N6833524Q0883 Solicitation.pdf

N6833524Q0883

Section A - Solicitation/Contract Form

SUPPLEMENTARY INFORMATION

Procurement Point of Contact Alexander Buchan Email: alexander.g.buchan2.civ@us.navy.mil Phone: 848-240-2623

This requirement is solicited as a 100% Total Small Business Set-Aside. This solicitation is for the competitive procurement of the AFT Fuselage Support Fixtures, P/N: 4106AS0440-1, NSN: 1730-01-694-6230 in support of the MQ-4C Triton Unmanned Air Systems (UAS) Program for the United States Navy (USN) and Royal Australian Air Force (RAAF) aircraft.

It is anticipated that this solicitation will result in a single award, three (3) year Firm Fixed-Price, Indefinite Delivery/Indefinite Quantity (IDIQ) contract. The guaranteed minimum for the contract will be three (3) units which will be procured on the First Delivery Order. The maximum for the contract will be eight (8) units over the 3-year life of the contract.

Delivery Orders may be placed as follows:

Ordering Year 1 CLINs 1001 through 1002 from the date of award through 365 days after contract award.

Ordering Year 2 CLINs 2001 through 2002 from 366 days after contract award through 730 days after contract award.

Ordering Year 3 CLINs 3001 through 3002 from 731 days after contract award through 1,095 days after contract award.

Deliveries shall be made six (6) months after receipt of order. Delivery information can be found in FAR 52.211-8 of this solicitation.

This solicitation contains export-controlled technical data, subject to disclosure restrictions. Attention is directed to the following clauses contained in this solicitation:

DFARS 252.225-7048, Export-Controlled Items (Jun 2013) DFARS 252.204-7008, Compliance with Safeguarding Covered Defense Information Controls

IMPORTANT INFORMATION: Registration in the Department of Defense (DoD) System for Award Management (SAM) database will be a prerequisite for receiving an award. For more information on the SAM database, refer to the SAM website at https://www.sam.gov/portal/public/SAM.

RELEASE OF TECHNICAL DATA PACKAGE: This program includes information that is only releasable to current and approved Department of Defense (DoD) contractors. In addition, the program requires a procurement effort in certain critical technologies/data that are not releasable to foreign firms. Some documents are under Federal export control for “sensitive” or “controlled” technologies regulated by the U.S. Department of State International Traffic in Arms Regulations (ITAR) protecting national security. Data may not be exported without an approval, authorization, or license under E.O. 12470 or the Arms Export Control Act. Disclosure of the control drawings requires the verification of a current license for the oral, visual or documentary disclosure of technical data by U.S.

persons to foreign persons as defined under the U.S. Department website: http://pmdtc.org/licenses.htm. Please note the following applicable clauses: DFARS 252.225-7048, Export-Controlled Items (JUN 2013) and NAVAIR LTXT.227-9508, Qualified U.S. Contractors for Export-Controlled Technical Data (APR 1998).

Accordingly, the drawing package associated with this solicitation will NOT be posted with this solicitation.

Offerors interested in receiving the necessary technical data for quotation preparation purposes MUST submit a written request, including a copy of a valid, current DD Form 2345 (Military Critical Technical Data Agreement) to

Alexander Buchan at alexander.g.buchan2.civ@us.navy.mil no later than 22 August 2024, 4:00 PM EDT. Late requests may not be considered, and the solicitation period may not be extended to accommodate late requests.

DD Forms 2345 will be reviewed and, if found valid and complete, download instructions will be sent electronically to the designated data custodian through the DoD SAFE web application at https://safe.apps.mil/. Drawings will not be supplied to requestors who do not submit a Joint Certification Program verified DD Form 2345. For more information on Form DD2345, contact the Joint Certification Program by email at JCPADMIN@DLA.MIL or by phone at (877) 352-2255. The Joint Certification Program website and FAQs are available at https://www.dla.mil/Logistics-Operations/Services/JCP/.

RECEIPT OF CORRESPONDENCE: All correspondence pertaining to this solicitation shall be submitted to Alexander Buchan at alexander.g.buchan2.civ@us.navy.mil. All correspondence submitted shall be reviewed, and responses will be provided in Q&A format as an amendment to the solicitation, publicized on SAM.gov for all of industry to view.

Section B - Supplies or Services and Prices

IDIQ QUANTITY CONSTRAINTS

The maximum quantity identified herein for each CLIN represents the Government’s best estimate of the maximum quantities to be ordered during that specified ordering period. The CLIN quantity maximums do not impose absolute quantity limits for each ordering period. The maximum quantity for the equipment units are not defined on an annual ordering period basis, but rather is defined by the sum of the quantities identified across all three annual ordering periods.

The minimum and maximum quantities of this contract can be found in clause BTXT.216-9506 “Minimum and Maximum Quantities.” All quantities to be ordered under this contract shall be in accordance with each delivery order. The Government is not obligated to order any quantity beyond the guaranteed minimum and may order the maximum quantity over the life of the contract.

