N6660418R0132_with_Attachments.pdf

CODE

(Hour)

PAGE(S)

until 02:00 PM local time 10 Jul 2018

X

A

X B

X C X D

EX

X

G

F 54 - 62

63 - 68

X H 69 - 73 paul.lee3@navy .mil

RATING PAGE OF PAGES

7. ISSUED BY

(Date)

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

Previous Edition is Unusable 33-134 STANDARD FORM 33 (REV. 9-97)

Prescribed by GSA

FAR (48 CFR) 53.214(c)

DO-C9 1 73

(If other than Item 7)

15A. NAME 16. NAME AND TITLE OF PERSON AUTHORIZED TO

AND

ADDRESS

SIGN OFFER (Type or print)

OF

OFFEROR

AMENDMENT NO. DATE

15B. TELEPHONE NO (Include area code) 17. SIGNATURE15C. CHECK IF REMITTANCE ADDRESS

IS DIFFERENT FROM ABOVE - ENTER

SUCH ADDRESS IN SCHEDULE.

18. OFFER DATE

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

2. CONTRACT NO.

N66604 8. ADDRESS OFFER TO

See Item 7

9. Sealed offers in original and 1 copies for furnishing the supplies or services in the Schedule will be received at the place specified in Item 8, or if handcarried, in the depository located in

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and

See Section L - Email Submittal conditions contained in this solicitation.

10. FOR INFORMATION

CALL:

A. NAME (NO COLLECT CALLS)

PAUL LEE (401) 832-4358

11. TABLE OF CONTENTS

SOLICITATION/ CONTRACT FORM

SUPPLIES OR SERVICES AND PRICES/ COSTS

1 - 2

3 - 20

X I CONTRACT CLAUSES

DESCRIPTION/ SPECS./ WORK STATEMENT X

PACKAGING AND MARKING

21 - 28

29 - 31

J LIST OF ATTACHMENTS

INSPECTION AND ACCEPTANCE

DELIVERIES OR PERFORMANCE

32 - 34

35 - 39 X K

REPRESENTATIONS, CERTIFICATIONS AND

OTHER STATEMENTS OF OFFERORS

CONTRACT ADMINISTRATION DATA 40 - 43 X

SPECIAL CONTRACT REQUIREMENTS

OFFER (Must be fully completed by offeror) 44 X M

L INSTRS., CONDS., AND NOTICES TO OFFERORS

EVALUATION FACTORS FOR AWARD

NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the price set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. DISCOUNT FOR PROMPT PAYMENT

(See Section I, Clause No. 52.232-8)

14. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments

AMENDMENT NO. DATE

to the SOLICITATION for offerors and related documents numbered and dated):

FACILITY

12. In compliance with the above, the undersigned agrees, if this offer is accepted within calendar days (60 calendar days unless a different period

SOLICITATION, OFFER AND AWARD

X

(X) SEC. DESCRIPTION (X) SEC. DESCRIPTION PAGE(S)

PART I - THE SCHEDULE

26. NAME OF CONTRACTING OFFICER (Type or print) 27. UNITED STATES OF AMERICA 28. AWARD DATE

EMAIL:TEL: (Signature of Contracting Officer)

CODE CODE

B. TELEPHONE (Include area code) C. E-MAIL ADDRESS

AWARD (To be completed by Government)

19. ACCEPTED AS TO ITEMS NUMBERED 20. AMOUNT 21. ACCOUNTING AND APPROPRIATION

22. AUTHORITY FOR USING OTHER THAN FULL AND OPEN COMPETITION:

10 U.S.C. 2304(c)( ) 41 U.S.C. 253(c)( ) (4 copies unless otherwise specified)

23. SUBMIT INVOICES TO ADDRESS SHOWN IN ITEM

24. ADMINISTERED BY (If other than Item 7) CODE 25. PAYMENT WILL BE MADE BY CODE

PART IV - REPRESENTATIO NS AND INSTRUCTIO NS

PART III - LIST O F DO CUMENTS, EXHIBITS AND O THER ATTACHMENTS

45 - 52

PART II - CO NTRACT CLAUSES

NAVAL UNDERSEA WARFARE CENTER

PAUL LEE, CODE 0224

CONTRACTS DEPARTMENT

1176 HOWELL STREET, BLDG. 1258

NEWPORT RI 02841-1708

(401) 832-4358

FAX:

TEL:

FAX:

TEL:

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder".

