PID_PACK.pdf

PID-PACK INFORMATION

BRAKE, MLG, AIRCRAFT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY

REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE

WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON

THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE

DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RD002, COVERED DEFENSE INFORMATION APPLIES

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS

(MANUFACTURERS AND NON-MANUFACTURERS)

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED

SUPPLIES

Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations

(ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at:

https://www.dla.mil/Logistics-Operations/Enhanced-Validation/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

RT001: MEASURING AND TEST EQUIPMENT

THIS IS A SOURCE CONTROLLED ITEM WHICH MUST BE

MANUFACTURED AND TESTED IN ACCORDANCE WITH THE

CITED LIMITED RIGHTS DATA. THE GOVERNMENT CAN-

NOT PROVIDE THE DATA. ONLY THOSE VENDORS WHO

HAVE ACCESS TO THE DATA OR CAN PROVIDE TRACE-

ABILITY TO THE APPROVED SOURCES SHOULD QUOTE.

SAR PACKAGE IS REQUIRED IF YOUR COMPANY IS

CONSIDERING SOURCE APPROVAL.

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS

OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL,

MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS

OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION

OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE

LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

DWG: 901-336-006 P/N: 901-336-006-117

CRITICAL APPLICATION ITEM

AIRCRAFT WHEEL AND BRAKE, LLC 33269 P/N 030-17821

THE BOEING COMPANY 77272 P/N 901-336-006-117

IAW BASIC DRAWING NR 77272 901-336-006

REVISION NR J DTD 06/16/2015

PART PIECE NUMBER: 901-336-006-117

IAW REFERENCE DRAWING NR 77272 901-336-006

REVISION NR M DTD 06/16/2015

PART PIECE NUMBER: