PWS - 110 WG LTS 2025-1.pdf

PERFORMANCE WORK STATEMENT (PWS)

Local Telecommunication Services (LTS) Conversion from LSTDM to SIP Trunking

Battle Creek ANGB, MI

DATE: 30 Jan 2025

TABLE OF CONTENTS

1. INTRODUCTION

1.1. Objective

1.2. Background

2. SCOPE

2.1 Outages

2.2. Services Summary

3. GOVERNMENT PROVIDED SPACE & SERVICES

3.1. Securing and Safeguarding

3.2. Rack Space

3.3. Environmental Controls

3.4. Wall Space

4. GENERAL REQUIREMENTS

4.1. Personnel

4.2. Government Emergency Telecommunications Service (GETS)

4.3. Interconnection Agreements, and Cutover Plans

4.4. Safety, Health and Fire Protection Requirements

5. ACCESS & GENERAL PROTECTION/SECURITY POLICY & PROCEDURES

5.1. Contractors Requiring Common Access Card (CAC)

5.2. Contractors That Do Not Require Common Access Card (CAC)

6. APPENDICES

APPENDIX 1 – SITE SPECIFIC REQUIREMENTS

APPENDIX 2 - DEFINITIONS & ACRONYMS

1. INTRODUCTION

1.1. Objective

This requirement will re-home existing Local Telecommunication Services (LTS) that are currently provided on a low-speed time-division multiplexed (LSTDM) circuit with one provided using session initiation protocol (SIP) trunks. All connectivity requirements and features currently transported over the existing LSTDM must be migrated over so that transition can occur without any loss of capability. This PWS is for unmanaged SIP trunks.

Battle Creek ANGB has a private branch exchange (PBX), so managed PBX is out of scope. Current PBX is not capable of supporting SIP trunks and will require the use of a managed switch/media converter provided by the servicing vendor. Once the PBX is upgraded in the future, this switch will be removed and any associated recurring monthly costs (MRC) will be dropped. This LTS will support the installation 24 hours a day/seven days a week/365 days a year (24/7/365).

1.2. Background

The Department of Defense (DoD) Chief Information Officer (CIO) has mandated all LSTDM transport technologies used for mission-related tasks be retired and replaced with IP based technologies. This is due to commercial support and hardware for LSTDM equipment being more difficult to find or phased out entirely. LTS does not include Defense Switching Network (DSN) services, which are beyond the scope of this action.

Due to changes in technology, equipment, and processes, it has become evident that the Government should acquire these services in a performance-based manner, consistent with the principles contained in Air Force Instruction (AFI) 63-138 “Acquisition of Services.” These services are considered Information Technology (IT) In Accordance With (IAW) Defense Federal Acquisition Regulation Supplement (DFARS) 239.74 “Telecommunications Services.” The requirement herein represents the site’s performance-based requirements for local “dial-tone” and ancillary services as defined herein. As a part of the new process, the Air Force (AF) encourages the Contractor to identify or suggest improvements to existing LTS processes, operating procedures, systems, or applications to the Contracting Officer (CO).

2. SCOPE

The Contractor shall provide all labor, tools, facilities, materials, and services needed to perform and provide local access to the designated circuit demarcation point(s) identified in Appendix 1 to this PWS. These services shall include any equipment, wiring, or infrastructure to ensure the Contractor’s proposed solution is compatible with the Government’s current infrastructure without additional Government expense. Access to the local exchange shall also include operator assistance functions. These services shall not include residential or business services for non-Government entities or Government contractors. The Contractor shall follow all Federal Communications Commission (FCC), Public Utility Commission (PUC), Department of Defense (DoD), AF, and industry standards for this requirement.

The Contractor shall provide and install transmission equipment and cables for local exchange access and transport service circuits to the Government-provided floor space at the Government demarcation location(s) identified in Appendix 1. The Contractor shall connect to Government-provided power connection points and termination frames. The Contractor shall coordinate with the Government Point of Contact (POC) (primary and alternate names, emails, and telephone numbers shall be provided by the Government No Later Than (NLT) five days after contract award) prior to any installation. The Government does not authorize aerial cable installations.