SOLICITATION

6. REQUISITION/PURCHASE NO.5. DATE ISSUED

08 Jun 2018

4. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

[ X ]

3. SOLICITATION NO.

N6660418R0132

Section A - Solicitation/Contract Form

CLAUSES INCORPORATED BY FULL TEXT

GENERAL INFORMATION

Distribution: FILE, KR, NUWC 01, DCM: TBD, DFAS: TBD, COR: TBD, PI: TBD; WAWF: TBD

NUWCDIVNPT Control Number: 180132

NUWCDIVNPT Requisition Number(s): 1300631962

NUWCDIVNPT POC: Paul Lee (Phone: (401) 832-4358; Fax: (401) 832-4820; Email: paul.lee3@navy.mil)

NOTE: The delivery information listed in Section F of this Request For Proposal is based on an anticipated award date of 30 SEP 2018. The delivery information will be revised at the time of award.

Section B - Supplies or Services and Prices

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

0001 3 Each Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW) in Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

FOB: Destination

PSC CD: 3120

NET AMT

0002 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0003 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0004 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0005 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0006 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0007 2 Each OPTION Aft Thrust Bearing Assembly

FFP

Aft Thrust Bearing Assemblies in accordance with Drawing 6407178 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0008 3 Each Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0009 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0010 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0011 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0012 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0013 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0014 2 Each OPTION Forward Thrust Bearing Assembly

FFP

Forward Thrust Bearing Assemblies in accordance with Drawing 6407179 and the

Statement of Work (SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0015 6 Each Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0016 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0017 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0018 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0019 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0020 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0021 4 Each OPTION Radial Bearings

FFP

Radial Bearings in accordance with Drawing 6407176 and the Statement of Work

(SOW), Section C.

NOTE: The requirements in DFARS 252.211-7003, Item Identification and

Valuation, are applicable for this line item. The contractor shall provide DoD unique identification or a DoD recognized unique identification equivalent.

0022 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

PSC CD: J020

0023 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0024 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0025 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0026 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0027 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0028 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0029 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0030 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0031 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0032 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0033 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0034 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0035 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0036 1 Job OPTION Aft Thrust Bearing Repair

FFP

Aft Thrust Bearing Repair in accordance with the Statement of Work (SOW), Section C.

0037 1 Lot

DATA

FFP

Data in accordance with Exhibit A, Contract Data Requirements List, (CDRLs)

(with Addendum), DD Form 1423.

NOT SEPARATELY PRICED

HQ B-2-0010 NOTE (OPTION)

NOTE B - Option item to which the option clause in SECTION I-2 applies and which is to be supplied only if and to the extent said option is exercised.

HQ B-2-0022 CONTRACT SUMMARY FOR PAYMENT OFFICE (FIXED PRICE) (FEB 1997)

This entire contract is fixed price.

Section C - Descriptions and Specifications

STATEMENT OF WORK (SOW)

BEARING ASSEMBLIES AND COMPONENTS

1.0 BACKGROUND

Naval Undersea Warfare Center Division Newport (NUWCDIVNPT) Platform and Payload Integration Department

(Code 40) is the In-Service Engineering Agent (ISEA) for the Air Turbine Pump (ATP) and is the primary activity that has the ability and qualifications to overhaul ATP Bearing Cartridges (BC) assemblies. These assemblies are critical internal subassemblies to the ATP and contain multiple bearing components that may need repair or replacement during BC overhaul. BC overhaul during dry-dock availability. NUWCDIVNPT is being tasked directly by multiple Naval Shipyards to perform BC overhauls for platforms during planned dry-docking availabilities. This effort is critical to meeting dry docking milestones of the Fleet.

The material acquired under this contract will be used in a crucial shipboard system. The use of incorrect or defective material will create a high probability of failure resulting in serious personnel injury, loss of life, loss of vital shipboard systems, or loss of the ship itself. Therefore, the material has been designated as Special Emphasis

SUBSAFE / Level I material and special control procedures are invoked to ensure receipt of correct material.

2.0 SCOPE

The contractor shall fabricate new or repair existing BC assemblies, as well as inspect the components as tasked in

Section 4 of this Statement of Work (SOW). The hardware shall be manufactured in strict accordance with this

SOW and with the drawings and documents listed in Section 3 of this SOW. All hardware shall be manufactured in accordance with strict quality control guidelines as identified herein.

2.1 Place of Performance

The place of performance of this contract shall be at the contractor’s site.

2.2 Authorized Users

NUWC Code 40 is the only authorized user of this contract.

2.3 Sponsors

Sponsors for this contract are all Naval Shipyards (Portsmouth Naval Shipyard, Norfolk Naval Shipyard, Puget

Sound Naval Shipyard, and/or Pearl Harbor Naval Shipyard), PMS392, and/or SEA05.

2.4 Type of Funding

Operations & Maintenance, Navy (O&MN) will be provided for this contract.

3.0 APPLICABLE DOCUMENTS

The contractor shall perform the requirements of this SOW in accordance with the following documents.

Applicability of Appendix A or Appendix F for each part or assembly is listed below for clarity.

