SE11791_-_Attachment_6_-_Equipment_Specs__Caged_.pdf

CITY AND COUNTY OF SAN FRANCISCO Bid# 0000011791 Req# 0000361759

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

SECTION 1 - GENERAL EQUIPMENT SPECIFICATIONS: 1

SPECIFICATION OUTLINE: 3

The following specifications for a Police Pursuit Rated PPV AWD SUV Marked White Caged 4 Patrol Unit is divided into three complete sections. The first section outlines the overall 5 specification requirement. The second details the chassis portion of the Police Pursuit Vehicle. 6 The third section refers mostly to the police upfitting to be mounted onto the Police Pursuit 7 Vehicle chassis. The vehicle shall be delivered complete with all equipment and accessories 8 necessary for safe and efficient operation, ready for immediate job site operation within the City 9 and County of San Francisco. The Police Pursuit Vehicle shall comply with the manufacturer’s 10 current model Police Pursuit Vehicle, with additions and deletions as contained herein. 11

INTENDED USE: 13

The unit proposed by bidders shall be configured to meet or exceed the following intended usage 14 of said unit. The unit described in specifications is intended to provide a pursuit rated vehicle for 15 sworn staff to safely and efficiently perform general law enforcement duties. It is the responsibility 16 of the bidder to review and scrutinize all aspects of the configuration of this unit including, but 17 not limited to, engine size, transmission, axle weight rating, gear ratio, frame size, and 18 suspension types being specified in this document. If necessary, the bidder shall recommend 19 adjustments to the written specification so that the unit’s subsystems are adequate enough for 20 this chassis to operate on a daily basis, fully loaded with all components, fuel and standard 21 unmounted necessary tools needed for the unit’s daily tasks. This shall be accomplished without 22 increasing maintenance costs, stressing the frame, or adding any unnecessary and/or abnormal 23 wear to any other components of the unit, off or on-road throughout the City of San Francisco. 24 It is the responsibility of the successful bidder to ensure this unit will comply or exceed 25 compliance to all on-road and off-road safety and emissions standards set forth by the City of 26 San Francisco, State of California, and the Federal Government. 27

MANUFACTURING, MATERIAL AND DESIGN PRACTICES: 29

It is intended that the manufacturer, in the selection of components, will use material and design 30 practices that are the best available in the industry for the type of operating conditions to which 31 the unit(s) will be subjected. All parts, equipment and accessories shall conform in strength, 32 quality of material and workmanship to recognized industry standards. 33

HEAVY DUTY TERMINOLOGY DEFINED: 35

The term “heavy duty” as used in these specifications shall mean that the item to which the term 36 is applied shall exceed the usual quantity, quality or capacity supplied with standard production 37 unit(s) and it shall be able to withstand unusual strain, exposure, temperature, wear, and use. 38

ALTERNATES: 40

Potential variances of a specific manufacturer may require variances in the design to some 41 degree. Therefore, bidders shall clearly and completely outline all areas needing such 42

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

modifications. When the name of a manufacturer, brand or make, with or without model number, 43 is used in describing any item in this specification, bids for similar articles will be considered 44 unless otherwise stated. Bidders may also propose items of equivalent features or 45 manufacturer’s updated part or part number. Purchasing shall be the sole judge as to whether 46 such alternate articles are acceptable. Unless bidder states to the contrary, articles offered will 47 be assumed to be the specific article named in this specification. If not offering the specific article 48 named, bidder should enclose full information, specifications and descriptive data on items 49 offered with its bid. Purchasing reserves, the right to permit deviations from the specifications if 50 any article offered is substantially in accord with Purchasing’s specifications and is deemed by 51 Purchasing to be of as good quality and as fully satisfactory for its intended use. Bidder is 52 responsible for identifying any deviations from Purchasing’s specifications. Bidders should not 53 assume an alternate offered is an approved equal. The City will evaluate the alternate and inform 54 the bidder if the alternate is acceptable. Purchasing must approve all alternates. 55

GENERALITIES: 57

To allow for manufacturers’ specific designs, and ensure a level of competitiveness, we have 58 left certain areas of our specifications general by design. In such cases, the items being referred 59 to may be general but adherence to the requested end product and/or result must be met. This 60 is especially important in areas where critical dimensions, capacities, grades of steel, etc. are 61 specified. In the cases where the word “SHALL” is used, no substitution will be allowed. 62

MANUFACTURERS SPECIFICATION: 64

Complete manufacturer’s specification, published literature, and photos or illustrations of unit 65 proposed should be furnished with bid. Only new models in current production which are 66 catalogued by the manufacturer and for which printed literature and specifications are available 67 will be accepted. Bidders should prepare and submit their own proposals addressing each 68 section, item or component of these specifications indicating full compliance without exception 69 or explaining in detail any exception, deviation or non-compliance. Bidders should not simply 70 submit a copy of a manufacturer’s specifications if they differ from these specifications, nor 71 should they submit copies of manufacturer or third-party quotations as a response to the City’s 72 bid solicitation. 73

MANUFACTURERS STANDARD EQUIPMENT: 75

All equipment and components listed as standard by the manufacturer for model quoted shall 76 be furnished whether or not such items are detailed herein, e.g., special wrenches, tool kits, etc. 77 Optional equipment as necessary to meet the following requirements of this specification shall 78 also be supplied. Should the requirements as specified not comply, the manufacturer is required 79 to re-figure and revise the specifications to meet all laws, rules and regulations where it applies 80 to items such as the ratings of axles, tires, rims, brakes, batteries, cooling capacity, etc. and the 81 City is to be notified thereof. 82