ITEM NO SUPPLIES/SERVICES MAX

QUANTITY

UNIT UNIT PRICE MAX AMOUNT

1001 5 Each AFT Fuselage Support Fixtures - Year 1

FFP

AFT Fuselage Support Fixtures, P/N: 4106AS0440-1, in accordance with the Statement of Work and applicable drawings.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

NSN: 1730016946230

MFR PART NR: 4106AS0440-1

PSC CD: 1730

MAX

NET AMT

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

1002 1 Lot Contract Data Requirements List Year 1

FFP

Contract Data Requirements List (CDRL) A001 - Request for Variance in accordance with Para 3.1 of the Statement of Work CDRL A002 Asbestos Containing Material in accordance with Para 3.2 of the Statement of Work CDRL A003 Proof Load Testing in accordance with Para 3.3 of the Statement of Work

This Line Item is Not Separately Priced FOB: Destination

UNIT UNIT PRICE MAX AMOUNT

2001 2 Each AFT Fuselage Support Fixtures - Year 2

FFP

AFT Fuselage Support Fixtures, P/N: 4106AS0440-1, in accordance with the Statement of Work and applicable drawings.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

NSN: 1730016946230

2002 1 Lot Contract Data Requirements List Year 2

FFP

Contract Data Requirements List (CDRL) A001 - Request for Variance in accordance with Para 3.1 of the Statement of Work CDRL A002 Asbestos Containing Material in accordance with Para 3.2 of the Statement of Work CDRL A003 Proof Load Testing in accordance with Para 3.3 of the Statement of Work

This Line Item is Not Separately Priced

UNIT UNIT PRICE MAX AMOUNT

3001 1 Each AFT Fuselage Support Fixtures - Year 3

FFP

AFT Fuselage Support Fixtures, P/N: 4106AS0440-1, in accordance with the Statement of Work and applicable drawings.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

NSN: 1730016946230

3002 1 Lot Contract Data Requirements List Year 3

FFP

Contract Data Requirements List (CDRL) A001 - Request for Variance in accordance with Para 3.1 of the Statement of Work CDRL A002 Asbestos Containing Material in accordance with Para 3.2 of the Statement of Work CDRL A003 Proof Load Testing in accordance with Para 3.3 of the Statement of Work

This Line Item is Not Separately Priced

CLAUSES INCORPORATED BY FULL TEXT

BTXT.216-9506 MINIMUM AND MAXIMUM QUANTITIES (NAVAIR)(MAR 1999)

As referred to in paragraph (b) of FAR 52.216-22 " Indefinite Quantity" of this contract, the contract minimum quantity is three (3); the maximum quantity is eight (8).

Section C - Descriptions and Specifications

STATEMENT OF WORK

STATEMENT OF WORK

AFT Fuselage Support Fixture

13 June 2024

1.0 SCOPE

This Statement of Work (SOW) is for the procurement of the AFT Fuselage Support Fixture, Part Number (P/N) 4106AS0440-1 for the MQ-4C Unmanned Air Systems (UAS).

The AFT Fuselage Support Fixture houses the Engine Exhaust Duct and provides the structural support for the left and right V-Tail Assemblies and the left and right vertical fins on the MQ-4C Triton Aircraft.

1.1 Applicable Documents:

a) MIL-STD-130N - Identification Marking of U.S. Military Property

b) Drawing #3909AS9999 Rev C- Identification Plate for Support Equipment/UID Markings

c) MIL-STD-2073-1E Standard Practice for Military Packaging

d) MIL-STD-129R - Military Marking for Shipment and Storage

e) MIL-STD-1366E - Transportability Criteria

f) Drawing Package Number – 4106AS0440 thru 4106AS0455, 4106AS0103 and 4106AS0105

2.0 REQUIREMENTS

2.1 General

Contractor shall manufacture and deliver AFT Fuselage Support Fixture in accordance with (IAW) this SOW, the Government furnished drawing package and the requirements of the contract.

The program is requesting a three (3) year Indefinite Delivery, Indefinite Quantity (IDIQ) type contract:

Part Number Description Base

USN

Qty.

Base

RAAF

Qty.

Yr. 1 Est Qty

Yr. 2 Est Qty.

Yr. 3 Est Qty.

4106AS0440-1 AFT Fuselage Support Fixture 2 1 2 2 1

Year 1 pricing valid from date of award through 365 days.

Year 2 pricing valid from 366 days through 730 days.

Year 3 pricing valid from 731 days through 1095 days.

2.2 Quality Assurance

The Contractor shall have in place a production quality assurance (QA) system. This QA system shall be able to ensure that manufactured configuration items are built to print, functional, and reliably made IAW controlling technical drawings, specifications, and standards. Each item manufactured as part of this contract shall have passed a Government final inspection prior to WAWF Receiving Report acceptance.

2.3 Certificate of Conformance -

The Contractor shall provide a Certificate of Conformance (COC) with each AFT Fuselage Support Fixture certifying that it conforms to the government drawing package, this SOW, and the requirements of the contract. The COC shall be on company letterhead and signed by management. Each COC shall identify the part number and serial number. If any item is found to be non-conforming, it shall be replaced at the Contractor’s expense.

2.4 Serial Numbers

The contractor shall assign a serial number for each Support Equipment end item. A unique, serial number as defined in the drawing is required for each item.

2.5 Government Inspection and Acceptance

Government Inspection and Acceptance shall be accomplished at destination by designated representatives.

2.6 Item Unique Identification (IUID) Marking of US Military Property In accordance with DFARS Clause 252.211-7003 Item Identification and valuation, the Contractor is required to mark and register all end items and their components meeting the requirements called out in MIL-STD-130N. These include components for which the Governments unit acquisition cost is $5,000 or greater, or any component, subassembly or embedded part that is serially managed, mission essential or a controlled inventory item.

2.6.1 Construct and Method

Details on creating the UID and the marking method are contained in MIL-STD-130N. The UID may be either UID Construct #1 or Construct #2 with Construct #2 being the preferred method.

