SOW - FA481924QA077.pdf

23 May 2024

Statement of Work (SOW)

Inspection Table

325 MUNITIONS SQUADRON PURCHASE

325th Maintenance Group, Tyndall AFB Florida

TABLE OF CONTENTS

Section, Title & Page Number

1.0 DESCRIPTION OF SERVICES

2.0 GENERAL INFORMATION

3.0 DRAWING SPECIFICATION

1.0 DESCRIPTION OF SERVICES

1.1 SCOPE. This project involves manufacture and delivery of four munition maintenance inspection tables.

1.2 EQUIPMENT, MATERIALS, AND LABOR. Contractor shall build Inspection Tables exactly as specified on drawing.

1.3 EQUIPMENT REQUIREMENTS

1.3.1 ‐ Interpret drawing IAW ASME Y14.100 and ASME Y145M‐1994 ‐ Screw threads shall conform to FED‐STD‐H28/2, and be inspected IAW ANSI/ASME B13M, System 21 ‐All parts shall be in the condition specified by the drawings and shall be free from defects such as, but not limited to blemishes, burrs, cavities, pits, voids, corrosion, cracks, dents, distortion, warpage, gouges, scores, nicks, inclusions, laps, porosity slivers, and other foreign matter except as provided on the drawing, Cleaning shall be thorough to remove all dirt, chips, grease, oil, flux chemical deposits, residues, and other foreign matter. The cleaning method and agents used shall not be injurious to any part or to the environment, nor shall any part be contaminated by the cleaning agent.

1.3.2 Contractor may commence on‐site delivery through coordination with the appropriate Points of Contact (aka Government Representatives).

Delivery.

i. Scheduling Delivery. Contractor shall coordinate delivery with the 325 MUNS resource advisor.

2.0 GENERAL INFORMATION

2.1 HOURS OF OPERATION. Hours of operation can start as early as 0700 and end as late as 1600, Monday through Friday. Contractor will coordinate with the Government representative on specific work hours.

3.0 Drawing Specifications

See next page.

ENGINEERING DRAWING LAYOUT D

USED ONNEXT ASSEMBLY

FEB 74

FORMAF

CODE IDENT NO.

CURRENT

.XXX±

.XX±

DECIMALS ANGLESFRACTIONS

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

THIRD ANGLE PROJECTION

PARTS LIST

APPLICATION

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOL

UNLESS OTHERWISE SPECIFIED

QUANITY REQUIRED PER DASH NO.

20075135 20075135

.5°.010 .03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

NOTES:

1. INTERPRET DRAWING IAW ASME Y14.100 AND ASME Y14.5M-1994.

2. REMOVE ALL BURRS AND SHARP EDGES .06 MAX

3. WORKMANSHIP:

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES,

PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT,

CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR

TO THE ENVIRONMENT, NOR SHALL ANY PART BE CONTAMINATED BY THE CLEANING

AGENT.

4. CLEAN PART(S) USING CLEANING METHOD AND AGENTS, WHICH SHALL NOT BE INJURIOUS

TO THE PART(S) OR THE ENVIRONMENT.

5. PERMANENTLY MARK 18894-X20075137-10 IN APPROX AREA SHOWN, IN .12 HIGH

CHARACTERS, IAW MIL-STD-130.

6. WELD IAW ANSI/AWS D1.2-2003.

7. ALL SEALED TUBE ASSEMBLIES SHALL HAVE A .25 DIAMETER WEEP/DRAIN HOLE TO

PERMIT CONDENSATION DRAINAGE.

3 2X

52X

2 SUPPORT TUBE -13 1.00 DIA 6061-T651 ALUM ROUND ASTM-B211 1D4 6

2 STOP PLATE -11 .190 THK 6061-T6 ALUM SHT. ASTM B209 1B3 5

2 END SUPPORT -07 2.00 X 2.00 X .125, 6063-T52 ALUM SQ TUBE , ASTM B-221 1C2 4

2 BRACE -05 2.00 X 2.00 X .125, 6063-T52 ALUM SQ. TUBE ASTM B221 1C3 3

1 CENTER SUPPORT -03 3.00 X 3.00 X .125, 6063-T52 ALUM SQ TUBE ASTM B221 1D3 2

1 BASE -01 2.00 X 3.00 X .125, 6063-T52 ALUM RECT. TUBE ASTM B221 1C5 1

-10 NOMENCLATURE CAGE IDENTIFYING NO. MATERIAL/SPECIFICATION ZN FN

4 2X

6 2X

3 D

3 A

4 C

4 B

3 B

4 A

SEE DETAIL -01

SEE DETAIL -03

SEE DETAIL -05

SEE DETAIL -07

SEE DETAIL -11

SEE DETAIL -13

ENGINEERING DRAWING LAYOUT D1655

FEB 74

FORMAF

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLID EDGE

REV

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

2X.12

2X .12 2X.12

.12

3X .12

2X .12

2X.12

.12 2X.12

2X .12

2.122X

65.88

5.25

20.66

.352X

.622X

.19

.12

.12

.12 2X.12 G

G

65.50

18.472X

O .547

COAXIAL WITHIN O.060

(THRU F/N 2 AND 6)