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

APPLICABLE DOCUMENTS AND CERTIFICATIONS: 84

Specifications on the following pages are written with the intent to comply with all applicable 85 safety systems, documents, and certifications, but the final responsibility to comply shall rest 86 with the vendor and not the City and County of San Francisco. The successful bidder shall 87 adhere to the standards set forth by the following agencies if applicable: 88

Federal Motor Vehicles Safety Standard, Department of Transportation (FMVSS) 90 State of California Motor Vehicle Code (CMVC) 91 State of California General Industrial Safety Orders 92 State of California Health and Safety Code, Motor Vehicle Pollution Control 93 California Occupational Safety and Health Act (OSHA) 94 National Electrical Code (NEC) 95 Environmental protection agency (EPA) 96 California Air Resource Board (CARB) 97 Society of Automotive Engineering Standards (SAE) 98 American Society of Mechanical Engineers (ASME) 99 American National Safety Institute (ANSI) 100 Any emergency warning light provided and/or installed for the City and County of San 101

Francisco shall meet the State vehicle code, Title 13 for the appropriate application. 102 The vendor shall provide a copy of the manufacturer's certification of the California Code 103 of Regulations, Title 13, "Motor Vehicles" rules and regulations if requested by the City 104 and County of San Francisco. 105

An SDS (Safety Data Sheet) for all fluids used shall be included with the delivery of the 106 equipment. 107

Underwriters Laboratories (UL) 108

ROPS 109

FOPS 110

OPS 111

DEMONSTRATIONS: 113

The City reserves the option to request, and the bidder shall agree to provide, an “on the job” 114 demonstration and evaluation for the City’s Fleet Management personnel of current production 115 models before acceptance of contract in the event the City is not familiar with the performance 116 of the unit offered. If requested by the City, a demonstrator unit shall be made available prior to 117 award and provided at no additional cost to the City. Time required for such evaluation shall be 118 as determined by the City. In addition, manufacturer may be asked to supply current user’s list 119 of similar units of the size, class and type of the unit offered, which may have been delivered in 120 California. The right is reserved to determine whether substitutions or deviations are within the 121 intent of specifications and will reasonably meet the service requirements of the using 122 Department. 123

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

SERVICE FACILITIES: 125

Awarded vendor to operate or have access to a service facility capable of performing most 126 repairs associated with the equipment they represent. This facility shall be located within 125 127 miles of San Francisco and be stocked with common replacement and high wear parts, as may 128 be designated by the equipment manufacturer, and approved by the City. Alternatively, vendor 129 shall have the ability to have repair persons on site with replacement parts to perform equipment 130 repairs. Any costs incurred for mobile repairs will not be the responsibility of the City while the 131 vehicle remains under warranty. Vendor shall also provide towing to this service facility free of 132 charge if needed while unit is under warranty. We also reserve the right to determine the 133 capability of the supplier’s service facility to adequately service and/or repair the equipment. 134

PRE-CONSTRUCTION REQUIREMENT: 136

The successful bidder shall be required to schedule and attend a pre-construction meeting with 137 the initiators of these specifications and/or designated City representative(s) within 30 calendar 138 days prior to the start of any construction. Weekly update photographs (digital format) may be 139 required of the vendor if requested. The purpose is to ensure the proper interpretation of the 140 City’s written specifications to foster an accurate building of the vehicle/unit. Successful bidder 141 shall alone be responsible for correcting all improper interpretations at no cost to the City due to 142 the failure to schedule meeting(s). If necessary, the vendor may also be required to coordinate 143 any additional meetings prior to the installation of equipment, painting, etc. The location of these 144 meetings shall be either in person at a designated site or conducted via a video conferencing 145 platform. The department representative and specification writers must be notified to schedule 146 the meetings and will provide any necessary information and instructions. A CAD, Solid Work 3-147 D, or conceptual drawing shall be submitted at or before this pre-construction meeting. Drawings 148 are to show streetside, curbside, rear, front and interior views and be in electronic format, 149 accompanied by a vehicle weight study. 150 Specification writers contact information: 152 Jeff Cannuli at (415) 305-8717 153 Jeff.cannuli@sfgov.org 154 or 155 David Chau at (415) 305-4623 156 David.h.chau@sfgov.org 157

CONTRACT AMENDMENT: 159

Any changes made to the specifications after the order is issued shall be approved by the 160 purchaser, the department representative, and the specification writers prior to the incorporation 161 of the changes. Any work performed prior to the City’s issuance of a written amendment to the 162 order will be done at the risk of the vendor with the possibility of delayed acceptance and 163 payment of the unit. 164

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

OPERATIONAL NOISE REQUIREMENT: 166

Noise level shall be in conformance with standards established by Local, State and Federal 167 Agencies. City personnel for noise requirements may test each unit delivered before the unit is 168 accepted. 169

HYDRAULIC SYSTEM REQUIREMENTS: 171

All hoses shall have adequate protective covers wherever there is a possibility of contact with 172 any other components. Separators shall be used where applicable. No tape or adhesive 173 fasteners shall be accepted. All hoses, and pipes shall be routed to be clear of all heat sources 174 and shall be protected from any present or potential source of snags, abrasions or sharp edges. 175 All hydraulic hoses, fittings, valves, and piping shall be manufactured specifically for high-176 pressure hydraulic systems and the specific application they are installed in. All hydraulic 177 lines/hoses where applicable shall have “quick connect,” full face “non-drip” type connectors that 178 shall be capable of being connected and disconnected without the use of tools. Hose assemblies 179 shall be supported with clamps or strap supports at regular intervals. Spacing between supports 180 shall not exceed 18 inches, unless otherwise specified by hose diameter, motion, or 181 manufacturer recommendations. Shall provide additional supports near bends, fittings, and 182 areas subject to vibration or abrasion. Clamps shall not damage the hose cover, must allow 183 proper motion and bend radius, and must prevent contact with moving parts or sharp edges. 184

