALS WILL BE MINIMUM SIZE IN ACCORDANCE WITH MIL-STD-2073-1. WEIGHTS AND SIZES ARE ESTIMATED AND MAY VARY SLIGHTLY. INTERMEDIATE PACKAGING AND PACKING WILL BE IN ACCORDANCE WITH

SPECIFICATION MIL-STD-2073-1 OR AS OTHERWISE SPECIFIED HEREIN.

TOLERANCES SHALL BE IN ACCORDANCE WITH MATERIAL SPECIFICATIONS. QUALITY PERFORMANCE AND TESTING REQUIREMENTS SHALL BE IN CONFORMANCE WITH MIL-STD-2073-1, OR AS OTHERWISE SPECIFIED.

A. UNLESS OTHERWISE SPECIFIED, CLEANING AND DRYING SHALL BE IN ACCORDANCE WITH PARAGRAPH 5.2.1 OF

MIL-STD-2073-1. THE RIFLE SHALL BE DISASSEMBLED AS NECESSARY TO ACCOMPLISH THE SPECIAL CLEANING OF BURNED POWDER RESIDUE. SURFACES OF COMPONENTS SUBJECTED TO BURNED POWDER RESIDUES SUCH AS THE BOLT AND BOLT CARRIER ASSEMBLY, FIRING PIN, BARREL BORE, AND CHAMBER, ETC, SHALL BE SCRUBBED CLEAN WITH A BRISTLE BRUSH AND/OR SWABS SATURATED WITH RIFLE BORE CLEANER CONFORMING TO MIL-PRF-

372. FLUSH THE SCRUBBED SURFACES WITH SOLVENT CONFORMING TO P-D-680. ALL CLEANED SURFACES SHALL BE THOROUGHLY DRIED PRIOR TO PRESERVATIVE APPLICATION. DRYING SHALL BE WITH PREPARED COMPRESSED AIR, EXCEPT FOR THE BARREL BORE, CHAMBER, AND FLASH SUPPRESSOR, WHICH SHALL BE DRIED

BY WIPING WITH CLEAN, LINT-FREE SWABS.

B. ALL METALLIC SURFACES OF THE RIFLE SHALL BE COATED WITH MIL-PRF-32033, APPLIED BY BRUSHING OR SPRAYING. EXCESS OIL SHALL BE THOROUGHLY DRAINED FROM THE COATED SURFACES. THE PRESERVED RIFLE SHALL BE ALLOWED TO DRAIN FOR A MINIMUM OF ONE HOUR PRIOR TO CONTINUING WITH THE PACKAGING

PROCESS.

WSC: HF ITEM SIZE: 30.6 X 8.0 X 2.7 ITEM WEIGHT: 7.8 APPROVED: BRADFORD J. FOLEY

DISTRIBUTION STATEMENT A; APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE IDENT 3. SPI NO.

9390000 CARBINE, 5.56MM, M4 19200 AM9390000

4. NATIONAL STOCK NO. 5. DATE OF DRAWING / SPI

(YYMMDD)

6. REVISION / ERR NO.

1005-01-231-0973 080726 D/L07S3073

7. QUP 8. ICQ 9. UNIT PACK WT. (LB) (0.0) 10. UNIT PACK CU. (CU.

FT.)(0.00)

11. UNIT PACK SIZE (INCHES) (00.0)

1/EA 50 8.6 0.675 32.5 x 9.7 x 3.7

12. MILITARY PRESERVATION (METHOD) 18.

STEPS

19.

REQ’D

20.