O .406

TWO HOLES COAXIAL WITHIN O.031

.192X

COAXIAL WITHIN O.060

16.782X

FEB 74

FORMAF

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLID EDGE

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

.12 (STK)

2.00 (STK)

2.00 (STK)

33.55

30° 60°

.19 (STK)

O 1.00 (STK)

4.75

2.38

1.19

1.00

O .406 +.005 -.001

O .547 +.008 -.001

DETAIL -05

DETAIL -11

DETAIL -13

C

B

C

SCALE: 1/1

SCALE: 1/2

SCALE: 1/1

2X .12 X 45v

2.00

FEB 74

FORMAF

CODE IDENT NO.

CURRENT

.XXX±

.XX±

DECIMALS ANGLESFRACTIONS

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

THIRD ANGLE PROJECTION

PARTS LIST

APPLICATION

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOL

UNLESS OTHERWISE SPECIFIED

QUANITY REQUIRED PER DASH NO.

20075136 20075135

.5°.010 .03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES,

PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT,

CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR

5. PERMANENTLY MARK 18894-X20075139 IN APPROX AREA SHOWN, IN .12 HIGH

3 2X

2 SPACER -05 .312 THK 6061-T651 ALUM PLATE ASTM B-209 1C2 3

1 SHIM PLATE -03 .125 THK 6061-T6 ALUM SHEET ASTM B209 1C4 2

1 CENTER SUPPORT -01 2.00 X 3.00 X .125 THK ALUM REC TUBE, 6063-T52 1B3 1

-10 NOMENCLATURE CAGE IDENTIFYING NO. MATERIAL/SPECIFICATION ZN FN

SEE DETAIL -01

SEE DETAIL -03

SEE DETAIL -05

3 C

2 B

3 A

-10 ASSEMBLY

SEE SHEET 2

FORMAF

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLID EDGE

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

20.002X

40.00

1.312X

2.00 (STK)

3.00 (STK)

.12 (STK)

O .547 +.008 -.0012X

2.00

18.502X.182X

6X.12

.12 2X

2.62

3.12

DETAIL -01

40.00

B

-10 ASSEMBLY

SCALE: 1/2

O .547

COAXIAL WITHIN .031

1.13

FORMAF

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLID EDGE

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

.312 (STK)

.12 (STK)

1.50

3.00

1.13

2.50

1.50 7.50

13.50 23.50

29.50 35.50

37.00

1.00

O .506X

O .547 +.008 -.001

2.00

DETAIL -03

DETAIL -05 1 C

C

SCALE: 2/1

SCALE: 1/2

FEB 74

FORMAF

CODE IDENT NO.

CURRENT

.XXX±

.XX±

DECIMALS ANGLESFRACTIONS

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

THIRD ANGLE PROJECTION

APPLICATION

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOL

UNLESS OTHERWISE SPECIFIED

QUANITY REQUIRED PER DASH NO.

20075136 20075135

.5°.010 .03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES,

PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT,

CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR

5. PERMANENTLY MARK 18894-X20075140-10 IN APPROX AREA SHOWN, IN .12 HIGH

1 SPACER -03 2.00 DIA 6061-T6 ALUM ROUND 1B3 2

1 TOP SIDE RAIL -01 2.00 X 4.00 X .125 THK ALUM TUBE 6063-T52 1C3 1

-10 NOMENCLATURE CAGE IDENTIFYING NO. MATERIAL/SPECIFICATION ZN FN

SEE DETAIL -01

SEE DETAIL -03

2 B

2 A

-10 ASSEMBLY

SEE SHEET 2

FORMAF

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLID EDGE

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

DISCLOSURE OF CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.

O 1.015 +.015 -.0012X

O 2.00 (STK) O 1.000

.12 .12

G

-10 ASSEMBLY

DETAIL -01

DETAIL -03

1 C

1 B

2.00 (STK)

4.00 (STK)

.12 (STK)

20.002X

1.312X

SCALE: 1/2

SCALE: 1/1

A

A

SECTION A-A

.12 X 45v

2.00

3.19

40.00

2X .03 X 45v

2X .12 X 45v

3.19

O .531 +.008 -.001

FEB 74

FORMAF

CODE IDENT NO.