ELECTRICAL REQUIREMENTS: 186

It shall be the responsibility of the successful bidder to communicate with the manufacturer of all 187 the electrical accessories and equipment being outfitted on the unit so that the appropriate 188 multiplexing system, wiring, connectors, switches, control panels, and circuit breakers can be 189 determined. Any aftermarket lighting or alarms connected to a vehicle’s electrical system or body 190 control module shall be done so through a relay. Crimped wiring connections shall comply with 191 applicable SAE standards, including SAE J163, J1127, and J1128. Connections shall use 192 properly rated terminals and tooling, with conductors tinned where specified. Each crimped 193 connection shall be covered with adhesive-lined heat-shrink tubing to provide a moisture-194 resistant environmental seal. 195 Lighting and auxiliary equipment grounding shall comply with SAE J1908 and use a dedicated 197 ground return conductor(s). Chassis-grounding shall not be permitted for these circuits unless 198 specifically approved by the vehicle and component manufacturer(s). All upfit wiring shall be 199 protected by split-corrugated, UV-resistant loom secured at no more than 10 inches between 200 points, routed away from any heat sources and possible snags, and protected by labeled fuses 201 in easy to access areas of the vehicle. If any wiring is routed through any tool compartment or 202 canopy, these wires shall be enclosed in steel or heavy-duty looming. All high voltage electrical 203 shall be routed through armored weatherproof conduit and properly labeled. 204 The upfitter shall install a Deutsch or approved equal connector for each component mounted 206 on the exterior of the vehicle. All exterior components shall be terminated using weather-207

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

resistant connectors compatible with existing harness systems. Connectors shall allow easy 208 removal and replacement of individual components without cutting or splicing wiring. These 209 connectors shall be located in an accessible position that is protected from road debris and 210 potential impact or fall hazards. 211 NOTE: The use of scotch lock style splice connectors or any other type of wire piercing 212 connectors shall not be accepted in any application. 213

SWITCHES/ LABELS: 215

All external toggle and push button switches shall be marine type with additional rubber boots. 216 All controls, warning gauges and valves shall be marked as to function with stamped or engraved 217 stainless steel, aluminum, and/or UV and weather-resistant acrylic plastic labels. These labels 218 are to be attached by aluminum and/or stainless-steel rivets. 219

WELDING: 221

All welding shall be continuous where applicable and performed in accordance with the latest 222 American Welding Society standards, including AWS D1.1, D1.2, and D1.3 as applicable to the 223 materials used. Welders and procedures shall be qualified to the corresponding AWS code. 224 Welds shall be full-penetration, uniform, and free from defects. All welds shall be visually 225 inspected and, when required, tested using approved nondestructive methods. Workmanship 226 shall meet or exceed AWS quality assurance requirements and these specifications. 227

FASTENERS: 229

All fasteners shall be Grade 5 or higher, with Grade 8 used where required for structural or high-230 stress applications. Fasteners shall be corrosion-resistant and equipped with locking nuts, 231 washers, or thread-locking compound as appropriate. Any fasteners exposed to moisture or 232 corrosive environments shall be treated or coated with an approved anti-corrosion compound. 233

INSPECTION TRIPS 235

If upfitting of the chassis is taking place in a facility that is over 125 miles from San Francisco, 236 the bid price shall include airfare, ground transportation, meals and lodging for one (1) factory 237 inspection trip(s) for two (2) City representatives. Airfare shall include one (1) checked bag per 238 City representative. If flight duration is over 125 minutes, economy plus or equal class seating 239 shall be provided. Flight must be the most direct, shortest duration, non-stop, if available, with a 240 maximum of one (1) connection and have assigned seating. Seat choice to be selected by City 241 representatives. Departure and arrival to be during normal business hours. The inspection trips 242 shall be scheduled at times mutually agreed upon between the awarded bidder and the City 243 representatives and should be for a minimum of two (2) nights. Meals and lodging rate shall 244 comply with the current Federal Per Diem Rates for the Continental U.S.A. The awarded vendor 245 shall be responsible for covering all associated per diem rates for the full three-day period, 246 including meals, lodging, transportation, and incidental expenses as outlined in the contract or 247 agreement terms. 248

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

The rates are available from the following website: 250 https://www.gsa.gov/travel/plan-book/per-diem-rates 252 This inspection trip will be the final factory (pre-delivery) inspection of the completed vehicle, 254 completely finished and ready for delivery. Workmanship and finish will be inspected, and the 255 vehicle will be road tested and equipment operated before final delivery. If the inspection 256 discloses any deviation from the specifications, the discrepancies, if minor, can be corrected 257 while City inspectors remain at the plant. If the problem is not readily correctable, the inspectors 258 shall have the option to return for another inspection at a mutually agreed time at the expense 259 of the awarded bidder. 260

PRE-DELIVERY INSPECTION TRIP: 262

The awarded vendor shall arrange a pre-delivery inspection trip if within 125 miles of the City of 263 San Francisco to view a completely finished and ready for delivery unit. Workmanship and 264 finishing will be inspected, the vehicle will be road tested, and equipment operated before final 265 delivery. If the inspection discloses any deviation from the specifications, the discrepancies, if 266 minor, can be corrected while City inspectors remain at the vendor’s site. If the problem is not 267 readily correctable, the inspectors can return for inspection at a mutually agreed time. Failure to 268 arrange this inspection trip before delivery of vehicle may result in vehicle not being accepted at 269 time of delivery. 270

