RFQ_274211_10.08.26_(003).pdf

PDF 373 KB Posted

Attached to
RFQ Design Build Services
Solicitation number
274211
Issued by
Gillespie County, Amarillo City, Texas

About this file

This is a Request for Qualifications (RFQ) issued by Grimes County, Texas, for Design-Build services to expand, renovate, and/or construct additions to the Grimes County Law Enforcement Center located at 382 FM 149, Anderson, Texas 77830. The project seeks to increase inmate housing capacity, with potential outcomes ranging from 81 to 273 additional beds for expansion/renovation or 192 to 384 beds for new construction. The scope encompasses architectural, civil, structural, mechanical, electrical, plumbing, fire protection, life-safety, detention equipment, electronic security and access control, communications, and site improvements. The facility will remain operational throughout construction with work conducted in phases. A non-mandatory site visit was scheduled for December 3, 2026, with the deadline for submitting qualifications set for December 14, 2026, at 2:00 p.m. Interviews for shortlisted firms and fee proposal submissions were anticipated to occur at dates to be determined. Construction completion is targeted for October 2029. Proposals were limited to 30 pages and must address organizational information, project experience with at least three similar Design-Build projects completed within five years, project team qualifications, management approach, and other specified criteria.

The RFQ indicates that a final project budget has not been established; the selected Design-Builder will assist Grimes County during the Pre-Construction phase with programming, investigation, cost estimating, and value engineering to develop and refine the budget. Fees were not required with the initial qualifications submission but will be requested during the interview and fee proposal phase for shortlisted candidates. Evaluation of proposals will be based on 100 points distributed across experience (60 points), work performance (25 points), and capacity to perform (15 points). The Client reserves the right to reject any or all responses, conduct investigations regarding respondent qualifications and financial ability, and to negotiate with the highest-ranked firm; if negotiations fail, negotiations may proceed with second- or third-ranked firms. All trade contracts are anticipated to be competitively bid in accordance with local, state, and federal requirements, with the Design-Builder responsible for self-performed work and project controls. Any cost savings realized during design refinement and construction shall revert entirely to Grimes County, with no shared savings compensation to the Design-Builder.

View the file

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

REQUEST FOR QUALIFICATIONS (RFQ)

DESIGN BUILD SERVICES

for Grimes County Law Enforcement Center Expansion / New Construction

Contract # 274211

Grimes County, Texas

Page 2 of 23 Grimes County Design-Build RFQ

TABLE OF CONTENTS

1.0 GENERAL INFORMATION

1.1 INTRODUCTION AND PROJECT DESCRIPTION

1.2 LOCATION

1.3 BUDGET

1.4 GENERAL DESIGN BUILD SCOPE OF SERVICES

1.5 CONTACTS

1.6 SCHEDULE OF EVENTS

1.7 PROPOSAL INSTRUCTIONS

1.8 PROPOSAL REQUIREMENTS

1.9 QUESTIONS, INQUIRIES, AND AMENDMENTS REGARDING THIS RFQ/P

1.10 PROPOSING FIRMS TO FULLY INFORM THEMSELVES

1.11 EVALUATION & SELECTION CRITERIA

1.12 SELECTION PROCESS

1.13 RIGHT OF REJECTION

1.14 MODIFICATION AND WITHDRAWAL OF PROPOSAL

1.15 PROPOSALS TO REMAIN OPEN SUBJECT TO ACCEPTANCE

1.16 COST OF PROPOSALS

2.0 PROPOSAL FORM

2.1 PROPOSAL FORM FOR DESIGN BUILDER

3.0 ATTACHMENTS

3.1 EXHIBIT A: PRELIMINARY SITE CONDITIONS / PROJECT INFORMATION

Project Location: Grimes County Law Enforcement Center, 382 FM 149, Anderson, Texas 77830. The final expansion/new-construction configuration is to be determined through the Design-Build process. The facility will remain operational throughout construction and work will be phased. The selected DESIGN BUILDER shall verify all existing conditions and coordinate non-destructive testing and other investigations necessary to support design and construction.

Additional record information, site access, and available drawings will be coordinated by the Client during the selection and Pre-Construction process.

3.2 EXHIBIT B: DESIGN BUILD AGREEMENT, STANDARD AIA A141 (copy not included) To be provided by Firm at award.

3.3 EXHIBIT C: PRICING LINE-ITEM SHEET

Page 3 of 23 Grimes County Design-Build RFQ

Page 4 of 23 Grimes County Design-Build RFQ

1.0 GENERAL INFORMATION

1.1. INTRODUCTION AND PROJECT DESCRIPTION

This Request for Qualifications (RFQ) is issued to provide the selection process for DESIGN BUILD services for the expansion, renovation, and/or new construction of the Grimes County Law Enforcement Center. Firms (hereinafter identified as DESIGN BUILDERS) submitting responses to the RFQ will be asked, at a minimum, to state their understanding and experience with projects of similar size, function, security requirements, and complexity and to provide their methodology for meeting the criteria identified in this RFQ. The shortlisted finalists may be requested to participate in an interview. At that stage of the selection process, respondents may be asked to provide additional project information, preliminary recommendations, scheduling information, and a fee proposal for the work as outlined in this RFQ.