CURRENT

.XXX±

.XX±

DECIMALS ANGLESFRACTIONS

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

THIRD ANGLE PROJECTION

PARTS LIST

APPLICATION

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOLI

UNLESS OTHERWISE SPECIFIED

QUANITY REQUIRED PER DASH NO.

20075135

.5°.010 .03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

3. SCREW THREADS SHALL CONFORM TO FED-STD-H28/2, AND BE INSPECTED IAW

ANSI/ASME B1.3M, SYSTEM 21.

4. WORKMANSHIP:

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES,

PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT,

CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR

5. CLEAN PART(S) USING CLEANING METHOD AND AGENTS, WHICH SHALL NOT BE INJURIOUS

6. PERMANENTLY MARK 18894-X20075142-01 IN APPROX AREA SHOWN, IN .12 HIGH

7. MATERIAL: 2024 OR 6061 ALUM RECT. BAR. ASTM-B211, 1.75 X 2.00 X 12.00 LG.

MAY BE PURCHASED FROM: MCMASTER CARR SUPPLY COMPANY,

P.O. BOX 740100, ATLANTA, GA 30374-0100,

PHONE: (404) 346-7000.

PART NO. 89215K349

20075135

-01 LEG EXTENDER

MATERIAL:

FEB 74

FORMAF

CODE IDENT NO.

CURRENT

.XXX±

.XX±

DECIMALS ANGLESFRACTIONS

DIMENSIONS ARE IN INCHES-TOLERANCES ON:

THIRD ANGLE PROJECTION

PARTS LIST

APPLICATION

28 7 6 5 4 3 1

A

B

C

D

A

B

C

D

GENERATED USING SOL

UNLESS OTHERWISE SPECIFIED

QUANITY REQUIRED PER DASH NO.

20075135 20075135

.5°.010 .03

CAD MAINTAINED. CHANGES SHALL ONLY BE

INCORPORATED AT THE DIRECTION OF THE DESIGN

ACTIVITY USING A COMPATIBLE CAD SYSTEM.

REVISIONS

LTR DESCRIPTION DATE APPROVED

DISTRIBUTION STATEMENT C DISTRIBUTION AUTHORIZED TO U.S. GOVERNMENT AGENCIES AND THEIR CONTRACTORS. REASON: ADMINISTRATIVE OR OPERATIONAL USE. DATE: 15 SEPTEMBER 1988. OTHER REQUESTS FOR THIS DOCUMENT SHALL BE REFERRED TO MMHE FOCAL POINT, EGLIN AFB, FL 32542-5000.

WARNING - THIS DOCUMENT CONTAINS TECHNICAL DATA WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE 22, U.S.C., SEC. 2751, ET SEQ.). VIOLATIONS OF THESE EXPORT CONTROL LAWS ARE SUBJECT

TO SEVERE CRIMINAL PENALTIES.

DESTRUCTION NOTICE - FOR UNCLASSIFIED, LIMITED DOCUMENTS, DESTROY BY ANY METHOD THAT WILL PREVENT

ALL PARTS SHALL BE IN THE CONDITION SPECIFIED BY THE DRAWINGS AND SHALL BE

FREE FROM DEFECTS SUCH AS, BUT NOT LIMITED TO, BLEMISHES, BURRS, CAVITIES,

PITS, VOIDS, CORROSION, CRACKS, DENTS, DISTORTION, WARPAGE, GOUGES, SCORES,

NICKS, INCLUSIONS, LAPS, POROSITY, SLIVERS, AND OTHER FOREIGN MATTER. EXCEPT

AS PROVIDED ON THE DRAWING, CLEANING SHALL BE THOROUGH TO REMOVE ALL DIRT,

CHIPS, GREASE, OIL, FLUX CHEMICAL DEPOSITS, RESIDUES, AND OTHER FOREIGN MATTER.

THE CLEANING METHOD AND AGENTS USED SHALL NOT BE INJURIOUS TO ANY PART OR

5. IDENTIFY AS “18894-X20075143-01”, BY BAG, TAG, OR BOX, IAW MIL-STD-130.

6. MATERIAL: STATIC DISSIPATIVE UHMW POLYETHYLENE, COLOR BLACK .50 THK X 2.00

WIDE X 60.00 LONG.

MAY BE PURCHASED FROM MCMASTER CARR SUPPLY COMPANY, P.O. BOX 740100,

ATLANTA, GA 30374-0100, PART NO. 9542K34.

O .205 +.005 -.0014X c.437 X `.25

.50 (STK)

.502X

3.00

.502X

2.00

R .254X

MATERIAL:

2.0002X

1.0002X