Salient Characteristics (Redacted).doc
DOC document 77 KB Posted
- Solicitation number
- W911QX26QA056
About this file
This is a Salient Characteristics document certifying commercial availability for a federal procurement. The Government is procuring three pulsed neodymium: yttrium aluminum garnet (Nd:YAG) lasers and one Aiming Beam Module for alignment, to be delivered to Logistics Warehouse Building 321, 6375 Johnson Road, Aberdeen Proving Ground, Maryland 21005. The laser systems must have a tunable energy range from 0 to at least 850 millijoules per pulse, pulse width between 5 to 7 nanoseconds, wavelength of 1,064 nanometers, and pulse repetition rate of 10 Hertz with single-shot capability. Additional technical requirements include beam diameter between 7 to 12 millimeters, beam divergence less than 0.5 milliradians, pulse-to-pulse energy stability of 2 percent for at least eight hours, and thermal stabilization of the laser housing. The power supply must accommodate 100-240 Volts AC, 50/60 Hertz, single phase, 1100 volt-ampere, with maximum dimensions of 25" x 25" x 15", and power supplies must be interchangeable without recalibration. The laser head shall not exceed 25" x 10" x 10".
The contractor must provide quick connect cables, coolant lines, a remote control unit for laser parameter control, an air-to-water heat exchanger operating between 18 to 28 degrees Celsius, software for computer-based laser firing, four replacement in-line water cartridges, a quick installation kit, shipping to the destination with insurance, and a minimum two-year warranty. The Aiming Beam Module must be compatible with the laser systems, use a visible class two laser collinear to the main beam for alignment purposes, and be directly interchangeable with any laser system in a plug-and-play configuration. A critical contractor qualification requirement is that the bidder must have sold at least two identical laser systems within the last two years and provide references upon request. The contracting agency is the Department of the Army Materiel Command Army Contracting Command at Aberdeen Proving Ground, with solicitation number W911QX26QA056.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Provisions and Clauses Full-Text.docx | DOCX document | |
| Combination Synopsis-Solicitation for Commercial Purchases (Under SAT)_.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Salient Characteristics
Commercial Availability Certification:
I have evaluated the commercial marketplace and determined that all of the salient characteristics documented below are available in products/services offered in the commercial marketplace.
Signature (typed name): [Redacted] Technical Point of Contact (TPOC)
The Contractor shall provide three (3) pulsed neodymium: yttrium aluminum garnet (Nd: YAG) lasers and one (1) Aiming Beam Module for alignment.
The laser systems shall meet or exceed the following requirements:
· A tunable range from zero (0) to at least eight hundred fifty (850) millijoules (mJ) of energy per laser pulse
· Laser pulse width between five (5) to seven (7) nanoseconds (ns)
· Laser wavelength of 1,064 nanometers (nm)
· Pulse repetition rate of ten (10) Hertz (Hz), with single-shot capability
· Beam diameter between seven (7) to twelve (12) millimeters (mm)
· Beam divergence less than zero point five (0.5) milliradians (mrad)
· A pulse to pulse energy stability of two (2) percent (%) for at least eight hours
· Must include a power supply with 100-240 Volts Alternating Current (VAC) and 50/60 Hertz (Hz), single phase, 1100 volt-ampere (VA)
· Power supply/cooler should be no larger than 25 inches (“) x 25” x 15”
· Power supplies must be interchangeable without recalibration
· Must include quick connect cables and coolant lines
· Laser head should be no larger than 25”x10”x10”
· The laser housing shall be thermally stabilized
· Must include a remote control unit to interface with laser to control laser parameters
· Must include a cooling unit with an air to water heat exchanger that operates between 18 to 28 degrees Celsius (°C)
· Must be an air to water heat exchanger
· Must include a quick installation kit
· Must include software to enable user interface for firing the laser via computer
· Must include four (4) replacement in-line water cartridges
· The Contractor shall provide shipping to Destination and shipping insurance
· The Contractor shall provide a minimum two (2) year warranty
· The Contractor must have sold at least two (2) identical laser systems in the last two (2) years and provide references upon request.
The Aiming Beam Module shall meet or exceed the following requirements:
· Module shall be compatible with the provided laser systems
· Must use a visible class two (2) laser collinear to the main laser beam for the purposes of laser beam alignment
· Directly interfaces and is interchangeable with any of the laser systems (plug and play).
Place of Delivery: Logistics Warehouse Building 321,6375 Johnson Road
Aberdeen Proving Ground, MD 21005 Contracting Officer:
Template last updated 07/28/2016
File details come from the government source that posted it. Updated .