Background:

Grimes County (hereinafter identified as the “Client”) owns and operates the Grimes County Law Enforcement Center located at 382 FM 149, Anderson, Texas 77830. The Client is seeking a qualified Design-Build team to evaluate the existing facility and develop a comprehensive solution for increasing inmate housing capacity. If expansion and/or renovation of the existing facility is determined to be the preferred approach, the project may provide approximately 81 to 273 additional beds. If new construction is determined to be the preferred approach, the new facility may provide a total of approximately 192 to 384 additional beds. The final project scope, configuration, and bed capacity have not yet been determined and may include expansion and renovation of the existing facility, new construction, or a combination thereof.

The selected DESIGN BUILDER shall evaluate existing conditions, operational and security requirements, site constraints, infrastructure, constructability, cost, phasing, and long-term facility needs in developing and recommending the most appropriate project approach.

Grimes County Law Enforcement Center

The existing Law Enforcement Center will remain operational throughout construction. The Project shall therefore be planned and constructed in phases to maintain safe, secure, and continuous law enforcement and detention operations. The DESIGN BUILDER shall coordinate phasing, temporary conditions, access, utility interruptions, inmate and staff movement, contractor access, and security measures with the Client throughout the Project.

Project Goals and Existing Conditions

The Project is intended to evaluate and develop the most appropriate solution for increasing inmate housing capacity at the Grimes County Law Enforcement Center. If expansion and/or renovation of the existing facility is determined to be the preferred approach, the Project may provide approximately 81 to 273 additional inmate beds. If new construction is determined to be the preferred approach, the Project may provide approximately 192 to 384 additional inmate beds. The final bed capacity, configuration, and project approach have not yet been determined and will be developed based upon the Client’s operational needs, existing facility conditions, site constraints, available infrastructure, constructability, phasing requirements, and overall project cost.

The Project shall include the support spaces, detention systems, building systems, infrastructure, security improvements, and site improvements necessary for the safe, secure, and efficient operation of the proposed facility improvements.

The DESIGN BUILDER shall perform appropriate investigation and evaluation of the existing facility and site, including, but not limited to, non-destructive testing (NDT) as necessary to evaluate existing structural components, concrete conditions and thicknesses, utilities, building systems, and other existing conditions that may affect the feasibility, design, renovation, expansion, new construction, or connections between existing and new construction.

Page 5 of 23 Grimes County Design-Build RFQ

Project Description:

Grimes County Law Enforcement Center Expansion / New Construction

The Client is seeking a qualified Design-Build team experienced in the planning, design, renovation, expansion, and construction of secure detention and law enforcement facilities. The DESIGN BUILDER shall evaluate renovation, expansion, new construction, or combinations thereof and recommend a solution that best addresses capacity, security, operations, constructability, schedule, phasing, and cost. The Project may include, but is not limited to, architectural, civil, structural, mechanical, electrical, plumbing, fire protection, life-safety, detention equipment, electronic security and access control, communications, surveillance, site utilities, infrastructure improvements, site work, and other improvements determined necessary during programming and design development.

Operational Continuity and Phasing

Because the Law Enforcement Center is an active secure facility, the DESIGN BUILDER shall develop a detailed construction phasing, security, logistics, and operational-continuity plan. The plan shall maintain required detention and law enforcement functions; provide secure separation of inmates, staff, contractors, and the public; control construction access and deliveries; coordinate utility shutdowns; maintain critical life-safety, communications, surveillance, and electronic security systems; address temporary barriers and secure partitions;

and minimize noise, dust, vibration, debris, and other impacts on ongoing operations.

1.2 LOCATION

Grimes County Law Enforcement Center

382 FM 149, Anderson, Texas 77830

1.3. BUDGET

The current project budget has not yet been established. The selected DESIGN BUILDER will assist the Client during Pre-Construction with programming, investigation of existing conditions, non-destructive testing, cost estimating, value engineering, constructability review, phasing analysis, and evaluation of project alternatives to develop and refine the Project budget. The final Guaranteed Maximum Price (GMP) shall be developed in accordance with the Client’s requirements and the Design-Build Agreement.

