Salients.pdf
PDF 145 KB Posted
- Attached to
- ROLLER GRINDER
- Solicitation number
- SPMYM222Q2599
View the file
Other files
| File | Type | Posted |
|---|---|---|
| 22063808_CDRLs 3.pdf | ||
| 22063807_CDRLs 3.pdf | ||
| 22Q2599 ROLLER GRINDER.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Salient for JML: 2206-3807
G & P Model RG-4132-5 Abrasive Belt roll Grinder or equivalent.
The base plate of the roller grinder shall be constructed of 3/4''thick steel plate and machined on the bottom to approximately 11/16'' thick.
The grinder shall be able to mount on the front side of a lathe.
The roller grinder shall include a type 1 lathe mounting adapter.
The roller grinder shall come with a complete and ready to use, less abrasive belt and dust collector.
The motor shall meet the following electric requirements:
- 5 HP
- 3600 RPM,
- TEFC high efficiency motor wired to operate at 230/3/60 VAC.
The motor shall has a magnetic starter with motor overload protection
The motor transformer shall provide 110 volts at the push buttons and have a NEMA 12 enclosure.
The abrasive belt shall have the following features:
- Air tension on 4'' x 132'' abrasive belt
- Abrasive belt guard with 4'' OD dust exhaust port
- Guarded v-belt drive
- 5500 feet per minute abrasive belt speed
The roller grinder shall have a crowned aluminum pulley that has a 9'' diameter and is 4 1/4'' wide.
The roller grinder shall have a precision duplex ball bearings on its spindle.
The shaft shall be tapered for use with and 8'' diameter contact wheel with 1-1/4-7-RH brass hex nut.
The tapered bore contact wheel shall be an 8” diameter x 4-1/8 wide, SDDR (Serrated Dual Density Rubber) type.
The roller grinder shall have a pivoting lock bar that locks the tubular member in place at the angle that any angle up to 35 degrees.
DDQ0001
Highlight
Salient for JML: 2206-3808
G & P Model RGL-4132-5 Abrasive Belt roll Grinder or equivalent.
The base plate of the roller grinder shall be constructed of 3/4''thick steel plate and machined on the bottom to approximately 11/16'' thick.
The grinder shall be built opposite/left hand so it can be mounted on the backside of a lathe.
The roller grinder shall include a type 1 lathe mounting adapter.
The roller grinder shall come with a complete and ready to use, less abrasive belt and dust collector.
The motor shall meet the following electric requirements:
- 5 HP
- 3600 RPM,
- TEFC high efficiency motor wired to operate at 230/3/60 VAC.
The motor shall has a magnetic starter with motor overload protection
The motor transformer shall provide 110 volts at the push buttons and have a NEMA 12 enclosure.
There shall be at least 20 feet of electrical cable between the unmounted started and grinder.
The abrasive belt shall have the following features:
- Air tension on 4'' x 132'' abrasive belt
- Abrasive belt guard with 4'' OD dust exhaust port
- Guarded v-belt drive
- 5500 feet per minute abrasive belt speed
The roller grinder shall have a crowned aluminum idler pulley that has a 9'' diameter and is 4 1/4'' wide.
The roller grinder shall have a precision duplex ball bearings on its spindle.
The shaft shall be tapered for use with and 8'' diameter contact wheel with 1-1/4-7-RH brass hex nut.
The tapered bore contact wheel shall be an 8” diameter x 4-1/8 wide, SDDR (Serrated Dual Density Rubber) type.
The roller grinder shall have a pivoting lock bar that locks the tubular member in place at the angle that any angle up to 35 degrees.
DDQ0001
Highlight
File details come from the government source that posted it. Updated .