Salient_Characteristics__DES_Fleet_Vehicle_Aftermarket_Equipment.pdf

PDF 250 KB Posted

Attached to
Conservation Law Enforcement Office (CLEO) - Fort Carson, Colorado, Vehicle Fleet Aftermarket Parts Upgrades
Solicitation number
PANMCC27P0000057984
Issued by

About this file

This document is a Salient Characteristics Specification for commercial aftermarket components and integration hardware for three Model Year 2024 heavy-duty 3/4-ton fleet pickup trucks procured by the Directorate of Emergency Services (DES). The specification establishes minimum mechanical, structural, dimensional, and operational standards for contractor-furnished aftermarket parts and Government-Furnished Equipment (GFE) integration without reference to proprietary manufacturer names or brand designations.

For all three vehicles, contractors must procure and install one HD winch-ready brush guard bumper per vehicle featuring minimum 3/16-inch structural carbon steel body construction, minimum 1/4-inch structural steel frame uprights, and fully welded heavy-wall tubular brush guard (1.5–2 inch outer diameter tubing) with integral reinforced winch tray accommodating 16,500-lb planetary-gear electric recovery winches. All bumpers require non-destructive mounting to OEM front chassis horns using Grade 8 fasteners with zero frame cutting, drilling, or welding, and must maintain adequate thermal clearances and sensor accommodations. Vehicles 1 and 2 require procurement of four heavy-duty commercial-grade all-terrain tires per vehicle (LT265/70R17, Load Range E, minimum 121 load index, 3PMSF and M+S rated) dynamically balanced to 0.25-ounce tolerance with TPMS compatibility. Vehicle 3 excludes tire procurement. Contractors must furnish Grade 8 structural fasteners, heavy-duty aluminum or stainless steel bed rail tie-down clamps with closed-cell neoprene/EPDM pads for toolbox installation, steel backing plates and anti-vibration fasteners for headache rack mounting, and electrical integration hardware including minimum 2/0 AWG power cables for 15,500-lb winches and minimum 6 AWG cables for 2,000-lb winches with high-amperage circuit breakers or mega-fuse holders positioned within 12 inches of the battery terminal. Installation requirements mandate torquing bumpers to OEM specifications, testing winches under battery power with conduit-routed power lines secured away from steering linkages and exhaust manifolds, centering and leveling toolboxes with weather-resistant seals, and for Vehicles 1 and 2 only, providing documented disposal manifests for eight removed commercial tires from a licensed facility and torquing lug nuts to 135 ft-lbs OEM specification.

View the file

Other files

File Type Posted
Sources Sought Notice CLEO Trucks.pdf PDF

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

SALIENT CHARACTERISTICS

SPECIFICATION

Commercial Aftermarket Components and Integration Hardware Procuring Activity: Directorate of Emergency Services (DES) Requirement Type: Government Commercial Supply and Mechanical Installation Solicitation Applicable Vehicle Platform: Model Year 2024 Heavy-Duty 3/4-Ton Fleet Pickup Trucks (Total: 3 Vehicles)

1. SCOPE AND ACQUISITION FRAMEWORK

This document delineates the essential physical, functional, and performance salient characteristics required for the commercial aftermarket equipment to be procured and installed under a competitive government contract. In accordance with federal acquisition principles governing competitive solicitations, all requirements are specified by minimum mechanical, structural, dimensional, and operational standards without reference to proprietary manufacturer names or brand designations.

The procurement encompasses contractor-furnished aftermarket parts to be purchased as new commercial items, associated mounting/electrical integration hardware, and the mechanical integration of Government-Furnished Equipment

(GFE).