DELIVERY SCHEDULE: 272

Due to the fabrication design required on this unit, we understand the potential for manufacturing 273 company build schedule delays. For this unit we are setting the delivery schedule at 180 calendar 274 days. This unit should be delivered and be ready for service within the stated time range. If a 275 unit being bid meets all other requirements of the specification, but cannot meet the specified 276 time allotted for delivery, this discrepancy shall be stated. 277

MANUFACTURER RECALLS: 279

All known open recalls issued by manufacturers or the National Highway Traffic Safety 280 Administration (“NHTSA”) must be resolved prior to delivery. In accordance with the Federal 281 Georgia Fair Business Practices Act, Motor Vehicle Safety Act & National Traffic and Motor 282 Vehicle Safety Act, dealerships are prohibited from selling such vehicles until the appropriate 283 repair is complete. 284

ELECTRONIC MANUALS: 286

The following manuals shall be included and be specifically written for the unit being purchased. 287 It shall not to be a generic manual for a multitude of different units: 288

Two (2) operator’s manuals, in print form for each delivered unit. 289 Operators’ manuals for each installed component. 290

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

One (1) complete set of professional grade, OEM level, repair manuals that include291 maintenance, electrical diagrams, electronic and hydraulic diagnostic manuals and292 diagrams in print form.293

Note: The above-mentioned is not for each individual unit procured but for the entire bid 294 purchase. 295

One (1) parts manual with part numbers(USB flash drive is preferred).296 _____Manuals shall be provided before or at the time of delivery of the unit. 297

DOCUMENTATION: 299

_____A weight that accounts for the full payload shall be submitted with bids for any road-worthy 300 vehicle that is modified from the original manufacturer’s standard configuration. 301 _____One (1) set of conceptual CAD drawings for any road-worthy vehicle that is modified from 302 the original manufacturer’s standard configuration shall be submitted at the time of pre-303 construction meeting. Drawings to include right, left, front, rear, and overhead views of 304 interior and exterior. 305

_____After completion of the unit(s), the successful bidder shall provide a weight certificate. To 306 be furnished at time of delivery. 307

_____A certification of compliance with all applicable U.S. Department of Transportation (DOT) 308 and Federal Motor Vehicle Safety Standards (FMVSS) for the completed vehicle shall be 309 provided by the contractor at the time of delivery. 310

_____Successful bidder shall furnish chassis, engine and transmission data plate information to 311 include serial numbers, HP rating, DOB, emissions information, etc. Information is to be 312 placed in an Excel file in birth certificate format that will be provided by City. Pictures of 313 all data plates are to be placed on cloud drive, flash drive, emailed to Central Shops, or 314 delivered with the unit. 315

BIDDER’S COMPLIANCE AND EXCEPTIONS: 317

All exceptions shall be stated no matter how seemingly minor. Bidders shall indicate 318 compliance with each section and line item specifications as required in the line spaces 319 provided by marking with a “Y” for yes. If the bidder is offering an alternate of equal or 320 superior status to the line item specification, bidder will indicate by marking with an “E” 321 for exception on each line item. The bidder must then reference each item exception and 322 explain the exception taken and the proposed alternate on the Bid Exception Sheets. 323

**Bids which do not include confirmation of each section and line item as required will be 325 deemed to take exception to such bid requirements, which may result in the bid being 326 deemed non-responsive. If exceptions are taken, the Bid Exception Sheets must be 327 returned with the submitted bids. 328

IMPORTANT: If a single vendor is submitting multiple bids, the vendor shall submit a 330 completed set of specs for each individual bid. Multiple bids that are submitted as one 331 bid package will not be acceptable. 332

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

SECTION 2 - CHASSIS: 334

The Police Pursuit Vehicle to be furnished under these specifications shall be a basic fleet model 335 and be listed as the manufacturer’s current model. The vehicle shall comply with standard 336 specifications and be delivered with standard equipment for the model offered with exceptions 337 and additions as contained herein. This vehicle shall be new and unused. This vehicle is to 338 perform operations in all weather conditions on a multitude of varying terrain and conditions. 339 Special attention to major components and/or specified critical capacities is mandatory. Vehicle 340 to be bid shall include all pedestrian and traffic safety systems available from the 341 manufacturer if compatible with upfitting. 342

ALL CAPACITIES, WEIGHTS, MEASUREMENTS, AND RATINGS IN THIS SECTION ARE 344

APPROXIMATES AND TO BE USED AS A BASELINE FOR UNIT TO BE BID UNLESS 345

OTHERWISE STATED AS A SHALL. 346

GENERAL SERVICE/MODEL: 348

_____2026 or current year model Ford Police Interceptor Utility or City approved equal, PPV 349 police pursuit rated (HEV Hybrid Gasoline or Gasoline 3.3L direct-injection FFV V6 350 naturally aspirated engine) AWD SUV 351

_____Seating for five (5) passengers 352 _____GVWR 6,840 lbs. 353 _____Payload capacity 1,670 lbs. 354 _____Tow capacity of 5,000 lbs. 355 _____Wheelbase 119 in. 356

STANDARD FEATURES: 358

_____Police-Calibrated Hybrid Engine System or City approved equal, HEV Hybrid 359 gasoline/electric powertrain with 3.3L direct-injection V6 engine. 360 or 361 _____#99B/44U Gasoline powered engine or City approved equal, 3.3L direct-injection FFV V6 362 naturally aspirated engine 363 _____318 total system horsepower and 322 lbs./ft. total system torque 365 _____This engine shall be certified to meet current EPA & CARB Exhaust & Evaporative 366

Emissions regulations and 50 State 2025 exhaust emissions 367 _____Lithium-Ion battery pack 368 _____220 amp DC/DC converter 369 _____H8 AGM battery rated 92-AH 850 CCA 370 _____250-amp alternator 371 _____Capless fuel filler with 19-gallon fuel tank capacity 372 _____Heavy-duty cooling system to include large high volume radiator, engine oil cooler and 373 transmission oil cooler 374

