SOO - Guralp Sensor Support.pdf

Statement of Objective (SOO)/Technical Requirements Package (TRP)

Air Force Technical Applications Center (AFTAC)

Guralp Sensor Support

6 Jan 2022

1. SOO/TRP Template for 2GIT Products Purchases Guralp Sensor Support.

2. Purpose Purchase Guralp support equipment to sustain current broadband mission and provide training to Central Repair Facility Airmen.

3. Technical Requirements The contractor shall ensure that all applicable Commercial-Off-The-Shelf (COTS) IA and IA-enabled products comply with AFI 17-130, Air Force Cybersecurity Program Management. All IT hardware, firmware, and software components or products incorporated into DoDIN must comply with evaluation and validation requirements in DoDI 8500.01 and CNSSP-11, National Policy Governing Acquisition of IA Products. Refer to CNSSP No. 11 for the latest process and policy guidance on this subject.

See Ordering Table in Section 4 for specific requirements.

3.1 Special Asset Tagging

The contractor shall provide special asset tags IAW MIL STD-130, DODI 8320.04, Item Unique Identification (IUID) Standards for Tangible Personal Property and DFARS 252.211-7703, Item Identification and Valuation. The current list of accepted unique item identifier types is maintained at http://www.acq.osd.mil/dpap/pdi/uid/uii_types.html. All DoD recognized unique identification equivalents are listed at http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html.

4. Ordering Table

Item Description Qty

ASM-BHO-0279 Vertical Sensor Assy for training 2

ASM-BHO-1280 Horizontal Sensor Assy for training 2

ASM-BHO-1281 Horizontal Sensor Assy for training 2

ASE-S30-0008 Top Unlock/Level Circuit Board 12

ASM-V30-0030 Vertical Lock Motor 6

ASM-V30-0033 Vertical Centre Motor 6

ASM-H30-0028 Horizontal Sensor Lock Motor 12

ASM-H30-0031 Horizontal Sensor Centre Motor 12

CON-WIR-1001 .004 Inch NiCr Springwire 1

CON-WIR-0002 Fine Copper Wire, Smaller size 1

CON-WIR-0003 Fine Copper Wire, Larger size 1

CAS-BHO-0001 Mass Lock Internal Wiring Loom 10

CAS-BHO-0002 Centering Motor Loom 10

CAS-BHO-0004 N/S Wiring Loom 10 http://static.e-publishing.af.mil/production/1/saf_cio_a6/publication/afi17-130/afi33-200.pdf http://www.esd.whs.mil/Portals/54/Documents/DD/issuances/dodi/850001_2014.pdf http://www.acq.osd.mil/dpap/pdi/uid/uii_types.html http://www.acq.osd.mil/dpap/pdi/uid/iuid_equivalents.html

