QA033 - Testing Requirements.pdf

HC101325QA033 - TESTING REQUIREMENTS

THIS REQUIREMENT MUST BE ENGINEERED AND PROVISIONED TOTALLY DIVERSE END

TO END TO GOVERNMENT'S SERVICE DELIVERY POINTS (SDP'S) FROM TSR

RU17SEP249070, MEANING THAT PHYSICAL PATHS ARE TOTALLY SEPARATE INCLUDING

MANHOLES, CONDUIT, (CENTRAL OFFICE LOCATIONS), AND FIBER BUILDS. ADDITIONALLY,

AS A MINIMUM THERE MUST BE A 50 METER PHYSICAL SEPARATION FROM CJON:

SF18SEP249071. ***THE 50 METER SEPARATION IS WAIVED INSIDE BLDG 2201 FOR WASH

DOS LOCATION.***

THE TELECOM PROVIDER MUST PROVIDE DITCO COLOR POWERPOINT DRAWINGS FOR

TECHNICAL REVIEW SHOWING THE ROUTES FROM THE COMMERCIAL DEMARCS TO THE

SUPPORTING CENTRAL OFFICES AND/OR WIRING CENTERS. DRAWINGS MUST INCLUDE

SEPARATION DISTANCES BETWEEN DIVERSE REQUIREMENTS, TOTAL FIBER MILES, AND

ROUND-TRIP DELAY (RTD), AND FIBER ROUTES RED LINED END TO END SO THE

GOVERNMENT CAN CONFIRM PHYSICAL END TO END DIVERSITY REQUIREMENTS ARE

MET. ADDITIONALLY, THE VENDOR IS TO PROVIDE DITCO WITH DETAILED CIRCUIT/PATH

CONNECTIVITY DIAGRAMS, IN KMZ OR KML FORMAT, IDENTIFYING ALL POINTS OF

PRESENCE (POP) FOR EVALUATION AND AS A FINAL RECORD OF THE INSTALLED PATH.

THESE DIAGRAMS MUST BE PROVIDED TO DISA HQ IE16 (DISA.MEADE.IE.MBX.IE16-

PROVISIONING-TEAM@MAIL.MIL) FOR HISTORICAL PURPOSES.

THE VENDOR MUST TERMINATE 10GB, NON-SWITCHED ETHERNET SERVICE AT SERVICE

DELIVERY LOCATIONS, IAW UNIQUE INSTALLATION FACTORS.

THE VENDOR MUST CONDUCT WALK-THROUGH SITE SURVEY PRIOR TO INSTALLATION AT

BOTH LOCATIONS.

THE VENDOR MUST CONDUCT A SATISFACTORY 24-HOUR TEST FROM THE DROP SIDE OF

THEIR FIBER DISTRIBUTION POINT (FDP) INSTALLED IN THEIR EQUIPMENT SUITE AT THE

"A" LOCATION TO THEIR FDP INSTALLED IN THEIR EQUIPMENT SUITE AT THE "Z" LOCATION

AND MUST INCLUDE THE EXTENSION BETWEEN THE COMMERCIAL DEMARC AND THE

GOVERNMENT'S SDP. A SATISFACTORY TEST MUST BE ACCOMPLISHED PRIOR TO TURN-

OVER TO THE GOVERNMENT FOR ACCEPTANCE TESTING. THE VENDOR MUST TEST THE

CIRCUIT FOR 24 HOURS IAW THE FULL ITU-T.Y.1564 BENCH MARKING METHODOLOGY FOR

NETWORK INTERCONNECT DEVICES STANDARD, AND AT THE COMMITTED INFORMATION

RATE (CIR) IAW ITU-T-Y.1564.

THE VENDOR MUST CONTACT DISA GOC TIER-II ENGINEERING 48 HOURS PRIOR TO

BEGINNING THEIR END-TO-END TESTING. PHONE: (C) 618-418-8627, (D) 418-8627.

