The file's text, extracted by GovTribe without its formatting.
Request for Information
N64498-27-SIMACQ-PD-42-0026
Model M250-KS4 Gas Turbine Engineer Special Support Equipment (SSE) Requirement Description/ Draft Scope The Naval Surface Warfare Center, Philadelphia Division is hereby issuing a Request for Information (RFI) from all potential sources to provide information regarding a commercial, modified commercial, or non-commercial product/service solution(s) to the below specifications:
The Naval Surface Warfare Center, Philadelphia Division requires procurement of seven (7) sets of 250-KS4 gas turbine engine Special Support Equipment (SSE) from Boeing Distribution Company (BDI). This SSE will provide Regional Maintenance Center turbine shops with maintenance capabilities which will significantly reduce repair turnaround times and enable the refurbishment of previously unusable carcasses. This equipment is critical for operational and mission readiness. This procurement of the M250-KS4 SSE will increase the amount of RFI assets available to the Navy.
Description of Supplies: 250-KS4 SSE
Part Number(s): See table below
| Part Number |
| Description |
| Quantity |
| 23089393 |
| STAND: MAINTENANCE, ENGINE |
| 7 |
| 23055346 |
| TOOL: WRENCH,5/16IN BX |
| 7 |
| 6799790 |
| ADAPTER: ENGINE TURNING |
| 7 |
| 6795588 |
| TOOL: WRENCH, HOLDING,32/64 PIT |
| 7 |
| 6795984 |
| HOLDER-POWER TURBINE SHAFT |
| 7 |
| 6795985 |
| WRENCH: POWER TURBINE,SHAFT |
| 7 |
| 6795990 |
| DUMMY BEARING-POWER TURBINE SH |
| 7 |
| 6795992 |
| DUMMY BEARING-GAS PRODUCER TUR |
| 7 |
| 6796920 |
| PULLER-OIL JET: GAS GENERATOR |
| 7 |
| 6798928 |
| PROTECTOR-POWER TURBINE OIL BE |
| 7 |
| 6799973 |
| PULLER: SEAL,POWER TURBINE |
| 7 |
| 6872882-5 |
| RING: PULLER,TURBINE FRONT #5 BEARING |
| 7 |
| 23003262 |
| CRIMPER-LOCKNUT: GASIFIER TURB |
| 7 |
| 23083902 |
| TOOL: INSTALL,#5 BEARING |
| 7 |
| 6872543 |
| FIXTURE: INSTALLATION, PRESS |
| 7 |
| 23090699 |
| GAUGE: GO-NO-GO |
| 7 |
| 6795966 |
| FIXTURE: COMPRESSOR ASSEMBLY |
| 7 |
| 6798796 |
| DRIFT-DAMPER VIBRATION: COMPR |
| 7 |
| 6799700 |
| PULLER-VIBRATION DAMPER: FRONT |
| 7 |
| 6872534 |
| FIXTURE: ALIGNING,ROTOR |
| 7 |
| 6893535 |
| TOOL: REMOVAL, RETAINING RING |
| 7 |
| 23089389 |
| HOLDER: CARBON SEAL |
| 7 |
| 23005023 |
| TOOL: PULLER,BEARING & SEAL |
| 7 |
| 6799955 |
| FIXTURE: TURBINE ASSEMBLY |
| 7 |
6895538 (Replaces 6799959, 6799959-6 & 6799959-7)
| TOOL: PRESS, SEAL/BEARING |
| 7 |
| 6799955-6 |
| WRENCH RETAINER |
| 7 |
| 23083912 |
| TOOL: PULLER, LIP SEAL |
| 7 |
| 23083918 |
| TOOL: PUSHER, LIP SEAL |
| 7 |
Submission of Responses:
Vendors are requested to provide brochures, literature and/or information on their supply/service.
Vendors are further required to provide the following information:
a.) Company name, address, phone number, primary contact(s), email address, ALL applicable NAICS code(s), business size (i.e., small/large), company's socioeconomics (i.e., woman-owned, Service Disabled Veteran Owned, HUBZone, 8(a), etc.) and DUNS Number.
b.) Current products that are capable of meeting requirements.
c.) Typical capabilities included.
d.) User(s) location and representative that agency may contact to discuss the product(s) e.) Equipment origin or place of manufacture.
f.) User(s) location and representative that agency may contact to discuss the product(s).
g.) Warranty information.
h.) Any other information needed/provided from Customer.
Anticipated Contract Type (if known):
RFI Point of Contact:
Jenny Tomeo Jenny.e.Tomeo.civ@us.navy.mil
Response Date: 09 October 2026 06:00PM EST
NOTE: THE PROVIDED INFORMATION SHALL NOT EXCEED MORE THAN TEN PAGES IN LENGTH.
DISCLAIMER: this RFI is for informational/planning purposes only. This is not a request for quote/proposal. It does not constitute any form of solicitation and shall not be construed as a commitment by the government. Responses in any form are not offers and the government is under no obligation to make any form of award as a result of this announcement. No funds are available to pay for preparation of responses to this announcement. Any information submitted by respondents to this RFI is strictly voluntary.
All information received in response to this rfi marked “proprietary” will be safegarded and handled accordingly. Interested parties are responsible for adequately marking proprietary or competition sensitive information that is contained in their response
