Attachment 1 - Statement of Work (SOW).pdf

CUI / SOURCE SELECTION SENSITIVE – SEE FAR 2.101 and 3.104

Statement of Work HF Cleaning Nozzles for T64 & F404]

17 July 2025

Prepared By: Jason Giroir, jason.p.giroir.civ@us.navy.mil

DISTRIBUTION STATEMENT D. DistribuƟon authorized to Department of Defense and U.S. DoD contractors only (Reference DoDI

5230.24 for reasons/categories) (Day Month Year). Other requests for this document must be referred to the AcquisiƟon and Program Management Competency

Controlled by: Department of the Navy Controlled by: COMFRC Procurement Group CUI Categories: PROCURE DistribuƟon/DisseminaƟon Controls: Click or tap here to enter text.

DoD Component or authorized CUI holder.

Teresa.j.harper8.civ@us.nav.mil

COMFRC Mission

1.0 INTRODUCTION: The Fleet Readiness Center East (FRC-E) is a tenant command located within MCAS Cherry Point, NC.

FRC-E is charged with the administration of unique repair procedures on various gas turbine engine components. Nickel, cobalt, and iron base super alloy turbine nozzles require a Hydrogen Fluoride (HF) Ion activated gas cleaning for removal of oxides and sulfides from their surfaces for subsequent braze repairs.

2.0 Scope & Requirement Background:

This Performance Work Statement (PWS) describes the requirements needed to HF ion clean T64 stage 3 turbine nozzles and F404 turbine nozzle segments. The approximate weight of a nozzle is five (5) pounds.

2.1 Modifications to this document of any kind require prior approval from FRC-E, MCAS Cherry Point, NC. Any such alterations will be authorized and performed at the convenience of the U.S. Government and will become the property of the U.S.

Government.

3.0 APPLICABLE DOCUMENT: The following standard is a part of this document as referenced to the extent specified herein. The latest edition of this standard must be used unless otherwise specified.

3.1 ASTM-D-3951, Standard Practice for Commercial Packing

4.0 REQUIREMENTS:

4.1 The contractor will perform HF Ion activated gas cleaning of the nozzles and return the nozzles to the Government. Return shipment of the part(s) shall not exceed 10 business days after receipt of part(s) or 10 additional business days for additional required cycles. The HF Ion activated gas cleaning process must conform to the following requirements:

a. A continuous denuded surface layer between 0.0005 and 0.001 inches deep at the base metal surface and intermittent denudation up to 0.003 inch deep. Denuded layer shall be free from yttrium, titanium, and aluminum.

b. There will be no continuous intergranular attack of the carbide phases; however, non- continuous intergranular attack up to

0.003-inch deep is acceptable below the denuded surface layer.

4.2 If evidence of oxide on the surface of the nozzles is identified following the cleaning process, the nozzles shall be grit blasted using 180-grit or finer aluminum oxide to remove visual surface oxidation and reprocessed for an additional cleaning cycle.

It is acceptable for components other than those processed per this document to be present in the furnace during HF cleaning cycles.

5.0 PARTS TO BE SERVICED:

5.1 Stage 3 Turbine Nozzle:

Nomenclature: Stage 3 Turbine Nozzle Description: Turbine Nozzle

NSN #: 2840-00-998-6812,

Part# 6011T24G02 Asset #: 009986812

Nomenclature: Stage3 Turbine Nozzle Description: Turbine Nozzle

NSN #: 2840-01-351-4850

Part #: 6011T24G04

To produce quality airframes, engines, components and support equipment and provide service that meet the Naval Aviation Enterprise's aircraft ready-for-tasking goals with improved effectiveness and efficiency.

