POT PGC02416_ JROTC.pdf

JACKET, WINDBREAKER, UNISEX SHALL BE IN ACCORDANCE WITH PD JD-01

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER

LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES

A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS. This solicitation/award consists of the following documents, exhibits, and other attachments:

DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, NOVEMBER 3, 1997.

US ARMY JROTC

ADDITIONAL INFORMATION FOR PD JD-01:

., Sample Size: Medium

PATTERN DATE: JUNE 12, 2013

ROLL NO. 3814 IS AVAILABLE FOR SHADE ONLY.

INTERIM CHANGES TO JACKET, WINDBREAKER, UNISEX

PAGE 1, UNDER DESCRIPTION

ADD THE FOLLOWING "THE ENDS OF THE SLASH

POCKETS SHALL BE SECURELY BARTACKED, SUPERIMPOS-

ED OVER THE EDGESTITCHING ALONG THE WIDTH OF

THE POCKET WELT.

PAGE 1, DESCRIPTION, LINE 4, AFTER "SHOULDER

LOOPS (EPAULETS)"ADD "CENTERED ON THE SHOULDER

SEAM, BUTTON FOR SHOULDER LOOP SHALL BE PLACED

1-1/4 INCH FROM THE COLLAR JOINING SEAM"

AT THE END OF THE PARAGRAPH ADD

"NOTE: THE SHOULDER SEAM ON PATTERN SHALL BE

CENTERED ALONG THE SHOULDER LINE."

PAGE 1 UNDER "ZIPPER" ADD "SLIDE FASTENER"

SHALL BE SET 1/4 TO 1/2 INCH ABOVE FRONT

LOWER FOLDED EDGE OF JACKET AND SHALL

FINISH SMOOTH AND FLAT"

PAGE 1 UNDER "STITCHING" ADD "SEAM ALLOWANCE

SHALL BE 1/2 INCH FOR ALL SEAMS EXCEPT COLLAR

AND COLLAR STAND WHICH SHALL BE 3/8 INCH."

PAGE 1, UNDER LINING MATERIAL, DELETE AND

SUBSTITUTE: "THE REMOVABLE LINER SHALL BE

A QUILTED 2-OZ PER SQUARE YD POLY FILL, WITH

DIAMOND OR RAILROAD STITCH."

DELETE CURRENT "BAR-CODE LABEL/TAG"

REQUIREMENTS AND SUBSTITUTE THE FOLLOWING

"LABEL/TAG. EACH ITEM SHALL BE INDIVIDUALLY

BAR-CODED WITH A PAPER TAG FOR PERSONAL

CLOTHING ITEMS. THE PAPER USED FOR THE TAGS

SHALL BE STANDARD BLEACHED SULFATE HAVING A

BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH

FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT

PRINTING. THE TAGS SHALL HAVE A HOLE AND

SHALL BE ATTACHED TO EACH ITEM BY A FASTENER

CLEARLY LEGIBLE AND READABLE BY SCANNER

THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

DELETE CHART OF DIMENSIONS AND SUBSTITUTE:

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE

A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT

THE INITIALS "UPC" MUST APPEAR BENEATH THE

CODE. THE BAR CODES FOR NSN AND UPC SHALL BE

A MEDIUM TO HIGH DENSITY AND SHALL BE

LOCATED SO THAT THEY ARE COMPLETELY VISIBLE

ON THE ITEM WHEN IT IS FOLDED AND OR PACKAGED

AND SHALL CAUSE NO DAMAGE TO THE ITEM."

DELETE CHART OF DIMENSIONS AND SUBSTITUTE:

SIZE XXSMALL XSMALL SMALL TOL

A. CHEST 20-1/2 22-12 24-1/2 +/- 1/2"

B. BOTTOM 14 15-1/4 16-1/2 +/- 1/2"

. SWEEP

C. SLEEVE 33-1/2 34-1/2 35-1/2 +/- 1/2"

. LENGTH

D. CENTER 26-1/2 27 27-1/2 +/- 1/2"

. BACK

E. SHOULDER 17-1/4 18-1/2 19-3/4 +/- 1/2"

SIZE MEDIUM LARGE X-LARGE TOL

A. CHEST 26-1/2 28-1/2 30-1/2 +/- 1/2

B. BOTTOM 17-3/4 19 20-1/4 +/- 1/2"

. SWEEP

C. SLEEVE 36-1/2 37-1/2 38-1/2 +/- 1/2"

. LENGTH

D. CENTER 28 28-1/2 29 +/- 1/2"

. BACK

E. SHOULDER 21 22-1/4 23-1/2 +/- 1/2"

SIZE XX-LARGE TOL

A. CHEST 32-1/2 +/- 1/2"

B. BOTTOM 21-1/2 +/- 1/2"

. SWEEP

C. SLEEVE 39-1/2 +/- 1/2"

. LENGTH

D. CENTER 29-1/2 +/- 1/2"

. BACK

E.SHOULDER 24-3/4 +/- 1/2"

(A) CHEST: TWICE THE MEASUREMENT TAKEN ACROSS

THE FRONT AT BASE OF THE ARMHOLE SEAM FROM

FOLDED EDGE TO FOLDED EDGE.

