Paint IDIQ - Pressure Washing Supplemental Final 26.pdf
PDF 106 KB Posted
- Attached to
- Painting IDIQ Maxwell AFB and Gunter Annex 2026
- Solicitation number
- A060321
About this file
PAINT IDIQ PRESSURE WASHING SPECIFICATIONS
This document contains pressure washing specifications for services to be performed at Maxwell Air Force Base (AFB) under an Indefinite Delivery Indefinite Quantity (IDIQ) contract awarded under the Paint IDIQ vehicle. The contractor must provide all management, personnel, equipment, tools, materials, vehicles, fuel, supervision, and services necessary to perform pressure wash cleaning as directed through Task Orders. Pressure washing shall be conducted using water only as the primary cleaning method. Cleaning solutions may be used only on areas where water alone is insufficient, and only with prior approval and direct supervision from the Civil Engineering Environmental Department. Approved cleaning solutions are limited to Topsall #30, Enviro-Klean, or Simple Green Oxy Solve Total Outdoor Cleaner, all of which must be eco-friendly and EPA-listed. All cleaning solutions and rinse water must be captured and prevented from entering groundwater or storm water systems through implementation of best management practices including drain covers, berms, barriers, plugs, and dikes. Equipment must be calibrated to deliver appropriate pound-force per square inch (PSI) without damaging surfaces.
The scope of work includes exterior cleaning of door frames, windowpanes, frames, awnings, fixtures, and exterior walls or facades to achieve uniform appearance free of dirt, mildew, bugs, grime, pollutants, debris, and detergent residue. Contractors must protect surrounding areas including vehicles, sidewalks, and landscaping from overspray through cordoning and tarping to maintain professional appearance. Prior to any structure cleaning, the contractor must conduct a pre-work assessment inspection within five days of the scheduled work date, identifying surfaces at risk for damage and presenting a cleaning strategy with cost estimates for each surface to the Government for approval.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Paint IDIQ - Statement of Work Final 26.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
PAINT IDIQ
PRESSURE WASHING SPECIFICATIONS
SECTION 1.0 – DESCRIPTION
The contractor shall provide all management, personnel, equipment, tools, material, vehicles and fuel, supervision, and services necessary to perform pressure wash cleaning at Maxwell Air Force Base (AFB) as needed per Task Order (TO). All pressure washing is to be conducted with water only. Cleaning solutions may be used only on areas where water only is not working and only with the approval and under the direct supervision of the Civil Engineering Environmental Department. The contractor shall submit specifications for the equipment and applicable Safety Data Sheets for cleaning solutions that they plan to use. All cleaning solutions used must be eco-friendly and be on the EPA’s Safe Products List. Maxwell Air Force Base allows the following cleaning solutions: Topsall #30, Enviro-Klean, or Simple Green Oxy Solve Total Outdoor Cleaner. If cleaning solutions are used, all solutions, including rinse water, must be captured and not allowed to enter ground or storm water systems. BMPs must be enforced to ensure that none of the runoff off enters the storm water system. Storm water drain covers, berms, barriers, plugs, and/or dikes must be placed over the drain openings to catch all runoff. Cleaner shall be applied using a bucket with the solution and stiff bristled brush and only on identified and approved difficult areas. No work using any cleaners shall begin without the Environmental Department’s approval and cleaners can only be used under the environmental department’s direct supervision, per MDEQ requirement.
Pound-force per square inch (PSI) calibrated equipment used shall be calibrated in such a way as to not damage surfaces being cleaned. Pressure washing shall be accomplished in accordance with all federal, state, local laws and regulations, and commercial standards as defined in this document.
1.1. Exterior Cleaning:
1.1.1. Door Frames: All doorframes, windowpanes and frames, awnings, and fixtures shall be cleaned in a manner that achieves a uniform and clean appearance without dirt, mildew, bugs, grime, pollutants, debris, or evidence of detergent residue after cleaning is accomplished.
1.1.2. Exterior Walls or Facades: All exterior walls shall be cleaned in a manner that achieves a uniform and clean appearance without dirt, mildew, bugs, grime, pollutants, debris, or evidence of detergent residue after cleaning is accomplished.
1.1.3. Over wash: Defined as the back splash of particulates, to include cleaning agents and surface residue, produced in the Pressure washing process. The contractor shall protect items around the effected cleaning area through various methods such as cordoning off the area and laying down tarps. The desire is to leave the area around the surface(s) cleaned undamaged with a neat, clean, and professional looking appearance. This would include vehicles, sidewalks, landscaping, etc.
PAINT IDIQ
1.2. Contractor Requirements:
1.2.1. Pre-work Assessment Inspection: Prior to any structure cleaning, the contractor shall conduct a pre-work assessment. The contractor shall identify surfaces that are at risk for damage if cleaned and shall present cleaning strategy for each surface and the cost of cleaning. The pre-work assessment shall be submitted to the Government within five (5) days of the work scheduled to be done.
~~End of Section~~
File details come from the government source that posted it. Updated .