1.4 GENERAL DESIGN BUILD SCOPE OF SERVICES

The exact scope of services required by the Client will be set forth in the agreement between the Client and the selected DESIGN BUILDER. The scope will include assisting the Client’s staff and consultants through programming, investigation, Pre-Construction, design, permitting/agency coordination, phased construction, commissioning, closeout, and warranty.

The DESIGN BUILDER shall account for the Law Enforcement Center remaining operational throughout the Project and shall coordinate with all authorities having jurisdiction over detention, life-safety, accessibility, and building requirements. The DESIGN BUILDER will prepare a final Guaranteed Maximum Price (GMP), anticipated at 100% design documents, for consideration and approval by the Client.

The DESIGN BUILDER’s services during the Pre-Construction Services phase shall include, but may not be limited to, confirming the program and bed-capacity requirements; evaluating

Page 6 of 23 Grimes County Design-Build RFQ renovation, expansion, and/or new-construction alternatives; performing and coordinating non-destructive testing and existing-condition investigations; design and cost estimating; value engineering; scheduling and phased logistics planning; security and operational-continuity planning; constructability analysis; bid package administration; bidding of trade contracts; and submittal of a GMP Proposal reflecting the entire cost, scope, and quality intent of the Project before construction funds are committed.

The DESIGN BUILDER’s services during the Construction Services phase shall include, but may not be limited to, site and building design, phased construction management, construction administration, field supervision, coordination of subcontractors, detention and security systems coordination, maintaining quality and schedule, maintaining secure facility operations, and providing the general conditions work necessary to complete the Project in compliance with the contract documents.

Generally, all trade contracts shall be competitively bid in accordance with all appropriate local, state and federal requirements, and assigned to the DESIGN BUILDER’s contract; however, when circumstances warrant it, the DESIGN BUILDER will be allowed to self- perform work that it traditionally performs with its own forces. This work shall be competitively bid by the DESIGN BUILDER, with results managed by the Owner’s Rep., against other contractors performing the same scope of work.

The DESIGN BUILDER shall implement and maintain a project controls system with full access to the project information by all project stakeholders. The DESIGN BUILDER shall allow for “open book” policy and facilitate review of all Project contracts, records, accounting and other documentation and information, in any form, to the Client or persons designated by the Client for auditing purposes.

A. PRE-CONSTRUCTION SERVICES FIXED FEE

The DESIGN BUILDER shall participate in the continuing of the design process as an integral member of the Project Team and shall perform Pre-Construction Services that, in general, shall include but not be limited to the following:

1) Schedule, attend and manage all necessary design work sessions with the Client and Design Team to gather and distribute information on the Project as required.

2) In conjunction with the Client and Design Team, immediately identify the Project requirements and prepare comprehensive construction budgets. DESIGN BUILDER to identify all project related construction costs including (but not limited to) building and site construction, infrastructure improvement costs (on-site and off-site), construction within right- of-way, permitting and other such costs that may be of consequence to Client.

3) Develop and continue to refine a comprehensive Project Schedule. Identify, set decision dates, and make recommendations to the Client and the Design Team on procurement of long-lead delivery items. Update and monitor the Project Schedule with the Client and the Design Team regularly to identify deviations and changes.

4) Provide value engineering and life-cycle costing for all materials, equipment and systems mutually agreed upon to determine the best possible value to the Client. Conduct formal value engineering work sessions with the Client and the Design Team, and recommend design detail, system and assembly alternatives. Prepare and monitor estimates of the construction cost during each of the design phases based on detailed quantity surveys of the Drawings and Specifications. Advise the Client and the Design Team if it appears that the construction budget will not be met and make recommendations for corrective action. Prepare and update with each cost estimate a reconciliation report comparing the previous cost estimate, the current cost estimate, and the approved budget. Provide a narrative of the changes made from the previous versions and accompanied with an updated construction billing and cash flow forecast. Provide this service at each design milestone: Schematic Design Package, Design Development (100% DDs); Permit Drawings (100% Construction Documentation [CDs]). In addition to providing periodic estimates, it is expected that DESIGN BUILDER will work cooperatively with Client and the Design Team to provide intra-phase pricing evaluations of building systems, assemblies, Page 7 of 23 Grimes County Design-Build RFQ and component options to facilitate timely design related decision-making as required by the Client and the Design Team.

5) Review the drawings and specifications as they are being prepared, and recommend alternate solutions whenever design details affect budget, schedule, constructability, and consistency with local and traditional trade practice.

