OTTO Fuel - SOW.pdf

STATEMENT OF WORK

FOR

OTTO FUEL CONTAINERS, DWG 7263829 REV NR

1.0 INTRODUCTION

Naval Surface Warfare Center, Indian Head Division (NSWC IHD) has a requirement for the manufacture and delivery of 55-gallon Otto Fuel Containers, NSN 8140-01-054-6702, in accordance with drawing 7263829 Rev. NR and specification A-A-58020A, Type II, Class 4. The procurement is in support of the Otto Fuel II Production Program supported by NSWC IHD Energetics Manufacturing

Department.

1.1 Background

DWG 7263829 Rev NR, Otto Fuel Containers are used for the storage and shipment of Otto Fuel II, liquid.

1.2 Scope

This Statement of Work (SOW) describes and defines the work requested, documentation requirements, responsibilities, and deliverables for Otto Fuel Containers.

2.0 APPLICABLE DOCUMENTS

The Contractor is responsible for meeting the requirements of every applicable specification documented on the technical drawings, SOW, and contract. The following list of documents is intended as an overview for the top-level requirements for this SOW. The documents listed are of the issue in effect on the date of invitation for bids or request for proposals and form a part of this SOW to the extent herein.

2.1 Specifications

Document Number Document Title

A-A-58020 Drums, Shipping, Steel with Polyethylene Insert

ASTM D2000

Standard Classification System for Rubber Products in Automotive

Applications

49 CFR 100-199 Code of Federal Regulations; Title 49 Transportation

ASTM D3951 Standard Practice for Commercial Packaging

2.2 Drawings

Document Number Document Title

7263829 Rev NR OTTO FUEL CONTAINER

3.0 REQUIREMENTS

3.1 General

The Contractor shall manufacture, inspect/test, package, and deliver the required number of Otto Fuel

Containers in accordance with drawing 7263829 Rev NR and per the applicable documents listed in

Section 2.0.

3.2 Otto Fuel Container Manufacture

The drums shall be manufactured in accordance with drawing 7263829 Rev NR and specification A-A-

58020A, Type II, Class 4 for steel with polyethylene insert shipping drums.

3.3 Certification

The containers shall meet the performance oriented packaging (POP) requirements of 49 CFR 178.600 for

UN6HA1/Y1.2/100 and UN1A2/Y1.2/100 as specified in drawing 7263829 Rev NR, Notes 2D, 2E, and 3

(Critical). The manufacturer shall perform the required UN testing per 49 CFR Parts 173 and 178 and specification A-A-58020A Section 4.2. The manufacturer shall provide two (2) copies of the test report, CDRL A001, at the time of the first container delivery to NSWC IHD technical point of contact per specification A-A-58020A Section 5. The manufacturer shall provide one (1) copy of the certification of conformance to the UN test requirements.

As part of the quality control requirement, the Contractor shall provide Certification of Compliance for material and Certification of Conformance to drawings and specifications listed herein. The containers shall conform to the requirements of Drawing 7263829 Rev NR, ASTM-D-3951, and specification A-A-

58020A. The Contractor shall specify the contract number and container lot(s) or deliveries covered by the certificate of compliance for the material. Further the Contractor shall provide all relevant certifications for material to provide proof that the material is in accordance with drawing 7263829 Rev

NR. Certifications of Compliance/Conformance shall be provided by the Contractor, one (1) copy to accompany each shipment (in the packing list envelope) and one (l) copy mailed to arrive at time of receipt of each shipment. Mark all certificates to the attention of Code M24JT.

3.4 Inspection/Acceptance.

Final inspection and acceptance of the Otto Fuel Containers will be performed at NSWC IHD by the

Government. The objective of the inspection is to provide verification of conformance to applicable drawing requirements (dimensions and notes), specifications, and contract requirements. The

Government shall verify, through inspection, certification, audit, or test or any combination, the dimensional, material, and/or note conformance to drawing 7263829 Rev NR.

3.5 Packaging and Shipment

Contractor shall package the Otto Fuel Containers for shipment in accordance with specification ASTM

D3951. Otto Fuel Containers shall be palletized four per pallet, single stacked, and stretch wrapped on pallets. The pallets shall be 48” x 48” to ensure that the containers do not overhang the edge and to prevent damage to the containers during shipment. All shipments shall be on a dedicated tractor trailer, no matter how small the shipment. A label shall be placed on the shrink-wrap around each palletized assembly containing the following information: “Otto Fuel Container”, drawing number with revision, manufacturer name, contract number including call number and contract line item number (CLIN), quantity per pallet, and weight.

4.0 DELIVERABLES

Documentation deliverables as specified herein shall be delivered to the Technical Point of Contact, for review and approval/acceptance:

Technical Point of Contact:

Naval Surface Warfare Center, Indian Head Division

Attn: Julius Taylor, Code M24JT

3655 Nitramine Way

Building 765

Indian Head, MD 20640

Email: Julius.l.taylor7.civ@us.navy.mil

Phone: 301-744-6462

Otto Fuel Containers shall be delivered to the Receiving

Officer, for inspection and approval/acceptance:

Delivery Address:

Naval Surface Warfare Center, Indian Head Division

Receiving Officer, Bldg. 116

4522 McMahan Road, Suite 100

Indian Head, MD 20640-5125

4.1 Deliverables Schedule (Each subsequent order shall be an option)

This SOW consists of multiple options, as outlined in the table below.

Deliverables

Deliverable Quantity Due

Otto Fuel Containers 208 No later than 20 weeks following award of contract.

Certification of

Material

2 Two copies with Otto Fuel Container shipment

Certification of

Conformance*

2 Two copies with Otto Fuel Container shipment

UN Test Report, CDRL A001

2 Two copies prior to or at the time of the

Otto Fuel Container shipment

*Contractor to provide Certificates of Conformance to the requirements of Drawing 7263829 Rev NR, specification ASTM-D-3951, and specification A-A-58020A, and UN test requirement.