2. FLEET ALLOCATION SUMMARY

Fleet Identifier Platform Contractor- Procured Items

Government Furnished Equipment (GFE) Integration Scope

Vehicle 1 2024 Heavy-Duty 3/4-Ton Pickup Truck

• (1) HD Winch- Ready Brush Guard Bumper

• (4) Heavy-Duty All-Terrain Tires

• Commercial Mounting & Electrical Kits

• 15,500-lb Front Recovery Winch

• Aluminum Crossover Bed Toolbox

• Steel Headache Rack & 2,000-lb Bed Winch

Vehicle 2 2024 Heavy-Duty 3/4-Ton Pickup Truck

• (1) HD Winch- Ready Brush Guard Bumper

• (4) Heavy-Duty All-Terrain Tires

• Commercial Mounting & Electrical Kits

• 15,500-lb Front Recovery Winch

• Aluminum Crossover Bed Toolbox

• Steel Headache Rack & 2,000-lb Bed Winch

Vehicle 3 2024 Heavy-Duty 3/4-Ton Pickup Truck

• (1) HD Winch- Ready Brush Guard Bumper

• Commercial Mounting & Electrical Kits (Tire procurement excluded)

• 15,500-lb Front Recovery Winch

• Aluminum Crossover Bed Toolbox

• Steel Headache Rack & 2,000-lb Bed Winch

3. VEHICLE 1: SALIENT CHARACTERISTICS

3.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard

• Quantity Required: One (1) Unit.

• Component Classification: Full-width structural steel replacement bumper assembly with integrated full-front grille and headlight tubular brush protection.

• Physical Characteristics:

• Material & Thickness: Minimum 3/16-inch (approx. 4.76 mm) structural carbon plate steel body construction, with structural frame mounting uprights fabricated from minimum 1/4-inch (approx. 6.35 mm) structural steel plate.

• Upper Protective Structure: Fully welded, one-piece wrap-around tubular brush guard constructed of heavy-wall structural steel tubing (minimum 1.5-inch to 2-inch outer diameter) providing complete protective coverage for the vehicle radiator grille, cooling package, and primary headlight assemblies.

• Winch Mounting Configuration: Integral, reinforced structural winch tray/channel located between frame mounting rails, engineered to accommodate standard commercial planetary-gear heavy-duty electric recovery winches rated up to 16,500 lbs. Must feature standard foot-down or foot-forward bolt mounting patterns and a forward-facing cutout compatible with standard 10-inch hawse or roller fairleads.

• Recovery & Shackle Points: Dual heavy-duty recovery tabs/clevis mounts (minimum 1-inch thick solid steel) welded continuously directly through the face plate into the primary structural frame brackets, accommodating standard 3/4-inch or 7/8-inch screw-pin recovery shackles.

• Finish & Corrosion Protection: Multi-stage industrial finish comprising an anti-corrosive electro-coat (e-coat) primer underlayer sealed with a heavy-duty, UV-stable, textured black powder-coat finish rated for a minimum 1,000 hours of continuous salt-spray corrosion resistance.

• Functional & Performance Characteristics:

• Chassis Compatibility: Direct structural bolt-on compatibility engineered specifically for a Model Year 2024 heavy-duty 3/4-ton pickup truck chassis.

• Non-Destructive Mounting: Must mount entirely to existing OEM front chassis horns/frame attachment locations utilizing high-tensile Grade 8 (or metric Class 10.9) zinc-coated structural fasteners. Must require zero frame cutting, zero torching, zero chassis drilling, and zero frame welding.

• Thermal & Operational Clearances: Must preserve required operational airflow to the OEM engine radiator, transmission oil cooler, and intercooler matrices. Must maintain adequate body clearance (minimum 1/2-inch gap) to prevent body panel contact, hood-rub, or front fender deflection under extreme off-road chassis articulation.

• Lighting/Sensor Accommodations: Cutouts and mounting provisions for auxiliary forward-facing emergency or driving lighting, as well as provisions to retain factory parking sensor functionality where present.

3.2. Heavy-Duty Commercial-Grade All-Terrain Tires

• Quantity Required: Four (4) Tires.

• Dimensional Specifications:

• Nominal Tire Size: LT265/70R17 (Light Truck metric sizing).

• Rim Diameter Compatibility: 17.0 inches.

• Section Width: Approximately 10.7 inches (272 mm) on standard 17x8-inch fleet wheels.

• Overall Outer Diameter: 31.6 inches to 31.9 inches.

• Load & Construction Standards:

• Service Description & Ply Rating: Load Range E (10-Ply Rating equivalent).

• Load Index: Minimum 121 (minimum carrying capacity of 3,195 lbs per tire at maximum rated cold inflation pressure of 80 PSI).