2.1 Outages

2.1.1. Scheduled Outage. The Contractor shall notify the Government POC of any scheduled outage that will affect any telecommunication service. The Contractor shall inform the Government POC NLT 30 days prior to the scheduled outage. The Contractor shall provide a detailed explanation for the outage to include the amount of downtime and end users affected. The Contractor shall notify the Government POC via email of the need for any scheduled service outages. Such outages shall be scheduled to minimize inconvenience to users. The Government POC must release all affected equipment and circuits prior to any service disruption. The Contractor shall follow procedures identified below for outages. In all cases, notification shall include:

• Reason for interruption

• Duration

• Start and stop times

• Affected equipment, lines, and buildings

• Restoration action (what service was impacted and how service was restored)

2.1.2. Unscheduled Outages. If multiple facilities, areas, primary trunks, or cables/fibers are impacted, the Communications Focal Point (CFP) and Government POC shall assign the category of the outage and establish the repair priority. The Contractor shall notify the CFP and Government POC verbally of problem(s) and follow-up with documentation via email within time specified for each outage type.

2.1.3. Outage Procedures. The Contractor shall follow procedures identified below for outages. In all cases, notification shall include:

Reason for interruption Duration Start and stop times Affected equipment, lines, and buildings Restoration action (what service was impacted and how service was restored)

2.1.4. Outage Priority, Restoration of Service, and Maintenance. The Contractor shall respond and restore service outages. From the time of receipt of the notification, the Contractor shall respond and coordinate with the Government POC within the time limits indicated below. For mission-essential functions, the Government POC shall identify and prioritize the essential contractor services. The Contractor shall prioritize and perform restorations IAW the Telecommunications Services Priority (TSP) and Restoration Priority List (RPL), which are provided by the Government POC. In the event that the Contractor anticipates not being able to perform any of the essential contractor services (i.e. beyond the Contractor’s control) IAW the TSP and RPL during a crisis situation, the Contractor shall notify the Government POC as expeditiously as possible and use its best efforts to cooperate with the Government in the Government’s efforts to maintain the continuity of operations. If the Government POC determines that the outage restoration time frames cannot be met for other non-mission essential functions, the Government POC can declare any outage restoration priority level as catastrophic to emergency to serious to routine if the outage significantly affects the mission of the Government.

2.1.4.1. High Priority Outage. A high priority outage is normally a sudden and widespread disaster stemming from the result of a man-made or natural disaster in which property, equipment, and site infrastructure are completely destroyed. The Contractor shall respond onsite to the outage NLT one hour of receipt of notification by the CFP or Government POC and advise the CFP and Government POC of its restoration procedures for a catastrophic situation. The Contractor shall provide the CFP or Government POC with updates NLT every four-hours on the status of restoration actions.

2.1.4.1.1. The following defines a high priority outage:

• Loss or degradation to any single or multiple Session Initiation Protocol (SIP) trunk(s), to include supporting systems infrastructure (Core Unified Communication Servers/ Database/ SAN), supporting wireline/fiber infrastructure, and delivery systems (i.e. Multiprotocol Label Switching (MPLS) or equivalent) regardless of location, that result in the following conditions:

- Complete loss of SIP trunking capability to the Government facility regardless of the source location of the outage

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the Call Setup Success Rate (CSSR) falls below 25% of system capacity

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the Dropped Call Rate (DCR) exceeds 50% of system capacity

- Loss of greater than 75% of total call handling capability of any legacy analog communications system

2.1.4.2. Medium Priority Outage. A medium priority outage may be a sudden or widespread disaster stemming from the result of a man-made or natural disaster, which disrupts service to property, equipment, and site infrastructure. The Contractor shall respond on-site to the outage NLT 24-hours after receiving notification by the Government

POC.

2.1.4.2.1. The following defines a medium priority outage:

• Loss or degradation to any single or multiple SIP trunk(s), to include supporting systems infrastructure (Core Unified Communication Servers/ Database/ SAN), supporting wireline/fiber infrastructure, and delivery systems (i.e. MPLS or equivalent) regardless of location, that result in the following conditions:

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the CSSR falls below 75% of system capacity

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the DCR is greater than 5% but less than 50% of system capacity

- Loss of greater than 25% but less than 75% of total call handling capability of any legacy analog communications system

2.1.4.3. Low Priority Outage. A low priority outage minimally disrupts service to property, equipment, and site infrastructure. The Contractor shall respond on-site NLT five working days of notification by the Government POC. All future references to days shall indicate working days unless otherwise noted.