CIRCUIT REQUIRES THE FOLLOWING PARAMETERS:

(A) FIBER TERMINATION: FRAME FORMAT: 10GB, ETHERNET (OPTICAL HANDOFF-10GB

ETHERNET-LAN-PHY-SINGLE MODE FIBER), 1310NM. "SC" OR "LC" CONNECTORS AS

DETERMINED BY SITE SURVEY. NOTE: WHEN EXTENDED REACH OPTICS ARE USED THAT

CHANGE THE TX/RX WAVELENGTH OF THE OPTIC, THE VENDOR WILL NOTIFY THE

GOVERNMENT 30 DAYS PRIOR TO DELIVERY.

(B) THE VENDOR MUST PROVIDE LIGHT LEVEL READINGS (SIGNAL STRENGTH IN DBM) ON

THE EXTENSION FROM COMMERCIAL POP TO THE GOVERNMENT SERVICE DELIVERY

POINT (SDP) AT THE "A" AND "Z" LOCATION PRIOR TO CIRCUIT TURN-OVER TO THE

GOVERNMENT ENSURING LEVELS ARE WITHIN SPECS. LIGHT LEVELS MUST BE ADJUSTED

TO -7 TO +0.5DBM COMPOSITE.

(C) THE COMMITTED INFORMATION RATE (CIR) (9884.9 MBPS) REQUIRES THE VENDOR TO

DELIVER A 10GB ETHERNET LAN-PHY INTERFACE AT THE DROP SIDE OF THE

COMMERCIAL DEMARCS AT THE "A" AND "Z" LOCATIONS.

(D) ETHERNET FRAME SIZE WILL BE CONFIGURED TO SUPPORT MAXIMUM TRANSMISSION

UNIT (MTU) OF 9000 OCTETS (BYTES) JUMBO FRAMES.

(E) MACSEC REQUIREMENT: ETHERNET LEASED CIRCUIT OF ANY SPEEDS (E.G.,1G, 10G,

OR 100G) MUST SUPPORT PORT-BASED MACSEC OR VLAN-IN-THE-CLEAR MACSEC

SPECIFICALLY BY PASSING ALL ETHERTYPE FRAMES INCLUDING MACSEC CONTROL

TRAFFIC MKA ETHERTYPES (0X888E AND 0X876F) AND MACSEC FORWARDING TRAFFIC

ETHERTYPE (0X88E5). ALL VENDOR IN-LINE PROVISIONING DEVICES/PLATFORMS OF THE

ENTIRE CIRCUIT MUST SUPPORT PASSING ALL LAYER 2 ETHERNET FRAMES INCLUDING

FRAMES WITH MACSEC 802.1AE HEADER AND MUST NOT BLOCK, DROP, OR CONSUME

ANY FRAME.

(F) GFE CLOCKING: VENDOR ESFU (OR EQUIVALENT) NOT TO BE ENGINEERED INTO

CIRCUIT.

(G) THE VENDOR WINNING THE AWARD IS RESPONSIBLE FOR INSTALLATION AND

MAINTENANCE OF THE SERVICE IAW THE UNIQUE INSTALLATION FACTORS.

(H) INSIDE WIRING IS AUTHORIZED IAW THE UNIQUE INSTALLATION FACTORS.

(I) THE VENDOR MUST MAINTAIN 24X7 OPERATIONS, MAINTENANCE, AND

ADMINISTRATION MONITORING OF ETHERNET CIRCUIT IAW ITU-T Y.1731. THE CIRCUIT

MUST REMAIN FULLY OPERATIONAL AND AVAILABLE TO USERS 24 HOURS A DAY, SEVEN

DAYS PER WEEK. MONTHLY PERFORMANCE AVAILABILITY SHALL BE 99.5% OR BETTER.

(J) THE VENDOR MUST MAINTAIN A 1 HOUR RESPONSE TIME UPON RECEIPT OF A

CUSTOMER REPORTED TROUBLE.