PID Packaging and Marking 4320-01-412-8596.docx

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:014128596

PUMP UNIT, RECIPROCATING.

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:A1202

REFERENCE NUMBER:RQ032

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RT001

REFERENCE NUMBER:CA070

REFERENCE NUMBER:CS220

DWG NRS 93107914, 93107915, 8611321, 23, 26, 27<(>,<)>

31, 32, & 35 CALL OUT FINISH RQMTS THAT SHALL BE

EXCEPTIONED AS FOLLOWS:

"PRETREAT EXTERIOR METAL SURFACES PER MIL-C-5541

CLASS 1A, PRIMER PER MIL-P-23377 TYPE I CLASS C

OR MIL-P-85582 TYPE I CLASS C2, AND PAINT PER

MIL-C-85285 TYPE II. EXTERIOR COLOR OF ALL

COMPONENTS VISIBLE AFTER INSTALLATION, INCLUDING

CLOTH, VELCRO, ETC, SHALL APPROXIMATE DESERT

SAND, COLOR #33446 PER FED-STD-595."

NOTE: THIS DESERT SAND COLOR #33446 DOES NOT

SHOW AS AN APPROVED COLOR ON QPL 85285-6. THE

QPL, HOWEVER, IS ONLY TO BE USED TO CONTACT

THESE PAINT MFGRS TO SEE IF THEY CAN SUPPLY A

COLOR THAT APPROXIMATES DESERT SAND #33446.

IF THE MFGRS CAN FURNISH AN APPROXIMATE COLOR<(>,<)>

THEY ARE ACCEPTABLE TO FURNISH THEIR PAINT IN

SPITE OF THIS COLOR NOT SHOWING ON THE QPL.

EXCEPTION NR 2; FOR THE ID & INST PLATE DWG NR

8611334, LEAVE THE "SUPPLY CATALOG NO" BLANK.

CXCEPTION NR 3; FOR FIND N0 175 ON PARTS LIST

DWG NR 8611325, THE CORRECT P/N SHOULD BE READ

MS35207-260. FOR FIND NO 224 ON THIS SAME PARTS

LIST, THE CORRECT P/N SHOULD READ WPG-2 AND THE

MANUFACTURER FOR THIS P/N IS PASS AND SEYMOUR."

REFERENCE NUMBER:ZD080

REFERENCE NUMBER:CS187

REFERENCE NUMBER:CPC01

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 98752 8611320

REVISION NR F DTD 07/22/2005

PART PIECE NUMBER: 8611320-150

IAW REFERENCE DRAWING NR 98752 8611323

REVISION NR C DTD 07/02/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611324

REVISION NR D DTD 07/20/1993

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611325

REVISION NR C DTD 07/17/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611325

REVISION NR C DTD 07/03/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611331

REVISION NR B DTD 01/08/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611331

REVISION NR B DTD 01/08/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611334

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611335

REVISION NR A DTD 11/27/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611348

REVISION NR B DTD 07/03/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8719896

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611346

REVISION NR DTD 06/12/1989

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611348

REVISION NR E DTD 02/02/2001

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611321

REVISION NR E DTD 07/08/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611321

REVISION NR B DTD 07/03/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611322

REVISION NR C DTD 07/11/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611322

REVISION NR B DTD 07/12/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611326

REVISION NR D DTD 07/11/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611328

REVISION NR B DTD 02/17/2010

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611328

REVISION NR C DTD 07/11/1999

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611332

REVISION NR D DTD 04/26/2000

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611332

REVISION NR B DTD 03/21/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107916

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107916

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107921

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611327

REVISION NR C DTD 06/02/1997

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611330

REVISION NR A DTD 12/01/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611333

REVISION NR A DTD 11/27/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611343

REVISION NR A DTD 11/01/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611343

REVISION NR A DTD 01/08/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611344

REVISION NR B DTD 01/11/1996

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107914

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107915

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107915

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107917

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107918

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107919

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107922

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611346

REVISION NR B DTD 11/29/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611320

REVISION NR H DTD 10/15/2008

PART PIECE NUMBER: FIND NO. 150

IAW REFERENCE DRAWING NR 98752 8611357

REVISION NR C DTD 12/29/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 200415485

REVISION NR E DTD 01/30/2020

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 8611329

REVISION NR B DTD 02/16/2010

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107912

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107912

REVISION NR DTD 12/15/1993

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 98752 93107923

REVISION NR DTD 12/07/1995

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951.

Mark and label all packaging and packing in accordance with MIL-STD-129.

The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order.

PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING

REQUIREMENTS FOR PROCUREMENT

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER A1202

Casting/forging may be required to manufacture this NSN. If a casting/forging is required, tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil

REFERENCE NUMBER RQ032

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at:

https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT

REFERENCE NUMBER CA070

FULL AND OPEN COMPETITION APPLY

REFERENCE NUMBER CS220

SINCE THIS NSN IS A NAVY FIELD LEVEL REPARABLE

ITEM CONFIGURATION CONTROL MUST BE MAINTAINED

PER MIL-STD-973.

REFERENCE NUMBER ZD080

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

REFERENCE NUMBER CS187

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

REFERENCE NUMBER CPC01

"SPECIFICATION CONTROL"