2.6.2 UID Location and Marking

The locations and marking methods selected should bear no impact on the performance of the part and minimal configuration change(s) to the part. The UID (including 2D Matrix) should be incorporated onto the data plate in accordance with Drawing 3909AS9999 Rev C (Identification Plate/UID Markings).

2.6.3 Permanency and Legibility

The UID marking and identification plates, tags, or labels when used on equipment, parts, assemblies, subassemblies, units, sets, or groups shall be permanent during the normal life expectancy of the item and be capable of withstanding the environmental test and cleaning procedures specified for the item. Legibility shall be as required for ready readability as per MIL-STD-130N.

2.6.4 UID Registration

The prime Contractor has the responsibility to furnish Item Unique Identification (IUID) data to the IUID registry.

Data submission of IUID data and acquisition cost should be via Wide Area Work Flow (WAWF), IUID XML file, IUID flat file or web entry. Additional information regarding data submission as well as the actual marking can be found at <http://www.acq.osd.mil/dpap/pdi/uid/index.html/>.

2.6.5 Records

The Contractor shall maintain an accurate, current list of UIDs for all manufactured items on this contract and supply to the Government upon request. The list shall include P/N, Serial #, CAGE, UID Location, Construct used, how it was marked, and the registration method used.

3.0 CONTRACTS DATA REQUIREMENTS LIST (CDRL)

3.1 Request For Variance - (CDRL A001)

When identified, the contractor shall submit to the government for approval recommendations for a Request for Variance (RFV). Any proposed design changes affecting form, fit, and/or function of the PSE (including enhancements) that deviate from drawings provided shall be identified prior to the fabrication process and will be reviewed by the cognizant UAS Support Equipment Lead Engineer for approval/disapproval. The contractor shall submit to the Government for approval a Request for Variance (RFV) to request deviations from the contractually specified design configuration. The contractor is advised to consult MIL-HDBK-61 Configuration Management for guidance when contemplating submitting a RFV. These change requests shall be prepared and submitted to the Government IAW Contract Data Requirements List (CDRL) A001.

3.2 Asbestos Containing Material – (CDRL A002)

The Customs Legislation Amendment (COA) requires the Original Equipment Manufacturer (OEM)/ supplier/contractor provides the Government with word document or statement certifying the OEMs products material contains 0% asbestos (not less than 1% as per US regs). If an OEM/supplier/contractor states less than 1%, the OEM/supplier/contractor will be required to identify the items or areas of concerns. Request for Asbestos Containing Material Certification shall be submitted IAW the Statement of Work (SOW) and IAW Contract Data Requirements List (CDRL) A002.

3.3 Proof Load Testing – (CDRL A003)

Signed proof loading certificates that indicate Safe Working Load (SWL) and proof load shall be provided for every item ordered. The proof load tag shall indicate the SWL, proof load, and date the equipment was proof loaded.

"SWL" shall be stamped before the SWL weight on the tag. The proof load shall be submitted on company letterhead and shall have the serial number documented for each item. Copies of the proof load certificates shall be shipped with each item by placing them in a plastic pouch/envelope and attaching them to each unit or by using a temporary fastening device such as a zip tie. The original copies of all Proof Load Certificates shall be provided to the procuring activity in accordance with (IAW) Contract Data Requirements List (CDRL) A003. The Government shall be given the opportunity to witness the proof load testing.

4.0 PACKAGING, PRESERVATION AND SHIPPING

4.1 Packaging

Each AFT Fuselage Support Fixture PN 4106AS0440-1 shall be packaged separately IAW the below Standards and Requirements.

Preserve, and pack for shipment in accordance with the MIL-STD-2073-1E, Standard Practice for Military Packaging. The use of loose fill materials, asbestos, excelsior, newspaper, and shredded paper (all types) are prohibited. In addition, all Wood Packaging Materials (WPM) shall be heat treated or chemically treated in accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15:2009, "Regulation of Wood Packaging Material in International Trade.”

4.2 Marking

Marking shall be in accordance with MIL-STD-129R.

Additionally, special marking labels (fragile, delicate, etc.) shall be applied to all unit, intermediate and shipping containers as an integral part of the total pack. The contractor shall select the appropriate special marking label (s) as additional means to protect the items during packaging, handling, storage, transit, and removal from the pack.

4.3 Transportation

Transportability issues shall be identified and addressed to ensure all shipments can be transported with unrestricted movement via over-the-road transport. Transportability problem items shall be identified in accordance with MIL- STD-1366E criteria. Requirements for shipment of DOD materiel shall meet, as a minimum, the requirements of the following rules and regulations, as applicable to the mode of transportation in the Defense Transportation Regulation, DTR DOD 4500.9-R, Part II, Uniform Freight Classification Rules, National Motor Freight Classification Rules, and American Trucker’s Association Rules.

4.4 Shipping Addresses

USN Shipment:

NAWCAD Lakehurst SE Staging Facility NAWCAD Lakehurst, Rt. 547

HANGAR 1

Joint Base MDL, NJ 08733 Mark For: MQ-4C USN Program POC: Robert Hull, PH: 732-323-4611, Email: robert.m.hull30.civ@us.navy.mil *No Friday Deliveries

RAAF Shipment:

NAVSUP FLTLOGCEN Jacksonville Detachment, Gulfport, MS (RIC 4NN) 511 North Brown Ave, BLDG 437

Gulfport, MS 39501-5000 ATTN: RIC 4NN, DoDAAC N6694N POC: Penny Prestage, (985) 285-8228

All Follow-on Shipments:

DODAAC: SW310N

DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull PH: 732-323-4611 Email: robert.m.hull30.civ@us.navy.mil

* For items shipped to Mechanicsburg, PA:

*The contractor must instruct their carrier to request an appointment with DLA Mechanicsburg by filling out the attached “Prelodge Request Form” and emailing it to Prelodge@dla.mil.