6) Review the proposed design concepts, layouts, dimensions, clearances and advise the Client and the Design Team of possible conflicts of the Mechanical/Electrical/Plumbing (M/E/P) building systems with the adjacent structure and finishes. DESIGN BUILDER to confirm accuracy of Civil Engineer’s earthmoving, import and export quantity assumptions prior to providing GMP. Perform and/or coordinate non-destructive testing and existing-condition investigations as necessary to evaluate structural components, concrete, utilities, building systems, and other concealed or uncertain conditions. Document findings and incorporate them into design recommendations, cost estimates, constructability reviews, phasing plans, and the GMP. Where conditions cannot reasonably be verified non-destructively, identify the limitation and recommend additional investigation to the Client before affected work proceeds.

7) Recommend a strategy for bid packaging the drawings and specifications relative to the Project approach and other pertinent considerations. Administrate the various bid packages for the Project.

8) Recommend and prequalify subcontractors and contact suppliers to develop a bidder’s list for review and approval by the Client and the Design Team. It is the Client’s policy that only prequalified subcontractors and suppliers shall be invited to bid on various procurement packages on the Project and, further, that awards are then based upon the lowest responsible and conforming bids received. Minimum of four (4) bids per subcontract or subtrade, including work to be self-performed, unless otherwise agreed to by Client.

9) Prepare a detailed approach to phasing of the work, mobilization, secure construction access, inmate/staff/public separation, logistics, temporary barriers, utility interruptions, quality control, emergency access, and safety. The plan shall specifically address construction adjacent to and within a continuously operating detention and law enforcement facility and shall be reviewed with the Client and Design Team before affected work begins.

10) Prepare and submit a final GMP Proposal for the Client’s optional acceptance reflecting the entire cost, scope of work and quality intent of the Project before any construction funds are committed. The GMP Proposal shall be supplemented with a clearly defined and detailed breakdown of costs for the entire Project. All construction costs must be clearly defined and included in the GMP Proposal. All proposed allowances included shall be approved by the Client and shall include estimated quantities and values justified by the DESIGN BUILDER. All clarifications, exclusions, exceptions must be identified within your proposal.

11) Identify and submit proposals for long lead items for direct purchase by the Client.

12) Include costs for and coordinate with all authorities having jurisdiction over the Project in order to obtain required permits, reviews, approvals, and inspections on a timely basis. The DESIGN BUILDER shall coordinate requirements applicable to detention and law enforcement facilities and shall identify required agency reviews during pre-construction.

B. CONSTRUCTION SERVICES FEE

The DESIGN BUILDER shall construct the work according to the construction documents and specifications within the scheduled time frame agreed to with the Client.

1. The DESIGN BUILDER will purchase Online Project Management software and allow Grimes County’s Representatives to track project related information including but not limited to RFI’s, ASI’s, Submittals, Punch List, Warranty Items, O&M Manuals.

2. The DESIGN BUILDER will be required to provide warranty and closeout assistance. Warranty on items will be for a minimum of 2 years.

Please refer to Exhibit A for available project/site information and scope clarification. Because the final expansion/new-construction configuration has not yet been determined, the DESIGN

Page 8 of 23 Grimes County Design-Build RFQ

BUILDER shall verify existing conditions and shall not rely solely on record drawings or preliminary information. Fees are not due with the initial qualifications submission but will be required during the interview/fee proposal phase if the DESIGN BUILDER reaches that stage.

C. COST SAVINGS

To the extent the actual cost of the work may be reduced through the course of the design refinement, Procurement and Construction, the reduction in cost shall revert entirely to the benefit of the Client. There shall be no “shared savings” compensation to the DESIGN

BUILDER.

D. CONSTRUCTION CHANGE ORDER MARK-UP

For Client approved changes to the scope of work, the DESIGN BUILDER shall propose a Percentage Fee for additive and deductive change orders to the GMP Contract amount.

Deductive change orders will be credited only for the cost of the work.

E. SCHEDULE

The final Project Schedule is not certain at this time. The DESIGN BUILDER shall develop a comprehensive schedule during pre-construction that addresses design, agency reviews, procurement, long-lead detention/security items, phased construction, testing, commissioning, occupancy transitions, and final completion while maintaining continuous operation of the Law Enforcement Center. Notice to Proceed for Pre-Construction Services: ____________. Notice to Proceed for Construction Services: ____________. Anticipated Construction Completion:

F. BIDDING & CONSTRUCTION CONTINGENCY

The DESIGN BUILDER’S contingency shall be used to cover costs of unforeseen job conditions, omissions of the estimate (with the exception of subcontracted work), and discrepancies between subcontractor and supplier scopes of work, which are properly reimbursable as Cost of the Work but are not the basis for a change order. The DESIGN BUILDER’S contingency shall be used with the Client’s and the Design Team’s concurrence ONLY, which shall not be unreasonably withheld. Requests for the use of the contingency shall be submitted by the DESIGN BUILDER within ten (10) calendar days of the event that caused such Cost of Work to be incurred, or as soon as the need is apparent, whichever is earlier. The DESIGN BUILDER’s contingency shall not be used for repairing or replacement of the Work due to the DESIGN BUILDER’s negligence or error. The contingency may be refunded via change order to the owner in stages as agreed upon by the team and the balance of the DESIGN BUILDER’S contingency which has not been expended for the Project according to the procedures set forth herein shall be refunded entirely to the benefit of the Client, upon final invoicing. The DESIGN BUILDER shall also provide the Client and the Design Team documented status of the contingency amount on a monthly basis with each payment application. The OWNER will carry a separate contingency for changes to the work.