2.1.4.3.1. The following defines a Low Priority Outage:

• Loss or degradation to any single or multiple SIP Trunk(s), to include supporting systems infrastructure (Core Unified Communication Servers/ Database/ SAN), supporting wireline/fiber infrastructure, and delivery systems (i.e. MPLS or equivalent) regardless of location, that result in the following conditions:

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the CSSR) falls below 90% of system capacity

- Partial loss of SIP trunking capability to the Government facility regardless of the source location of the outage when the DCR exceeds greater than 1% but less than 10% of system capacity

- Loss of greater than 1% but less than 25% of total call handling capability of any legacy analog communications system

2.2. Services Summary

2.2.1. Services Summary (SS)

Performance Element Number

Performance Objective

PWS

Paragraph

Performance Threshold

1 Perform and provide local access at the designated circuit demarcation points identified in Appendix 1 to this PWS.

2 Continuous operation local and long distance phone service 24/7/365 with 99.99% availability

2 Inform the Government POC NLT 30 days in advance of scheduled outage providing a detailed explanation for the outage.

2.1.1 Timely and detailed

notification provided 95% of time

3 Responds and restores High Priority service outages IAW PWS, TSP, and RPL as coordinated with the Government POC.

2.1.4 and 2.1.4.1

Timely response to notification and timely restoration of services provided 99% of the time

4 Respond and restore Medium Priority service outages IAW PWS, TSP, and RPL as coordinated with the Government POC.

2.1.4 and 2.1.4.2

Timely response to notification and timely restoration of services provided 95% of the time

5 Respond and restore Low Priority service outages IAW PWS, TSP, and RPL as coordinated with the Government POC.

2.1.4 and 2.1.4.3

Timely response to notification and timely restoration of services provided 95% of the time

2.2.2. Inspection. The performance threshold briefly describes the minimum acceptable levels of service required for each requirement. The Government has the right to inspect all services identified within the contract (SS and Non-SS items), to the extent practicable at all times and places during the term of the contract.

2.2.3. Grade of Service. Locations carrying contracted voice grade, which is packetized for transport across an IP, MPLS, or other IXC system require grade of service (GoS), implemented as quality of service (QoS), to ensure that end-to-end per-call latency and packet jitter remain within ITU standards. This requirement is applicable to VoIP traffic, video traffic, or other real-time traffic that has been identified and contracted for an elevated GoS. Vendor will ensure QoS end to end including through sub-contracted external LEC/CLEC facilities; implementation strategies that may include Committed Access Rates (CAR), Expedited Forwarding (EF), and traffic shaping determined by customer marked DSCP packets or pre-contracted data flows.

3. GOVERNMENT PROVIDED SPACE AND SERVICES

3.1. Securing and Safeguarding

The Contractor shall be responsible for safeguarding all Government property provided for its use. The Contractor shall secure Government facilities, property, and materials before leaving a facility. The Contractor shall safeguard the Government furnished facilities and material contained therein.

3.2. Rack Space

The Government will provide rack space for the installation of the Contractor’s provided transmission equipment. The floor space shall be coordinated with the Government POC to accommodate Contractor-provided relay rack(s), at each demarcation point. Space is available for relay rack(s) for Contractor equipment in the demarcation point.

3.3. Environmental Controls

The Government will provide sufficient environmental controls to maintain humidity and temperature within the Contractor’s equipment operating specifications. In addition, the Government will provide primary and emergency conditioned power sources to operate the Contractor’s equipment within manufacturer’s specifications.

3.4. Wall Space

The Government will also provide adequate wall space.

4. GENERAL REQUIREMENTS

4.1. Personnel

The Contractor is solely responsible for ensuring sufficient personnel are assigned to this requirement. Appropriate personnel shall possess the qualifications and certifications to perform the requirements listed herein. These qualifications and certifications shall include those required by the Original Equipment Manufacturer (OEM) to maintain, install, and/or operate the equipment covered by this contract.