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

_____AWD drivetrain with 10-speed automatic transmission 375 _____3.73 axle ratio 376 _____Police calibrated high-performance regenerative braking system with heavy-duty brake 377 disc / calipers and 4-wheel anti-lock brake system ABS 378 _____Traction control with roll stability control 379 _____The brakes shall be heaviest duty available for this application 380 _____Front and rear independent suspension with stabilizer bars and heavy duty gas shocks 381 _____Electric power steering with manual tilt and telescoping steering column and column 382 shifter 383 _____Steering wheel to include speed controls and 4-user configurable latching switches 384 _____Four (4) 18 in. x 8 in. 5-spoke painted black steel wheels with polished stainless steel 385 hubcaps 386 _____Four (4) 255/60R18 all-season black sidewall tires 387 _____One (1) full-size spare wheel and tire with TPMS. Spare to be mounted and secured in 388 factory trunk pan location 389 _____Shall have tire pressure monitor system 390 _____Class III trailer tow equipment with Class III trailer hitch receiver, two (2) recovery hooks 391 and lighting package 392 _____Police grade cloth front bucket seats with reduced seatback bolsters designed to 393 accommodate a utility belt and built-in steel intrusion plates in both front-seatbacks 394 _____Driver seat with 6-way power track, 2-way power lumbar and manual recline adjustments 395 _____Front passenger seat with 4-way power track, 2-way power lumbar and 2-way power 396 recline adjustments 397 _____2nd row vinyl 35/30/35 split bench seat with manual fold-flat and fixed seat track 398 _____Manual head restraint at all seating positions 399 _____Shall have 3-point seat belt restraints at all seating positions 400 _____Supplemental restraint system to include latest restraint and airbag technology available 401 for this application 402 _____Assist handles at front passenger-side and rear passenger entry points 403 _____Black-colored heavy-duty rubberized-vinyl floor covering 404 _____Scuff plates at all entry points 405 _____Privacy glass at rear door windows, rear quarter windows and liftgate window 406 _____Manual liftgate with door lock cylinder and fixed window glass with defrost 407 _____Liftgate release switch located in overhead console with 45 second timeout feature 408 _____Overhead console map lamps and red/white task lighting lamps 409 _____Switchable red/white lighting dome lamp in cargo area 410 _____Dark car feature, courtesy lamps disabled when any door is opened 411 _____Front doors to have door checks with supplemental tether straps 412 _____Rear doors to have closeout panels with child-safety locks set to “on” and capped 413 _____Power windows with 1st row 1-touch up/down and disable feature 414 _____Power door locks 415 _____Powerpoints, 12 volt auxiliary power outlets and USB A/C type ports 416

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

_____Center dash universal top tray for mounting aftermarket equipment 417 _____Day/night rear view mirror 418 _____Illuminated instrument cluster with speedometer, tachometer, odometer, trip odometer, 419 fuel, coolant, oil monitor and engine hour/idle hour meter 420 _____Stereo system with 8 in. center-stack display, 4-speakers, AM/FM, MP3 capable, clock, 421 one (1) smart-charging USB-C port and Bluetooth interface with hands-free voice 422 command support 423

_____Rearview camera, viewable through center-stack display with rear camera on demand, 424 allows driver to enable rear camera image via overhead console switch 425

_____Intermittent speed-sensitive front wipers and dual speed rear wipers 426 _____Front climate control, dual zone automatic temperature control HVAC heating, ventilation 427 and air conditioning with particulate filtration 428 _____Rear climate control, auxiliary A/C system 429 _____Exterior manual folding power side-view heated mirrors 430 _____Police headlamp housing with LED wig-wag functionality, automatic LED low/high beams, 431 pre-drilled hole for side marker police use and pre-molded side warning LED capability 432 _____Daytime running lights configurable through instrument cluster 433 _____LED tail lamps with prep kit 434 _____Exterior key locks equipped at both front doors and liftgate 435 _____Shall have four (4) set of OEM simple fleet keys without microchip 436 _____Keyless entry system with four (4) set of OEM remote fobs 437 _____Police engine idle feature. Key can be removed from ignition while vehicle remains idling. 438

Allows engine to be left running and prevents vehicle from unauthorized use when outside 439 of vehicle 440

_____Blind spot monitoring with cross-traffic alert and brake assist 441 _____Police perimeter alert system to include: 442

Detects motion approximately 270° degree radius on sides and back of vehicle 443 Chime will sound at level I if movement is determined to be a threat 444 Doors will lock and windows will automatically go up at level II 445 Visual display in instrument cluster with tracking 446 Enables rearview camera image in the center-stack display 447

_____Pre-collision mitigation system to include: 448 One-touch temporary disable switch for law enforcement use 449 Forward collision warning and automatic emergency braking 450

_____Reverse sensing system 451

STANDARD POLICE UPFIT READY ITEMS: 453

_____9 in. center console mounting plate with 11 in. space between front seats 454 _____Dash pass-thru opening for aftermarket wiring 455 _____Two-way radio pre-wire 456

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

_____Two (2) 50 amp battery power circuits with power distribution junction block located behind 457 2nd row passenger seat floorboard 458

_____Power pigtail harness 459 _____Easy to service headliner 460 _____100 watt siren/speaker prep kit 461 _____Accessory independent timed-release output, output tied to liftgate release switch 462 _____Upfitter interface system located behind 2nd row passenger seat floorboard 463