1.5 CONTACTS

Submission of this RFQ should be delivered by 2:00 pm on Monday, December 12, 2026 Monday, December 14,2026(See addendum #1).

Page 9 of 23 Grimes County Design-Build RFQ

Grimes County Auditor’s Office

270 FM 149 W Anderson, TX 77830

Attn: Danya Lewis

Or electronically:

Danya.Lewis@grimescountytexas.gov

Copies of this RFQ are available from the Client’s Owner Representative.

Owner’s Representative: Grimes County

Project Manager: Rodney Floyd

Phone: 936-873-4452

Email: maintenance@grimescountytexas.gov

Notice: Direct contact with the Client, the Board, or other related parties, may cause DESIGN BUILDER to be removed from the RFQ process.

1.6 SCHEDULE OF EVENTS

The anticipated schedule below outlines milestones for the project:

DATE TIME EVENT

10/15/2026 DESIGN BUILD RFQ Issued

12/03/2026 10:00 A.M.

Non-Mandatory site visit - Grimes County Law Enforcement Center

12/08/2026 11:00 A.M. Deadline for receipt of questions and inquiries

12/09/2026 Final responses to questions

12/14/2026 2PM

Deadline for submission of qualifications from DESIGN BUILD candidates

TBD TBD

Interviews of short-listed firms (if needed) AND Submission of Fee Proposals

TBD

Commissioners Court Approval of Design Builder Selection

TBD Finalize contract negotiations

OCTOBER 2029 Construction Complete

1.7 PROPOSAL INSTRUCTIONS

The Client is looking to base their decision on qualifications of the proposing firms and is requesting that items related to Fee not be submitted for this phase of the selection process.

A. Pages in the proposal shall be typed with the maximum number of pages of proposal information (excepting cover sheet, index sheet, blank pages, table of contents, AIA 305, similar project profile sheets, and other supplemental proposal forms required or requested) to be limited to thirty (30) pages numbered in sequential order.

Page 10 of 23 Grimes County Design-Build RFQ

B. Submit a single electronic PDF file or 3 hard copies of your proposal by the submittal date/time aforementioned; email to danya.lewis@grimescountytexas.gov . It is advised to request a read receipt when submitting. If email is not possible submit one thumb drive by the Proposing Firm containing the completed RFQ response to the County Auditor’s Office listed in Section 1.5 above. Oral, telephonic, or faxed proposals are invalid and will be considered non-responsive.

C. Each respondent must comply with the submission requirements as outlined. Submittals that fail to comply with the requirements as specified may be deemed non-responsive and such determination will result in no further consideration of that respondent or the respondent’s submittals by the Client. At any stage, the Client reserves the right to terminate, suspend or modify this selection process; reject any or all submittals at any time; and waive any informalities, irregularities or omissions in submittals, as the best interests of the Client may require.

1.8 PROPOSAL REQUIREMENTS

Proposals must include, but are not limited to, the following items:

Part 1 – Organization Information

A. Brief cover letter expressing interest.

B. If your firm has multiple offices, please provide this information for all offices. Indicate which office is going to perform the bulk of the services for this project.

C. Statement of available bonding capacity for this project.

D. Completed AIA A305 including financial statements (as attachment)

E. A copy of your current certificate of insurance for professional liability.

F. Statement of Conflicts of Interest (if any) the service provider or key employees may have regarding these services, and a plan for mitigating the conflict(s). Note that City/County may in its sole discretion determine whether or not a conflict disqualifies a firm, and/or whether or not a conflict mitigation plan is acceptable.

G. Form Conflict of Interest Questionnaire. Texas Local Government Code chapter 176 requires that any vendor or person who enters or seeks to enter into a contract with a local government entity disclose in the Questionnaire Form CIQ the vendor or person’s employment, affiliation, business relationship, family relationship or provision of gifts that might cause a conflict of interest with a local government entity. Questionnaire form CIQ is included in the RFQ and must be submitted with the response.

H. Certification Regarding Lobbying- Disclosure of Lobbying Activities. Certification for Contracts, Grants, Loans, and Cooperative Agreements is included in the RFQ and must be submitted with the response.