• Speed Rating: Minimum Q rating (minimum 99 mph / 160 km/h continuous duty).

• Casing Construction: Reinforced radial construction with minimum 2-ply or

3-ply high-strength polyester or polyamide sidewall cord wrap designed to resist curb scrubbing, rock gouging, and puncture in austere off-pavement conditions.

• Tread Design & Performance Characteristics:

• Tread Classification: Aggressive hybrid commercial all-terrain / multi-surface tread with deep self-cleaning shoulder voids and continuous interlocking center tread blocks.

• Weather & Traction Certifications: Must bear the official Three-Peak Mountain Snowflake (3PMSF) severe snow service emblem and Mud & Snow (M+S) sidewall designations.

• Traction Features: Full-depth multi-angle tread siping for wet pavement and ice traction; integrated step-down stone ejector ribs within circumferential grooves to eliminate trapped gravel retention.

• Balancing & Fitment Standards:

• Dynamic, computerized wheel balance to within 0.25 ounces of true balance.

• 100% operational compatibility with vehicle OEM Tire Pressure Monitoring System (TPMS) valve stem sensors and OEM wheel hub clearances.

3.3. Contractor-Furnished Mounting & Electrical Integration Hardware

• Chassis & Structural Fasteners: High-strength Grade 8 steel bolts, through-hardened washers, and prevailing-torque locknuts for front bumper installation.

• Toolbox Mounting Hardware: High-tensile, heavy-duty aluminum or stainless steel bed rail tie-down clamps (J-hooks) and weather-resistant closed-cell neoprene/EPDM protective pads (no-drill bed installation).

• Headache Rack Mounting Hardware: Heavy-gauge structural steel backing plates, Grade 8 bolts, and anti-vibration locking fasteners for bed rail mounting.

• Electrical Integration Hardware (Front & Bed Winches):

• Heavy-duty multi-strand fine-copper automotive power cables (minimum

2/0 AWG for 15,500-lb winch; minimum 6 AWG for 2,000-lb winch).

• In-line high-amperage commercial circuit breakers or sealed mega-fuse holders placed within 12 inches of the vehicle primary battery terminal.

• Full split-loom abrasion-resistant flame-retardant automotive conduit and dual-wall heat-shrink sealed ring terminals.

4. VEHICLE 2: SALIENT CHARACTERISTICS

4.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard

• Quantity Required: One (1) Unit.

• Component Classification: Full-width structural steel replacement bumper assembly with integrated full-front grille and headlight tubular brush protection.

• Physical Characteristics:

• Material & Thickness: Minimum 3/16-inch structural carbon plate steel body construction, with structural frame mounting uprights fabricated from minimum 1/4-inch structural steel plate.

• Upper Protective Structure: One-piece fully welded tubular grille and headlight guard fabricated from minimum 1.5-inch to 2-inch outer diameter structural steel tubing.

• Winch Mounting Configuration: Heavy-duty internal steel winch cradle capable of supporting recovery winches up to 16,500 lbs capacity, featuring pre-drilled standard winch mounting hole patterns and integrated fairlead mounting face.

• Recovery Provisions: Dual integrated 1-inch solid steel clevis/D-ring attachment brackets welded directly through the face plate into primary chassis brackets.

• Finish & Corrosion Protection: Dual-coat finish consisting of an anti-corrosion chemical wash/e-coat primer and a commercial-grade textured black UV-resistant powder coat rated for a minimum 1,000 hours of salt-spray testing.

• Functional & Performance Characteristics:

• Chassis Fitment: Direct bolt-on design for a Model Year 2024 heavy-duty

3/4-ton pickup truck chassis.

• Installation Parameters: Mounts directly to OEM chassis mounting points via Grade 8 high-tensile hardware without requiring cutting, drilling, or chassis modifications.

• Clearances & Ventilation: Engineered cooling air vents that meet or exceed OEM cooling intake airflow requirements; adequate clearance from front body panels under dynamic suspension load.

• Sensor Provisions: Retention openings for forward parking sensors and provisions for factory fog or auxiliary lighting.