4.2. Government Emergency Telecommunications Service (GETS)

GETS will be used in an emergency or crisis situation when the Public Switched Telephone Network (PSTN) is congested and the probability of completing a call over normal telecommunication means has significantly decreased. The Contractor must have NPA (710) in the switch to allow access to the GETS line assigned to a specific site.

Authorized users are provided access to an emergency service by dialing 0/1+710-NXX- XXXX. The 710 NPA provides access to a tariffed service of the GETS interexchange carriers and the call is billed to the United States Government. The Contractor shall not provide 10-10 dial around for this CSA.

4.3. Installation and Cutover Plans

In the event that the award is made to the incumbent contractor, no installation/cutover plans are required and this PWS section shall not apply.

In the event the award is made to a non-incumbent contractor, the incoming Contractor shall develop an installation and cutover plan for submittal to the Government with their technical proposal. This plan shall include installation of the initial required services for cutover of local CSA requirements, along with the recommended time frame to complete the cutover process. The Contractor shall coordinate deviations from the proposed installation plan with the Government POC prior to any work commencing in the affected area. The Contractor shall ensure that all circuits, equipment, and service provided by the incumbent, under the prior contract, are disconnected/discontinued upon successful cutover. At this point, the Contractor shall inform the Government POC that the incumbent’s equipment is no longer needed and may be removed by the incumbent. Any omissions or discrepancies in the installation/cutover plans do not relieve the Contractor of its responsibility to install, cutover, and perform all services identified in this requirement. It is the Contractor’s responsibility to resolve any issues associated with these efforts within a time agreed upon by the Government POC and the contractor.

4.3.1. Installation Plan. The Installation Plan shall contain, at a minimum, the following site-specific information:

a. Description of new equipment to be installed (include any site support required to support this installation)

b. Detailed location of equipment to be installed

c. Floor Plan Layout

d. Installation schedule

4.3.2. Cutover Plan

The Cutover Plan shall, at a minimum, contain the following site-specific information:

a. Conditions/Support required being in place prior to the start of cutover

b. A detailed listing of actions/events that must occur for successful cutover of all items identified in the Appendix 1

c. A listing of the awarded Contractor responsibilities

d. A listing of Government responsibilities

e. A dialing test plan to ensure ported numbers work correctly

f. A dialing test to access the GETS

4.4. Safety, Health and Fire Protection Requirements

This PWS requires no special safety precautions outside of OSHA standard safety requirements.

5. ACCESS AND GENERAL PROTECTION POLICY AND PROCEDURES

This standard language is for contractor employees with an area of performance within Government controlled installation, facility, or area. The contractor shall comply with all applicable installation/facility access and local security policies and procedures, which may be obtained from the Contracting Officer’s Representative (COR). The contractor shall also provide all information required for background checks to meet installation access requirements to be accomplished by the local installation’s Security Forces, Director of Emergency Services or local Security Office. The contractor shall ensure compliance with all personal identity verification requirements as directed by DoD, HAF and/or local policy. Should the Force Protection Condition (FPCON) change, the Government may require changes in contractor security matters or processes.

5.1. Contractors Requiring Common Access Card (CAC). Before CAC issuance, the contractor employee requires, at a minimum, a favorably adjudicated National Agency Check with Inquiries (NACI/Tier 1) or higher investigation IAW DoDI 5200.46. The contractor employee will be issued a CAC only if duties involve one of the following: (1) Both physical access to a DoD facility and access, via logon, to DoD networks on-site or remotely; (2) Remote access, via logon, to a DoD network using DoD-approved remote access procedures; or (3) Physical access to multiple DoD facilities or multiple non-DoD federally controlled facilities on behalf of the DoD on a recurring basis for a period of 6 months or more. At the discretion of the sponsoring activity, an initial/interim CAC may be issued based on a successfully scheduled NACI with the Office of Personnel Management and a favorable completion of an FBI fingerprint check.

5.2 Contractors that do not require CAC. Contractor and all associated sub-contractors employees shall comply with adjudication standards and procedures using the National Crime Information Center Interstate Identification Index (NCIC-III) and Terrorist Screening Database (TSDB) (AFI 10-245, AFI 31-101 and AFMAN 31-113), applicable installation, facility and area commander installation/facility access and local security policies and procedures (provided by government representative), or, at OCONUS locations, in accordance with status of forces agreements and other theater regulations.