I. Form 1295. Effective January 1,2018, all contracts and contract amendments, extensions, or renewals executed by the Commissioners Court will require the completion of Form 1295 “Certificate of Interested Parties” pursuant to Government Code § 2252.908. Form 1295 must be completed by the awarded vendor at time of signed contract submission. Form 1295 is included in this RFQ for your information. Form 1295 requires the inclusion of an “unsworn declaration” which includes, among other things, the date of birth and address of the authorized representative signing the form.

Part 2 – Project Experience

A. Present at least three (3) DESIGN BUILD projects completed within the last five (5) years that are similar in size, function, security requirements, and complexity. Preference will be given to experience involving jails, detention/correctional facilities, law enforcement facilities, secure occupied facilities, phased construction, and renovation/additions performed while the facility mailto:danya.lewis@grimescountytexas.gov

Page 11 of 23 Grimes County Design-Build RFQ remained operational. Include:

1) Project location

2) Project size (square feet) of the project

3) Project completed construction value

4) Project construction start and completion date

5) Method of construction

6) Other relevant project information, including number of detention beds where applicable;

scope of renovation, expansion, or new construction; security/detention systems; phasing;

operational-continuity challenges; and non-destructive testing or existing-condition investigation performed.

7) General Contractor Staff directly involved with the project. Identify teams Preconstruction Manager, Project Manager, Estimator and Superintendent at a minimum

8) Client/Owner contact with telephone number

9) Owner’s Representative contact with telephone number

10) Architect contact with telephone number

Part 3 – Project Team & Staff

A. Resumes for:

1) Architect

2) Landscape Architect

3) Engineers

4) Estimator

5) Project Manager

6) Project Superintendent

B. Owner and other references (including telephone numbers and email), to clearly identify which project and who the reference is in relation to. Please include relevant projects team members that have worked on together.

C. Describe current workload of proposed staff and overlapping project responsibilities.

D. Provide an organization chart graphically indicating how your firm would staff and structure the proposed team (both in the field and in the office) during the Pre-Construction and Construction phases.

E. Provide a matrix showing what projects you have worked on with the team designers.

Part 4 – Organization & Management of the Project

A. Describe what makes your team’s Design Build service unique and successful.

B. Describe what makes your firm’s design and pre-construction services unique. What tools do you use to enhance the process? Describe your approach.

C. Describe how your cost estimating process is organized and provide specific examples of your cost estimating documents where you feel such information will provide clarity. Provide historical cost comparisons between schematic design cost estimates and the final GMP on projects of similar size and/or scope to that of the project.

D. Describe your approach to safety, security, and construction logistics for work occurring within or adjacent to a continuously operating detention/law enforcement facility. Address contractor access, inmate/staff/public separation, secure barriers, tool and material control, deliveries, utility interruptions, emergency access, and coordination with facility personnel. Cite specific examples where your team successfully managed comparable conditions.

E. Describe how your Design-Build team recently resolved a complicated or unexpected existing-

Page 12 of 23 Grimes County Design-Build RFQ condition issue on a renovation/addition project, including the investigation or non-destructive testing used, the effect on operations, and how cost and schedule impacts were managed.

F. Describe a recent Design-Build jail, detention, law enforcement, or other secure occupied-facility project. Identify lessons learned that would be directly applicable to this Project, particularly regarding phasing, security, detention systems, and maintaining operations.

G. Have your superintendent describe what he/she is most proud of on his/her most recent project.

H. What bothers your superintendent most on projects and how does he/she resolve it?

I. Have your project architect summarize what is most important when planning an addition, renovation, and/or new construction project at an active detention and law enforcement facility.

J. Fill in the blank: We define success on a project as .

Part 5 – Fee Proposal

A pricing line-item sheet is included in this document as an outline of the anticipated project cost categories. Fees are not due with this initial qualifications submission but will be required during the interview/fee proposal phase if your team reaches that stage.

• Insurance certificates naming the Client as additional insured will be required prior to work commencing, but not required as part of this submittal.

1.9 QUESTIONS, INQUIRIES, AND AMENDMENTS REGARDING THIS RFQ

Questions and inquiries regarding the RFQ should be directed to the Project Manager listed above by the date aforementioned. The Client will issue a response to all questions by email.

Questions should not be submitted to the Client, the Board or other parties, doing so will cause this candidate’s removal from the RFQ process.

