SeeByte_ SOW.pdf

Statement of Work

OMAN DT-P-LAW / Site Assessment Technical Support Visit and SeeByte SeeTrack OEM Training

1.0 Description of Services

1.1 Scope

The Naval Surface Warfare Center, Indian Head Division (NSWC IHD) has a requirement to provide Technical Support and Training in support of SeeByte SeeTrack Software for FMS Case DT-P-LAW for Oman.

1.2 Requirement

The Contractor shall provide all staffing and materials to provide Technical Support to install, integrate and test SeeByte SeeTrack Post Mission Analysis (PMA) Software and to train EOD personnel to utilize and maintain SeeByte SeeTrack Post Mission Analysis (PMA) with NEPTUNE Software.

- Original Equipment Manufacturer (OEM) Technical Assistance: In-country Site Assessment Technical Support Visit: One (1) Field Technician, up to five (5) days to install, integrate and test SeeByte SeeTrack Post Mission Analysis (PMA) Software, anticipate visits will occur in Oman near Muscat, (Qty. 1)

- SeeByte SeeTrack Post Mission Analysis (PMA) with NEPTUNE Software OEM Training:

Minimum one (1) instructor, up to ten (10) days duration for up to five (5) trainees at the benefitting country facility (anticipate training will be conducted in Oman, near Muscat).

Training includes basic and advance operations, course will include all required training guides and associated materials in English, (Qty. 1)

Benefi ng Country Responsibility for training:

1) suitable vessel, vessel operator, safety equipment (life jackets, etc.), classroom facility, and REMUS vehicle to accommodate training course. The classroom facility should have adequate and safe power supplies and desks.

2) personnel to assist in the transporta on/se ng up and taking down of the computer equipment under instructor direc on.

3) A REMUS AUV with no known defects and personnel to transport AUV and/or transporta on case to and from the vessel.

5) A full safety brief prior to leaving pier.

The Benefi ng Country will iden fy trained and experienced personnel with an English Comprehension Level (ECL) score of at least seventy-five (75) percent to receive the training or will provide interpreters.

All training will be conducted in English.

2.0 Training Facilities

The training facilities will be located in Oman. The Contractor shall provide facility requirements needed for the training (e.g., safety equipment, vessels, operators, AV equipment, IT equipment, classroom requirements, etc.) no later than 120 days prior to the training start date. The Government will provide the facility location/address to the Contractor no later than 90 days prior to the training start date.

3.0 Training Execution

3.1 Period of Performance

The Contractor shall be available to conduct training within six (6) months of equipment being accepted.

The Contractor shall contact the Government and begin coordination of all arrangements no later than 90 days prior to training start date. The Contractor shall also notify Government upon completion of training. Period of performance shall not exceed one (1) year.

3.2 Place of Performance

Training shall be performed in Oman.

4.0 Travel

The Contractor shall be required to travel in performance of this contract. All travel shall be conducted in accordance with the Joint Federal Travel Regulations/Federal Travel Regulations (JFTR/FTR).

The Contractor shall be responsible for completing any training requirements and Electronic Country Clearance (ECC) messages for OCONUS travel, as well as obtaining passports and visas. The NSWC IHD Foreign Military Sales (FMS) program office will assist in coordinating these requirements for the Contractor whenever possible.

5.0 Physical Security

The Contractor shall be responsible for safeguarding all Government information or property provided for Contractor use. At the close of each work period, all Government information, facilities, equipment, and materials shall be secured at the end of each day.

5.1 Technology Transfer IAW International Traffic in Arms Regulation (ITAR)

The Contractor is responsible for obtaining all necessary approvals and clearances to allow the shipment of training materials to the customer country by either claiming an FMS exemption under the auspices of the applicable Letter of Offer and Acceptance (LOA), in accordance with the ITAR, Part 126, General Policies and Provisions, Sub-Part 126.6, and the FMS program, or with an approved Technical Assistance Agreement (TAA), in accordance with the applicable ITAR, Part 124, Agreements, Off-Shore Procurement and Other Defense Services, Sub-Part 124.1, Manufacturing License Agreements and TAA through the

U.S. Department of State, Directorate of Defense Trade Controls. Also, regarding TAAs reference ITAR, Sub-Part 124.2, Exemptions for Training and Military Services.

The Contractor shall ensure either of these approaches is successfully completed prior to training initiation.

6.0 Deliverables

6.1 Status Report

Within thirty (30) days of completion of training, the Contractor shall provide a report (CDRL A001), in Contractor format, to NSWC IHD describing the following services:

o Training attendees the names/ranks of International Military Students (IMSs) trained o Detail any training issues and unexpected / (or) anticipated delays in training detailed reason(s) for the delays/issues detailed resolution(s) for deviations or delays o Provide any training recommendations for future courses o Provide complete document status of any action items and/or taskers and current status.

6.2 Training Materials

Five (5) copies of the training materials (CDRL A002) in the English language to be provided (one copy each) to students no later than the first day of training.

6.3 Training Facility Requirements:

Facility requirements for the training to be provided no later than 120 days prior to the training start date (CDRL A003).

7.0 Point of Contact Information

NAVEODTECHDIV DODACC: N42794,

Naval Surface Warfare Center Indian Head Division (NSWC IHD) Stump Neck Annex 2008 Stump Neck Rd Bldg. 2195 D26 Receiving (Prior to 2pm M-F) Indian Head, MD 20640

Government Points of Contact (POC):

Shannon Idol Foreign Military Sales (FMS) Technical Project Manager / D25 shannon.n.idol.civ@us.navy.mil (O): 301-744-5746 (M): 240-585-1765

Enrique Garcia Material Management – D26 enrique.l.garcia.civ@us.navy.mil

(O): 301-744-4024