DESCRIPTION

MIL-STD-2073-1 – METHOD 31 1(B) AR PRESERVATIVE: MIL-PRF-32033

13. CLEANING 2(C) 1 DRW # 7266299 VCI TREATED BORE TUBE (M4)

SEE NOTE A & B 3(C) 1 SEE NOTE C

14. DRYING 4(D) 2 BLOCKING: A-A-59136; OR ASTM D4724

SEE NOTE A & B 5(E) 1 CONTAINER: ASTM D5118, ST-RSC, GR-W5c, CL-WR

15. PACKING 6(E) CLOSURE: ASTM D1974, SEALING METHOD B

a. LEVEL A

MIL-STD-2073-1, SEE NOTE F

b. LEVEL B

MIL-STD-2073-1, SEE NOTE F

16. MARKING

MIL-STD-129, SEE NOTE G

17. NOTES / DRAWINGS

DD FORM 2169, JUN 1997 Previous editions are obsolete Page 2 of 5 Pages

C. INSERT VCI BORE TUBE INTO BARREL. ASSURE THAT THE HAMMER IS IN THE FIRED POSITION (AGAINST THE BOLT CATCH), AND THE FIRING PORT COVER IS LATCHED SHUT. INSERT RIFLE INTO BAG; EXHAUST EXCESS AIR, AND SEAL CLOSE. BAG SHALL BE NON-TOXIC, TRANSPARENT, 4 MIL THICK POLYETHYLENE FILM HAVING A MULTI- METAL VOLATILE CORROSION INHIBITOR. BAG SHALL BE FABRICATED IN ACCORDANCE WITH MIL-DTL-117, FOR A

CLASS-B BAG, SUGGESTED SOURCES OF SUPPLY:

MANUFACTURER PRODUCT

CORTEC VPCI 126

DAUBERT-CROMWELL CLEAR PAK 3000

ZERUST ICT510-C MULTI-METAL

COMPATIBITILITY TEST AND PROVISIONS OF MIL-I-8574 APPLY.

D. DESIGN AND FABRICATE / ASSEMBLE FROM SHEET STOCK AND OR DIE CUTS. BLOCKING IS TO IMMOBILIZE RIFLE IN THE BOX. BLOCKING SHALL BE FIBER BOARD, TYPE CF, GRADE 275, VARIETY SW / DW. SEE FIGURES 1 AND 2 FOR

BLOCKING.

E. INSERT RIFLE WITH BLOCKING IN BOX, BOX INSIDE DIMENSIONS: 32.0 X 9.5 X 3.5; MANUFACTURER'S JOINT SHALL BE SECURE WITH METAL FASTENERS. NOTE: SERIAL NUMBER MUST BE FACING UP. MAGAZINE, SLING, AND TECHNICAL MANUAL SHALL BE INDIVIDUALLY PACKAGED METHOD 31 IN A MIL-DTL-117 CLASS B BAG AND INSERTED INTO BOX.

SEE FIGURE 3.

F. PACKING:

LEVEL A. A QUANTITY OF 50 UNIT CONTAINERS SHALL BE PACKED (PACK FLAT 5 PER LAYER, 10 LAYERS HIGH) IN A MINIMUM SIZE SHIPPING CONTAINER. LEVEL A PACK SHALL BE IN AN ASTM D6251 CONTAINER STYLE A,B,I OR J, TYPE OS, GRADE B. CLOSURE SHALL BE IN ACCORDANCE WITH ASTM D6251.

LEVEL B. PACK SHALL BE IN AN ASTM D5168 STYLE E, WEATHER RESISTANT (WR) CONTAINER. CLOSURE SHALL BE IN ACCORDANCE WITH ASTM D5168. THE LEVEL B PACK CONTAINER SHALL BE SECURED TO AN EXPENDABLE PALLET SIZED TO MATCH THE CONTAINER. THE SAME TYPE OF METALLIC STRAPPING SELECTED TO REINFORCE

THE CONTAINER SHALL BE USED TO SECURE THE CONTAINER TO THE PALLET.

ODD QUANTITIES: FOR QUANTITIES LESS THAN SPECIFIED, ADJUST THE SIZE OF THE SHIPPING CONTAINER TO

OBTAIN MINIMUM CUBE.