Please note that an appointment is not needed for deliveries going to DLA that are being shipped via UPS, FEDEX, USPS etc. Therefore, the Prelodge form does not need to be completed for those type of shipments.

For all shipments the Contractor shall package and ship each end item individually. All exterior shipping containers/packaging shall at a minimum be marked with the following information: Part Number; Nomenclature;

Quantity; Serial number; Contract Number; National Stock Number; and Manufacturer’s Name, Address, and CAGE Code.

Deliveries shall be made within six (6) months after order receipt. Early delivery is acceptable and encouraged.

4.5 Shipping Document

The Contractor shall notify Robert Hull, Phone (732) 323-4611, email address: robert.m.hull30.civ@us.navy.mil when the shipment is ready and to confirm the shipping address. Upon shipment, a copy of the shipping document and tracking documents shall be emailed to robert.m.hull30.civ@us.navy.mil and edan.s.rosenberg-hayes.civ@us.navy.mil.

5.0 POINTS OF CONTACT

To Be Filled In At Contract Award

CTXT.211-9510 CONTRACTOR EMPLOYEES (NAVAIR) (MAY 2011)

(a) In all situations where contractor personnel status is not obvious, all contractor personnel are required to identify themselves to avoid creating an impression to the public, agency officials, or Congress that such contractor personnel are Government officials. This can occur during meeting attendance, through written (letter or email) correspondence or verbal discussions (in person or telephonic), when making presentations, or in other situations where their contractor status is not obvious to third parties. This list is not exhaustive. Therefore, the contractor employee(s) shall:

(1) Not by word or deed give the impression or appearance of being a Government employee;

(2) Wear appropriate badges visible above the waist that identify them as contractor employees when in Government spaces, at a Government-sponsored event, or an event outside normal work spaces in support of the contract/order;

(3) Clearly identify themselves as contractor employees in telephone conversations and in all formal and informal written and electronic correspondence. Identification shall include the name of the company for whom they work;

(4) Identify themselves by name, their company name, if they are a subcontractor the name of the prime contractor their company is supporting, as well as the Government office they are supporting when participating in meetings, conferences, and other interactions in which all parties are not in daily contact with the individual contractor employee; and

(5) Be able to provide, when asked, the full number of the contract/order under which they are performing, and the name of the Contracting Officer’s Representative.

(b) If wearing a badge is a risk to safety and/or security, then an alternative means of identification maybe utilized if endorsed by the Contracting Officer’s Representative and approved by the Contracting Officer.

(c) The Contracting Officer will make final determination of compliance with regulations with regard to proper identification of contractor employees.

Section D - Packaging and Marking

DTXT.247-9508 PROHIBITION AND LIMITATIONS FOR PACKAGING MATERIALS

(NAVAIR) (AUG 2019)

The use of loose fill materials, asbestos, excelsior, newspaper and shredded paper (all types) are prohibited. In addition, all Wood Packaging Materials (WPM) shall be heat treated or chemically treated in accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15:2009, "Regulation of Wood Packaging Material in International Trade."

DTXT.247-9514 TECHNICAL DATA PACKING INSTRUCTIONS (NAVAIR)(SEP 1999)

Technical Data and Information shall be packed and packaged for domestic shipment in accordance with best commercial practices. The package or envelope should be clearly marked with any special markings specified in this contract (or delivery/task order), e.g., Contract Number, CLIN, Device No., and document title must be on the outside of the package. Classified reports, data and documentation, if applicable, shall be prepared for shipment in accordance with Defense Industrial Manual for Safeguarding Classified Information, DoD 5220.22M.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

1001 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

1002 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

2001 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

2002 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

3001 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

3002 NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government NAVAL AIR WARFARE CENTER

AD (LKE)

HWY 547, BLDG 120

LAKEHURST NJ 08733

Government

CLAUSES INCORPORATED BY REFERENCE

52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-15 Certificate of Conformance APR 1984

ETXT.246-9512 INSPECTION AND ACCEPTANCE (NAVAIR)(OCT 2005)

(a) Inspection and acceptance of the supplies or services to be furnished hereunder shall be performed by an authorized Government representative at destination.

(b) Acceptance of all Contract Line Items/Sub Line Items (CLINs/SLINs) shall be made by signature of the accepting authority on a DD 250 submitted through the WAWF system. Acceptance will only occur when the accepting authority is sure that inspections performed demonstrate compliance with contract requirements.

ETXT.246-9514 INSPECTION AND ACCEPTANCE OF TECHNICAL DATA AND INFORMATION

(NAVAIR)(FEB 1995)

Inspection and acceptance of technical data and information will be performed by the Procuring Contracting Officer (PCO) or his duly authorized representative. Inspection of technical data and information will be performed by ensuring successful completion of the requirements set forth in the DD Form 1423, Contract Data Requirements List (CDRL) and incorporation/resolution of Government review comments on the data items. Acceptance will be evidenced by execution of an unconditional DD Form 250, Material Inspection and Receiving Report, as appropriate, and/or upon receipt of a second endorsement acceptance by the PCO on the attachment to this contract entitled N/A. The attached form will not be used for high cost data such as drawings, specifications, and technical manuals.

Section F - Deliveries or Performance

ACCELERATED DELIVERY

Accelerated delivery to the greatest extent possible in advance of the specified delivery schedule is acceptable and encouraged. Any acceptable delivery shall be at no additional cost to the Government.

