R.Yered SOW Annual Hull Service.pdf

STATEMENT OF WORK

CGC ROBERT YERED (WPC 1104)

Diver Hull Clean, Inspect & Zinc Anodes Renewal

FSMS PR# 52000PR260027553

Description of Services:

Contractor travel to CGC ROBERT YERED homeport in Miami, FL to perform cleaning and inspection of underwater hull and running gear (appendages), polish PORT and STBD propellers, renewal of government-furnished zinc anodes/hardware, provide inspection report, before/after video and photographs IAW MPC's B10015.D and B10018.D.

Period of Performance:

Cutter availability is 01 September 2026-14 September 2026 (scheduling to be arranged with cutter POC)

Performance Location:

USCGC ROBERT YERED (WPC 1104)

100 MACARTHUR CSWY

Miami, FL 33139

Cutter Contact Info:

EPO: MKC Jordan T. Pearson Email: Jordan.T.Pearson@uscg.mil

PH: (850) 234-2377

Requisitioner Contact Info:

SFLC-PBPL-APM: CWO Michael Hardy Email: Michael.R.Hardy@uscg.mil

PH: (206) 815-2340

IPP Approver Contact Info:

SFLC-PBPL-Section Chief: LT Alexandra Lombardi Email: Alexandra.P.Lombardi@uscg.mil

PH: (781) 715-5683

Security Requirements:

All contractor personnel requiring access to the place of performance in order to perform work under this contract must possess a valid-state issued REAL ID-compliant driver’s license or identification card, or an acceptable alternative form of identification as defined by the Department of Homeland Security (DHS) [https://www.dhs.gov/real-id]. It is the contractor’s responsibility to ensure that all personnel are properly credentialed to gain base access. Failure to comply with access requirements may result in delays to performance and will not constitute an excusable delay

U/W Body (Waterborne), Diver Hull Clean, Inspect, & Zinc Anodes Renewal

1. Scope

1.1 Intent. This work item describes the requirements for the Contractor to clean and inspect the vessel’s underwater (U/W) body, and to renew bolt-on zinc anodes, while the vessel is moored pier side.

1.2 Government-furnished property.

MTI ITEM DESCRIPTION NSN/PN QTY

N Anode, Stern Tube NSN: 5340-01-644-5483

PN: Z0020202H3

28 ea.

N Nut, Self-Locking NSN: 5310-01-508-5774

PN: 90715A145

3 pkg.

*25 in pkg.

N Anode, Sea Chest Grate NSN: 5340-01-647-6179

PN: GA-4

4 ea.

N Screw, Prop Zinc Plate NSN: 5305-01-634-0210

PN: 950756

8 ea.

N Screw, Sea Chest Grate Anode

NSN: 5305-01-619-7182

PN: 93190A634

1 pkg.

*5 in pkg.

N Screw Cap, Stern Tube Covers

NSN: 5305-01-616-1107

PN: 90585A626

42 ea.

N Zinc Plate, Propeller NSN: 5340-01-627-8941

PN: 950733

2 ea.

N Anode, Bow Thruster, Gear Case, Bolt On

NSN: 5342-12-356-1870

PN: 1081226

1 ea.

N Anode, Bow Thruster, Tunnel, Bolt On

NSN: 5340-20-012-6334

PN: CM2000Z

12 ea.

2. REFERENCES

COAST GUARD DRAWINGS

Coast Guard Drawing 154 WPC 111-301, Rev B, Shell Expansion

Coast Guard Drawing 154 WPC 161-301, Rev C, Skegs and Stern Tubes Support Structures

Coast Guard Drawing 154 WPC 245-304, Rev B, Propeller Plans and Data Six Blade Propeller

Coast Guard Drawing 154 WPC 562-201, Rev A, Rudder Details

Coast Guard Drawing 154 WPC 565-201, Rev -, Fin Stabilizer System A & D

Coast Guard Drawing 154 WPC 568-201, Rev B, Bow Thruster System A & D

Coast Guard Drawing 154 WPC 997-302, Rev -, Docking Plan

COAST GUARD PUBLICATIONS

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General Requirements

Surface Forces Logistics Center Maintenance Procedure Card B10015.D (MPC B10015.D), 10/31/24, Underwater Body and Appendages Inspect/Clean (Diver)

Surface Forces Logistics Center Maintenance Procedure Card B10018.D (MPC B10018.D), 4/30/25, Underwater Zinc Anode Replace

OTHER REFERENCES

None

3. REQUIREMENTS

3.1 General.

3.1.1 CIR. None.

3.1.2 Tech Rep. None.

3.1.3 Protective measures. The Contractor must furnish and install all protective measures in accordance with SFLC Std Spec 0000, paragraph 3.3.3 (Vessel component, space, and equipment protection).

3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences).

3.2 Requirements. The Contractor must:

3.2.1 Video recording/photographs. Submit video highlights and photographs of all underwater body surfaces and appendages (e.g. bow thruster, propellers, rudders, fin stabilizers, transducers, sea chests, heavily fouled hull areas, etc.) before and after cleaning.

3.2.2 Clean/inspect. Clean the underwater body surfaces and appendages free of all marine growth, debris, and all other surface contaminants, to include inspections in accordance with MPC B10015.D.

Polish the surfaces of both PORT and STBD propellers. Ensure all transducer surfaces are cleaned with only soft hand held brushes, without the use of power attachments. Ensure that existing underwater body coating system or non-coated surfaces do not incur any damage during cleaning process. Refer to Coast Guard drawings listed in Section 2.

3.2.3 Renew anodes. Renew Government-furnished components listed below paragraph 1.2. in accordance with MPC B10018.D.

4. NOTES

This section is not applicable to this work item.