Asset #: 013514850

Nomenclature: Stage 3 Turbine Nozzle Description: Turbine Nozzle

NSN #: 2840-01-456-2601

Part #: 6011T24G05 Asset #: 014562601

5.2 F404 High Pressure Turbine Nozzle Segments:

Description NSN # Part # Asset/NIIN #

F404 High Pressure Turbine Nozzle 2840-01-166-4886 6072T80G01 11664886

F404 High Pressure Turbine Nozzle 2840-01-166-4886 6072T80G03 11664886

F404 High Pressure Turbine Nozzle 2840-01-418-6032 6072T80G04 14186032

F404 High Pressure Turbine Nozzle 2840-01-494-8719 6072T80G05 14948719

5.3 F404 Low Pressure Turbine Nozzle Segments:

F404 Low Pressure Turbine Nozzle 2840-01-499-4998 6042T03G21 14994998

F404 Low Pressure Turbine Nozzle 2840-01-499-5003 6042T03G22 14995003

F404 Low Pressure Turbine Nozzle 2840-01-504-8915 6084T09G09 15048915

F404 Low Pressure Turbine Nozzle 2840-01-504-8914 6084T09G10 15048914

F404 Low Pressure Turbine Nozzle 2840-01-394-9254 6084T09G01 13949254

F404 Low Pressure Turbine Nozzle 2840-01-394-9255 6084T09G02 13949255

F404 Low Pressure Turbine Nozzle 2840-01-499-4998 6042T03G13 11302768

F404 Low Pressure Turbine Nozzle 2840-01-130-2769 6042T03G14 11302769

6.0 PACKAGING / SHIPPING

6.1 Preparation for Delivery – Each shipping unit or crate will be clearly, legibly, and permanently marked to show destination, purchase/task order number, gross weight, and number of units or crates in shipment. Marking, preservation, packaging, and packing shall be in accordance with ASTM-D-3951- 82 “Standard Practice for Commercial Packaging.” Additional markings are stated below:

“NOT FOR OUTSIDE STORAGE”

“MARK WITH PURCHASE/TASK ORDER NUMBER”

6.2 All equipment must be packed for shipment in a manner that will ensure acceptance by a common carrier and safe delivery to the consignee. Containers and closures must comply with Interstate Commerce Commission regulations, Uniform Freight Classification rules or regulations of other carriers as applicable to the mode of transportation (via ground – best method, FOB Destination).

6.3 Preservation, packaging, and packing must be in accordance with ASTM-D-3951-90, Standard Practice for Commercial Packaging.

6.4 Required Delivery Dates – pursuant to the requirements of each task order placed, stage 3 turbine nozzles will be shipped at the Government’s expense, FOB to the contractor. The contractor will process the nozzles as described in section 4.0 of this document and return the nozzles in the same shipping containers used to ship from the government to the contractor within ten (10) business days after receipt. If a second cleaning cycle was required as described in section 4.2, then the nozzles may be returned within twenty (20) business days.

6.5 Processed parts and documentation to be furnished hereunder will be delivered, FOB Destination to:

N65923 FRCE Receiving Officer Attn: PC Station 96 (464-9599) Beachey Rd., Bldg. 148 Bay Door A Cherry Point, North Carolina 28533-5040 Mark For: Tessa Elkins

7.0 The Customer Point of Contact for this contract shall be MRO LOGISTICS, Acquisitions Procurement Division:

Primary: Teresa Harper, teresa.j.harper8.civ@us.navy.mil (252)464-9821 Secondary: Angela Cannon, angela.m.cannon3.civ@us.navy.mil (252)464-7972

7.1 Technical POC: Kevin Smith, kevin.r.smith2.civ@us.navy.mil, (252)464-7555

7.2 Shipping POC: Tessa Elkins, tessa.r.elkins.civ@us.navy.mil, (252)464-9599

CUI / SOURCE SELECTION SENSITIVE – SEE FAR 2.101 and 3.104

WAWF Invoice Routing Instructions

Please fill out the following table with the proper DoDAAC’s to ensure proper rouƟng of invoices.

See WAWF Training and WAWF RouƟng Table Guidance. You can verify DoDAAC’s via DLA’s DoDAAD website.

If you’re not sure which code(s) to select, please reach out to your AcquisiƟon Specialist or the PCO for assistance.

Field Name in WAWF Data to be entered in WAWF Pay Official DoDAAC

Issue By DoDAAC N68520 Admin DoDAAC** N68520 Inspect By DoDAAC N65923 Ship To Code

Ship From Code

Mark For Code

Service Approver (DoDAAC) N65923 Service Acceptor (DoDAAC) N65923 Accept at Other DoDAAC

LPO DoDAAC N65923 DCAA Auditor DoDAAC

Other DoDAAC(s)

WAWF point of contact.

(1) The Contractor may obtain clarificaƟon regarding invoicing in WAWF from the following contracƟng acƟvity’s WAWF point of contact.

WAWF Acceptor: frce_acq_team.fct@navy.mil WAWF LPO NoƟficaƟon: CHPZ_ACCT_LPO@navy.mil