3.1 Drawings

No. Description

Applicable

Appendix

SOW

Task

3.1.1 Dwg 6407178 Rev D, Aft Thrust Bearing Assy (SUBSAFE/LEVEL I) App A 4.1

└─Dwg 6407170 Rev B, Aft Thrust Collar (SUBSAFE/LEVEL I) App A

└─Dwg 6407177 Rev D, Aft Thrust Bearing App F

└─Add material specification “MIL-R-46198, TY-II, CL-3, FORM – M”

3.1.2 Dwg 6407179 Rev D, Fwd Thrust Bearing Assembly App F 4.2

│ └─In zone 1F4, change parallelism from 0.002” to 0.0041”

│ └─In Note 4, do not allow for accelerated cure time of the adhesive.

│ └─Note 4, use primer on the pad pockets in lieu of the etching process.

└─Dwg 6407172 Rev A, Fwd Thrust Bearing Retainer App F

└─Dwg 6407173 Rev C, Fwd Thrust Bearing App F

└─In zone 1B7, change flatness requirement from 0.002” to 0.004”

3.1.3 Dwg 6407176 Rev C, Radial Bearing App F 4.3

4.0 TECHNICAL REQUIREMENTS

The minimum quality requirements for procurement, modification, repair, or overhaul of Non-Nuclear Level I

Material and Level I support are provided in SOW Appendix A, “Minimum Standard Quality Contract

Requirements for Procurement, Modification, Repair or Overhaul of Non-Nuclear Level I Material.” Appendix A is an integral part of this contract. The contractor shall comply with the requirements established in SOW Appendix A.

The minimum quality requirements for procurement, modification, repair, or overhaul of Non-Level SUBSAFE

Material are provided in SOW Appendix F, “Minimum Standard Quality contract Requirements for Procurement, Modification, Repair or Overhaul of Non-Level Subsafe Boundary Material.” Appendix F is an integral part of this contract. The contractor shall comply with the requirements established in SOW Appendix F.

Additional operational/technical specifications are identified in the following paragraphs to this SOW.

4.1 Aft Thrust Bearing Assembly – SUBSAFE/LEVEL I

In accordance with Applicable Documents (ADs) in Section 3.1.1, the contractor shall manufacture and deliver up to

FIFTEEN (15) SUBSAFE/LEVEL I Aft Thrust Bearing Assemblies and deliver supporting documentation.

4.1.1 Deliverables: The contractor shall deliver the following with EACH Aft Thrust Bearing Assembly delivered:

Certificate of Compliance in accordance with (IAW) CDRL A001;

Mercury Free Certification IAW CDRL A002;

Material Certification/Test Report IAW CDRL A003; and

Deviation/Waiver (if requested by contractor) IAW CDRL A005.

4.1.2 Assembly Procedure:

• Prior to the start of manufacture, the contractor shall provide an Assembly Procedure for review and approval. The contractor shall only begin assembly of the Aft Thrust Bearing Assembly with a Government approved Assembly Procedure.

4.1.2.1 Deliverables: The contractor shall deliver the assembly procedure in accordance with CDRL A009.

4.2 Forward Thrust Bearing Assembly

In accordance with ADs in Section 3.1.2, the contractor shall manufacture and deliver up to FIFTEEN (15) Forward

Thrust Bearing Assemblies and deliver supporting documentation.

4.2.1 Deliverables: The contractor shall deliver the following for EACH Forward Thrust Bearing assembly:

Certificate of Compliance IAW CDRL A001;

Request for Deviation/Waiver (if requested by contractor) IAW CDRL A005.

4.2.2 Assembly Procedure:

• Prior to the start of manufacture, the contractor shall provide an Assembly Procedure for review and approval. The contractor shall only begin assembly of the Forward Thrust Bearing Assembly with a Government approved assembly procedure.

4.2.2.1 Deliverables: The contractor shall deliver an Assembly Procedure in accordance with CDRL A009.

4.3 Radial Bearings

In accordance with AD 3.1.3, the contractor shall manufacture and deliver up to THIRTY (30) Radial Bearings and deliver supporting documentation.

4.3.1 Deliverables: The contractor shall deliver the following for EACH Radial Bearing:

Certificate of Compliance IAW CDRL A001;

Material Certification/Test Report IAW CDRL A003; and

Request for Deviation/Waiver (if requested by contractor) IAW CDRL A005.

4.4 Repair of Aft Thrust Bearing Assembly (SUBSAFE/LEVEL 1)

The contractor shall repair individual Aft Thrust Bearing Assemblies, AD 3.1.1, drawing 6407178, and provide supporting documentation. The Government will provide up to FIFTEEN (15) Aft Thrust Bearing Assemblies as

Government Furnished Property (GFP) to the contractor for repair, including a List of Acceptable Defects (LAD) provided as Government Furnished Information (GFI) 5.1 that will not require repair.