52.242-15 Stop-Work Order AUG 1989 52.242-17 Government Delay Of Work APR 1984 52.247-34 F.O.B. Destination NOV 1991

52.211-8 TIME OF DELIVERY (JUN 1997)

(a) The Government requires delivery to be made according to the following schedule:

REQUIRED DELIVERY SCHEDULE

CLIN EST. MAX QUANTITY DATE DELIVERY ADDRESS

1001 5 Each Units shall be delivered within 6 months after date of order.

Two units shall be delivered to:

NAWCAD Lakehurst SE Staging Facility NAWCAD Lakehurst, Rt. 547

HANGAR 1

Joint Base MDL, NJ 08733 Mark For: MQ-4C USN Program POC: Robert Hull

One unit shall be delivered to:

NAVSUP FLTLOGCEN Jacksonville Detachment, Gulfport, MS (RIC 4NN) 511 North Brown Ave, BLDG 437 Gulfport, MS 39501-5000 ATTN: RIC 4NN, DoDAAC N6694N POC: Penny Prestage

Remaining units shall be delivered to:

DODAAC: SW310N

DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

1002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

As specified on the individual Contract Data Requirements Lists (CDRLs)

2001 2 Each Units shall be delivered within 6 months after date of order.

DODAAC: SW310N

DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

2002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

As specified on the individual Contract Data Requirements Lists (CDRLs)

3001 1 Each Units shall be delivered within 6 months after date of order.

DODAAC: SW310N

DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

3002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

The Government will evaluate equally, as regards time of delivery, offers that propose delivery of each quantity within the applicable delivery period specified above. Offers that propose delivery that will not clearly fall within the applicable required delivery period specified above will be considered nonresponsive and rejected. The Government reserves the right to award under either the required delivery schedule or the proposed delivery schedule, when an offeror offers an earlier delivery schedule than required above. If the offeror proposes no other delivery schedule, the required delivery schedule above will apply.

OFFEROR'S PROPOSED DELIVERY SCHEDULE

CLIN EST. MAX QUANTITY DATE DELIVERY ADDRESS

1001 5 Each Two units shall be delivered to:

NAWCAD Lakehurst SE Staging Facility NAWCAD Lakehurst, Rt. 547

HANGAR 1

Joint Base MDL, NJ 08733 Mark For: MQ-4C USN Program POC: Robert Hull

One unit shall be delivered to:

NAVSUP FLTLOGCEN Jacksonville Detachment, Gulfport, MS (RIC 4NN) 511 North Brown Ave, BLDG 437 Gulfport, MS 39501-5000 ATTN: RIC 4NN, DoDAAC N6694N POC: Penny Prestage

Remaining units shall be delivered to:

DODAAC: SW310N

DLA Distribution Susquehanna PA

Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

1002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

As specified on the individual Contract Data Requirements Lists (CDRLs)

2001 2 Each DODAAC: SW310N DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

2002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

As specified on the individual Contract Data Requirements Lists (CDRLs)

3001 1 Each DODAAC: SW310N DLA Distribution Susquehanna PA Mechanicsburg Receiving West 5450 Carlisle Pike, Bldg. 402 Mechanicsburg, PA 17050-0789

MARK FOR: RIC5Q4 (MQ-4C)

POC: Robert Hull

FOB: DESTINATION

3002 1 Lot As specified on the individual Contract Data Requirements Lists (CDRLs)

(b) Attention is directed to the Contract Award provision of the solicitation that provides that a written award or acceptance of offer mailed or otherwise furnished to the successful offeror, results in a binding contract. The Government will mail or otherwise furnish to the offeror an award not later than the day award is dated. Therefore, the offeror should compute the time available for performance beginning with the actual date of award, rather than the date the written notice of award is received from the Contracting Officer through the ordinary mails. However, the Government will evaluate an offer that proposes delivery based on the Contractor’s date of receipt of the contract or notice of award by adding (1) five calendar days for delivery of the award through the ordinary mails, or

(2) one working day if the solicitation states that the contract or notice of award will be transmitted electronically.

(The term “working day” excludes weekends and U.S. Federal holidays.) If, as so computed, the offered delivery date is later than the required delivery date, the offer will be considered nonresponsive and rejected.

FTXT.247-9505 TECHNICAL DATA AND INFORMATION (NAVAIR)(FEB 1995)

Technical Data and Information shall be delivered in accordance with the requirements of the Contract Data Requirements List, DD Form 1423, Exhibit A, attached hereto, and the following:

(a) The contractor shall concurrently deliver technical data and information per DD Form 1423, Blocks 12 and 13 (date of first/subsequent submission) to all activities listed in Block 14 of the DD Form 1423 (distribution and addresses) for each item. Complete addresses for the abbreviations in Block 14 are shown in paragraph (g) below.

Additionally, the technical data shall be delivered to the following cognizant codes, who are listed in Block 6 of the DD Form 1423.

(1) PCO, Code N/A.

(2) ACO, Code N/A.

(b) Partial delivery of data is not acceptable unless specifically authorized on the DD Form 1423, or unless approved in writing by the PCO.

(c) The Government review period provided on the DD Form 1423 for each item commences upon receipt of all required data by the technical activity designated in Block 6.

(d) A copy of all other correspondence addressed to the Contracting Officer relating to data item requirements (i.e., status of delivery) shall also be provided to the codes reflected above and the technical activity responsible for the data item per Block 6, if not one of the activities listed above.

(e) The PCO reserves the right to issue unilateral modifications to change the destination codes and addresses for all technical data and information at no additional cost to the Government.

