SOW Deutz Diesel Engine Assembly 10_20_20.docx
DOCX document 18 KB Posted
- Attached to
- Duetz Diesel Engines Federal contract opportunity
- Solicitation number
- FA481921QA022
About this file
This statement of work outlines requirements for a Deutz diesel engine assembly kit contract. The Air Force seeks a contractor to provide 30 Deutz D2011L04i diesel engine assembly kits for use at Tyndall Air Force Base in Florida. Each kit must include a new Tier 4 Deutz diesel engine rated at 63.7 horsepower, along with starter, alternator, shutdown solenoid, glow plugs, control panel, engine harness, exhaust pipe, cooler guard, throttle components, drain components, timing control unit, slave relay, gauge illumination harness, engine manuals, and oil. The contractor will assemble, test, and quality assure the engines; fill them with oil; and package the loose components. The statement of work also specifies documentation and deliverable requirements.
The related solicitation is for the engine assembly kits described in the statement of work, to be awarded by the Air Force's Air Combat Command.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| COMBO.docx | DOCX document | |
| FY21 Deutz JA_Redacted.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
29 April 2021
Statement of Work CEMIRT Deutz Diesel Engine Assembly Kit Parts and Equipment
1. PURPOSE: The contractor shall furnish all required parts, equipment, material, and labor to provide the following items in accordance with (IAW) all applicable codes, specifications, and industry/federal standards to CEMIRT at Tyndall AFB, Florida.
2. SCOPE
A. Deutz Diesel Engine Assembly Kit – P/N:D2011L04i - Each: 30 The purpose of this section is to detail the work required to fulfill 30 Brand Name Deutz Diesel Engine Assembly Kits. Each assembly kit must include the following items: Deutz Diesel Tier 4 engine (NEW) with EGR valve, rated for 63.7 HP @2600 RPM; P/N: D2011L04i, 24 Volt; EPA NSE Exemption label; OEM Black Paint Finish; 1 Power Take-off (PTO) Package, HSG Size: 4; Clutch Size: 8S (NACD), P/N: 431026AM
2. Starter, 24 Volt, P/N: 4300286 – 1 each
3. Alternator, 24 Volt, P/ N: 103903 – 1 each
4. Shutdown Solenoid, 24 Volt, P/N: 4103822 – 1 each
5. Glow Plugs, 24 Volt, P/N: 1179017 – 2 each
6. LOFA 24 Volt Control Panel with ground pre-heat indication, internal Illumination wire harness and no factory wiring harness P/N: EP250KL7.
Note: The oil pressure gauge must be relocated from the lower left corner to the center top position on the LOFA Panel.
The remaining part numbers are to be supplied by Stauffer Diesel Inc.; 34 Stauffer Lane; Ephrata, PA 17522; (717) 738-2500
7. Engine Harness with USAF Spec Relay Sockets P/ N: 24511 – 1 each
8. Exhaust Pipe P/N: 21998 – 1 each
9. Guard, Cooler P/N: 1732 – 1 each
10. Throttle Lever with Mounting Kit (Speed Control) P/N: 1548 – 1 each
11. Aluminum Vernier Throttle Cable, 75 Inches Long P/N: 58028 – 1 each
12. Truck Valve, Lube Oil Drain P/N: 57267 – 1 each
13. Adapter, Oil Drain P/N: 57268 -1 each
14. Timing Control Unit (Relay) P/N: 4219375 – 1 each
13. Slave Relay, P/N: 4271981 – 1 each
14. Wire Harness, Gauge Illumination, P/N: 801-3305-1 – 1 each (Included within LOFA Panel)
15. MC Engine Mounts, Flex (2 Front/2Rear), P/N: 22000565
B. Vendor will perform the following actions: Completely assembly engine(s) including all the above listed items with the exception of the lifting eyes. Add engine lube oil to engine(s) and test run to perform quality assurance (QA) inspection to verify operation and correct indication on control panel for all engine safety shut down devices e.g., low oil pressure, high engine temperature. Ensure all gauges are functioning properly and calibrated; throttle operates freely with no binding; and D.C. charging system checked. Verify engine preheat system is operational through the preheat controller and indicating properly on the engine control panel. The engine/PTO must be completely assembled and attached to the engine. The following loose items must be packaged with each engine: 24 volt LOFA Control panel and all the requested manuals. The loose items will be verified and inventoried for packaging/completeness.
C. A copy of the QA test report must be included with each engine. Each individual engine will be filled to capacity with diesel multi-viscosity SAE 15W-40 lube oil.
D. Parts Manual, Deutz Diesel P/N: 11192 – 1 each
E. Operators/Instruction Manual, Deutz Diesel P/N: 11193 – 1 each
File details come from the government source that posted it. Updated .