PGC 03363 Tech Data Sand.pdf

TECH DATA PGC03363 3/9/2021

UNDERSHIRT, MAN'S

NSN 8420015461470

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

TYPE I.

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

ADDITIONAL INFORMATION FOR A-A-50013:

THE UNDERSHIRTS SHALL BE MADE IN ACCORDANCE

WITH A-A-50013G DATED SEPTEMBER 15, 2009

TYPE 1 SAND 1643,CREW NECK

STANDARD SAMPLE FOR SAND 1643 IS AVAILABLE

FOR SHADE, APPEARANCE AND COLORFASTNESS

AND IDENTIFIED AS ROLL NO. 14-02

shade swatching requirement Please add the following shade swatching requirement:

"52.246-9031

SHADE SWATCHING EVALUATION REQUIREMENT

(A) SAMPLING: NOTWITHSTANDING ANY CURRENT PROVISIONS OF THE FABRIC SPECIFICATION, THE FOLLOWING SHADE EVALUATION SHALL APPLY TO THIS SOLICITATION. A 4X12 INCH SHADE SWATCH WILL BE CUT BY THE CONTRACTOR FROM THOSE PIECES OR ROLLS SELECTED BY THE GOVERNMENT

REPRESENTATIVE, IN ACCORDANCE WITH THE FOLLOWING TABLE:

LOT SIZE (PIECES) PIECES TO BE SAMPLED

1 TO 8 EACH PIECE

9 TO 25 8 PIECES

26 TO 90 20 PIECES

91 TO 160 32 PIECES

OVER 160 PIECES 1 OF EVERY 5 PIECES"

The color and appearance of the undershirt shall match the standard sample when viewed using AATCC Evaluation Procedure 9, Option A, with filtered tungsten lamps that approximate artificial daylight and having a correlated color temperature of 7500 +/- 200 K, with illumination of 100 +/- 20 foot candles, and shall be a good match to the standard sample under Incandescent A lamplight at 2856 +/- 200 K.#

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

c. DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018 additional changes:

Page 10 of 38, par. 2.1, line 4, after "(DCMA QAS)" add ", or Supplier's Source Sampling Representative, as applicable"

Page 11 of 38, par. 2.3, line 2, delete "to the source QAS". Line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative". Page 12, par 2.3 (continued), delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 12 of 38, par. 2.4, line 5, delete "as required" and replace with "if required".

Page 12 of 38, par. 3.1.1, after "entirely" add the following: "For routine shade or physical testing of fabric lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier's Source Sampling Representative in Box 15."

Page 13 of 38, par. 3.1.2 - line 10, after "Government QAS" add the following: "or Supplier's Source Sampling Representative, as applicable,"

Page 14 of 38, par. 3.2.1 -line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.1 - cutting swatches, delete "DCMA QAS" and replace with "Supplier's Source Sampling Representative". After "single color rolls - 4"x 24"" delete "QAS" and replace with "Supplier's Source Sampling Representative". After "multi-color camouflage"... delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.2 - line 3, delete "stamped,". Line 4, Delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.1.4 - subpar. 2, delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.2 - Line 3, delete "stamped,", delete "source QAS" and replace with "Supplier's Source Sampling Representative". Line 4, delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 16 of 38, par. 3.3.1 - Line 2, after "(30)" add, "calendar". Line 3 and Line 6, after "QAS" add, "or Supplier's Source Sampling Representative"

Page 16 of 38, par. 3.3.2 - Delete the paragraph in its entirety, including subparagraphs labeled "a" through "i", and replace with the following:

"3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants. The following provisions apply to sample selection and lot acceptance.

(a) The samples shall be randomly selected by the Supplier's Source Sampling Representative.

(b) Upon presentation of a lot, the Supplier's Source Sampling Representative will draw samples and forward the samples to the contractor's laboratory specified in the contract for testing.

(c) Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation).

Commencement of production prior to receipt of a passing test report from the contractor's authorized laboratory is solely at the contractor's risk.

(d) The contractor will provide copies of Certificates of Compliance to the QAS.

(e) The contractor is required to ensure that a complete test report for all lots is furnished to the source's QAS and the appropriate DLA-PTC representative."

Pages 24, 25, 36 add to block 16: "By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

**Special note: Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information. Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor's representative samples, these blocks shall include the contractor's representative's information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.

[End of interim changes.]

ADDITIONAL INFORMATION FOR PPP-B-636:

FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL

SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM- D-1974, STANDARD PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD

SHIPPING CONTAINERS.

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD

INSPECTION.

ADDITIONAL INFORMATION FOR MIL-STD-105E:

MIL-STD-105E, dated 10 May 1989, is hereby canceled.

Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes."

Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document.

(Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

(Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.)

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR

SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

PACKAGING. THREE UNDERSHIRTS OF THE SAME SIZE

SHALL BE PACKAGED WITH A CARDBOARD INSERT IN A

POLYETHYLENE BAG.

PACKING. 120 UNDERSHIRTS IN A SHIPPING CARTON.

THE SHIPPING CONTAINER SHALL BE A FIBERBOARD BOX

CONFORMING TO STYLE RSC-L, TYPE CF (VARIETY SW)

OR SF, CLASS DOMESTIC, GRADE 275 OF ASTM-D1974

THE INSIDE OF EACH BOX SHALL BE FITTED WITH A

BOX LINER CONFORMING TO TYPE CF, CLASS DOMESTIC,

VARIETY DW, GRADE 275 OF ASTM-D1974. INSIDE

DIMENSIONS OF THE BOX SHALL BE APPROXIMATELY

23-1/2 INCHES IN LENGTH, 15 INCHES IN WIDTH AND

15 INCHES IN DEPTH. EACH BOX SHALL BE CLOSED

IN ACCORDANCE WITH METHOD II AS SPECIFIED IN

ASTRM-D1974. ALL SHIPPING CARTONS SHALL HAVE A

NSN AND UPC BAR CODE LABEL. MARKING OF CARTONS

AND SHIPPING LABELS SHALL BE IN ACCORDANCE WITH

MIL-HDBK-129. PALLETIZATION SHALL BE IN

ACCORDANCE WITH MIL-HDBK-774.

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129

PACKAGING SECTION. ADD THE FOLLOWING:

NOTE: UNIVERSAL PRODUCT CODE INFORMATION

THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON AL SHIPPING CATONS ON

WHICH THE NSN APPEARS.

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item.

Where the use of self-adhesive bar-code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz.

The RFID antenna should be Avery/Dennis AD222 or comparable with ISO/IEC 18000-C EPCglobal C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number.

The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ASAP. The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not laying flat when packaged RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual "Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance on RFID implementation and is available from the contracting officer.

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFID) Required (ref. T8379; Nov. 08, 2006)

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING

MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

Methyl Bromide fumigation in accordance with the National Wood Pallet and Container Association (NWPCA) quality control program developed in coordination with the United States Department of Agriculture, Animal and Plant Health Inspection Service (see http://www.aphis.usda.gov/ppq/wpm/export/fumigation.html)

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS

SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES

IN HEIGHT (INCLUDING THE PALLET).

REFERENCE PAGE 16 OF MIL-HDBK-774, ANY 4-WAY ENTRY PALLET

ILLUSTRATED IS ACCEPTABLE.

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING

MATERIALS. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF

IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO

LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN

ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY

BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY

MARKED "SHORT" OR "OVER".

MIL-HBK-774 IS HEREBY REFERENCED FOR GUIDANCE FOR PALLETIZED LOADS.