6. APPENDICES

APPENDIX 1 – SITE SPECIFIC REQUIREMENTS

6.1. Required Services and Features

The Contractor shall provide the following Government line of local and long-distance commercial communications services for Battle Creek ANGB, MI at cutover. Innovative technical solutions are encouraged but must be compatible with the current requirement that is listed in the remainder of this Appendix. The quantity of these initial service requirements will be incorporated into the Pricing Schedule. The installation service requirement will be identified here and in the Pricing Schedule.

This is a firm-fixed-price contract. Historical usage of long-distance and toll-free minutes are provided in Appendix 2 for reference only. For any services provided on a per minute basis, the Government is liable only for the monthly minutes stated in the contract schedule. If contract minutes are exceeded, the contractor shall terminate service until additional minutes are added to the contract. If the contractor fails to control or terminate usage, the Government is only liable for monthly minutes within the contract schedule.

Contract price is inclusive of all applicable taxes and fees.

The Government telephone switching system is identified as an Avaya S-8800 with CM

7.0.1.2 software version. The switching system is located in Bldg (B) 6904, 3559 Mustang Ave, Battle Creek MI.

The Government Communication Services Officer (CSO) and Technical Representative shall be identified at the post award conference and updates provided to the contractor as required by the CO.

6.2. Direct-Inward-Dialing (DID) Directory Numbers.

NPA- NXX-XXXX DID Directory Numbers

(269) 969-3200 to 3599 400

(269) 660-5900 to 5999 100

(269) 660-6800 to 6899 100

TOTAL 600

6.3. Exchange and Access Lines.

6.3.1. Commercial Subscriber Lines. The number of Commercial Subscriber Lines (CSL) is: 3.

(NPA)-NXX-XXX Type

Services and Optional Features

Demarcation

Organization & End Demarcation

Location

(269) 963-4548 Dedicated Line

Analog BS (Basic Service), FR (Flat Rate)

B 6904 3559 Mustang Ave.

Battle Creek, MI 49037

B 6911, SFS

34 Sabre Ave.

Battle Creek, MI 49037

(269) 963-2165 Dedicated Line

Analog BS, FR

B 6904 3559 Mustang Ave.

Battle Creek, MI 49037

B 6905, CP

3545 Mustang Ave.

Battle Creek, MI 49037

(269) 963-1583 Dedicated Line

Analog BS, FR B 6904 3559 Mustang Ave.

Battle Creek, MI 49037

B 6914, Operations 50 Sabre Ave.

Battle Creek, MI 49037

6.3.2. Toll-Free Lines.

(800) 432-4296 Toll-Free Line Recruiting

BS, FR, Busy Line Transfer, Alternate Answering, Voice Mail

6.4. Local Exchange and Access Trunks. N/A

6.4.1. Local Exchange Access Analog Trunks. N/A

6.4.2. Local Exchange Access Digital Trunks. N/A

6.4.3. Local Exchange Digital (ISDN Primary Rate Interface (PRI) Trunks.

ISDN PRI

Circuit ID

D- Channe l

IC

B-Channel Quantity & Signaling:

(PRI Q.931)

OG

B-Channel Quantity & Signaling:

(PRI Q.931)

2 Way Channel B-Channel Quantity & Signaling

(PRI Q.931):

Qty

Demarcation

PRI #1 1 23 B 6904

3559 Mustang Ave Battle Creek, MI 49037

PRI #2 1 23 B 6904

3559 Mustang Ave Battle Creek, MI 49037

6.5. Foreign Exchange (FX) Lines/Trunks. N/A

6.5.1. Analog FX Line/Trunks. N/A

6.5.2. Foreign Exchange Digital Trunks. N/A

6.6. Transport Channels. N/A

6.7. Data Point-to-Point Circuits. N/A

6.8. Circuit Extension. N/A

6.9. Public Listings.

Description Qty Public Listing, Government Section 0 Cross Reference Listing, Alphabetical Section 0 Additional Listings 3 Foreign Listing, Government Section 0

6.10. Telephone Directories. N/A

6.11. Diversity/Diverse Routing. N/A

6.12. E911 Compatibility

The Contractor shall provide access to 911 services, where available, through the local city or county emergency services organization All 911 calls generated on-base through the base switch are routed to the local Calhoun County dispatch. The dispatcher determines the type of emergency assistance required and alerts the appropriate agency.