The repair shall consist of the basic steps listed below, as detailed in SOW Tasks 4.4.3—4.4.8:

• Removal of the Vespel bearing material

• Removal of all adhesive residue

• Detailed Inspection Plan (DIP) and Non-Destructive Testing (NDT) inspections

• Installation of new Thrust Bearings to existing Thrust Collar

• Final machining to meet AD 3.1.1 requirement

Repair procedures to accomplish these steps shall be developed by the contractor, as tasked in 4.4.2, and shall require Government approval. Defects identified on the LAD are exempt from correction during machining.

4.4.1 Receipt Inspection:

Upon receipt of each Aft Thrust Bearing Assembly for repair, the contractor shall conduct a receipt inspection of the component to confirm that the GFP component can be repaired within the scope of the standard repair as specified in

SOW Tasks 4.4.3 – 4.4.8 and that all visible defects are identified in the LAD. The contractor shall maintain all traceability numbers marked on the parts and contained in the accompanying documentation. If the contractor determines the GFP component cannot be repaired within the scope of the standard repair as specified in SOW

Tasks 4.4.3 – 4.4.8, the contractor shall stop further work, document any concerns, and contact the Contracting

Officer’s Representative for disposition guidance.

4.4.2 Repair and Assembly Procedure:

Prior to starting the first repair on this contract, the contractor shall prepare and submit an Overhaul and Assembly

Procedure for review and approval. On subsequent repair options, if exercised, the contractor shall use the same

Overhaul and Assembly Procedure or prepare and submit any revised procedure for review and approval.

4.4.2.1 Deliverable: The contractor shall deliver the Repair and Assembly Procedure of Aft Thrust Bearing

Assemblies for approval in accordance with CDRL A009.

4.4.3 Bearing Pad Removal

The contractor shall remove the worn bearing pads from the Aft Thrust Bearing Assembly in accordance with the

Government-approved Overhaul and Assembly Procedure submitted per SOW Task 4.4.2.

4.4.4 Detailed Inspection of Aft Thrust Collar (AD 3.1.1, drawing 6407170)

Upon 4.4.3 Bearing Pad Removal, the contractor shall prepare a Detailed Inspection Plan (DIP) and provide a completed DIP report documenting the 100% inspection of the features of the Aft Thrust Collar as defined on the governing drawing. The DIP and DIP Report shall be prepared in accordance with SOW Appendix A.

4.4.4.1 Deliverable: The contractor shall deliver a 100% DIP & Report of the Aft Thrust Collar (AD 3.1.1, drawing 6407170) in accordance with CDRL A004.

4.4.5 Aft Thrust Collar NDT Inspection

The contractor shall conduct liquid penetrant NDT inspection of the Aft Thrust Collar after bearing pad removal in accordance with SOW Appendix A.

4.4.5.1 Deliverable: The contractor shall deliver a NDT report of the Aft Thrust Collar (AD 3.1.1, drawing

6407170) in accordance with CDRL A008.

4.4.6 Aft Thrust Bearing Fabrication and Installation

The contractor shall fabricate new Aft Thrust Bearing pads IAW AD 3.1.1, drawing 6407177. The contractor shall install the Aft Thrust Bearing pads into the Aft Thrust Collar in accordance with the Government-approved

Overhaul and Assembly Procedure submitted per SOW Task 4.4.2.

4.4.7 Final Machining of the Aft Thrust Bearing Assembly

The contractor shall perform machining operations to return the Aft Thrust Bearing Assembly to conformance with

AD 3.1.1, drawing 6407178.

4.4.8 Detailed Inspection of Aft Thrust Bearing Assembly (AD 3.1.1, drawing 6407178)

The contractor shall prepare a DIP and provide a completed DIP Report for 100% inspection of the features of the

Aft Thrust Bearing Assembly as defined on the governing drawing. The DIP and DIP Report shall be prepared in accordance with SOW Appendix A.

4.4.8.1 Deliverable: The contractor shall deliver a 100% Detailed Inspection Plan & Report of the Aft

Thrust Bearing Assembly (AD 3.1.1, drawing 6407178) in accordance with CDRL A004.

4.4.9 Quality Assurance:

4.4.9.1 Deliverables: The contractor shall deliver the following for EACH Aft Thrust Bearing assembly repaired:

• Certificate of Compliance in accordance with (IAW) CDRL A001;

• Mercury Free Certification IAW CDRL A002;

• Material Certification/Test Report IAW CDRL A003; and

• Request for Deviation/Waiver (if requested by contractor) IAW CDRL A005.

4.5 Detailed Inspection Plans

The contractor shall prepare a 100% DIP and complete a DIP Report for all components and assemblies delivered under Tasks 4.1 through 4.3. The DIP and the completed DIP Report shall form part of the Objective Quality

Evidence (OQE) for accepting the components and assemblies. The DIP and DIP Report shall be prepared in accordance with SOW Appendix A for Task 4.1 and SOW Appendix F for Tasks 4.2, 4.3.