CAS-BHO-0005 Vertical Wiring Loom 10

ELC-CRP-14BL HE 14 Crimp Terminal 182734-2 (Housing number ELC-HEH-

06HE) 300

ELC-HEC-03SR 3 Pin R/A Connector 2.54 mm Pitch HE14 Series 10

ELC-HEC-04SR 4 Way Single Row Connector R/A 10

ELC-HEC-12DR 12 Way Double Row Connector R/A (281742-6) 20

ELC-MLX-03CH 51021-0300 - 3W 1.25mm Crimp Housing 20

ELC-MLX-06CH 6 Way Crimp Housing 10

ELC-PCL-0048 4.8mm P/Clip 5

MEC-030-0004 Spring Clamp 10

MEC-030-0157 Base For 3 1/2" Stack Set 5

MEC-030-0160 CMG-3 PCB Support Horizontal 20

MEC-030-0161 CMG-3 PCB Support Vertical 10

MEC-GEN-2020 Instrument Foot for Type 'A' Borehole 5

MEC-BHO-0069 CMG3 Vertical Bulkhead For 3 1/2' Stacking Set 10

MEC-BHO-0071 Electronics Carrier for CMG-3GHO and 40T s/c 10

MEC-HEX-12MF M3 x 12 Male/Female Hex Spacer 5mm Probe 50

MEC-V30-0021 CMG-3 Vertical Spring 10

MEC-V30-0156 Extra Weight Mass Borehole 5

NUT-SFL-0030 M3 Full Stainless Steel Nut 50

NUT-SNL-0030 M3 Nylock Stainless Steel Nut 50

SCR-S06-P030 M3 x 6 Pan Head Slotted Stainless Steel Screw 50

SCR-S06-P030 M2 x 6 Socket Cap Head Stainless Steel Screw 20

SCR-S06-S020 M3 X 6 Socket Cap Head Stainless Steel Screw 50

SCR-S12-P030 M3 x 12 Pan Head Stainless Steel Screw 50

SCR-S12-S030 M3 x 12 Socket Cap Head Stainless Steel Screw 25

ASM-BHO-1014 Bishops Hat Adapter 5

MEC-030-0385 Dummy Pivot 5

Shipping 1

Packaging 1

5. Technical Contractual Requirements

5.1 Technical Refresh

In order to ensure new design enhancements and technological updates or advances, the contractor shall offer, under this DO, hardware and software components available to the contractor's commercial customers. Furthermore, the contractor shall make available any commercially available updates to the hardware and software provided under this DO. If such updates are available to other customers without charge, then they shall also be made available to the Government without additional charge. The contractor will ship these updates to existing customers who have acquired the hardware/software being updated under thi20s DO. Vendor commercial product offerings shall include “state of the art” technology, i.e., the most current proven level of development available in each product category.

5.2 Trade Agreement Act (TAA)

All proposed products must be compliant with the Trade Agreements Act of 1979 (TAA) and related clauses in Section I of this contract. In accordance with DFARS 252.225- 7021, the Trade Agreements Certificate at DFARS 252.225-7020 shall be provided for each end item defined and specified in a solicitation that exceeds the TAA threshold subject to the waivers and exceptions provided in FAR 25.4, and DFARS 225.4 offered in response to any RFQ issued under this contract. Please note that Federal Acquisition Regulation (FAR) paragraph 25.103(e) includes an exemption from the Buy American Act (BAA) for acquisition of information technology that is commercial items.

5.3 Authorized Resellers

The contractor may be an authorized reseller of new and refurbished/remanufactured equipment for OEMs proposed under this DO. The contractor may also procure directly from the OEM or utilize other legitimate distribution channels to provide the required products in accordance with the OEM’s policies on reselling. Any contractor’s channel relationships with their OEM partners (gold, silver, etc.) will be represented in the best pricing offered. If the contractor is not an OEM reseller, the contractor shall clearly identify this on the submitted proposal and list the OEM resell partner’s registered relationship with the OEM. DOs may restrict the use of authorized resellers, specific OEMs, or identify required OEMs. The contractor shall ensure all products are genuine and eligible for any OEM warranties, maintenance agreements and licensing as offered. Genuine products are those products the OEM, by their policy, considers not “secondary”, destroyed, stolen or scrapped.

5.4 Remanufactured/Refurbished Products

Any product offering that is remanufactured or refurbished shall be clearly identified as such by the contractor on the submitted proposal. Remanufactured products shall have the OEM or factory certification, if available, for that product. Remanufactured and refurbished products shall be certified according to the standards set forth in the policy of the OEM.

5.5 Items on Backorder

In their response to a Request for Quote (RFQ), the contractor shall provide notification, if applicable, that a particular item is on backorder, the expected lead-time to fulfill the order, etc.

It shall be implicit that a response to an RFQ with no items identified on backorder is a declaration that the items are available at the time of quote submission.

5.6 Warranty

The contractor shall provide any OEM pass through warranty and standard commercial warranties applicable to the products being purchased at no cost. This shall apply to new, refurbished and remanufactured equipment.

5.7 Hardware and Associated Software and Peripherals

All hardware delivered under this DO shall include associated software, documentation and associated peripherals required for operations (such as controllers, connectors, cables, drivers, adapters, etc.) as provided by the OEM. This is true only if the applicable OEM provides such items with the product itself.