4.2. Heavy-Duty Commercial-Grade All-Terrain Tires

• Quantity Required: Four (4) Tires.

• Dimensional Specifications:

• Nominal Tire Size: LT265/70R17.

• Wheel Rim Diameter: 17.0 inches.

• Section Width: Approximately 10.7 inches (272 mm).

• Overall Outer Diameter: 31.6 to 31.9 inches.

• Load & Construction Standards:

• Service Description: Load Range E (10-Ply Rating equivalent).

• Load Index: Minimum 121 (3,195 lbs maximum load per tire at 80 PSI cold).

• Speed Rating: Minimum Q rating (minimum 99 mph).

• Sidewall Construction: Minimum 2-ply to 3-ply heavy-duty polyester/polyamide sidewall cord casing with proprietary cut-and-chip resistant compound.

• Tread Design & Performance Characteristics:

• Tread Pattern: Deep-groove commercial all-terrain pattern with high-void shoulder lugs, self-cleaning evacuation channels, and stone ejectors.

• Certifications: Severe Snow Service rated (Three-Peak Mountain Snowflake

/ 3PMSF) and Mud & Snow (M+S) rated.

• Compound: High-traction silica-infused rubber compound optimized for low-temperature elasticity and extended tread life under severe heavy-duty fleet operations.

• Balancing & Fitment Standards:

• Computerized dynamic balancing (maximum tolerance: 0.25 oz).

• Zero TPMS warning activations; full integration with OEM 17-inch heavy-duty wheel rims.

4.3. Contractor-Furnished Mounting & Electrical Integration Hardware

• Chassis & Structural Fasteners: High-strength Grade 8 steel bolts, through-hardened washers, and prevailing-torque locknuts for front bumper installation.

• Toolbox Mounting Hardware: Heavy-duty aluminum or stainless steel bed rail tie-down clamps (J-hooks) and weather-resistant closed-cell neoprene/EPDM protective pads (no-drill bed installation).

• Headache Rack Mounting Hardware: Heavy-gauge structural steel backing plates, Grade 8 bolts, and anti-vibration locking fasteners for bed rail mounting.

• Electrical Integration Hardware (Front & Bed Winches):

• Heavy-duty multi-strand fine-copper automotive power cables (minimum

2/0 AWG for 15,500-lb winch; minimum 6 AWG for 2,000-lb winch).

• In-line high-amperage commercial circuit breakers or sealed mega-fuse holders placed within 12 inches of the vehicle primary battery terminal.

5. VEHICLE 3: SALIENT CHARACTERISTICS

5.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard

• Quantity Required: One (1) Unit.

• Component Classification: Full-width structural steel replacement bumper assembly with integrated full-front grille and headlight tubular brush protection.

• Physical Characteristics:

• Material & Thickness: Minimum 3/16-inch structural carbon plate steel body construction, with structural frame mounting uprights fabricated from minimum 1/4-inch structural steel plate.

• Upper Protective Structure: One-piece fully welded tubular grille and headlight guard fabricated from minimum 1.5-inch to 2-inch outer diameter structural steel tubing.

• Winch Mounting Configuration: Heavy-duty internal steel winch cradle capable of supporting recovery winches up to 16,500 lbs capacity, featuring pre-drilled standard winch mounting hole patterns and integrated fairlead mounting face.

• Recovery Provisions: Dual integrated 1-inch solid steel clevis/D-ring attachment brackets welded directly through the face plate into primary chassis brackets.

• Finish & Corrosion Protection: Dual-coat finish consisting of an anti-corrosion chemical wash/e-coat primer and a commercial-grade textured black UV-resistant powder coat rated for a minimum 1,000 hours of salt-spray testing.

• Functional & Performance Characteristics:

• Chassis Fitment: Direct bolt-on design for a Model Year 2024 heavy-duty

3/4-ton pickup truck chassis.

• Installation Parameters: Mounts directly to OEM chassis mounting points via Grade 8 high-tensile hardware without requiring cutting, drilling, or chassis modifications.

• Clearances & Ventilation: Engineered cooling air vents that meet or exceed OEM cooling intake airflow requirements; adequate clearance from front body panels under dynamic suspension load.