The DIP shall define 100% of the drawing characteristics for the component and the DIP Report shall document and record the inspection results for each characteristic. For a dimensional characteristic, the DIP shall identify the drawing requirement including location of the characteristic by drawing zone, tolerance allowance, the measurement results, the measurement equipment used and a signature or stamp of the operator performing the inspection. For a procedural characteristic, the process must be witnessed or OQE must be available to verify the performance of the process. The DIP shall indicate when a process is either witnessed or verified through OQE.

4.6 Quality Control Procedures

The contractor shall develop inspection system procedures as required by SOW Appendix A.

4.6.1 Deliverables: The contractor shall deliver Inspection Systems Procedures in accordance with CDRL

A006 and Non-Destructive Testing (RT, UT, VT) Procedures per CDRL A007.

4.7 Parts Marking

In addition to the marking requirements in accordance with the drawings, SOW Appendix A, and SOW Appendix F, the contractor shall mark each metallic component and assembly with the following:

• Part Number, Find Number and Revision Level

• Supplier Cage Code/Trademark (if applicable)

• NUWCDIVNPT supplied Serial Number

• Deviation / Waiver numbers approved

All required markings are to be applied in accordance with SOW Appendix A or the drawing. All required markings are to be made in the area indicated on the controlling drawings.

4.8 Shipping – Applicable To All CLINS.

Completed components shall be shipped in accordance with the delivery schedule and have the Unique

Identification (UID) tag attached with a tie and not adhered to a part.

5.0 GOVERNMENT FURNISHED INFORMATION (GFI)

5.1 List of Acceptable Defects (LAD)

6.0 QUALITY SURVEILLANCE AND PERFORMANCE STANDARDS

The Government will conduct quality surveillance via various methods including formal and informal meetings, review of technical reports, review of monthly progress reports, and review of deliverables. Contractor performance will be evaluated in the areas of technical quality, schedule/timeliness, management, and regulatory compliance as follows:

Technical Quality: The Government will evaluate technical quality against the requirements set forth in this

SOW and using the criteria defined in the Performance Requirements Summary Table (PRST), Attachment

3;

Schedule/Timeliness: The Government will evaluate the contractor’s ability to meet negotiated milestones and delivery schedules;

Management: The Government will evaluate the contractor’s ability to integrate and coordinate all activities needed to execute the contract;

Regulatory Compliance: The Government will evaluate the contractor’s compliance with the terms and conditions of the contract relating to applicable regulations and codes.

ENTERPRISE CONTRACTOR MANPOWER REPORTING APPLICATION (ECMRA)

The contractor shall report contractor labor hours (including subcontractor labor hours) required for performance of services provided under this contract for the Naval Undersea Warfare Center Division, Newport via a secure data collection site. Contracted services excluded from reporting are based on Product Service Codes (PSCs). The excluded PSCs are:

(1) W, Lease/Rental of Equipment;

(2) X, Lease/Rental of Facilities;

(3) Y, Construction of Structures and Facilities;

(4) D, Automatic Data Processing and Telecommunications, IT and Telecom- Telecommunications Transmission

(D304) and Internet (D322) ONLY;

(5) S, Utilities ONLY;

(6) V, Freight and Shipping ONLY.

The contractor is required to completely fill in all required data fields using the following web address https://www.ecmra.mil/.

Reporting inputs will be for the labor executed during the period of performance during each Government fiscal year

(FY), which runs October 1 through September 30. While inputs may be reported any time during the FY, all data shall be reported no later than October 31 of each calendar year. Contractors may direct questions to the help desk, linked athttps://www.ecmra.mil/.

HQ C-1-0001 ITEM(S) - DATA REQUIREMENTS (NAVSEA) (SEP 1992)

The data to be furnished hereunder shall be prepared in accordance with the Contract Data Requirements List, DD

Form 1423, Exhibit A, attached hereto.

HQ C-2-0008 ASSIGNMENT AND USE OF NATIONAL STOCK NUMBERS (NAVSEA) (MAY 1993)

To the extent that National Stock Numbers (NSNs) or preliminary NSNs are assigned by the Government for the identification of parts, pieces, items, subassemblies or assemblies to be furnished under this contract, the Contractor shall use such NSNs or preliminary NSNs in the preparation of provisioning lists, package labels, packing lists, shipping containers and shipping documents as required by applicable specifications, standards or Data item

Descriptions of the contract or as required by orders for spare and repair parts. The cognizant Government Contract

Administration Office shall be responsible for providing the Contractor such NSNs or preliminary NSNs which may be assigned and which are not already in possession of the Contractor.

HQ C-2-0023 EXCLUSION OF MERCURY (NAVSEA) (MAY 1998)

Mercury or mercury containing compounds shall not be intentionally added or come in direct contact with hardware or supplies furnished under this contract.