All 911 calls generated from commercial subscriber lines are routed from the LEC switch back to Calhoun County dispatch.

6.13. Special Services

Examples of vendor circuit/trunk routing supporting Appendix 1 requirements are provided in the below diagrams 1 and 2. These examples apply to ANG and Government sites with switches and/or PBX configuration, for Traditional Legacy or SIP trunking delivery. The Carrier, if providing a CPE installed digital loop carrier system or other IP based CPE gateway system, will provide the customer with IP, VLAN, routing protocols or other pertinent information to allow the customer to logically interface with the carrier system. The customer owned demarcation device will in most cases consist of an Edge Boundary Controller providing isolation and firewall services. The vendor shall provide a 24/7 capability to monitor the IP connection to the customer gateway equipment and alert the customer to a link failure; the customer must also have the ability to reach the vendor’s network operations center on a 24/7 basis.

6.14. Service Routing.

Contractor shall submit a service routing diagram (reference Appendix Diagrams 1 and 2 for examples) and/or service routing description in their technical quote. Contractor may provide the requested diagram and legend using these formats or a similar format to be in compliance with paragraph 4.3.1. Submission of a generic diagram or not explaining the service routing may be determined technically unacceptable.

Pump House

Off Govt Quarters

Apple

Medical Facility

Vendor / Incumbent Local Exchange Carrier (ILEC) / Competitive Local Exchange

Carrier (CLEC) Dial Central Office (DCO)

Police Dept

Remote Switch/PBX

Foreign City DCO 583 Claire Blvd

# of BRI and CSL

Off Premise

Voice Grade

Hotline

4 - Wired Data

2 - Wired Alarm

# of PRIs and DIDs

Main Site DCO 1234 AF Road, Any Base, USA

GOVT

SWITCH

GOVT

MDF

# of BRI and CSL

# of PRIs and DIDs

Foreign Exchange

Trunk

Outside Local LATA

Diagram 1

TRADITIONAL LEGACY

VENDOR/LEC/ILEC

NETWORK

PRI

LEC Provided BRI

CPE (SIP)

GIG

Ether

Govt Provided

Unified

Communications

IP Network

Note: The vendor-controlled Customer Premise Equipment (CPE) shall be vendor provided. The EBC, if available, shall be Government provided.

Legacy Services & Equipment

Diagram 2

UTILIZING SIP TRUNKING

Multifunction Edge Router

Edge Boundary Controller (if available)

APPENDIX 2 – LONG DISTANCE AND TOLL-FREE USAGE

LONG DISTANCE USAGE

Month/Year

LD

Minutes

Used

LD

Minutes

Used

LD

Minutes

Used January 2023 6557 September 2023 6255 May 2024 7435 February 2023 7192 October 2023 6255 June 2024 5366 March 2023 6967 November 2023 5366 July 2024 7130 April 2023 6451 December 2023 3898 August 2024 6402 May 2023 7952 January 2024 7382 September 2024 4670 June 2023 7600 February 2024 6438 October 2024 5713 July 2023 6097 March 2024 5833 Average Usage 6398 August 2023 7423 April 2024 6368 Peak Usage 7952

1-800-432-4296 (State Recruiting toll free) over 5 years.

Total calls received: 20

Total Minutes: ~ 60

APPENDIX 3 - DEFINITIONS & ACRONYMS

Table A. Definitions

TERM DEFINITION

Appendix 1 Defines the Battle Creek ANGB, MI requirements detailing locations on circuit delivery.

Call Setup Success Rate (CSSR)

The fractionalized amount of calls that make a successful connection to a dialed number, this is divided by the total number of calls placed. (As defined by International Telecommunication Union).

Circuit Termination Circuit termination at the Government installation includes the Main Distribution Frame (MDF) for analog signals, metallic cable pairs, Digital Signal Cross-Connect (DSX)-1 patch, cross connect panel(s) for T-1 and/or T-3 circuits, fiber optic patch and cross connect panels for optical interface equipment such as the optical carrier or SONET or MPLS systems, optical multiplexer equipment, and may extend to Cat 3/5/6 RJ-45 jack fields if directed by the Government POC to ensure adequate hand off of the circuit to the Government. Other wall-mounted, punch-down, terminal blocks are used for isolation and termination of Contractor metallic facilities.