1.10 DESIGN BUILDERS TO FULLY INFORM THEMSELVES

DESIGN BUILDERS are required to fully inform themselves of all project conditions which may impact their proposal and the Client’s requirements prior to submitting a proposal. Proposers should become acquainted with the nature and extent of the services to be undertaken and make all necessary examinations, investigations and inspections prior to submitting a proposal. Firms proposing are responsible for examining and determining for themselves the location and nature of the proposed work, the amount and character of the labor and materials required, and the difficulties which may be encountered. If requested in advance the Client will provide the Firm proposing access to the site to conduct such examinations as each Proposing Firm deems necessary for submission of a proposal. The Proposing Firm is to consider federal, state and local Laws and Regulations that may affect cost, progress, performance or furnishing of the Work. The Client will not consider any claims arising from failure to take such actions.

1.11 EVALUATION & SELECTION CRITERIA

The Client reserves the right to reject any or all responses to this RFQ. Final selection of the short-listed DESIGN BUILD candidates will be on the basis of their apparent ability to best meet the overall expectations of the Client, as determined solely by the Client.

The Client reserves the absolute right to conduct investigations as it deems necessary for the evaluation of any proposal and to establish the experience, responsibility, reliability, references, reputation, business ethics, history, qualifications and financial ability of the firm responding. The purpose of such investigation is to determine that the DESIGN BUILD has the ability, experience, resources and reputation necessary to perform the work and to support all warranties in accordance with the contract documents. The following items will be reviewed to provide a basis for selection, (not in order of priority):

Page 13 of 23 Grimes County Design-Build RFQ

A. Qualifications Proposal Phase of Selection (total points available = 100):

Criteria Maximum Points

Experience 60

Work Performance 25

Capacity to Perform 15

Total 100

The Rating Sheet that will be used for scoring is provided on the next page.

Page 14 of 23 Grimes County Design-Build RFQ

DESIGN BUILDER Rating Sheet

Name of DESIGN BUILDER: _______________________ Evaluator's Name: _______________________ Date of Rating: __________

Rate the Respondent of the Request For Qualifications (RFQ) by awarding points up to the maximum listed for each factor. Information necessary to assess the Respondent on these criteria may be gathered either from past experience with the Respondent and/or by contacting past/current clients of the Respondent. Respondents proposing to offer specific services (environmental or buyout only) will be scored only on those services.

Experience -- Rate the respondent for experience in the following areas: Comments

Factor Max Pts Score

1. Has previously designed jail, detention/correctional, law enforcement, or comparable secure-facility projects

2. Has completed phased renovation/expansion or new construction adjacent to an operating secure facility

3. Has worked on projects that were located in this general region.

Note: Location for A/E (Architect/Engineer) may be a selection criterion provided its application leaves an appropriate number of qualified firms, given the nature and size of the project, to compete for the contract. 2 CFR 200.321(b)(3)

4. Extent of experience in Design-Build construction management for detention/law enforcement or comparable secure projects

Subtotal, Experience 60

Work Performance

1. Past projects completed on schedule 10

2. Manages projects within budgetary constraints 5

3. Work product is of high quality 10

Subtotal, Performance 25

Capacity to Perform

Page 15 of 23 Grimes County Design-Build RFQ

1. Staff Level / Experience of Staff 5

2. Adequacy of Resources 5

3. Professional liability insurance is in force 5

Subtotal, Capacity to Perform 15

TOTAL SCORE

◻ Experience 60

◻ Work Performance 25

◻ Capacity to Perform 15

Total Score 100

Page 16 of 23 Grimes County Design-Build RFQ

B. Interview & Fee Proposal Phase of Selection:

1) Those respondents deemed best qualified will be invited to participate in an interview with the Selection Committee. An interview invitation will be sent out to approx. three (3) Candidates with the highest RFQ submittal scores (from the above Qualifications Proposal Phase) on the date noted in the schedule of events. The invitation will explain the interview requirements and provide the time and location. The purpose of the interview is to ensure a full understanding of the RFQ responses, and to introduce key members of the DESIGN BUILD Team.

2) Each shortlisted firm will be required to complete and submit a DESIGN BUILD Fee and Schedule Proposal Form (including fees) on the date noted in the schedule of events. This information will be evaluated and rated in terms of responsiveness and value.

❖ Note – Although the project cost will be a major component of the selection process, other factors will also be considered. Contract may not be awarded to the DESIGN BUILDER providing the lowest proposed fee.

1.12 SELECTION PROCESS

A. The Client will review all responses to this RFQ that meet requirements and are received prior to the designated closing date and time.

B. Upon review of the qualified firms, the Client will select the proposal which best reflects the Client’s needs and requirements.

C. The top firm’s proposal, based on qualifications, will be reviewed and, if necessary, negotiations will commence.

D. If a satisfactory agreement with the DESIGN BUILDER cannot be reached, at a price that is determined to be fair and reasonable, negotiations with that firm shall be formally terminated.