HQ C-2-0032 INFORMATION AND DATA FURNISHED BY THE GOVERNMENT - ALTERNATE II

(NAVSEA) (SEP 2009)

(a) NAVSEA Form 4340/2 or Schedule C, as applicable, Government Furnished Information, attached hereto, incorporates by listing or specific reference, all the data or information which the Government has provided or will provide to the Contractor except for

(1) The specifications set forth in Section C, and

(2) Government specifications, including drawings and other Government technical documentation which are referenced directly or indirectly in the specifications set forth in Section C and which are applicable to this contract as specifications, and which are generally available and provided to Contractors or prospective Contractors upon proper request, such as Federal or Military Specifications, and Standard Drawings, etc.

(b) Except for the specifications referred to in subparagraphs (a)(1) and (2) above, the Government will not be obligated to provide to the Contractor any specification, drawing, technical documentation or other publication which is not listed or specifically referenced in NAVSEA Form 4340/2 or Schedule C, as applicable, notwithstanding anything to the contrary in the specifications, the publications listed or specifically referenced in

NAVSEA Form 4340/2 or Schedule C, as applicable, the clause entitled "GOVERNMENT PROPERTY" (FAR

52.245-1) or "GOVERNMENT PROPERTY INSTALLATION OPERATION SERVICES " (FAR 52.245-2), as applicable, or any other term or condition of this contract.

(c)(1) The Contracting Officer may at any time by written order:

(i) delete, supersede, or revise, in whole or in part, data listed or specifically referenced in NAVSEA Form

4340/2 or Schedule C, as applicable; or

(ii) add items of data or information to NAVSEA Form 4340/2 or Schedule C, as applicable; or

(iii) establish or revise due dates for items of data or information in NAVSEA Form 4340/2 or Schedule C, as applicable.

(2) If any action taken by the Contracting Officer pursuant to subparagraph (c)(1) immediately above causes an increase or decrease in the costs of, or the time required for, performance of any part of the work under this contract, the contractor may be entitled to an equitable adjustment in the contract amount and delivery schedule in accordance with the procedures provided for in the "CHANGES" clause of this contract.

HQ C-2-0051 SPECIFICATIONS AND STANDARDS (NAVSEA) (AUG 1994)

(a) Definitions.

(i) A "zero-tier reference" is a specification, standard, or drawing that is cited in the contract (including its attachments).

(ii) A "first-tier reference" is either: (1) a specification, standard, or drawing cited in a zero-tier reference, or (2) a specification cited in a first-tier drawing.

(b) Requirements.

All zero-tier and first-tier references, as defined above, are mandatory for use. All lower tier references shall be used for guidance only.

HQ C-2-0059 UPDATING SPECIFICATIONS AND STANDARDS (NAVSEA) (AUG 1994)

If, during the performance of this or any other contract, the contractor believes that any contract contains outdated or different versions of any specifications or standards, the contractor may request that all of its contracts be updated to include the current version of the applicable specification or standard. Updating shall not affect the form, fit or function of any deliverable item or increase the cost/price of the item to the Government. The contractor should submit update requests to the Procuring Contracting Officer with copies to the Administrative Contracting Officer and cognizant program office representative for approval. The contractor shall perform the contract in accordance with the existing specifications and standards until notified of approval/disapproval by the Procuring Contracting

Officer. Any approved alternate specifications or standards will be incorporated into the contract.

Section D - Packaging and Marking

HQ D-1-0001 PACKAGING OF DATA

Data to be delivered by Integrated Digital Environment (IDE) or other electronic media shall be as specified in the contract.

All unclassified data to be shipped shall be prepared for shipment in accordance with best commercial practice.

Classified reports, data, and documentation shall be prepared for shipment in accordance with National Industrial

Security Program Operating Manual (NISPOM), DOD 5220.22-M dated 28 February 2006 with Change 2 dated 18

May 2016.

HQ D-2-0005 IDENTIFICATION MARKING OF PARTS – ALTERNATE I (NAVSEA)(APR 2015)

(a) Identification marking of individual parts within the systems, equipments, assemblies, subassemblies, components, groups, sets or kits, and of spare and repair parts shall be done in accordance with applicable specifications and drawings.

To the extent identification marking of such parts is not specified in applicable specifications or drawings, such marking shall be accomplished in accordance with the following:

(1) Parts not manufactured to Government specifications shall be marked in accordance with generally accepted commercial practice.

(2) Parts manufactured to Government specifications shall be marked as follows:

(i) Electrical Parts - that is, all parts in electrical equipments and electrical parts when used in equipments which are not electrical in nature (e.g., electric controls and motors in a hydraulic system) - shall be identified and marked in accordance with MIL-STD-1285D(1) dated 10 November 2010, or, where MIL-STD-1285D(1) does not cover such a part, in accordance with MIL-STD-130N(1) dated 16 November 2012. Requirements of MIL-STD-1686C dated 25 October 1995 for Electrostatic Discharge Control shall be addressed.