REQUESTED OPTIONS: 465

OEM option codes for reference only 466 _____#92R Solar tint on 2nd row door glass only and privacy glass on rear quarter and liftgate 467 only 468 _____#51S Left and right Unity LED spot lamps 469 _____#60R RFI noise suppression ground straps 470 _____#52P Hidden door-lock plunger with rear door controls inoperable 471 _____#76D Underbody deflector plate, drivetrain shield 472 _____#153 Front license plate bracket 473 _____#59B Keys to be keyed alike 1284X 474 _____#YZ Oxford White finish color 475

FINISH: 477

_____Before painting, all surfaces shall be cleaned of rust, oil, grease, dirt, mill scale and other 478 foreign contamination 479 _____Vehicle to be painted the manufacturer’s specified standard color and paint to be heaviest 480 duty process available applied over a suitable primer 481 _____The entire understructure is to be undersealed if available 482 _____All paint shall meet California Code of Regulations (CCR) Title 13, Section 1141 Color 483

Requirements. 484

WARRANTY: 486

_____3-year or 36,000 miles, bumper-to-bumper warranty 487 _____5-year or 100,000 miles, powertrain extended warranty 488 _____8-year or 100,000 miles, hybrid/electric components warranty. 489 _____5-year or 60,000 miles, safety restraint system warranty 490 _____5-year or unlimited mileage, corrosion perforation warranty 491 _____5-year or unlimited mileage, paint adhesion warranty 492 _____5-year or 60,000 miles, roadside assistance program 493 _____All warranties shall commence when the City accepts the unit as ready for service. 494

Delivering the unit does not constitute acceptance by the City 495

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

DOCUMENTATION: 497

_____Include one (1) complete set of OEM, parts, repair, and diagnostic manuals for the 498 electrical (including wire diagrams), electronics, engine, transmission, brake system, and 499 drivetrain in electronic form on USB flash drive. Manuals to be delivered with the unit 500

_____Include one (1) operator’s manual per vehicle 501

SECTION 3 – PARK RANGER WHITE CAGED EQUIPMENT UPFIT: 503

The vendor supplied components and outfitting to be furnished under these specifications is to 505 be complete and be performed exactly as requested by the City and County of San Francisco. 506 Specifically, the vendor will provide information on the wire routing for the roof mounted light 507 bar/visor bar and all other electrical / equipment wiring. The components must comply with 508 standard specifications for the model offered with exceptions and additions as contained herein. 509 All equipment shall be installed into a 2026 Ford Interceptor Utility PPV (Police Pursuit Vehicle). 510 Some part numbers may need to be updated to accommodate the newly designed 2026 Ford 511 Explorer Platform. 512

GENERAL: 514

_____Provide and install all manufacturer’s components specified below or City approved equal. 515 _____Provide and install the following components, into a 2026 or current year model Ford 516

Police Interceptor Utility PPV. 517 _____The vendor shall be responsible to deliver all vehicles as specified and equipped in this 518 specification and all respective attachments. 519 _____All technicians and specialists including the supervisor(s) in charge of the group(s) 520 performing vehicle outfitting tasks shall be certified journey level personnel accredited 521 with Automotive Service Excellence (ASE) or Emergency Vehicle Technician (EVT), or 522 any equivalent City approved automotive technician certification program. 523

_____The light bar manufacturer representative shall provide training on diagnosing, repairing, 524 and programming the light bar system, ensuring technicians are proficient in 525 troubleshooting faults, performing necessary repairs, and updating software or 526 configurations per manufacturer specifications. 527

PATROL VEHICLE UPFFITING - PARTS TO BE SUPPLIED BY VENDOR: 529

NOTE: Vendor to verify part numbers and components are up to date, correct, complete 530 and adequate for complete installation of optional accessories. 531

LIGHTS / SIREN / CONTROLS: 533

For Department uniformity, the entire contents of this section SHALL be provided as 534 listed. 535 _____Control unit/control head to operate siren and lighting functions, Federal Signal Pathfinder 536

#PF200S17B, control head to be mounted in overhead console 537

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

_____Auxiliary equipment, Federal Signal On-Scene Sync Module #PFSYNC-1, module to be 538 mounted atop dash center top shelf 539

_____OBD II interface cable for Pathfinder control unit integration #OBDCABLE20-6 540 _____Pathfinder accessory harness rev B2 541 _____Pathfinder output harness rev B 542 _____Low frequency speaker kit and brackets, Federal Signal Rumbler compact speaker pair 543

#RBKIT2-COMPACT, brackets # RBC2-FPIU20ND 544 _____High frequency speaker kit and bracket, Federal Signal DynaMax speaker #ES100C, 545 bracket #ESB-FPIU25NDB 546 _____Roof-mounted lightbar, amber/white warning lights, FSJOIN, Federal Signal 51” Valor Bar 547

#VALR51J-AMBR3, front/rear flood, takedown/alley, rear traffic advisor 548 _____Front headlamp lights, pair of Federal Signal Corner LED lights #416918-AGW, LED tri-549 color light head, amber/green/white 550 _____Mirror lights, pair of SoundOff Signal Intersector exterior undermounted lights 551

#ENT2B3GAW, 18-LED tricolor green/amber/white, 180° viewable 552 _____Quarter window lights and bezel kit, pair of Federal Signal Micropulse Ultra lights 553

#MPS63U-AGW, 18-LED amber/green/white light head, adhesive mount kit #MPSM6U-554

WIN 555

_____Rear tailgate window lights and bezel kit, pair of Federal Signal Micropulse Ultra lights 556 #MPS63U-AGW, 18-LED amber/green/white light head, adhesive mount kit #MPSM6U-557

WIN 558

_____Rear tailgate jamb lights visible with tailgate open, pair of Federal Signal Micropulse Ultra 559 lights # MPS63U-AGW, 18-LED amber/green/white light head 560