5.8 Software

For all software that is outside of hardware and purchased independently, the contractor shall provide the software license registered to the customer’s organization.

5.9 Safeguarding Classified Information

The contractor shall transmit and deliver classified material/reports IAW the National Industrial Security Program Operations Manual (NISPOM) and the National Industrial Security Program Operating Manual (DoD 5220.22-M). These requirements shall be accomplished as specified in the Delivery Order. All Classified Contracts must have at a minimum, the Clause 52.204-2 Security Requirement, incorporated into the contract.

5.10 Installation

The only time that installation services can be procured is when the services and cost are included in the price of the product as sold commercially. In the rare instances where installation services are required/offered, the contractor shall provide installation support related to the applicable products(s) as defined in the DO. In those instances, the DD Form

254 (DEPARTMENT OF DEFENSE CONTRACT SECURITY CLASSIFICATION

SPECIFICATION) requirements will be addressed in the individual DO and only at the security level necessary.

5.11 Customer Support

The prime contractor shall provide 24x7 live telephone support during the warranty period to assist in isolating, identifying, and repairing software and hardware failures, or to act as liaison with the manufacturer in the event that the customer requires assistance in contacting or dealing with the manufacturer.

5.12 Product Maintenance

The contractor shall provide associated maintenance and upgrades to include spares/parts and emergency support worldwide, during the warranty period.

6. Delivery Requirements

6.1 Timeframes

The contractor shall adhere to the following Product Delivery Capability requirements when providing products under this DO. The contractor shall deliver the quantities of products to meet ordinary as well as fluctuating (war-time, Terrorist Tempo, Ops Tempo) government requirements in accordance with prescribed delivery schedules stipulated in individual DOs.

Delivery of products will be to CONUS, OCONUS, and remote locations as identified below.

For AOR’s and/or remote sites that do not permit commercial deliveries, the vendor’s delivery capabilities must be in accordance with AFI 24-203, Preparation and Movement of Air Force Cargo, 13 April 2007. Additional delivery terms or schedules, such as ship-in-place, expedited shipping or shipping to APO/FPO addresses, shall be negotiated between the Contractor and the Ordering Contracting Officer (OCO).

Definitions: CONUS: The 48 contiguous states, Alaska, Hawaii, and the District of Columbia.

OCONUS: Germany, Italy, Japan, Korea, Belgium, Turkey, Puerto Rico, United Kingdom, and the Netherlands. Remote OCONUS: those locations that are not listed under CONUS or

Named OCONUS.

The following figure sets forth the maximum performance parameters for deliveries:

Timeframe CONUS OCONUS Remote OCONUS

Routine NLT 30 calendar days NLT 45 calendar days NLT 45 calendar days

Critical NLT 3 calendar days NLT 5 calendar days NLT 10 calendar days

Emergency/War Tempo

Within 24 hours Within 48 hours Within 72 hours

6.2 DO Order Shipping Date

This DO requires a routine delivery.

6.3 Delivery Delays

Contractors are required to meet the timeframes as stated in section 6.1 unless Department of Commerce approval and/or review activities prevent the contractor from meeting these timeframes. In the event that the contractor determines they are unable to achieve the stated timeframes, the contractor shall notify the Contracting Officer within two (2) business days of such determination, or immediately upon such determination if operating under the Emergency/War Tempo timelines.

Shipping Information

All products shall be shipped to:

SSgt Matthew Ignacek

709 SPTS/MSM

AFTAC Bldg. 10989 1020 S. Patrick Drive Patrick AFB FL 32925 Doug.da.e@us.af.mil

COM: 321-494-0692

DSN: 854-0692

Inspection/Acceptance: The following Government officials are responsible for receiving the products and performing inspection:

Primary POC: John Corcoran, 709 SPTS/MSMD, 321-494-3667 Alternate POC: Alan Yerington, 709 SPTS/MSMD, 321-494-9431