Communications Focal Point (CFP)

A 24/7 Focal Point located on an Air Force Facility that provides one stop notification services and provides reporting and tracking of communications outages to Government users of the communication systems.

Commercial Subscriber lines

(CSL)

A CSL is defined by Government standards as a voice grade subscriber line serving directly from the Contractor’s central office switch to customer’s location.

Competitive Local Exchange Carrier

(CLEC)

A telephone company that competes with the already established local telephone business by providing its own network and switching.

Contractor A supplier or vendor awarded a contract to provide specific supplies or service to the Government. The term used in this contract refers to the prime.

TERM DEFINITION

Customer Premise Equipment (CPE)

Also known as Customer-Provided Equipment is any equipment located at a subscriber's premises and connected with a carrier's telecommunication network at the contractually established demarcation point. The demarcation point contractually separates the customer equipment from the equipment located in either the distribution infrastructure or central office of the communications service provider. Vendor installed CPE devices are fully vendor owned, maintained, and monitored by the Vendor’s management platform. CPE equipment can be powered from the customer source electrical system, but a sufficient emergency power source must be available during periods of customer power interruption for any services contractually requiring a high level of reliability.

Customer Service Record (CSR)

Report that details the fixed monthly charges billed by the local telephone company. The CSR is composed of computer codes called USOCs, which in turn correspond to a particular tariffed service.

Defective Service A service output that does not meet the standard of performance associated with the PWS.

Deliverable Anything that can be physically delivered, but may include non-manufactured things such as meeting minutes or reports.

Dropped Call Rate

(DCR)

The fractionalized amount of calls that experience a lost connection after a successful initial call establishment. (As defined by International Telecommunication Union).

DS-1 A DS level and framing specification for synchronous digital streams, over circuits in the North American digital transmission hierarchy, at the DS1 transmission rate of 1,544,000 bits per second. DS1 is commonly used to multiplex 24 DS0 channels.

Each DS0 channel, originally a digitized voice-grade telephone signal, carries 8000 bytes per second (64,000 bits per second). A DS1 frame includes one byte from each of the 24 DS0 channels and adds one framing bit, making a total of 193 bits per frame at 8000 frames per second. The result is 193*8000 = 1,544,000 bits per second.

Edge Boundary Controller (EBC)

A customer provided network node device that provides firewall, intrusion detection, routing, QoS, and packet equalization between the Vendors IP Wide Area Network and the interior customer IP network. The EBC will provide the logical demarcation point between IP SIP delivered services when applicable and will physically interface to the vendor’s CPE Gateway Router device.

Extended Area Calling Service

A geographic area beyond the local service area to which traffic is classified as local for selected customers, i.e., telephone service that allows subscribers in one exchange to call subscribers of another exchange without a toll charge or for a negotiated fixed rate.

Flat Rate A non-fluctuating monthly rate for telephone service in which an unlimited number of local calls can be made without further charge the extent of the contract. The monthly rate is established in the contract.

Government Emergency Telecommunications Service (GETS)

A White House-directed emergency phone service provided by the National Communications System (NCS) in the Cyber Security & Communications Division, National Protection and Programs of the Department of Homeland Security. GETS supports Federal, State, local, and tribal Government, industry, and non-Governmental organization (NGO) personnel in performing their National Security and Emergency Preparedness (NS/EP) missions. GETS provides emergency access and priority processing in the local and long distance segments of the Public Switched Telephone Network (PSTN). It is used in an emergency or crisis situation when the PSTN is congested and the probability of completing a call over normal or other alternate tele-communication means has significantly decreased. The servicing LEC must have NPA (710) in the switch to allow access to the GETS line assigned to a specific site. Dialing 0/1+710-NXX-XXXX provides access to an emergency service for authorized users. The 710 NPA provides access to a tariffed service of the GETS interexchange carriers (AT&T, MCI WorldCom, and Sprint) and the call is billed to the U.S.