(B) BOTTOM SWEEP: TWICE THE MEASUREMENT TAKEN

FROM THE FOLDED END TO FOLDED END TAKEN AT CENTER

OF KNITTED WAISTBAND IN A RELAXED POSITION.

C) SLEEVE LENGTH: MEASUREMENT TAKEN STARTING AT

CENTER BACK AT UNDERCOLLAR JOINING SEAM, OVER

TOP SHOULDER SEAM TO BOTTOM OF SLEEVE.

(D) CENTER BACK: MEASUREMENT TAKEN FROM THE

CENTER OF THE BACK UNDERCOLLAR SEAM TO BOTTOM

OF THE JACKET.

(E) ACROSS SHOULDER: MEASUREMENT TAKEN ACROSS

BACK FROM SHOULDER POINT TO SHOULDER POINT.

BASIC MATERIAL PHYSICAL REQUIREMENTS TESTING

CHARACTERISTIC REQUIREMENT TEST METHOD

FIBER CONTENT,

.PERCENT POLYESTER 65 +/-3 AATCC 20-A

. COTTON 35 +/- AATCC 20-A

YARN PLY

.WARP 2 PLY OR VISUAL

.FILLING SINGLES VISUAL

WEIGHT,

.OZ/SQ YD 5.3-6.8 ASTM D 3776

YARNS PER

.INCH (MIN)

. WARP 180 ASTM D 3775

. FILLING 70 ASTM D 3775

WEAVE PLAIN VISUAL

AIR PERMEABILITY,

.(MAX) 10.0 ASTM D 737.75

BREAKING STRENGTH,

.LBS, (MIN.) 180 ASTM D 5035

.FILLING 70 ASTM D 5035

TEARING STRENGTH,

.LBS (MIN).

.WARP 5.0 ASTM D 1424

.FILLING 2.0 ASTM D 1424

DIMENSIONAL

.STABILITY,

.PERCENT(MAX.)

.WARP 3.0 AATCC 96, Vc,D .FILLING 3.0 AATCC 96, Vc,d

LABILE SULPHUR EQUAL TO STANDARD 2020 1/

. OR "SLIGHT"

COLORFASTNESS TO:

.LAUNDERING

.( AFTER 3 CYCLES) 3.0 AATCC 61,3A

.PERSPIRATION 3.0 AATCC 15

.CROCKING (MIN) 2.5 AATCC 8

.WET DRYCLEANING 3.0 AATCC 132

.LIGHT

.(AFTER 40 STD.

. FADING HOURS) 3.0 AATCC 16, OPT. A

.PH 5.0-8.5 AATCC 81

1/ FED-STD-191 TEST METHOD CITED

PACKAGING/PACKING REQUIREMENTS:

COMMERCIAL PACKAGING AND PACKAGING SHALL BE

ACCEPTABLE PROVIDED IT IS SUFFICIENT TO

PREVENT DAMAGE TO THE ITEMS DURING SHIPPING.

THE CONTRACTOR WILL BE RESPONSIBLE FOR ANY

IN-TRANSIT DAMAGE OR LOSS.

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON

WHICH THE NSN APPEARS).

(Ref. W2416)

AQLS FOR COMMERCIAL ITEM DESCRIPTION (CIDS)

END ITEM DIMENSIONAL 2.5

VISUAL 4.0

PALLETIZATION 6.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

USE OF "SAMPLING PROCEDURES AND TABLE FOR

INSPECTION BY ATTRIBUTES". ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL II

COMMERCIAL PACKAGING AUTHORIZED FOR

NON DEPOT SHIPPING

ACCORDING TO ASTM D 3951

THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT

CODE (UPC) MUST BE PLACED ON ALL SHIPPING

CARTONS ON WHICH THE NSN APPEARS".

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp.

Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT

EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING

THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS.

THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET

LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE

NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE

NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END

OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED

QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) -

(JULY 2006)