• Sensor Provisions: Retention openings for forward parking sensors and provisions for factory fog or auxiliary lighting.

5.2. Tires and Wheel Assembly

• Procurement Status: Excluded from Procurement.

• Baseline Fleet Condition: Vehicle 3 retains existing serviceable fleet tire and wheel equipment. No tire purchase, removal, mounting, or disposal services are required for this specific vehicle unit.

5.3. Contractor-Furnished Mounting & Electrical Integration Hardware

• Chassis & Structural Fasteners: High-strength Grade 8 steel bolts, through-hardened washers, and prevailing-torque locknuts for front bumper installation.

• Toolbox Mounting Hardware: Heavy-duty aluminum or stainless steel bed rail tie-down clamps (J-hooks) and weather-resistant closed-cell neoprene/EPDM protective pads (no-drill bed installation).

• Headache Rack Mounting Hardware: Heavy-gauge structural steel backing plates, Grade 8 bolts, and anti-vibration locking fasteners for bed rail mounting.

• Electrical Integration Hardware (Front & Bed Winches):

• Heavy-duty multi-strand fine-copper automotive power cables (minimum

2/0 AWG for 15,500-lb winch; minimum 6 AWG for 2,000-lb winch).

• In-line high-amperage commercial circuit breakers or sealed mega-fuse holders placed within 12 inches of the vehicle primary battery terminal.

6. CONTRACTOR MECHANICAL INSTALLATION &

INTEGRATION REQUIREMENTS

In addition to physical product delivery, all items must be installed in full compliance with the following physical and mechanical standards:

1. Front Bumper & 15,500-lb Front Winch Integration:

• Bumpers shall be torqued to OEM structural chassis bolt specifications using high-tensile Grade 8 hardware.

• Winches shall be aligned, bolted, and mechanically tested under battery power. Power lines must be routed through protective conduit along the inner frame rails, securely fastened away from moving steering linkages and high-temperature exhaust manifolds, and fused directly at the battery terminal.

2. Crossover Bed Toolbox Installation:

• Toolboxes shall be centered, level, and fastened using non-destructive heavy-duty bed rail clamps.

• Weather-resistant closed-cell rubber stripping must be fitted along bed rails to guarantee a watertight seal without rattling or shifting under vehicle motion.

• Toolboxes must allow 100% unobstructed lid opening without contact against vehicle cabs or headache rack tubing.

3. Bed Headache Rack & 2,000-lb Utility Winch Integration:

• Headache racks shall be structurally fastened through bed rails with heavy-duty backing plates.

• Integrated utility bed winches and spare tire carrier brackets must be fully wired, insulated, and verified operational.

4. Tire Mounting, Balancing, and Disposal (Vehicles 1 and 2 Only):

• Tires must be dynamically balanced with zero highway speed vibration.

• Lug nuts shall be torqued to exact OEM specifications (135 ft-lbs or applicable OEM maintenance manual specification).

• Contractor must provide documented disposal manifests demonstrating

100% compliant environmental recycling of eight (8) removed commercial tires at a licensed facility.

SALIENT CHARACTERISTICS SPECIFICATION
Commercial Aftermarket Components and Integration Hardware
1. SCOPE AND ACQUISITION FRAMEWORK
2. FLEET ALLOCATION SUMMARY
3. VEHICLE 1: SALIENT CHARACTERISTICS
3.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard
3.2. Heavy-Duty Commercial-Grade All-Terrain Tires
3.3. Contractor-Furnished Mounting & Electrical Integration Hardware
4. VEHICLE 2: SALIENT CHARACTERISTICS
4.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard
4.2. Heavy-Duty Commercial-Grade All-Terrain Tires
4.3. Contractor-Furnished Mounting & Electrical Integration Hardware
5. VEHICLE 3: SALIENT CHARACTERISTICS
5.1. Front Heavy-Duty Winch-Ready Replacement Bumper with Brush Guard
5.2. Tires and Wheel Assembly
5.3. Contractor-Furnished Mounting & Electrical Integration Hardware

6. CONTRACTOR MECHANICAL INSTALLATION & INTEGRATION REQUIREMENTS

File details come from the government source that posted it. Updated .