(ii) Electronic Parts - that is, all parts in electronic equipments and electronic parts when used in equipments which are not electronic in nature (e.g., electronic fuel controls in some engines) - shall be identified and marked in accordance with Requirement 67 of MIL-HDBK-454B dated 15 April 2007. Requirements of MIL-STD-1686C for

Electrostatic Discharge Control shall be addressed.

(iii) Parts other than electrical or electronic parts (as described above) shall be identified and marked in accordance with MIL-STD-130N(1).

(b) In cases where parts are so small as not to permit identification marking as provided above, such parts shall be appropriately coded so as to permit ready identification.

HQ D-2-0007 MARKING AND PACKING LIST(S) - ALTERNATE I (NAVSEA) (APR 2015)

(a) Marking. Shipments, shipping containers and palletized unit loads shall be marked in accordance with MIL-STD-

129R dated 18 February 2014.

(b) Packing List(s). A packing list (DD Form 250 Material Inspection and Receiving Report may be used) identifying the contents of each shipment, shipping container or palletized unit load shall be provided by the Contractor with each shipment in accordance with the above cited MIL-STD. When a contract line item identified under a single stock number includes an assortment of related items such as kit or set components, detached parts or accessories, installation hardware or material, the packing list(s) shall identify the assorted items.

Where DD Form 1348-1 or DD Form 1348-1A is applicable and an assortment of related items is included in the shipping container, a packing list identifying the contents shall be furnished.

(c) Master Packing List. In addition to the requirements in paragraph (b) above, a master packing list shall be prepared where more than one shipment, shipping container or palletized unit load comprise the contract line item being shipped.

The master packing list shall be attached to the number one container and so identified.

(d) Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items.

HQ D-2-0008 MARKING OF REPORTS (NAVSEA) (SEP 1990)

All reports delivered by the Contractor to the Government under this contract shall prominently show on the cover of the report:

(1) name and business address of the Contractor

(2) contract number

(3) contract dollar amount

(4) whether the contract was competitively or non-competitively awarded

(5) sponsor:

(Name of Individual Sponsor)

(Name of Requiring Activity)

(City and State)

UW D-2-0001 MARK FOR INFORMATION (AUG 2017)

(a) The Contractor shall include the following “Mark For” information clearly marked on all packages (or items themselves if they are not packaged) delivered under this contract/order:

Mark For:

Receiving Officer, Naval Station Newport

47 Chandler Street

Newport, RI 02841-1716

NUWC Division, Newport Code TBD

Contract #: TBD

UW D-2-0002 PROHIBITED PACKING MATERIALS (MAR 2017)

The use of asbestos, excelsior, newspaper, or shredded paper (all types including waxed paper, computer paper, and similar hygroscopic or non-neutral material) is prohibited. In addition, loose fill polystyrene is prohibited for shipboard use.

UW D-2-0003 UNPACKING INSTRUCTIONS (MAR 2017)

(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked

"UNPACKING INFORMATION".

(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION-

THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE

CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED (state where located)." When practical, this marking will be applied adjacent to the identification marking on the side of the container.

Section E - Inspection and Acceptance

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

0001 Destination Government Destination Government

0002 Destination Government Destination Government

0003 Destination Government Destination Government

0004 Destination Government Destination Government

0005 Destination Government Destination Government

0006 Destination Government Destination Government

0007 Destination Government Destination Government

0008 Destination Government Destination Government

0009 Destination Government Destination Government

0010 Destination Government Destination Government

0011 Destination Government Destination Government

0012 Destination Government Destination Government

0013 Destination Government Destination Government

0014 Destination Government Destination Government

0015 Destination Government Destination Government

0016 Destination Government Destination Government

0017 Destination Government Destination Government

0018 Destination Government Destination Government

0019 Destination Government Destination Government

0020 Destination Government Destination Government

0021 Destination Government Destination Government

0022 Destination Government Destination Government

0023 Destination Government Destination Government

0024 Destination Government Destination Government

0025 Destination Government Destination Government

0026 Destination Government Destination Government

0027 Destination Government Destination Government

0028 Destination Government Destination Government

0029 Destination Government Destination Government

0030 Destination Government Destination Government

0031 Destination Government Destination Government

0032 Destination Government Destination Government

0033 Destination Government Destination Government

0034 Destination Government Destination Government

0035 Destination Government Destination Government

0036 Destination Government Destination Government

0037 Destination Government Destination Government

CLAUSES INCORPORATED BY REFERENCE

52.246-2 Inspection Of Supplies--Fixed Price AUG 1996

52.246-4 Inspection Of Services--Fixed Price AUG 1996

52.246-16 Responsibility For Supplies APR 1984

252.246-7000 Material Inspection And Receiving Report MAR 2008

52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)

(a) The Contractor shall comply with the higher-level quality standard(s) listed below.