(f) Unless otherwise specified in writing, rejected data items shall be resubmitted within thirty (30) days after receipt of notice of rejection.

(g) DD Form 1423, Block 14 Mailing Addresses: See Exhibit A

Section G - Contract Administration Data

252.232-7003 Electronic Submission of Payment Requests and Receiving

Reports

DEC 2018

252.232-7006 WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)

(a) Definitions. As used in this clause—

“Department of Defense Activity Address Code (DoDAAC)” is a six position code that uniquely identifies a unit, activity, or organization.

“Document type” means the type of payment request or receiving report available for creation in Wide Area WorkFlow (WAWF).

“Local processing office (LPO)” is the office responsible for payment certification when payment certification is done external to the entitlement system.

“Payment request” and “receiving report” are defined in the clause at 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports.

(b) Electronic invoicing. The WAWF system provides the method to electronically process vendor payment requests and receiving reports, as authorized by Defense Federal Acquisition Regulation Supplement (DFARS) 252.232- 7003, Electronic Submission of Payment Requests and Receiving Reports.

(c) WAWF access. To access WAWF, the Contractor shall—

(1) Have a designated electronic business point of contact in the System for Award Management at https://www.sam.gov; and

(2) Be registered to use WAWF at https://wawf.eb.mil/ following the step-by-step procedures for self-registration available at this web site.

(d) WAWF training. The Contractor should follow the training instructions of the WAWF Web-Based Training Course and use the Practice Training Site before submitting payment requests through WAWF. Both can be accessed by selecting the “Web Based Training” link on the WAWF home page at https://wawf.eb.mil/.

(e) WAWF methods of document submission. Document submissions may be via web entry, Electronic Data Interchange, or File Transfer Protocol.

(f) WAWF payment instructions. The Contractor shall use the following information when submitting payment requests and receiving reports in WAWF for this contract or task or delivery order:

(1) Document type. The Contractor shall submit payment requests using the following document type(s):

(i) For cost-type line items, including labor-hour or time-and-materials, submit a cost voucher.

(ii) For fixed price line items—

(A) That require shipment of a deliverable, submit the invoice and receiving report specified by the Contracting Officer.

___To Be Filled In Upon Contract Award_________________________________________________________

(Contracting Officer: Insert applicable invoice and receiving report document type(s) for fixed price line items that require shipment of a deliverable.)

(B) For services that do not require shipment of a deliverable, submit either the Invoice 2in1, which meets the requirements for the invoice and receiving report, or the applicable invoice and receiving report, as specified by the Contracting Officer.

(Contracting Officer: Insert either “Invoice 2in1” or the applicable invoice and receiving report document type(s) for fixed price line items for services.)

(iii) For customary progress payments based on costs incurred, submit a progress payment request.

(iv) For performance based payments, submit a performance based payment request.

(v) For commercial financing, submit a commercial financing request.

(2) Fast Pay requests are only permitted when Federal Acquisition Regulation (FAR) 52.213-1 is included in the contract.

[Note: The Contractor may use a WAWF “combo” document type to create some combinations of invoice and receiving report in one step.]

(3) Document routing. The Contractor shall use the information in the Routing Data Table below only to fill in applicable fields in WAWF when creating payment requests and receiving reports in the system.

Routing Data Table*

Field Name in WAWF Data to be entered in WAWF

Pay Official DoDAAC TBD

Issue By DoDAAC TBD

Admin DoDAAC** TBD

Inspect By DoDAAC TBD

Ship To Code TBD

Ship From Code TBD

Mark For Code TBD

Service Approver (DoDAAC) TBD

Service Acceptor (DoDAAC) TBD

Accept at Other DoDAAC TBD

LPO DoDAAC TBD

DCAA Auditor DoDAAC TBD

Other DoDAAC(s) TBD

(*Contracting Officer: Insert applicable DoDAAC information. If multiple ship to/acceptance locations apply, insert “See Schedule” or “Not applicable.”)

(**Contracting Officer: If the contract provides for progress payments or performance-based payments, insert the DoDAAC for the contract administration office assigned the functions under FAR 42.302(a)(13).)

(4) Payment request. The Contractor shall ensure a payment request includes documentation appropriate to the type of payment request in accordance with the payment clause, contract financing clause, or Federal Acquisition Regulation 52.216-7, Allowable Cost and Payment, as applicable.

(5) Receiving report. The Contractor shall ensure a receiving report meets the requirements of DFARS Appendix F.

(g) WAWF point of contact.

(1) The Contractor may obtain clarification regarding invoicing in WAWF from the following contracting activity’s WAWF point of contact.

____ To Be Filled In Upon Contract Award________________________________________________________

(Contracting Officer: Insert applicable information or “Not applicable.”)

(2) Contact the WAWF helpdesk at 866-618-5988, if assistance is needed.

(End of clause)

GTXT.232-0001 PAYMENT INSTRUCTIONS (NAVAIR) (MAY 2023)

For Government Use Only

Contract/Order Payment Clause

Type of Payment Request

Su pp ly

Se rv ic e

C on st ru ct io n

Payment Office Allocation Method

52.212-4 (Alt I), Cost Voucher X X N/A Line item specific proration.

Contract Terms and If there is more than one ACRN Conditions— within a deliverable contract line Commercial Products item, the funds will be allocated in and Commercial the same proportion as the Services; amount of funding currently 52.216-7, Allowable unliquidated for each ACRN on Cost and Payment; the line item billed.