Negotiations with the second ranked proposer may then be initiated. Failing accord with the second ranked proposer, the Client shall formally terminate negotiations and may then undertake negotiations with the third ranked proposer or re-issue the RFQ at their discretion.

E. The Client will have sole determination of which proposal is in the Client’s best interest.

1.13 RIGHT OF REJECTION

The Client reserves the right to accept or reject any or all responses to this RFQ and to enter into discussions and/or negotiations with one or more qualified DESIGN BUILDERS, if such action is in the best interest of the Client. The Client has the right, in its sole and absolute discretion, to select the proposal or proposals that the Client determines best meets its needs.

1.14 MODIFICATION AND WITHDRAWAL OF PROPOSAL

A. Withdrawn proposals may be resubmitted up to the time designated for the receipt of proposals due date/time provided that they are then fully in conformance with the RFQ.

B. If, within twenty-four hours after proposals are opened, any company that provides written notice to the Client and promptly thereafter demonstrates to the reasonable satisfaction of Client that there was a material and substantial mistake in the preparation of its proposal, that company may withdraw its proposal. Thereafter, that company will be disqualified from further bidding on the Work.

1.15 PROPOSALS TO REMAIN OPEN SUBJECT TO ACCEPTANCE

All proposals shall remain open for forty-five (45) days after the day of the proposal opening, but the Client may, in its sole discretion, release any proposal prior to that date.

1.16 COST OF PROPOSALS

Page 17 of 23 Grimes County Design-Build RFQ

Expenses incurred in the preparation of proposals in response to this RFQ are the DESIGN BUILDER’s sole responsibility. The Client assumes no responsibility for payment of any expenses incurred by any Proposing Firm as part of the RFQ process.

Page 18 of 23 Grimes County Design-Build RFQ

2.0 PROPOSAL FORM

2.1 PROPOSAL FORM FOR DESIGN BUILD

(Please use additional sheets as necessary.)

COMPANY NAME:

COMPANY ADDRESS:

PHONE: FAX:

CONTACT PERSON NAME:

CONTACT PERSON PHONE:

CONTACT PERSON EMAIL:

1. I Acknowledge that the “Sample Agreement” attached to this RFQ has been reviewed and is agreed to as shown. (YES/NO). Do you request amendments to the “Agreement” (YES/NO) Please list them if yes.

2. Acknowledgment that the submitting agent meets or exceeds insurance requirements as outlined in the RFQ. (YES/NO)

3. The undersigned Proposer declares and stipulates that this proposal is made in good faith, without collusion or connection with any other person or persons bidding for the same Work, and that it is made subject to all the terms and conditions of the Request for Proposal and associated documents, all of which have been examined by the undersigned. (YES/NO)

4. The submission of the proposal constitutes an agreement and shall not be withdrawn after the proposal opening for a period of forty-five days.

5. Acknowledgment that the submitting agent carries (or will carry) a license in Grimes County, Texas

_____ (YES/NO)

6. List of construction items that will be self-performed.

A I

B J

C K

D L

E M

F N

G O

H P

Signature: Date:

Page 19 of 23 Grimes County Design-Build RFQ

3.0 ATTACHMENTS

3.1 EXHIBIT A: PRELIMINARY SITE CONDITIONS / PROJECT INFORMATION

3.2 EXHIBIT B: DESIGN BUILD AGREEMENT, STANDARD AIA A141

To be provided by DESIGN BUILDERS at time of contract

Page 20 of 23 Grimes County Design-Build RFQ

3.3 EXHIBIT C: PRICING LINE-ITEM SHEET

Grimes County Law Enforcement Center Expansion / New Construction

Civil $___________________/sq ft

Structural $___________________/sq ft

Architectural $___________________/sq ft

Electrical $___________________/sq ft

Mechanical $___________________/sq ft

Plumbing $___________________/sq ft

Site Work / Civil Improvements

$___________________/s q ft

CONSTRUCTION MANAGEMENT FEE $___________________/sq ft

CONTRACTOR’S CONTINGENCY (________ %) $_______________________

P & P BONDS $_______________________

SUBTOTAL $___________________/sq ft

CONSTRUCTION PROFIT (______ %) $______________________

Proposed Fixed Project Construction Budget $___________________/sq ft

Architect fees $______________________

Engineer fees $______________________

PROPOSED CONTRACT PRICE $______________________

PROPOSED CONSTRUCTION DURATION/COMPLETION: _________ calendar days from Notice to Proceed

Page 21 of 23 Grimes County Design-Build RFQ

Page 22 of 23 Grimes County Design-Build RFQ

Page 23 of 23 Grimes County Design-Build RFQ

File details come from the government source that posted it. Updated .