ISO9001:2008 or later

(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph

(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--

(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or

(2) When the technical requirements of a subcontract require--

(i) Control of such things as design, work operations, in-process control, testing, and inspection; or

(ii) Attention to such factors as organization, planning, work instructions, documentation control, and advanced metrology.

(End of clause)

HQ E-1-0001 INSPECTION AND ACCEPTANCE LANGUAGE FOR DATA

Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD

Form 1423.

HQ E-2-0008 INSPECTION AND TEST RECORDS (NAVSEA) (MAY 1995)

Inspection and Test Records: Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness.

HQ E-2-0017 USE OF CONTRACTOR’S INSPECTION EQUIPMENT (NAVSEA) (MAY 1995)

Use of Contractor’s Inspection Equipment: The contractor's gages, and measuring and testing devices shall be made available for use by the Government when required to determine conformance with contract requirements. If conditions warrant, the contractor’s personnel shall be made available for operations of such devices and for verification of their accuracy and condition.

UW E-2-0001X NOTIFICATION OF INSPECTION OR TEST (MAR 2017)

(a) The material under this contract is designated as Special Emphasis SUBSAFE/LEVEL I material. In accordance with Statement of Work (SOW) Appendices A and F, the contractor is required to perform all inspections to ensure the quality of the finished item and for providing inspection and test equipment necessary to ensure the results of inspections and tests are accurate. Note that the aforementioned inspections required by SOW Appendices A and F are prior to shipment from the source and in addition to the inspection performed by the Government upon delivery of the items at the location specified in the DELIVERY INFORMATION Section of the contract.

(b) In accordance with SOW Appendices A and F, the contractor agrees to notify the Certifying Activity (CA) when the material will be inspected and/or tested. A minimum of seven working days is required to arrange such a visit.

(c) The contractor also agrees to notify the Procuring Contracting Officer, the Negotiator, and the Contracting

Officer’s Representative (COR) Point of Contact as listed in UW G-2-0002, in writing, when the material will be inspected and/or tested. A minimum of seven working days is required to arrange such a visit.

Section F - Deliveries or Performance

52.242-15 Stop-Work Order AUG 1989

52.242-17 Government Delay Of Work APR 1984

52.247-34 F.O.B. Destination NOV 1991

DELIVERY INFORMATION

CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

0001 10 mths. ADC 3 NAVAL STATION NEWPORT, N66604

RECEIVING OFFICER

SEE CLAUSE UW D-2-0001

--- RI

401-841-3827

N66604

0002 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0003 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0004 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0005 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0006 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0007 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0008 10 mths. ADC 3 (SAME AS PREVIOUS LOCATION)

0009 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0010 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0011 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0012 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0013 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0014 10 mths. AOE 2 (SAME AS PREVIOUS LOCATION)

0015 8 mths. ADC 6 (SAME AS PREVIOUS LOCATION)

0016 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0017 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0018 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0019 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0020 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0021 8 mths. AOE 4 (SAME AS PREVIOUS LOCATION)

0022 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0023 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0024 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0025 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0026 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0027 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0028 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0029 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0030 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0031 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0032 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0033 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0034 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0035 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0036 6 mths. AOE 1 (SAME AS PREVIOUS LOCATION)

0037 58 mths. ADC 1 (SAME AS PREVIOUS LOCATION)

52.211-8 TIME OF DELIVERY (JUN 1997)

(a) The Government requires delivery to be made according to the following schedule:

REQUIRED DELIVERY SCHEDULE

CLIN Description Quantity/Unit of Issue Delivery Date

0001 Aft Thrust Bearings 3 Each 10 months ADC

0002 – Option Aft Thrust Bearings 2 Each 10 months AOE

0003 – Option Aft Thrust Bearings 2 Each 10 months AOE

0004 – Option Aft Thrust Bearings 2 Each 10 months AOE

0005 – Option Aft Thrust Bearings 2 Each 10 months AOE

0006 – Option Aft Thrust Bearings 2 Each 10 months AOE

0007 – Option Aft Thrust Bearings 2 Each 10 months AOE

0008 Forward Thrust Bearings 3 Each 10 months ADC

0009 – Option Forward Thrust Bearings 2 Each 10 months AOE

0010 – Option Forward Thrust Bearings 2 Each 10 months AOE

0011 – Option Forward Thrust Bearings 2 Each 10 months AOE

0012 – Option Forward Thrust Bearings 2 Each 10 months AOE

0013 – Option Forward Thrust Bearings 2 Each 10 months AOE

0014 – Option Forward Thrust Bearings 2 Each 10 months AOE

0015 Radial Bearings 6 Each 8 months ADC

0016 – Option Radial Bearings 4 Each 8 months…