Government. Web link:

http://gets.ncs.gov/

Incumbent Local Exchange Carrier

(ILEC)

The dominant phone carrier within a geographic area as determined by the FCC Section 252 of the Telecommunications Act of 1996 provided local exchange service to specific area.

Interconnection Agreement

A business contract between telecommunication organizations for interconnecting their networks and exchanging telecommunication traffic. These agreements are present in both public switched telephone networks and the Internet.

Intra LATA Local toll service (also called intra-Local Access and Transport Area (LATA), local long distance, or regional toll service) provides calling within a geographic area known as a LATA. Per-minute toll charges usually apply to these calls.

Local Exchange Access and Service Areas

Areas shall include the areas/zones coverage as currently defined by the incumbent local service provider(s) and/or the State PUC for the Site and shall be applied under the scope of this contract and provide a list of these local exchange access service areas and any updates as they accrue. When the Contractor provides services to a Government installation, the LATA boundary shall not be limited or restricted to a Contractor’s service area. Connection to intra-LATA exchange areas and with inter-LATA exchange carriers is required.

Measured Rate A message rate structure in which the monthly phone line rental includes a fixed rate on calls within a defined area. Measured services are often charged on the number of calls, the time of day, the distance traveled and/or the length of the call.

Non-Recurring Charges

A one-time fee IAW the established tariff rates at time of award that is associated with adding a local exchange service, including installment, activation and/or equipment.

Physical Security Actions that prevent the loss or damage of Government property.

Quality Assurance The Government procedures to verify that services being performed by the Contractor are performed according to acceptable standards.

Quality Control All necessary measures taken by the Contractor to assure that the quality of an end product or service shall meet contract requirements.

Reliability The probability that a system will not fail during a specified period of time.

Resilience The ability of a system to recover to its normal operating form after a failure or an outage.

Session Initiation Protocol (SIP)

A communications protocol for signaling, call setup/teardown, and communication of telephone and Video Real-Time Systems over an IP Based Unified Communication System. (As defined by Internet Assigned Numbers Authority & Request for Comments).

Session Initiation Protocol (SIP) Trunking

A Voice over Internet Protocol (VoIP) and streaming media service Based on the SIP by which Internet telephone service providers (ITSPs).

SIP Trunk An IP Based virtual connector between Unified Communication Systems designed to transport high-density unicast & multicast telephone/video traffic channels.

Traffic Analysis Inference of information from observable characteristics of data flow(s), such as the identities and locations of the source(s) and destinations(s), and the presence, amount, frequency and duration of occurrence.

TABLE B ACRONYMS:

ACRONYM EXTENDED

AF Air Force AFI Air Force Instruction BRI Basic Rate Interface BS Basic Services BTN Billing Telephone Number CSSR Call Setup Success Rate CFP Communications Focal Point CLEC Competitive Local Exchange Carrier CO Contracting Officer CPE Customer Premise Equipment CSL Commercial Subscriber Lines CSO Communications Services Officer DCO Dial Central Office DCR Dropped Call Rate DFARS Defense Federal Acquisition Regulation Supplement DID Direct In Dial DOD Department of Defense DP Dial Pulse DSN Defense Switching Network DSX Digital Signal Cross-Connect DTMF Dual Tone Multi-Frequency EBC Edge Boundary Controller FCC Federal Communications Commission FD Full Duplex FR Flat Rate FX Foreign Exchange GETS Government Emergency Telecommunications Service GS Ground Start HD Half Duplex IAW In Accordance With IC Incoming

ACRONYM EXTENDED

ILEC Incumbent Local Exchange Carrier ISDN Integrated Services Digital Network IT Information Technology LATA Local Access Transport Area LS Loop Start LTS Local Telecommunications Services MF Multi-Frequency MDF Main Distribution Frame MR Measured Rate NCS National Communications System NS/EP National Security and Emergency Preparedness NGO Non-Governmental Organization NLT No Later Than OEM Original Equipment Manufacturer OG Outgoing POC Point of Contact PRI Primary Rate Interface PUC Public Utility Commission PWS Performance Based Work Statement PSTN Public Switched Telephone Network RPL Restoration Priority List SIP Session Initiation Protocol SS Services Summary TS Telecommunication Services TSP Telecommunications Services Priority WS Wink Start