52.232-7, Payments Under Time-and- Materials and Labor- Hour Contracts

52.232-1, Payments, Navy X X N/A Line item specific by fiscal year.

252.217-7007, Shipbuilding If there is more than one ACRN Payments Invoice (Fixed within a deliverable line or (vessel repair and alterations) Price) deliverable subline item, the funds will be allocated using the oldest funds first. In the event of a deliverable line or deliverable subline item with two or more ACRNs with the same fiscal year, those amounts will be prorated to the available unliquidated funds for that year.

52.232-1, Payments; Invoice X X N/A Line item specific proration.

52.232-2, Payments If there is more than one ACRN Under Fixed-Price within a deliverable line item or Research and deliverable subline item, the Development funds will be allocated in the Contracts; same proportion as the amount 52.232-3, Payments of funding currently unliquidated Under Personal for each ACRN on the deliverable Services Contracts; line or deliverable subline item for 52.232-4, Payments which payment is requested.

Under Transportation Contracts and Transportation-Related Services Contracts; and 52.232-6, Payments Under Communication Service Contracts With Common Carriers st ru ct

52.232-5, Payments Under Fixed-Price Construction Contracts

Construction Payment Invoice

N/A N/A X Line item specific by fiscal year. If there is more than one ACRN within a deliverable line or deliverable subline item, the funds will be allocated using the oldest funds first. In the event of a deliverable line or deliverable subline item with two or more ACRNs with the same fiscal year, those amounts will be prorated to the available unliquidated funds for that year.

52.232-16, Progress Progress X X N/A Contract-wide proration.

Payments Payment* Funds shall be allocated in the (excluding contracts same proportion as the amount with multiple lot of funding currently unliquidated progress payments) for each ACRN. Progress payments are considered contract level financing, and the “contract price” shall reflect the fixed-price portion of the contract per FAR 32.501-3.

52.232-16, Progress Payments;

252.232-7018, Progress Payments— Multiple Lots

Progress Payment*

X X N/A Lot-wide proration (applies to lots specifically identified in the contract).

If there is more than one ACRN within a lot, the funds will be allocated in the same proportion as the amount of funding currently unliquidated for each ACRN on the lot for which payment is requested.

See PGI 204.7108 paragraph (c) for multiple lot CLIN structure.

st ru ct

52.232-29, Terms for Financing of Purchases of Commercial Products and Commercial Services;

52.232-30, Installment Payments for Commercial Products and Commercial Services

Commercial Product and Commercial Service Financing*

X X N/A Specified in approved payment. The contracting officer shall specify the amount to be paid and the account(s) to be charged for each payment approval in accordance with FAR 32.207(b)(2).

52.232-32, Performance-Based Payments

Performance- Based Payments*

X X N/A Specified in approved payment. The contracting officer shall specify the amount to be paid and the account(s) to be charged for each payment approval in accordance with FAR 32.1007(b)(2).

252.232-7002, Progress Payments for Foreign Military Sales Acquisitions

Progress Payment*

X X N/A Allocate costs among line items and countries in a manner acceptable to the administrative contracting officer.

*Liquidation of Financing Payments. Liquidation will be applied by the payment office against those ACRNs which are identified by the payment instructions for the delivery payment and in keeping with the liquidation provision of the applicable contract financing clause (i.e., progress payment, performance-based payment, or commercial product and commercial service financing).

Section H - Special Contract Requirements

HTXT.216-9512 PAPERLESS CONTRACTING (NAVAIR)(JUN 2009)

(a) Orders and requests for proposals are hereby authorized to be issued by facsimile or by electronic commerce (including e-mail and paperless methods of delivery). Nothing in this contract should be read to prohibit these types of orders. In the event of a conflict with any other provision of this contract, this clause shall govern.

(b) To the extent the terms "written", "mailed", or "physically delivered" appear in other provisions of this contract, these terms are hereby defined to explicitly include electronic commerce, email, or paperless delivery methods.

Section I - Contract Clauses

52.203-12 Limitation On Payments To Influence Certain Federal

Transactions

JUN 2020

52.204-13 System for Award Management Maintenance OCT 2018 52.204-18 Commercial and Government Entity Code Maintenance AUG 2020 52.204-19 Incorporation by Reference of Representations and

Certifications.

DEC 2014

52.204-21 Basic Safeguarding of Covered Contractor Information Systems

NOV 2021

52.204-27 Prohibition on a ByteDance Covered Application JUN 2023 52.209-10 Prohibition on Contracting With Inverted Domestic

Corporations

NOV 2015

52.211-5 Material Requirements AUG 2000 52.211-15 Defense Priority And Allocation Requirements APR 2008 52.215-8 Order of Precedence--Uniform Contract Format OCT 1997 52.219-6 Notice Of Total Small Business Set-Aside NOV 2020 52.225-13 Restrictions on Certain Foreign Purchases FEB 2021 52.226-8 Encouraging Contractor Policies To Ban Text Messaging

While Driving

MAY 2024

52.232-40 Providing Accelerated Payments to Small Business Subcontractors

MAR 2023

52.243-1 Changes--Fixed Price AUG 1987 52.244-6 Subcontracts for Commercial Products and Commercial

Services

FEB 2024

52.249-1 Termination For Convenience Of The Government (Fixed Price) (Short Form)

APR 1984

52.249-8 Default (Fixed-Price Supply & Service) APR 1984 252.203-7000 Requirements Relating to Compensation of Former DoD

Officials

SEP 2011

252.203-7002 Requirement to Inform Employees of Whistleblower Rights DEC 2022 252.204-7000 Disclosure Of Information OCT 2016 252.204-7003 Control Of Government Personnel Work Product APR 1992 252.204-7008 Compliance With Safeguarding Covered Defense Information