ALL NON-MANUFACTURED WOOD USED IN PACKAGING SHALL BE HEAT-TREATED TO A CORE TEMPERATURE OF 56 DEGREES CELSIUS FOR A MINIMUM OF 30 MINUTES. THE BOX/ PALLET MANUFACTURER AND THE MANUFACTURER OF WOOD USED AS INNER PACKAGING OR PALLET GATE/ FILLER ASSEMBLIES SHALL BE AFFILIATED WITH AN INSPECTION AGENCY ACCREDITED BY THE BOARD OF REVIEW OF THE AMERICAN LUMBER STANDARD COMMITTEE.

EACH BOX/ PALLET OR OTHER PACKING MATERIAL SHALL BE MARKED TO SHOW THE CONFORMANCE TO THE INTERNATIONAL PLANT PROTECTION CONVENTION STANDARD. BOXES/ PALLETS AND ANY OTHER WOOD PACKING MATERIAL MADE OF NON-MANUFACTURED WOOD SHALL BE CERTIFIED HEAT-TREATED. THE QUALITY MARK SHALL BE PLACED ON BOTH ENDS OF THE OUTER PACKAGING, BETWEEN THE END CLEATS OR END BATTENS; ON TWO

SIDES OF THE PALLET OR OTHER PACKING MATERIAL.

G. MARKING: MARKING OF UNIT AND EXTERIOR CONTAINERS SHALL BE IN ACCORDANCE WITH MIL-STD 129. PACKING LISTS ARE REQUIRED. SERIAL NUMBER MARKINGS ARE REQUIRED. NOMENCLATURE SHALL NOT BE MARKED ON

THE SHIPPING CONTAINER.

DISTRIBUTION STATEMENT A; APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE IDENT 3. SPI NO.

9390000 CARBINE, 5.56MM, M4 19200 AM9390000

4. NATIONAL STOCK NO. 5. DATE OF DRAWING / SPI

(YYMMDD)

6. REVISION / ERR NO.

1005-01-231-0973 080726 D/L07S3073

17. NOTES / DRAWINGS

DD FORM 2169, JUN 1997 Previous editions are obsolete Page 3 of 5 Pages

BARREL BLOCKING

1. MATERIAL: FIBERBOARD, ASTM D4727; OR A-A-59136

2. IF FIBERBOARD IS USED, DUNNAGE SHALL BE CONSTRUCTED OF AS MANY

THICKNESSES OF FIBERBOARD AS REQUIRED. LAMINATE IN ACCORDANCE

WITH ASTM D4727, OR TAPE IN TWO PLACES WITH ASTM D5330.

DISTRIBUTION STATEMENT A; APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE IDENT 3. SPI NO.

9390000 CARBINE, 5.56MM, M4 19200 AM9390000

4. NATIONAL STOCK NO. 5. DATE OF DRAWING / SPI

(YYMMDD)

6. REVISION / ERR NO.

DD FORM 2169, JUN 1997 Previous editions are obsolete Page 4 of 5 Pages

BUTT STOCK BLOCKING

1. MATERIAL: FIBERBOARD, ASTM D4727; OR A-A-59136

2. IF FIBERBOARD IS USED, DUNNAGE SHALL BE CONSTRUCTED OF AS MANY

THICKNESSES OF FIBERBOARD AS REQUIRED. LAMINATE IN ACCORDANCE

WITH ASTM D4727, OR TAPE IN TWO PLACES WITH ASTM D5330.

DISTRIBUTION STATEMENT A; APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE IDENT 3. SPI NO.

9390000 CARBINE, 5.56MM, M4 19200 AM9390000

4. NATIONAL STOCK NO. 5. DATE OF DRAWING / SPI

(YYMMDD)

DD FORM 2169, JUN 1997 Previous editions are obsolete Page 5 of 5 Pages

DISTRIBUTION STATEMENT A; APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE IDENT 3. SPI NO.

9390000 CARBINE, 5.56MM, M4 19200 AM9390000

4. NATIONAL STOCK NO. 5. DATE OF DRAWING / SPI

(YYMMDD)