_____Rear taillight flasher, Federal Signal #FHL-TAIL, taillight flasher, universal applications, 561 18-inch wire leads562

PUSH BAR: 564

For Department uniformity, the entire contents of this section SHALL be provided as 565 listed. 566 _____Front push bar with accommodations for four (4) Federal Signal lights, Setina PB450L4, 567 push bumper #BK1558ITU20 568 _____Four (4) Federal Signal Micropulse Ultra lights #MPS63U-AGW, 18-LED 569 amber/green/white lights installed in push bumper 570 _____Front push bar fender guards, Setina #PB5 PB400, fender guards #FK0400ITU25 571

SEAT COVERS: 573

_____Front seat covers, Tiger Tough #T52140BLK, black front seat covers designed for law 574 enforcement vehicles. Seat cover set shall cover both front seat bottoms, backs and head 575 rests. 576

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

CENTER CONSOLE: 578

For Department uniformity, the entire contents of this section SHALL be provided as 579 listed. 580 _____Console with printer compartment (to accommodate mobile printer listed below), Troy 581

Products #CC-20UV-PRTR, Ford PIU printer console with 12" of faceplate mounting 582 space, console to include faceplate for Motorola APX 4500 radio unit #FP-MXTL2500 583 (remote head) or #FP-MXTL5000 (full radio unit), and necessary blanks to fill console 584 space. Exact faceplate needed to be determined during pre-construction meeting. 585

_____Console accessory, Troy Products #AC-INBHG, internal dual beverage holder. 586 _____Mobile data terminal MDT mounting components, Troy Products #CM-SDMT-SL-LED, 587 console side-mount computer mount with rotating and extendable slide-arm 588 _____Mobile data terminal MDT mounting components, Gamber Johnson Trimline Toughbook 589

55 dock #7300-0595-00, docking station with lite port, no RF antenna pass-through, no 590 power supply. 591

_____MDT power supply, Lind 120W automobile bare wire leads power adapter for Panasonic 592 #7300-0461 593

NOTE: EXACT FACEPLATE NEEDED TO BE DETERMINED AT PRE-CONSTRUCTION 594

MEETING. 595

PRISONER COMPARTMENT (FULL CAGE): 597

For Department uniformity, the entire contents of this section SHALL be provided as 598 listed. 599 _____Front partition, Troy Products front partition #TP-E-SL6-US-SS, recessed back panel, 600 sliding window w/square hole punch metal screen, large window. 601 _____Rear partition, Troy Products rear partition #TP-20-FDUV-FX2, cargo partition w/square 602 hole punch metal screen rear window and quarter window screens w/fire extinguisher 603 cubby on both sides. 604

_____Rear partition accessory, Troy Products rear partition window #0-PLS-TP-20-FDUV-OS-605 RL, polycarbonate rear partition window panel. 606

_____Partition gap panel, Troy Products rear partition gap panel #AC-20-UV-CGP2-PTS, 607 polycarbonate rear partition gap panel. 608

CARGO EQUIPMENT: 610

For Department uniformity, the entire contents of this section SHALL be provided as 611 listed. 612 _____Tailgate glass window barrier, Troy Products window screen #AC-20-UV-HATCH, square-613 hole punched 614 _____Two (2) rear tailgate struts 615 _____Rear cargo deck system, Troy Products #EM-20UV-CRGDCK-SSTK-2DWR, electronics 616 mounting cargo deck with two-drawer system, stop stick cubby and removeable organizer 617 tray. Storage drawer with push button lock security. Electronics drawer with keyed lock 618 security. 619

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

MOBILE DATA TERMINAL MDT AND COMMUNICATION EQUIPMENT APPROVED BY 621

SFPD/DEPARTMENT OF TECHNOLOGY, TO BE SUPPLIED BY VENDOR: 622

LAPTOP/NOTEBOOK: 624

For Department uniformity, the entire contents of this section SHALL be provided as 625 listed. 626 _____The current standard issued equipment SFPD have approved for use is Panasonic laptop 627

#FZ-55JA-00BM. This is informational and for upfitting vendor purposes only. Upfitting 628 and pre-wiring shall be compatible with this equipment. DO NOT SUPPLY LAPTOP IN 629

BID. 630

_____End user department to provide cabling and associated components currently in use for 631 upfitter installation. 632 Laptop/notebook device, Panasonic laptop #FZ-55JA-00BM with the following:633 Toughbook FZ-55 rugged laptop is certified to MIL-STD-810H & IP-53 standards634 and includes Windows 11 Pro, Intel Core i7-1370P vPro (up to 5.2GHz), AMT, 14.0"635 FHD 1000 nit gloved multi-touch display, magnesium alloy case & handle, pre-636 installed 16GB RAM (DDR4-3200MHz), graphics card, Intel Wi-Fi 6E, Bluetooth,637 4G EM7511, GPS, dual pass (Ch1:GPS/Ch2:WWAN), mic and infrared 2MP638 webcam, standard battery, TPM 2.0, emissive backlit keyboard, flat, 3 Year no return639 of defective drive, 3 year protection plus warranty, 3 year premier deployment, and640 Toughbook field engineering service. ground shipping is included.641

1TB OPAL SSD upgrade #FZ-VSDR553TW642 16GB RAM upgrade #FZ-BAZ2216IS643 VGA + Serial (true) + LAN xPAK rear expansion #FZ-VCN552WIS644 Barcode reader Xpack #FZ-VBR552M645