Controls

OCT 2016

252.204-7012 (Dev) Safeguarding Covered Defense Information and Cyber Incident Reporting (DEVIATION 2024-O0013 REVISION 1)

MAY 2024

252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support

JAN 2023

252.204-7018 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services

JAN 2023

252.204-7020 NIST SP 800-171 DoD Assessment Requirements NOV 2023 252.204-7022 Expediting Contract Closeout MAY 2021 252.209-7004 Subcontracting With Firms That Are Owned or Controlled By

The Government of a Country that is a State Sponsor of Terrorism

MAY 2019

252.211-7003 Item Unique Identification and Valuation JAN 2023 252.211-7008 Use of Government-Assigned Serial Numbers SEP 2010 252.223-7008 Prohibition of Hexavalent Chromium JAN 2023 252.225-7002 Qualifying Country Sources As Subcontractors MAR 2022

252.225-7007 Prohibition on Acquisition of Certain Items from Communist Chinese Military Companies

DEC 2018

252.225-7012 Preference For Certain Domestic Commodities APR 2022 252.225-7013 Duty-Free Entry--Basic NOV 2023 252.225-7048 Export-Controlled Items JUN 2013 252.225-7972 (Dev) Prohibition on the Procurement of Foreign-Made Unmanned

Aircraft Systems (DEVIATION 2020-O0015)

MAY 2020

252.232-7010 Levies on Contract Payments DEC 2006 252.243-7001 Pricing Of Contract Modifications DEC 1991 252.244-7000 Subcontracts for Commercial Products or Commercial

Services

NOV 2023

252.247-7023 Transportation of Supplies by Sea JAN 2023

52.213-4 TERMS AND CONDITIONS--SIMPLIFIED ACQUISITIONS (OTHER THAN COMMERCIAL

PRODUCTS AND COMMERCIAL SERVICES) (MAY 2024)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses that are incorporated by reference:

(1) The clauses listed below implement provisions of law or Executive order:

(i) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L.

113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(ii) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab Covered Entities (DEC 2023) (Section 1634 of Pub. L. 115-91).

(iii) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (NOV 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(iv) 52.204-27, Prohibition on a ByteDance Covered Application (JUN 2023) (Section 102 of Division R of Pub. L.

117-328), unless the agency grants an exception--see paragraph (b) of 52.204-27.

(v) 52.204-30, Federal Acquisition Supply Chain Security Act Orders--Prohibition. (DEC 2023) (Pub. L. 115-390, title II).

(vi) 52.222-3, Convict Labor (JUN 2003) (E.O. 11755).

(vii) 52.222-21, Prohibition of Segregated Facilities (APR 2015).

(viii) 52.222-26, Equal Opportunity (SEPT 2016) (E.O. 11246).

(ix) 52.225-13, Restrictions on Certain Foreign Purchases (FEB 2021) (E.O.s, proclamations, and statutes administered by the Office of Foreign Assets Control of the Department of the Treasury).

(x) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (MAR 2023) (31 U.S.C. 3903 and 10 U.S.C. 3801).

(xi) 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553).

(xii) 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Pub. L. 108-77 and 108-78 (19 U.S.C.

3805 note)).

(2) Listed below are additional clauses that apply:

(i) 52.232-1, Payments (APR 1984).

(ii) 52.232-8, Discounts for Prompt Payment (FEB 2002).

(iii) 52.232-11, Extras (APR 1984).

(iv) 52.232-25, Prompt Payment (JAN 2017).

(v) 52.232-39, Unenforceability of Unauthorized Obligations (JUN 2013).

(vi) 52.233-1, Disputes (MAY 2014).

(vii) 52.244-6, Subcontracts for Commercial Products and Commercial Services (FEB 2024).

(viii) 52.253-1, Computer Generated Forms (JAN 1991).

(b) The Contractor shall comply with the following FAR clauses, incorporated by reference, unless the circumstances do not apply:

(1) The clauses listed below implement provisions of law or Executive order:

(i) 52.203-17, Contractor Employee Whistleblower Rights (NOV 2023) (41 U.S.C. 4712); this clause does not apply to contracts of DoD, NASA, the Coast Guard, or applicable elements of the intelligence community--see FAR 3.900(a).

(ii) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (JUN 2020) (Pub. L. 109-

282) (31 U.S.C. 6101 note) (Applies to contracts valued at or above the threshold specified in FAR 4.1403(a) on the date of award of this contract).

(iii) 52.222-19, Child Labor--Cooperation with Authorities and Remedies (FEB 2024) (E.O. 13126) (Applies to contracts for supplies exceeding the micro-purchase threshold, as defined in 2.101 on the date of award of this contract).

(iv) 52.222-20, Contracts for Materials, Supplies, Articles, and Equipment (JUN 2020) (41 U.S.C. chapter 65) (Applies to supply contracts over the threshold specified in FAR 22.602 on the date of award of this contract, in the United States, Puerto Rico, or the U.S. Virgin Islands).

(v) 52.222-35, Equal Opportunity for Veterans (JUN 2020) (38 U.S.C. 4212) (Applies to contracts valued at or above the threshold specified in FAR 22.1303(a) on the date of award of this contract).

(vi) 52.222-36, Equal Employment for Workers with Disabilities (JUN 2020) (29 U.S.C. 793) (Applies to contracts over the threshold specified in FAR 22.1408(a) on the date of award of this contract, unless the work is to be performed outside the United States by employees recruited outside the United States).