MOBILE PRINTER: 647

For Department uniformity, the entire contents of this section SHALL be provided as 648 listed. 649 _____In-vehicle mobile printer, Brother PocketJet 883L printer #PJ-883-L, high-resolution full-650 page mobile printer with USB-C, Wi-Fi, Airprint, Bluetooth wireless technology, battery, 651 power cables, 3-year warranty, printer paper rolls (6), and an installation wiring kit, printer 652 to fit in specified center console’s printer compartment. 653

_____One (1) USB cable, 3’ length, supports power and data, connects from MDT USB port to 654 printer USB port. 655

NOTE: EXACT PRINTER AND COMPONENTS NEEDED TO BE DETERMINED DURING PRE-656

CONSTRUCTION MEETING. 657

WIRELESS RECEIVER / WI-FI EQUIPMENT: 659

For Department uniformity, the entire contents of this section SHALL be provided as 660 listed. 661

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

_____The current standard issued equipment SFPD have approved for use is Ericsson 662 Cradlepoint R1900 #MB03-19005GB-GA, RX30-MC managed dock #MB-RX30-MC,. 663 MC400 Modular Modem #MB-MC400-5GB. This is informational and for upfitting vendor 664 purposes only. Upfitting and pre-wiring shall be compatible with this equipment. DO NOT 665

SUPPLY CRADLEPOINT COMPONENTS IN BID. 666

_____End user department to provide cabling and associated components currently in use for 667 upfitter installation. 668 5G router / primary modem equipment, Ericsson Cradlepoint R1900 5G LTE Cellular669

Rugged Router with 3-year NetCloud Mobile Performance Essentials plan # MB03-670 19005GB-GA, embedded 4x4 MIMO 5G LTE modem with Cat 20 performance, 2x2671 WiFi 6, GPS, and an assortment of I/O interfaces.672

Router switch / dock with expansion slot, Ericsson Cradlepoint RX30-MC managed673 dock #MB-RX30-MC, mates to the R1900 5G cellular router to provide a 4-port674 Gigabit Ethernet switch and an expansion slot for the MC400 modem.675

Secondary modem, Ericsson Cradlepoint MC400 Modular Modem with 5G676 Performance #MB-MC400-5GB, secondary 5G modem upgrade for the677 R1900+RX30-MC mobile routers with doors, no antennas, (requires 4FF SIM)678

VENDOR TO SUPPLY AND INSTALL ANTENNAS IN BID. 680

_____Antenna equipment, Panorama 7-in-1 5G dome blk -FTD extended cables, #LP-IN2445 681 _____Antenna equipment, Panorama 4-in-1 4x4 MIMO 5G dome (black), #LP-IN2443 682 _____Antenna equipment, Panorama foam pad for installation of the dome antenna on uneven 683 surfaces, Qty. two (2) #LGMM-EXT-R-SLT 684

RADIO EQUIPMENT: 686

For Department uniformity, the entire contents of this section SHALL be provided as 687 listed. 688 _____The current radio communication equipment SFPD have approved for use is Motorola 689

APX4500 7/800 radio #M22URS9PW1. This is informational and for upfitting vendor 690 purposes only. Upfitting and pre-wiring shall be compatible with this equipment. DO NOT 691

SUPPLY RADIO IN BID. 692

_____End user department to provide radio cabling and associated components currently in use 693 for upfitter installation, two (2) power pigtails, one (1) radio data cable, one (1) antenna 694 whip & cable, one (1) mounting bracket. 695

VENDOR TO SUPPLY SPEAKER AND INSTALL COMPONENTS AS SPECIFIED. 697

_____Communication equipment, Motorola speaker #HSN4031B, 7.5W external speaker 698 module assembly 699 _____Pre-wire for one (1) Motorola APX4500 remote mounted radio systems located in center 700 console slant surface. 701

Budget# REC25039-40

ATTACHMENT 6 VEH# 65100800-01

EQUIPMENT SPECIFICATION FOR A

POLICE PURSUIT RATED PPV AWD SUV

MARKED WHITE CAGED PATROL UNIT

REVISION DATE: 04/22/2026

MISCELLANEOUS INSTALLATION COMPONENTS AND JOB MATERIALS: 703

_____One (1) power management and distribution system (PDU). PDU to support multiple 704 circuits with power management of high/low voltages and timed/constant power. Shall 705 support all proposed electronics and have additional circuits for future expansion. 706

_____One (1) forward alarm, Ecco audible forward alarm #DT500 707 _____One (1) radio antenna cable, 3/4" hole NMO brass mount with 17’ RG58U cable and no 708 connector, #MB8U 709 _____One (1) radio antenna mount cap, black rain cap for NMO mounts, #ANXQWRCB-L 710 _____Three (3) magnetic mic conversion kit, #MMSU1 711 _____Job materials, electronics board with carpet, misc. parts, wire, zip ties, clamps, fasteners, 712 fuses, fuse block, circuit breakers, relays, etc., use cat 6 cabling. 713 _____Audible carbon monoxide detector, Kiddie 3010D Worry Free carbon monoxide alarm with 714 digital display and ten (10) year sealed battery #21026047 715 _____Visual carbon monoxide detector, Quantum Eye carbon monoxide detector, eighteen (18) 716 month 717 _____One (1) Amerex #B500 & #861H, 5 lbs. ABC fire extinguisher and heavy-duty mounting 718 bracket. Fire extinguisher to have signed inspection tag upon delivery. 719 _____One (1) Uline #H-1293, OSHA approved 25-person first aid kit. 720 _____Furnish and install location labels for fire extinguisher and first aid kit. Installed to lower 721 rear edge of both rear doors. 722 _____One (1) James King & Co. #1005 & #1005-B, triangular highway reflector kit and mounting 723 bracket. 724 _____One (1) box of road flares, box of Orion 30-minute road flares, 36 flares each box.